ProScan PS36605YX3CK2, PS27600YX2AP, PS32600YX2CK2, PS36615YX1CK2, PS32700YX2CJ4 User Manual
...
TV
USER'S MANUAL
P S
.... %
S
iiiiiii¸
IMPORTANT INFORMATION
[
WARNING
To reduce the risk of fire or shock
hazard, do not expose this TV to
rain or moisture.
]o reduce the risk of electric shock, do not remove
RISKOF ELECTRIC cover (or back). No user serviceable parts inside. Refer
SHOCK DO NOT OPEN servicing to qualified service personnel.
,_ This symbol indicates ,_ This symbol indicates
"dangerous voltage" inside the important instructions
product that presents a risk of accompanying the product,
electric shock or personal injury,
Caution: To reduce the risk of electric shock, match wide
blade of plug to wide slot, fully insert.
Attention: Pour dviter les chocs electriques, introduire la lame
la plus large de la fiche dans la borne correspondante de la
prise et pousserjusqO au fond.
Refer to the identification/rating label located on the back
panel of your product for its proper operating voltage.
FCC Regulations state that unauthorized changes or modifications to this
equipment may void the user's authority to operate it.
If fixed (non-moving) images are left on the screen for long periods, they may
be permanently imprinted on the screen. Such images include network Iogos,
phone numbers, and video games. This damage is not covered by your
warranty. Extended viewing of channels displaying these images should be
avoided.
Cable TV Installer: This reminder is provided to call your attention to Article
820-40 of the National Electrical Code (Section 54 of the Canadian Electrical
Code, Part 1) which provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the
building as close to the point of cable entry as practical.
VCR Plus+, C_rPhsCode and GUIDE Plus+ are trademarks of Gemstar Development Corporation
The VCR Plus+ and GUIDE Plus+ systems are manufactured under license from Gemstar Development Corporation and VCR index Systems BV,
respectively
GEMSTAR IS NOT IN ANY WAY LIABLE FORTHE ACCURACY OF THE PROGRAM SCHEDULE INFORMATION PROVIDED BYTHE
GUIDE PLUS+ SYSTEM. IN NO EVENT SHALL GEMSTAR BE LIABLE FORANY AMOUNT REPRESENTING LOSS OF PROFITS, LOSS
OF BUSINESS, OR INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE PROVISION OR USE OF
ANY INFORMATION, EQUIPMENT, OR SERVICESRELATING TO THE GUIDE PLUS+ SYSTEM.
VCR required for recording
TABLE OF CONTENTS
SETUP AND CONNECTIONS ............................................ 3
Step 1: Unpack the TV ..................................................... 4
Step 2: Connecting your TV ............................................. 4
Step 3: Connecting the IR Controller ................................ 9
Step 4: Plug in the TV .................................................... 10
Step 5: Place Batteries in Remote ................................... 10
Step 6: Turn on the TV ................................................... 10
On-Screen Program Guide ....................................... 10
Step 7: Program the TV .................................................. 10
INTERACTIVE SETUP .......................................................... 11
Using Point and Select ................................................... 12
Entering Setup ................................................................ 12
Select a Language .......................................................... 13
Auto Channel Search ..................................................... 13
The GUIDE Plus+ Gold System ...................................... 14
Setting the Time ............................................................. 16
Setting the VCR1 Channel (auto tuning) ........................ 16
Setting the VCR2 Channel (auto tuning) ......................... 17
Setting the DVD Channel (auto tuning) .......................... 18
Setting the SAT/CABLE Channel (auto tuning) ................ 19
Labeling the Channels ................................................... 20
USING THE REMOTE .......................................................... 21
Remote Buttons ............................................................. 22
Accessing the Video Input ........................................ 23
Programming the Remote .............................................. 24
Testing the Remote ................................................... 24
Using Automatic Code Search .................................. 24
Using Direct Entry .................................................... 24
Using the Remote to Control a Device ..................... 25
Modes of Operation ................................................. 25
Front Panel .................................................................... 25
TABLE OF CONTENTS
FEATURES AND MENUS .................................................... 27
Menus and Control Panels ............................................. 28
Menus ...................................................................... 28
Control Panels .......................................................... 29
Audio Menu .................................................................. 30
Using the Remote to Select an Audio Processor ............. 31
