ProofVision PV10-PS-FR, PV10, PV10-B-FR, PV10-BS-FR, PV10P Installation Instructions

PV10 / PV10P

This product is suitable for use in
bathrooms for Oral-B and Braun electric
toothbrushes only.

Please check with manufacturer’s
instructions for suitability with toothbrush
model.

This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.

Children shall not play with the
appliance.

Cleaning and user maintenance shall
not be made by children without
supervision.

SAFETY INSTRUCTIONS

All installation work should be undertaken
by a competent person in accordance
with the current edition of the IEE Wiring
Regulations (BS 7671) and appropriate
statutory regulations. In the Republic of
Ireland the installation must be in
accordance with the ETCI National Rules
for Electrical Installations -ET101.

IF IN DOUBT, CONSULT A QUALIFIED
ELECTRICIAN

Before starting any electrical work,
ensure that the electricity supply is
SWITCHED OFF at the mains.

For additional safety, remove the fuse or
switch off the circuit breaker at the fuse
box or consumer unit.

IMPORTANT NOTICE – WIRING COLOUR
CHANGES

As from 1st April 2004 new installations in
the UK could be wired using the new EU
Harmonised colours for the supply
conductors of twin and earth cable:

New Colours

Brown = Live
Blue = Neutral
Green/Yellow = Earth

Old Colours

Red = Live
Black = Neutral
The old colours will cease to be used
from 1st April 2006.

Flexible cable colours remain
unchanged:
Brown = Live
Blue = Neutral

In-Wall Electric

Toothbrush Charger

Compatible with all Oral B and Braun

rechargeable toothbrushes

[phone] | [e-mail] | www.proofvision.co.uk |

Eire conductor colours for twin and earth
cable and flexible cable:
Brown = Live
Blue = Neutral

INSTALLATION AND WIRING INSTRUCTIONS

This toothbrush charger unit is suitable for
mounting with a 47mm deep 2 gang
flush metal box.

NOTE: check orientation of box when
fitting this unit on a surface pattress box.

For the best mounting results and visual
appearance, it is recommended that
prior to installation, the mounting surface
between the accessory front plate is first
prepared to ensure that it is flat and all
high spots have been removed.

1. Remove product and screws
supplied from the packaging

2. Feed incoming supply cable through
appropriate knockout entry in back
box. Ensure a protective cable
grommet is fitted when using a flush
metal box.

3. Remove suitable length of outer
sheath from the supply cable.
Remove 10mm from the live and
neutral inner insulation to expose the
conductor ends.

4. Insert Neutral conductor into the
charger supply unit terminal into
either of the 2 available terminals
available (mains are both red so are
interchangeable)

5. Insert live conductor into the charger
supply unit into the other available
terminal.

6. Before connecting the protective
earth conductor, ensure that all bare
earth conductors are sleeved with a
length of Green/ Yellow sleeving (not
supplied)

7. Insert sleeved earth conductor into
terminal marked with the Earth
symbol.

8. Ensure that an additional sleeved
earth conductor is also fitted
between the charger unit earth
terminal and the earth terminal fitted
in the flush metal box.

9. Ensure all terminal screws are tight.

10. Fit the toothbrush charging unit onto
the mounting box, taking care not to
trap any cables.

11. Secure unit using the fixing screws.

12. Ensure that the plastic frame is
correctly fitted and then fit the front
plate in place.

13. Refit the supply fuse (if removed)
and switch on mains supply.

14. Parts that are required to be fixed
should be fixed so that they cannot
fall into water.

DISPOSAL OF THE TOOTHBRUSH CHARGER

This symbol on the product or on its
packaging indicates that this product
shall not be treated as household waste.
Instead it shall be handed over to the
applicable collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is
disposed of correctly, you will help
prevent potential negative
consequences for the environment and
human health, which could otherwise be
caused by inappropriate waste handling
of this product. The recycling of materials
will help to conserve natural resources.

89mm

161mm

39mm

52mm

CUSTOMER CARE CENTRE:

[e-mail]

[phone]

ProofVision

Unit 1, Avad House,

Belvue Road, Northolt, Middx

UB5 5HY

[phone] | [e-mail] | www.proofvision.co.uk |