Page 1
Made in China
Conforms to safety requirements of ASTM, CPSIA and FCC.
©2015 Rooftop Brands™ All rights reserved
Tel: + (1) 949-566-9573 • www.propelrc.com
FCC Part 15 B Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
CHOKING HAZARD
-
Small parts.
Not suitable for children under 3 years.
WARNING!
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect the Falcon™ from charger immediately after the
Falcon™ is fully charged. Please refer to enclosed safety instructions.
INSTRUCTION BOOKLET
Colors and styles may slightly vary.
PACKAGE CONTAINS:
2.4G Wireless Controller Instruction ManualSpare Parts USB Card Reader
Battery Charger
Falcon™ Drone
FALCON
™
Full Sized High Performance Camera Drone
CARE AND MAINTENANCE
• Always remove the batteries from the wireless remote control when it is not being used for an
extended period of time.
• To clean, gently wipe the remote control and Falcon™ with a clean damp cloth.
• Keep the toy away from direct heat or sunlight.
• Do not submerge the toy into water. This can damage the unit beyond repair.
• Parental guidance recommended when installing or replacing the batteries.
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Page 2
C
A B
6 1.5 volt “AA” Alkaline Batteries
D
Battery Charger
Li-Po (lithium polymer) Battery
AC Adapter
CHARGER POWER
1 2
TABLE OF CONTENTS
Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Charging Your Falcon™ Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Falcon™ Quadrocopter Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Remote Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Attaching The Landing Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Flight Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Syncing Your Falcon™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Flying Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recognizing The Front & Back Of The Falcon™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Channel Flight Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Adjusting Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Level Surface Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Flight Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Flight Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Performing A 360º Stunt Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attaching The Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operating The Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Activating Orientation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Thank you for purchasing the Falcon™ 2.4 Ghz Quadrocopter. Please read this instruction booklet as it
contains valuable information on how to properly fly and care for your Falcon™ Drone.
FEATURES
• 4 axis high-speed aircraft for incredible maneuvers including 360º aerial stunts!
• Built-in 6 axis gyro chip for extremely stable flight and maneuverability even in windy conditions.
• Includes wide-angle 5 mega pixel 30 FPS camera on precision stabilizer.
• 2.4 Ghz, remote allows flight range up to 500 feet and multiple player use.
REMOTE CONTROL BATTERY INSTALLATION
1. Remove the battery cover from the back of the controller as shown in diagram A.
2. Install 6 “AA” fresh alkaline batteries into the controller as shown in diagram B. Make sure to install
batteries to their correct polarity. Do not mix old and new batteries or battery types.
3. Replace the battery cover.
CHARGING YOUR FALCON™ BATTERY
1. Turn the Falcon™ over and carefully remove the battery cover screw with Phillip head screw driver
(provided) slide battery cover towards the rear of the Falcon™, and remove battery (see diagram C).
2. Connect the battery’s charging connector to the battery charger and plug into a standard wall socket.
CAUTION: improper connection may damage the Falcon™.
3. The LED battery charger light will shine green when connected properly to the AC adapter.
The indicator LED will glow red while the unit is charging. Remove promptly after the red LED turns off,
indicating the charge is complete(see diagram D).
4. A full charge will allow for about 7 minutes of flight time depending on environment and user input.
IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!
Page 3
Propeller Guard
Propeller Guard
Propeller Blade
Li-Poly Battery Compartment
FALCON™ QUADROCOPTER DIAGRAM
FALCON™ REMOTE DIAGRAM
Landing Gear
Speed Setting
Up/Down Trim
Throttle Lever
& Rotation Control
Rotate Left/Right
Trim
Light
Orientation Mode
Photo
VideoPower Switch Channel &
Power % Indicator
Power Indicator
Antenna
360º Flip Button
Direction Lever
Forward/Backward &
Bank Left/Right
Forward/Backward
Trim
Bank Right/Left
Trim
Notch
F
3 4
FLIGHT PREPARATION
• Verify that there are 6 “AA” batteries inside the remote control unit and the Falcon™ has been
fully charged.
• Make sure your Falcon™ and controller are both turned on.
• Make sure to be in a large space with an open radius of at least 50 feet.
• Make sure the empty space has no obstacles. Set your Falcon™ on a clean flat surface before take-off.
DO NOT ATTEMPT TO FLY YOUR FALCON™ IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING
OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.
SYNCING YOUR FALCON™
Important! When syncing your Falcon™ quadrocopter with the controller always make sure that the
quadrocopter is on a flat level surface and that your digital trim settings are in the center position.
This insures that the 6 Axis gyro is properly programmed to mimic your trim settings.
Your Falcon™ utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by
side in the same wireless range with no interference.
Syncing your aircraft:
1. Before starting, make sure that the power on your controller is in the OFF position and the Falcon™
wire leads are not connected. Make sure that there are no other 2.4G devices in the area as well .
