Page 1
®
®
®
®
SPLIT LID TABLE TOP
®
TWO SIDED GRILL
MODEL
GR14SPTK-CN
(9D-GR14SPTK-CN)
Installation and
Operation
Instructions
2M-Z11270 Rev. E 9/30/11
1
Page 2
2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
Star reserves the right to change speci cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
regulations, the speci cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
speci cations. By using the information provided, the user assumes all risks in
connection with such use.
MAINTENANCE AND REPAIRS
Contact your local authorized service agent for service or required maintenance. Please record
the model number, serial number, voltage and purchase date in the area below and have it
ready when you call to ensure a faster service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
Service Related Issues Contact:
Middleby China Corporation
#98 ShengGao Road
Jiu Fu Development Zone
Jiuting Town, Song Jiang District
Shanghai, 201615 China
Phone: 011-8621-6769-0808
Fax: 011-8621-6762-7640
WARNING
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or similarly qualied persons in
order to avoid a hazard.
2
Page 3
GENERAL SPECIFICATIONS
B
C
A
D
IL1378-CH
半开位置
FIRST OPEN POSITION
全开位置
FULL OPEN POSITION
半开位置
(11.77厘米)
(37.92厘米)
(54.80 厘米)
53.34厘米
(52.59厘米)
(32.07厘米)
(A) Width
Inches
Model No Grill Surface
(cm)
GR14SPTK-CN Aluminum 16" (40.6)
(B) Depth
Inches
(cm)
23 1/8"
(58.7)
(C)
Closed
Inches (cm)
14 1/4"
(36.3)
(D) Open
Inches
(cm) Voltage Wattage Amps
31 5/8"
(80.3)
240 2,300 9.6 CH2-16P 81 (37.8) 68 (30.9)
3
NEMA
Plug
Approximate Weight
Shipping
lbs. (kg)
Installed
lbs. (kg)
Page 4
CAUTION
GENERAL INSTALLATION DATA
This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for
use directly by the general public in food service locations.
Before using your new equipment, read and understand all the instructions & labels associated with the unit prior to putting it into operation. Make sure all people associated with its
use understand the units operation & safety before they use the unit.
All shipping containers should be checked for freight damage both visible and concealed.
This unit has been tested and carefully packaged to insure delivery of your unit in perfect
condition. If equipment is received in damaged condition, either apparent or concealed, a
claim must be made with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within
15 days. Be certain to retain all contents plus external and internal packaging materials for
inspection. The carrier will make an inspection and will supply necessary claim forms.
INSTALLATION
1. This two sided grill is equipped for the voltage shown on the nameplate. It will operate
on alternating current only, however the specied voltage must be applied.
2. 120 volt units must be plugged into an individual branch circuit 120 VAC line with a 20
Amp receptacle. 230-240 volt units must be plugged into a 230 VAC line with a 15 Amp
receptacle.
WARNING
DO NOT CONNECT THE UNIT TO ANY TYPE OF VOLTAGE OTHER THAN THAT
ON THE NAMEPLATE. DOING SO WILL DAMAGE THE UNIT AND VOID THE
WARRANTY.
INITIAL START UP
Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).
Before using the unit for the rst time, wipe down the exterior and toasting area with a damp
cloth. Take to a well ventilated area and heat for approximately 30 minutes. The grill may
emit a small amount of smoke as the cooking surfaces reach 450°F (232°C). Do not be
alarmed, as the smoke is caused by oils associated with the manufacturing process and will
stop when the burn off is complete. Brush off any debris from the toasting surface.
SEASONING THE COOKING SURFACES (NON CHROME SURFACES)
FIRST TIME SEASONING
Follow your company/corporate guidelines for seasoning cooking surfaces. or
1. Bring the grill to 300°F (149°C) and leave it on while doing the next two steps.
2. Brush the cooking surfaces with a SALT-FREE release agent. If using an aerosol agent,
rst apply into a cup and then brush onto cooking surface.
3. Let sit for 20 minutes, and then wipe clean using a warm damp cloth.
DAILY SEASONING
The grill should not require much seasoning while in use. In most cases, brush a light coating
of a SALT-FREE baking release agent in the morning and occasionally throughout the day will
be enough to prevent any sticking. It is not necessary to brush before grilling each item.
4
Page 5
PRESET TIME AND TEMPERATURE
If adjustments are required, please refer to the time or temperature programming section in
this manual.