Picture Quality Menu .................................................... 32
Screen Menu ................................................................. 33
Using Closed Captioning .......................................... 34
Closed Captioning Modes ........................................ 34
Turning off Closed Captioning .................................. 34
Channel Menu ............................................................... 35
Time Menu .................................................................... 36
Parental Controls and V-Chip ......................................... 37
V-Chip TV Rating Limit ............................................. 38
Channel Block .......................................................... 43
Front Panel Block ..................................................... 43
Lock/Unlock Parental Controls ................................. 43
GUIDE Plus+ Gold System ............................................ 44
Downloading Data ................................................... 45
News ........................................................................ 48
Schedule .................................................................. 48
Messages .................................................................. 49
Editor ....................................................................... 50
PIP (Picture-in-Picture) Operation .................................. 51
Setup Menu ................................................................... 52
Channel Marker ............................................................. 52
REFERENCE ............................................................................. 53
Troubleshooting ............................................................. 54
Making Connections to the Front Panel ......................... 56
Care and Cleaning ......................................................... 56
PROSCAN TV LIMITED WARRANTY ....................... 57
Accessory Information .............................................. 58
Index ............................................................................... 61
2
SETUP AND
GET rING STARTED
This manual is designed to get you S{_r
The first four sections of the m
quickly,
the
to get yourTV Setup and Cc
Interactive Setup, Program the Rem_ and use allQf
the Features and MenOs of your TV,
The Reference section in the back book
contains troubleshooting Zips,care a cleaning
instructions, accessory ord6ring iation and your
warranty
!{!i
4 FEATURES
5 REFERENCE
US
%
%
Check out the notes that have been |
J
added throughout the manual in these
Tip Boxes. There are some important
tips that will help you get the most from
your TV,
3
SETUP AND CONNECTIONS
STEP1: UNPACK THETV
Make sure to locate the remote control.
STEP2: CONNECTING YOURTV
There are three types of connections outlined in this section:
TV Only:
The Basic Connection:
If you're only going to connect the
TV to your home antenna or cable
system.
If you're going to connect the TV to a
VCR or satellite receiver.
Advanced Connections:
If you're going to make multiple
connections, hooking up the TV to
one or two VCRs, DVD player, and a
satellite receiver.
Cable information and illustrations are given for each type of
connection. Once you have completed your desired connection you
may skip forward to Step 3.
TV ONLY
This is a basic connection from an antenna or cable system to your TV.
Connect the cable into the Cable/Antenna jack as shown.
CABLES
You will use the following cable to make your connection:
Coaxial Cable: These cables carry audio and video
signal to the TV from an antenna, cable, or cable
box.
Important Stand Information
Direct View TVs: 27"- 36" diagonal
CAUTION: Choose the location for your
TV carefully, lake precautions that the
stand or other furniture the TV is placed
on is properly located (see Important
Safeguards sheet) and of adequate size
and strength to prevent the TV from
accidentally being tipped over, pushed
off, or pulled off. This could cause
damage to the TV and/or personal injury.
r-
Before You Connect
Protect against power surges:
• Connect all components before
plugging any power cords into the wall
outlet.
• ]urn offthe TV and/or component
before connecting or disconnecting
any cables.
• Make sure all antennas and cables are
properly grounded. Refer to the Safety
Tips sheet packed with your TV.
CABLE, CABLE BOX, OR ANTENNA
Once you have completed this connection go to Step 3, on page 9.
our TV May Differ 1
odel PS27600 does not have an
-Video jack for INPUT2 nor external
peaker terminals,
4
SETUP AND CONNECTIONS
THE BASIC CONNECTION
The basic connection below (TV and VCR) is the most common
connection and is therefore used to illustrate a single component
connection with your TV. For better sound and picture quality and
multiple component connection information refer to the next section,
Advanced Connections.
CABLES
You will use the following cable to make your connection:
Coaxial Cables: These cables carry both the audio
and video signal to the TV from an antenna, cable,
or cable box. In this connection, a second Coaxial
Cable carries the signal through the VCR to the TV.