2. Connect the battery wire lead to the Falcon™ lead and replace Battery cover (see diagram C) and turn
the Falcon over and set it down on a flat surface (see diagram F). The LED indicator lights of the Falcon™
will begin to flash.
3. Turn ON the remote, the flashing LED lights should change to solid, and you should hear 2 beeps push
the throttle on the left all the way forward and then slowly pull the throttle all the way back until you hear
a beep. Your controller and the Falcon™ should now be successfully synced , if not, repeat above steps.
FLYING TIPS
• It is recommended that you operate the Falcon™ in a wide space. The ideal space should have a
200 foot radius.
• Parental guidance or adult supervision is suggested at all times.
• If you are flying the Falcon™ with others, make sure all spectators are behind you.
• For best performance, it is recommended that you operate the Falcon™ in zero wind conditions.
Heavy wind can greatly affect the performance of the aircraft or cause injury.
DO NOT FLY YOUR FALCON™ IN FOUL WEATHER!
WARNING
ATTACHING THE LANDING GEAR
• Attach the right and left landing gear legs on the underside of the
Falcon™ with the 4 screws provided (see diagram E) .
• Please note the right side landing gear has a notch to
accommodate the camera connection.
Page 4
F
J
K
L
M
N
G
H
I
FRONT
E
FRONT
REAR
5 6
Forward/Backward Trim
• If your Falcon™ drifts forward, push and
release the BACKWARD TRIM button back
repeatedly until the motion stops and proper
flight is maintained (see diagram J).
• If your Falcon™ drifts backwards, push and
release the FORWARD TRIM button forward in
the same manner until the problem is resolved.
Bank Right/Left Trim
• If your Falcon™ drifts left, push and release
the RIGHT TRIM button back repeatedly until
the motion stops and proper flight is
maintained (see diagram K).
• If your Falcon™ drifts right, push and release
the LEFT TRIM button in the same manner until
the problem is resolved.
Spin Right/Left Trim
• If your Falcon™ spins left, push and release
the RIGHT SPIN TRIM button back repeatedly
until the motion stops and proper flight is
maintained (see diagram L).
• If your Falcon™ spins right, push and release
the LEFT SPIN TRIM button in the same manner
until the problem is resolved (see diagram M).
LEVEL SURFACE CALIBRATION
If the aircraft becomes unstable during the
course of flying, you may need to re stabilize the
internal gyros.
To do this place the Falcon™ on a level surface,
set the speed setting to 100% first, then pull
both of the control levers on the remote down
and to the left (approximately 45º) at the same
time. The LEDs on the Falcon™ will flash quickly
and then remain solid, this indicates your aircraft
has been stabilized (see diagram N).
FLYING ENVIRONMENT
When flying the Falcon™ do so in warm sunny weather with no wind or rain.
WARNING: Do not fly in extreme temperatures or windy conditions as this may affect the performance of
your Falcon™ and cause damage or injury.
4 CHANNEL FLIGHT CONTROL
Below is a list of basic flight functions for your long-range remote control Falcon™. While learning to fly
your Falcon™ it is best to start with a large space until you get used to the basic controls. As you master
flying your Falcon™ you can move to more advanced maneuvering techniques. Practice makes perfect!
When you have these basic steps down you can move to the next level.
Move the left Throttle stick up to increase the
propeller speed and the Falcon™ will accelerate
and ascend.
Move the left Throttle stick down to decrease
the propeller speed and the Falcon™ will
decelerate and descend (see diagram F).
While in the air, move the left Throttle stick left
and the Falcon™ will rotate left.
Move the left Throttle stick right and the
Falcon™ will rotate right (see diagram G).
While in the air, move the right Direction Stick
up and the Falcon™ will move forward.
Move the right Direction Control down and the
Falcon™ will move backward (see diagram H).
While in the air, move the right Direction Control
left and the Falcon™ will bank to the left.
Move the right Direction Control right and the
Falcon™ will bank to the right (see diagram I).
RECOGNIZING THE FRONT & BACK OF THE FALCON™
Even though the Falcon™ has four rotors there is still a front or "forward" facing direction and "back" or
backwards facing direction. The front of the Quadrocopter displays BLUE LED lights and the back of the
Quadrocopter displays RED LED lights when activated (see diagram E).
ADJUSTING TRIM
From time to time you may have to adjust the TRIM buttons to ensure the Falcon™ will hover in mid-air
and respond accurately to your commands.
Page 5
Fixed-point landing Square Pattern Maneuver Cross Pattern Maneuver
Flip Forward
Flip Right Flip Left
Flip Backward
P Q
O1
O3
O2
Stabilizer
Camera
7 8
FLIGHT PRACTICE
To master flying your aircraft try practicing the excersizes shown below. Start with simple vertical takeoffs,
landings, and left/right turning and rotating. Once those are mastered move on to square and cross
maneuvers. Good luck and have fun!
