Page 1
SATHUNTER+
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com
QUICK REFERENCE GUIDE
FRONT VIEW
1
2
3
1
RF signal input
2
Detect
3
Identify
USB connector
4
5
External power input 12 V
Adjust
6
4
Trademark of the
DVB - Digital Video
Broadcasting Project
5
6
SCREEN ICONS REFERENCE
USB
18/13/OFF
S S2 DS
S S2 DS
Manual Power Off.
USB connected to the PC.
Battery level
22 kHz signal activated.
Charging battery.
LNB power supply (13 V, 18 V or OFF).
The DVB-S, DVB-S2 or DSS has not been synchronized.
The DVB-S, DVB-S2 or DSS has been synchronized.
SATHUNTER+
Page 2
SATHUNTER+
When using the SATHUNTER+, it may appear on the display some messages and icons, depending
on the status or event is taking place. These messages and icons are detailed below:
QUICK REFERENCE GUIDE
“LOW BATTERY”
“VERY LOW BATTERY”
“LNB SHORT CIRCUIT”
“LNB OVER CURRENT”
“MANUAL POWER OFF”
“AUTO POWER OFF”
“BATTERY MODE”
“UPDATE MODE”
“NETWORK NOT FOUND”
“SERVICES NOT FOUND”
“LNB NOT DETECTED”
“FULL BATTERY”
“MPEG-2 NOT DETECTED”
“LOADING NETWORK”
“LOADING SERVICES”
“HIGH TEMPERATURE”
OPERATION
The equipment will be switched off automatically.
The LNB can be short circuit.
The LNB has a high consumption.
The instrument has to be switched off by hand.
The instrument will switched off after five minutes of inactivity.
-
-
-
Power level is below the minimum necessary to detect a LNB (this value can
10%)
be adjusted by software, usualy .
It is not detecting the Transport Stream signal MPEG-2.
-
The running temperature is too high. The equipment must be switched off for
a while. If the problem persist, contact with the technical support.
Turn on the SATHUNTER+ pressing , or for two seconds. If you press or
for more than five seconds, it starts in manual power off mode.
DETECTION
Plug the SATHUNTER+ to the antenna socket and turn the antenna until the SATHUNTER+ shows
the maximum power on the display.
RF
1) DETECT
MA X POWER R ATE: 41 %
PO WER RAT E: 40 %
18
+
LNB Voltage
Maximum measured
power
Current power
Page 3
SATHUNTER+
IDENTIFICATION
Press and wait until locking the signal. The display will show the parameters of the
test point (name and frequency), the channel tuned and its services. To change to
another stored channel press again.
QUICK REFERENCE GUIDE
Test Point Name
and frequency
Turned channel name
Services
PRESS
PRESS
IDENTIFY.
IDENTIFY.
Sequential number of the test point
RF
2) IDENTIFY 13 S2
TP 64 FR : 13 96.0MH z
13 E Sk y
NE T:
SE RV I CE L IS T: 3/ 8
Ne xt H D
SK Y Ci nema HD
Na tionalGeo H D
Locked signal Standard
TP0 4
++
PRESS IDENTIFY TO MOVE
PRESS IDENTIFY TO MOVE
TO THE NEXT STORED
TO THE NEXT STORED
RF
TEST POINT.
TEST POINT.
Test point
frequency
2) IDENTIFY 13 S2
TP 65 FR :
NE T:
4E8_EU
SE RV I CE L IS T: 3/ 4
TVE Internacional
RTL Television
TV5 Monde Europe
TP0 5
1799.0
MH z
++
Page 4
SATHUNTER+
ADJUST
Press to perform fine-tuning. Check that every user's access point in the installation
is meeting the criteria established by current regulations. To measure another stored
channel, press again until finding the channel you are looking for. In case not
locking the signal, it shows the Signal to Noise Ratio (SNR).
Test Point Name
3) ADJUST
TP 65 FR:1799.0 MHz
PO WER: 54.7dBuV
ME R:13.9dB LM : 9.0 dB
0
CB ER:
PRESS
PRESS
ADJUST
ADJUST
VB ER:
RF
QUICK REFERENCE GUIDE
Sequential number of the test point.
Locked signal
TP0 5
13 S 2
1. 2E-5
<1 .0E-8
++
15
PRESS ADJUST FOR
PRESS ADJUST FOR
Test point frequency
THE NEXT TEST
THE NEXT TEST
POINT
POINT
Turn off the SATHUNTER+ by pressing or for three seconds.
CONFIGURATION
At the DETECTION screen, press and hold until appears the configuration menu.
AD JUST
)S ETUP
1) CAN CEL 2 )O PTI ON 3) SEL EC T
TP 0 HI30 FR:1779.4M Hz
ST ART SPECTRUM
PO WER: 54.7dBuV
SE LECT MEASURE MER
LM : 9.0dB MER : 13. 9dB
SO UND CONTROL BEEP
0
BA CKLIGHT MODE AUTO
CB ER:
CO NTRAST LCD
VB ER:
CO N FI RM & E XI T
TP0 4
13 ~ S
18 V
1. 2E-5
<1 .0E-8
10
++
Exits the configuration menu
without saving changes.
Scrolls along the menu options.
Changes the parameter / Accepts.
v1.0
Start Spectrum: It starts the Spectrum Analyser.
Select Measure: Select measurement you want larger on the screen.
Confirm & Exit: It applies and saves the changes made and exits the configuration menu.
27-06-2016 (0 DG0078)
Loading...