CABLE, CABLE BOX, OR ANTENNA
How TO VIEW THE VCR
lo watch the VCR in this connection tune TV to
Channel 3 or 4.
Later, in the Interactive Setup section you will
program the TV to automatically tune to Channel 3
or 4 when you turn on the VCR.
Once you have completed this connection go to Step 3, on page 9.
Your TV May Differ 1
Model PS27600 does not have an
S-Videojack for INPUT2 nor external
speaker terminals.
5
SETUP AND CONNECTIONS
ADVANCED CONNECTIONS
Advanced connections give you better sound and video by separating
the audio and video signals and enable you to connect multiple
components.
This section describes the types of inputs available on the back of your
TV and suggests ways you can use them for optimum performance.
BACK OE THETV
The diagram below describes each of the back panel jacks. When
connecting A/V cables, be sure to connect corresponding OUTPUTS
and INPUTS (Video to Video, Right Audio to Right Audio, etc.).
Once you have made your connections
you will want to program the TV to tune
to the correct Video INPUT channel in
order to see and hear audio and video
from the component. You will program
this later in the Interactive Setup.
Input 1
Connect any of the following components:
• VCR • Internet Access Device
• Laserdisc Player • DVD Player
• Satellite Receiver
]o view the component connected to Input 1:
Use the WHO•INPUT button on the remote.
Input 2
Connect any of the following components:
• VCR • Internet Access Devic_
• Laserdisc Player • DVD Player
• Satellite Receiver
]o view the component connected to Input 2:
Use the WHO•INPUT button on the remote.
S-Video
This optional
connection
can be used
for better
video quality
picture.
INPUT 2
INPUT 1 VIDEO R_UDIO L S V_DEO
,op@ e
Speaker Terminals*
Use to connect external
speakers for surround sound.
Make sure the Speaker
Selection is set to
EXTERNAL.
S-Video
rhis optional connection car
be used for better video
quality picture.
Audio Outputs
audio receiver or
amplifier for variable controlled
or fixed level stereo output.
Cable/Antenna
signal input from a cable,
cable box, or an off-air antenna. Can
also be used for basic component
connections.
VCR Control
Connect Guide Plus+
controller for one-button
recording and channel
tuning from the Guide.
*Model PS27600 does not have these features.
6
SETUP AND CONNECTIONS
SAMPLE CONNECTIONS
The following are sample connection scenarios which you may
encounter when connecting components to your TV.
CABLES
You will use the following cable to make your connection:
Coaxial Cables: Carries the signal from the
antenna or cable directly to the television or
through a cable box, as needed by your cable
system.
Audio/Video Cables: Carries sound and video
from the component to the TV.
S-Video Cable: Carries video from an S-Video
capable component which provides best
picture quality.
TV AND STEREoVCR
CABLE, CABLE BOX, OR ANTENNA
Once you have completed this connection go to Step 3,
on page 9.
Cautions:
Position cables to Avoid Audio Hum or
Interference
• Insert all cables firmly into jacks.
• Place the audio/video cables to the
sides of the TV's back panel instead of
straight down the middle.
• ]ry not to coil any twin-lead cables
and keep them away from the audio/
video cables.
Protect your components from
Overheating
• Do not block ventilation holes in any
of the components. Arrange the
components so that air can circulate
freely.
• Do not stack components.
• Allow adequate ventilation when
placing your components in a stand.
• Place an amplifier on the top shelf of
the stand so heated air rising from it
will not flow around other
components.
How TOVIEwYouRVCR
]o watch the VCR in this connection, press TV to put the
remote control into TV mode, then press WHO,INPUT to
scroll through the video input channels until you tune to
VlD1 input.
In the Interactive Setup section you can program the TV
to automatically tune to the VlD1 input channel when
you press VCR1 on the remote.
Most Audio/Video cables are combined
into one cable with three heads on each
end.
We show individual Video(eHow)
cables in these
sample _iRight Audlo(red)
connections. Either
may be used, but )
you must be sure to
connect Video to Video, Right to Right
and Left to Left,
7
SETUP AND CONNECTIONS
TV, VCR AND SATELLITE RECEIVER
CABLE, CABLE BOX, OR ANTENNA
SATELLITE RECEIVER
VC}
SATELLITE
How TO VIEwYOuR COMPONENTS
]o watch the Satellite Receiver in this connection,
press TV to put the remote control into TV mode, then
press WHO,INPUT to scroll through the video input
channels until you tune to VlD1 (or SVlD 1) input.