PERFORMING 360º STUNT FLIPS
After you have mastered flying the Falcon™ you are ready to try flips. Once the Falcon™ is hovering at least
3 meters (about 10 feet) off the ground click the 360º Flip Button (see diagram O1) and push the right lever
forward slightly and let go. The Falcon™ will instantly perform a forward flip. To perform a backwards or
side flip click the 360º Flip Button and push the right lever in the direction you wish to flip just as you did
for the forward flip (see diagram O2 & O3).
PROBLEM POSSIBLE REASON SOLUTION
1. Power switched off 1. Switch the ON/OFF switch to ON
No Power 2. Polarity is reversed 2. Make sure all batteries are installed
correctly (see diagram B)
3. Batteries may be dead 3. Replace batteries
1. Remote is switched off 1. Switch the ON/OFF switch to ON
Remote Not 2. Falcon™ battery is not connected 2. Switch the ON/OFF switch to ON
Responding 3. Too windy 3. Windy conditions severely impair the
operation of the Falcon™
4. The remote is not synced 4. Re-sync the remote
Aircraft Won’t 1. Rotor speed too slow 1. Push throttle lever forward
lift off 2. Aircraft not fully charged 2. Recharge your Falcon™
Aircraft
Descends 1. Moving the throttle too quickly 1. Control the throttle slower and
Too Fast smoother
Aircraft Not 1. Gyroscopes not functioning 1. Turn of the Falcon™ and
Responding Reset the Gyros (see diagram L)
Loss of
Falcon™ 1. Aircraft is out of range of remote 1. Keep the aircraft within a 500
Control Feet radius of the remote
TROUBLESHOOTING YOUR FALCON™
ATTACHING THE CAMERA
You have the option of attaching the included wide-angle 5 mega pixel 30 FPS camera with precision
stabilizer to your Falcon™ quadrocopter.
1. Install the stabilizer to the battery cover panel on the under side of the Falcon™ with the 4
screws provided (see diagram P).
2. Snap the camera to the stabilizer and connect the camera lead to the Falcon™ base (see diagram Q).
Page 6
FRONT
REAR
B A
A B
U
R S T
V
Photo
Video
9 10
FALCON™ WARNING:
The Falcon™ is designed for OUTDOOR use. Falcon™ blades revolve at high speeds and can cause damage to
the user, spectators and animals. Stand away from the Falcon™ to reduce the risk of getting into the flight
path. Warn spectators that you will be flying your Falcon™ so that they are aware of its position. Before
flight, inspect the rotor blades to make certain that the blades are securely fastened to the Falcon™.
WARNING!
• Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.
• Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the
ON position.
• Turn off the transmitter and Falcon™ power switches when not in use.
• The included charger is built specifically for the Falcon™ Li-Poly battery. Do not use it to charge any
other battery.
• New alkaline batteries are recommended for maximum performance.
• Parental supervision recommended when flying Falcon™.
BATTERY WARNINGS
RECHARGEABLE BATTERY:
This Falcon™ uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery
properly according to local disposal requirements.
CONTROLLER BATTERIES:
Remote control requires 6 “AA” batteries (not included). Please read the important battery safety warning
below.
• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).
• Do not mix old and new batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the item before being charged (if removable).
• Rechargeable batteries are only to be charged under adult supervision.
• Exhausted batteries should be removed immediately and must be recycled or disposed of properly
according to state or local government ordinances and regulations.
• The supply terminals are not to be short-circuited.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).
• Do not dispose batteries in a fire - batteries may leak or explode.
REPLACING THE PROPELLER BLADES
Your Falcon™ propeller system is a precision instrument that may need repair or replacement from time
to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your
Falcon™ propellers.
1. Falcon™ have four blades, two on the front, and two on the back.
Always disconnect the battery before replacing the propeller blades.
Please note that the blades and the Falcon™ are labeled with an embossed A or B (see diagram P ).
2. When replacing the propeller blades, remove the small screw and gently lift the blade from the
rotor shaft.
3. Replace the damaged blade with the correct blade. Make sure to match the indication letter on the
blade with the letter on the aircraft as shown in diagram U.
OPERATING THE CAMERA
You can take in-flight photos or video with your Falcon™ on board camera.
1. Once the camera is attached and connected insert the Micro SD card into the camera body (see diagram R).
2. To take still photos press the photo button on the remote (see diagram S).
3. To take video footage press the video button on the remote to record and again to stop (see diagram S).
4. To retrieve your photos and footage remove the card once the Falcon™ has landed safely and insert the
card into the USB card reader proved and connect to your computer’s USB port and download the
photos and video footage (see diagram T).
ACTIVATING ORIENTATION MODE
You can maintain orientation of your Falcon™ during flight.
1. Once the Falcon™ is activated press the orientation mode button (see diagram V) to activate the
internal compass.
2. The flying orientation is now locked to match the direction control lever.
Loading...