°F/°C CONVERSION
To change the temperature display from °F to °C or from °C to °F, hold the TEMP button
while the unit is turned off. While holding the TEMP button, turn the unit on. The display
will be the changed temperature mode. To change back, repeat the procedure.
OPERATING INSTRUCTIONS
1. Turn unit on by placing switch in "ON" position. The "Heat On" indicator, program
number and display will ash indicating unit is heating. When the preset temperature is
reached, the heating light, display and program light indicator will stop ashing followed
by 3 beeps. (Initial startup heating time is approximately 30 minutes).
2. Place product on the bottom cooking surface of the unit and close the lids.
3. Press program button and let displayed time count down to "0" at which time unit will
beep. To turn off the beeper, press program button again.
4. Raise lids until it engages into rst indent and remove food. Using spatula, scrape
residue into grease catcher tray.
Note: Metal utensils with rounded corners may be used, however, using nonmetal
utensils will prolong the life of the cooking surface.
5. Turn the unit off when not in use.
TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS
Startup:
1. The preset time will ash until preset temperature is reached.
2. When the control reaches preset temperature, time display, "Heat On" indicator and
program indicator will stop ashing and the alarm will beep three times.
Temperature:
1. To view the actual temperature, press and hold "Temp Button." Display will read
"Lo F" if temperature is below 273°F (134°C) and "Hi F" if temperature is above
573°F (301°C).
5
Page 6
To Program Time and Temperature:
1. Press and hold "TEMP" (actual temperature displays).
2. While holding "TEMP," press and hold any program button on the Left one second, the
LED above the program number light and the display reads "_ _ _ _." Enter the four-digit
security code sequence, 4, 3, 2, 1. The security code will not show on the display. Once
the correct sequence has been entered, the preset time will be displayed and the LED for
that program will begin to ash.
3. Set the time with the "+ or -" buttons.
4. Press the "TEMP" button to save the time.
5. The preset temperature will now be displayed.
6. Set the desired temperature for this program using the "+ or -" buttons.
7. Press the "TEMP" button to save temperature and to exit programming mode for
this program. The LED will stop ashing but will remain lit.
8. Press any other program button within 15 seconds to continue programming without
re-entering the security code.
9. While programming a program (LED is ashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.
Note: Temperature settings are done with the left side buttons only. The time settings
programmed on the Left buttons will also be programmed onto the right side. See below to
make time changes to the right side only. Each programming change must be saved by
pressing the "TEMP" button!
Right Side (Timer only):
1. To Change the time on the right side, press and hold the "TEMP" button, and press and hold
any program button on the right for one second. The LED above the program button will
light and the Right Display will read "_ _ _ _." Enter the four-digit security code sequence,
4, 3, 2, 1. The security code will not show on the display. Once the correct sequence has
been entered, the preset time will be displayed and the LED for that program will begin to
ash.
2. Set the time with the "+ or -" buttons.
3. Press the "TEMP" button to save the time.
4. The LED will stop ashing but will remain lit.
5. Press any other program button within 15 seconds to continue programming without re-
entering the security code.
6. While programming a program (LED is ashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.
Operation:
1. Pressing any program button (1-4) will start the timer countdown and display the
preset time remaining. The LED for the appropriate program will be lit during
countdown and remain lit until another program is selected.
2. When the display reaches "00:00", the buzzer will sound and the digits will ash.
3. Press the program button to silence the buzzer and return the readout to programmed
time.
4. The right and left sides will operate independently of each other. Both timers can
be in operation at the same time. The "00:00" display will show which side is timed
out.
6
Page 7
MONTHLY INSPECTION
Check all bolts/screws and tighten if necessary.
CLEANING (NON-CHROME SURFACES)
Begin cleaning procedure by using the operating procedures within your organization, or follow
the steps below:
1. If particles adhere to the cooking surface during the day, scrape them off with a spatula.
NOTE: It is best not to let food residue onto the grill, as food build-up on the grill will
increase sticking and smoking. In addition, carbon may build up on the grill surface and
reduce the cooking efciency.
CARBON BUILDUP: A black matter that forms on or near the cooking surface. Generally this
is a combination of: releasing agents, oils, food particles etc. that has cooked itself to the
surface. After a period of time without cleaning, this will reduce performance and material
may start aking off. When that happens, follow the "Carbon Cleaning" procedures.