]o watch the VCR in this connection, press TV to put
the remote control into TV mode, then press
WHO,INPUT to scroll through the video input
channels until you tune to VlD2 (or SVlD 2) input.
In the Interactive Setup you can program the TV to
automatically tune to the correct input channel when
you press the component button on the remote.
Once you have completed this connection go to Step 3,
on page 9.
TV, VCR, SATELLITERECEIVERANDDVD
CABLE, CABLE BOX, OR ANTENNA
SATELUTE RECEIVER
VCR
SATELLITE
How TO VIEwYOuR COMPONENTS
To watch the Satellite Receiver in this connection, press
TV to put the remote control into TV mode, then press
WHO*INPUT to scroll through the video input
channels until you tune to VlD1 (or SVlD 1) input.
To watch the VCR in this connection tune to Channel 3
or 4.
To watch the DVD player in this connection, press TV
to put the remote control into TV mode, then press
WHO*INPUT to scroll through the video input
channels until you tune to VlD2 (or SVlD 2) input.
In the Interactive Setup you can program the TV to
automatically tune to the correct input channel when
you press the component button on the remote.
Once you have completed this connection go to Step 3,
on page 9.
8
SETUP AND CONNECTIONS
STEP3: CONNECTING THE IRCONTROLLER
The IR (Infrared) Controller enables GUIDE Plus+ Gold to control your
VCR and cable box (if necessary) so that you can tune to television
channels and even start recording a program from the program guide,
After you have affixed the ends of the controller to the necessary
devices (VCR, or Cable box), you will use the on-screen interactive
setup routine for GUIDE Plus+ to test the connected devices,
The IR Controller is used to send commands to yourVCR
and/or cable box.
ATTACHING THE IRCONTROLLERS
Some components label the infrared remote sensor, and others do not.
If your component is labeled, affix the IR controller directly over the
sensor. For components that do not label the remote sensor, you need
to use the component's remote control to locate the sensor.
1. Hold the component's remote control (not the remote that came
with your TV) so that it is touching the front of the component.
2,
Slowly move the remote over the front of the component while
pressing the remote power button on and off. (Be sure to press and
release the power button each time you move the remote. Holding
the button may not work.)
3.
4.
When the component turns off or on, you've located the sensor.
Affix the controller's node directly to the remote sensor.
TV
d_o__...................
I I .......
> I,H []
_°- °. °° °° °• °o--, °°, ,"//'
_o°° Al_ach 1olhe Cable Box {if yo_ have _ne)
A_ach [o VCR
otherwise just _eave it una_ched
Connected to the TV
9
SETUP AND CONNECTIONS
STEP4: PLUG IN THETV
Plug the end into the wall outlet, matching the wide blade of the plug
with the wide slot in the outlet, Be sure to insert the plug completely,
STEP 5: PLACE BATTERIES IN REMOTE
Remove the battery compartment cover from the back of the
remote.
Insert fresh batteries. Make sure that the polarities (+ and -) are
aligned correctly.
Replace the cover.
STEP6:TURN ON THETV
Press TV on the remote, or press POWER on the TV itself.
Pressing the TV button not only turns on the TV, but puts the remote
into TV mode, so that the buttons on the remote will control TV
functions.
ON-SCREEN PROGRAM GUIDE
The TV is designed to bring up the GUIDE Plus+ on-screen program
guide when you use the TV button on the remote to turn on the TV
(after you have set up the GUIDE Plus+ system). For more information,
see the GUIDE Plus+ Features & Setup booklet.
To GET OUT OF THE GUIDE:
Press OK to exit the Guide and tune to the highlighted channel,
Press GUIDE to exit the Guide and tune to the channel displayed
in the View window,
Press CLEAR to exit the Guide and go to the last channel you were
watching,
STEP7:PROGRAM THE TV
Proceed to the next section, Interactive Setup. The interactive setup
routine walks you through the steps needed to fully configure the TV.
