Pro-safe GP477R-EG41-24VP User Manual

WARNING

• When connecting a power cable to the GP unit, be sure the cable has been unplugged

from the power outlet, so that you would not get an electric shock.

• High voltage runs in the GP unit, so if you take unit apart, there is a danger of getting an

electric shock. Do not take the unit apart.

• Do not use power beyond the specified voltage range. If you do, it may cause a fire or

an electric shock.

• Do not reconstruct the GP unit. It may cause a fire or an electric shock.

• Do not use the GP in an environment with flammable gas in the surrounding atmo-

sphere. It may cause explosion.

• GP use a lithium battery for backing up its internal clock data. If the battery is incor-

rectly replaced, the battery may explode. To avoid the danger, do not replace the
battery yourself. When the battery needs a replacement, please consult with your
local GP distributor.

• Do not use touch panel switches in life-related or important disaster prevention situ-

ations. For safety related switches, such as an emergency switch. use a separate me­chanical switch.

• Please design your system so that the machine will not malfunction by a communica-

tion fault between the GP and its host controller. If not, there could be a danger of
injuring a person or damaging materials.

To Prevent From Damage:

• Do not hit the touch panel with a hard or heavy object, or press the touch panel with too

much force, for it may cause irreparable damage.

• Do not use GP in an environment where the surrounding temperature exceeds the

specification range, for it may damage the unit.

• Please ensure that liquids or metal do not enter the GP unit, for it may cause malfunc-

tion or a short.

• Please avoid using the unit in areas where sudden, large changes in temperature may

occur. These changes can cause condensation to form inside the unit, possibly caus­ing an accident.

• To prevent from heat building up inside the GP, please do not install GP where its

ventilation holes may be blocked, or where heat cannot escape. Also, please avoid
using or storing the GP in an extremely hot place.

• Do not operate the GP in areas with temperatures and humidity in express of those

levels specified to prevent the GP’s touch panel from becoming warped or bent.

• Please avoid using or storing the GP under direct sunlight or in a dusty environment.

• This unit is a delicate equipment, so please avoid using or storing the GP unit in an

environment where it can receive strong impact or vibration.

• Please avoid using or storing GP where vaporized chemicals or chemicals can stick to

it.

• Do not use paint thinner or organic solvents to clean the GP unit or display.

• Because unforeseen circumstances may befall your GP unit, be sure to back up your

screen data.

• After turning this unit OFF, be sure to wait a few seconds before turning ON again. If

the unit is started within a few seconds, it may not start up correctly.

UL/cUL(CSA) Approval

The GP477R-EG41-24VP are UL/cUL(CSA) recognized products.
(UL file No. E182139)

GP477R-EG41-24VP conforms as a component to the following standards:

EUL508

•

Industrial Control Equipment
UL1604

•

Electrical Equipment for Use in Class I and II Division 2 and Class III Hazardous
(Classified) Locations

CAN/CSA-C22.2, Nos.142,and 213-M1987

•

Standard for Safety of Information Technology Equipment, including
Electrical Business Equipment

GP477R-EG41-24VP (UL Registration Model : 2780027-01)

• The GP should be installed in the front face of a metal panel.

• If the GP is installed so as to cool itself naturally, be sure to install it in a verti-

cal panel. Also, be sure that the GP is mounted at least 100mm away from adja­cent structures and other equipment, otherwise, the heat generated by the GP's
internal components may become higher than that allowed by UL standard re-

quirements.

• The terminal block’s earth terminal

is a protective earth terminal. Be sure to

connect this terminal in accordance with UL standards.

Installation and operation instructions are provided with each GP. These installation
instructions contain the following statements.

1. Power, input and output (I/O) wiring must all be in accordance with Class I, Divi­sion 2 wiring methods, Article 501-4 (b) of the National Electrical Code, NFPA
70, or as specified in Section 18-152 of the Canadian Electrical Code for units
installed within Canada, and in accordance with that location's authority.

2. Suitable for use in Class I, Division2, GroupsA, B, C and D hazardous location, or
nonhazardous locations only.

3. WARNING: Explosion hazard-substitution of components may impair suitability
for Class I, Division2.

4. WARNING: Explosion hazard-do not disconnect equipment unless power has been
switched off or the area is known to be nonhazardous.

5. WARNING: Explosion hazard-when in hazardous locations, turn off power before
replacing or wiring modules.

CE Marking

GP477R-EG41-24VP is CE marked , EMC compliant products.These units also
conform to EN55011 class A , EN50082-2 directives.

Package Contents

The following items are included in the package. Before using, please ensure every­thing is there.

GP unit
(GP477R-EG41-24VP)

Handling guide 1 sheet
(this sheet)

Handling

Guide

Installation fasteners (4 pcs)

This unit has been carefully packed, with special attention to quality. However, should
you find anything damaged or missing, please contact your local GP distributor im­mediately.

Extra-Cost Options

Manual
GP477R/577R Series
User’s Manual

Digital

GP477R/577R Series

User's Manual

Cables
Adapters
Screen editor software

are optionally available.

For more information, see Digital's cata­logues.