The first steps ask you to select your preferred language for the menu
system and to begin the auto channel search, which puts available
cable TV or antenna signals into the TV's memory.
Projection TV Only.
If the picture appears to have a double or
triple image or if you notice rings or halos
around objects, you may have to adjust
the color convergence. Details can be
found under the Screen menu heading in
the Features and Menus section of this
manual.
10
INTERACTIVE SETUP
THERE'S AN ON SCREEN SETUP ROUTINE
The interactive setup routine takes you through the steps
needed to configure theTV:
Select a menu language
Search tor available channels
Set up the GUIDE Plus+ Gold system
Set the time
Set theVCR1 channel
Set theVCR2 channel
Set the DVD channel
Set the SAT/CABLE channel
Make the channel list and labels
1
2
SETUP AND
CONNECTIONS
¥
INTERACTIVE SETUP
¥
3 USING THE REMOTE
4
¥
FEATURES AND MENUS
¥
5 REFERENCE
11
INTERACTIVE SETUP
USING POINT AND SELECT
You only need to know one rule when using the remote to access on-
screen menus and control panels: point and select. The point and
select method has two steps.
1. Point to a menu item using the MOVE arrows on the remote.
To point up or down, press the up or down arrows. To point left
or right, press the left or right arrows.
2. Select a menu item by pressing MENU or OK.
Selecting an item tells the TV's menu system to go ahead and
make the change or go to a place you have indicated.
ENTERING SETUP
The first screen of the Interactive Setup appears automatically when
you turn on your TV for the first time or after a power outage.
1. Press MENU to begin setup or CLEAR to exit.
Point and Select buttons
You can also access the Interactive Setup through the Main menu:
1. Press MENU to bring up the Main menu.
2,
Point to Setupand press MENU or OK. The first Setup screen
comes up, asking you to confirm that you want to begin.
You can also select a menu item by
entering the item number with the
number buttons on the remote.
Press CLEAR at any time to remove all
displays from the screen and return to TV
viewing.
Many VCR user manuals refer to a
PROGRAM button. The MENU button on
this remote works as a PROGRAM button
in VCR mode. Other manuals may refer
to a SELECT button. The OK button on
this remote works as a SELECT button.
12
INTERACTIVE SETUP
3. Point to Begin setup now and press MENU or OK.
SELECT A LANGUAGE
The first part of the setup routine asks you to select your preferred
language for the menu system.
1. Point to your preferred language for the menu system.
2. Press MENU or OK to select that language.
AUTO CHANNEL SEARCH
The next part of the setup routine asks you if you want the TV to search
automatically for all channels available through your antenna or cable
TV system. This is sometimes called "autoprogramming."
1,
Press MENU or OK to tell the TV to begin searching for channels.
The display gives you a progress report and tells you when it has
finished.
2, Press MENU or OK to continue.
If you skip Auto Channel Search now,
you can access it later through the
Channel menu. You can also put
channels in memory, manually using List
& Labels. See Features and Menus for
more details.
13
INTERACTIVE SETUP
THEGUIDE Plus+ GOLD SYSTEM
The next step lets you set up the GUIDE Plus+ Gold system to display your local
program listings, and control your cable box and VCR.
You can either press MENU or OK to bring up the GUIDE Plus+ Gold initial
menu or point to Skip this Step to move to the next step in the Interactive Setup.
You can set up the GUIDE
Plus+ Gold system during
the Interactive Setup. You
can also access the GUIDE
Plus+ menus by pressing
menu on the remote, and
selecting GUIDE Plus+
Menu.
SETTING UP THE GUIDE Plus+ GOLD SYSTEM
Tocomplete GUIDE Plus+ Gold setup, the GUIDE Plus+ Gold IR controllers must be connected to your cable
box and VCR if you have them. Refer to the Setup and Connections section for additional information.
Select your Country and enter your ZIP or
Postal code.
The next series of screens asks you about
your cable TV setup. If you have a cable
box, you need to set the GUIDE Plus+
Gold system to control it. Otherwise, it
may not be able to locate and download
program information.
Tune your cable box to Channel 2 and
then select the brand of your cable box
from the choices available. The system
then searches for the correct code to
control your cable box. When your cable
box switches to channel 9, it has located
the correct code.
14
INTERACTIVE SETUP
Select Yes if the cable box changed to channel 9, or No if it did not, If you select No, the system will try another code.
If the GUIDE Plus+ Gold system cannot recognize either your cable box or VCR after several tries, a screen stating
"Cable Box (VCR) test failed..."Please consult your manual and try again" appears. You have a choice to either TryAg_in
or Skip Cable Box Setup. If you get this message, you should also:
Double check the brand of your cable box or VCR, and try entering it again.
Check to make sure the IR controllers are positioned correctly.
If you choose to skip the cable box (or VCR) setup some features of the guide may not be available until you successfully
complete this procedure.
Once the correct model of cable box (or
VCR) has been identified, you need to set
the cable box's output channel. Enter the
channel you use to view channels
through your cable box--usually 3 or 4.
Consult your cable box's instruction book
or your cable company if you are not
sure. Choose Oto use VIDEO INPUT.
Select YES if you have a VCR, or NO if not.
Answering NO automatically skips forward
to the end of GUIDE Plus+ Gold setup.)
Tune your VCR to channel 2 and turn it off.
Enter the brand of your VCR.
When the GUIDE Plus+ Gold system
correctly identifies the correct code for
your VCR, the VCR's tuner changes to
channel 9.
Select YES if the VCR automatically
changed to channel 9, or NO if it did not.
If you select NO, the system will try
another code.
The last screen that comes up after you've successfully finished the
GUIDE Plus+ Gold setup gives you an opportunity to view a demo. If you
don't want to view the demo, highlight EXIT and press OK.
Remember:
Leave your cable box turned ON to download program information.
Leave your VCR turned OFF to record programs and download
program information.
15
INTERACTIVE SETUP
SETTING THETIME
The next step in the Interactive Setup lets you set the time of day. If
your GUIDE Plus+ system has not completed its first download, you
need to set the time. Once the system has completed its first
download, it sets the time for you automatically and you may not see
this screen.
1. Press MENU or OK to bring up the SET TIME control panel.
2. Use the left and right arrows to point to the hour and minutes
spaces. Use the digits to enter the numbers and the up and down
arrows to change from AM to PM.
3. Press MENU or OK to continue.
SETTING THE VCRI CHANNEL (AUTO TUNING)
The next stepletsyou settheVCRI channel.When you settheVCRI
channel, you'retellingthe TV what channel to tune to when you press
the VCRI buttonon the remote.Thisiscalledauto tuning.
Indicatewhich inputyou used to connect the VCR. Ifyou don'thave
a VCRI component connected tothe TV, skipthisstepor selectNot
Connected from the VCR1 Channel choice list. (For more, see Auto
Tuning in the Features anti Menus section.)
16
INTERACTIVE SETUP
1. Press MENU or OK to bring up the VCR1 choice list.
2.
Point to the choice that matches the way you have your VCR
connected to the TV. If you used audio/video cables, choose the
video input you connected the cables to.
3, Press MENU or OK to continue.
SETTING THEVCR2 CHANNEL (AUTO TUNING)
The nextstep letsyou settheVCR2 channel. When you settheVCR2
channel, you're telling the TV what channel to tune to when you press
the VCR2 button on the remote.
Indicate which input you used to connect a second VCR. If you don't
have a second VCR component connected to the TV, skip this step or
select Not Connectedfrom the VCR2 Channel choice list. (For more,
see Auto Tuning in the Features and Menus section.)
1. Press MENU or OK to bring up the VCR2 choice list.
17
INTERACTIVE SETUP
2. Point to the choice that matches the way you have your second
VCR connected to the TV, If you used audio/video cables, choose
the video input you connected the cables to.
3. Press MENU or OK to continue,
SETTING THE DVD CHANNEL (AUTO TUNING)
The next step lets you set the DVD channel. When you set the DVD
channel, you're telling the TV what channel to tune to when you press
the DVD button on the remote,
Indicate which input you used to connect a DVD player. If you don't
have a DVD player connected to the TV, skip this step or select Not
Connected from the DVD Channel choice list. (For more, see Auto
Tuning in the Features and Menus section.)
1. Press MENU or OK to bring up the DVD choice list.
18
Loading...