2. At the end of the day, wipe down all surfaces with a warm, damp cloth and mild detergent,
then dry.
CARBON CLEANING
When carbon build up occurs, use a carbon removal agent (safe for aluminum & chrome surfaces)
according to the instructions provided with the cleaner. When this process is complete, you
must re-season the grill according to your company/corporate guidelines, or the seasoning
instructions in this manual.
CAUTION
WARNING
DO NOT IMMERSE OR LET THE UNIT STAND IN WATER. DO NOT HOSE DOWN
THE UNIT. KEEP THE UNIT AWAY FROM RUNNING WATER.
DO NOT SPLASH THE CONTROL HOUSING! DO NOT SPLASH THE CONDUIT
CONNECTING THE TOP AND BOTTOM OF THE GRILL!
DO NOT USE ICE ON COOKING SURFACE!
BEFORE CLEANING ALL OTHER UNITS MAKE SURE POWER IS TURNED OFF
AND UNIT IS UNPLUGGED.
To remove burned on grease or food residue use the following mixture:
1 Tablespoon liquid dish detergent
1 Cup of warm water
While holding top lid with one hand, apply this mixture to cold or warm top cooking surface with
a sponge or plastic scrubbing pad. Wipe with clean sponge or towel until it is clean.
Empty and clean grease catcher tray as required using detergent and water after removing
tray from unit.
7
Page 8
THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL
This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition.
However, there are instances in which the unit may be damaged in transit. In the event you discover any type of damage
to your product upon receipt, you must immediately contact the transportation company who delivered the item to you
and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of the unit.
LIMITED EQUIPMENT WARRANTY FOR THE GR14SPTK-CN (9D-GR14SPTK-CN)
All workmanship and material in Star products have a one (1) year limited warranty on parts & labor. Such warranty is
limited to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's
obligation under this warranty is limited to the repair of defects without charge, by the factory authorized service agency
or one of its sub-agencies.
x
This warranty does not apply to any item that is disassembled or tampered with for any purpose other than
repair by the Middleby China Corporation or its Authorized Service Center or the Service Center's sub-agency.
x
This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, and wrong
gas or operated contrary to the Installation and Operating instructions.
x
Unless otherwise agreed, this warranty does not apply unless the defective parts are returned to the Middleby
China Corporation.
PARTS WARRANTY
Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted.
Labor to replace the part is chargeable to the customer.
SERVICES NOT COVERED BY WARRANTY
1. Travel time and mileage rendered beyond the 50 mile radius limit
2. Labor to replace such items that can be replaced easily during a daily cleaning routine, i.e.: grease drawers on
griddles, etc.
3. Installation of equipment
4. Damages due to improper installation
5. Damages from abuse or misuse
6. Operated contrary to the Operating and Installation Instructions
7. Cleaning of equipment
8. Seasoning of griddle plates
9. Voltage conversions
10. Gas conversions
11. Pilot light adjustment
12. Miscellaneous adjustments
13. Thermostat calibration and by-pass adjustment
14. Resetting of circuit breakers or safety controls or reset buttons
15. Replacement of bulbs
16. Replacement of fuses
17. Repair of damage created during transit, delivery, & installation OR created by acts of God
The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.
AUTHORIZED WARRANTY SERVICE
Middleby China Corporation
No. 98 Sheng Gao Road
Jiu Fu Development Zone
Jiuting Town
Song Jiang District
Shanghai, P.R. China.
Zip: 201615
Tel No.: 86-21-6769-0808
Fax No.: 86-21-6762-7640; 86-21-6762-7650
Email: samwang@middleby.com.cn
FOR ASSISTANCE
Should you need any assistance regarding the Operation or Maintenance of your sandwich grill; write, phone, fax or
email the Middleby China Corporation. In all correspondence mention the Model number, and Serial number of your unit.
8
Page 9
STAR MANUFACTURING INTERNATIONAL INC.
SK2350 Rev - 2/12/08
WIRE DIAGRAM, 230V, 2300 WATT
MODEL: GR14SPTK-CN
4
8
6 2
1 0
SENSOR - RIGHT
(SENSORIO)
BOTTOM ELEMENT
(ELEMENTO MAS BAJO)
TOP ELEMENT
RIGHT
(ELEMENT MAS ALTO)
E4
E3
E1
E5E6
1
3
15
16
13
14
3
1
10
9
10
9
8
7
7811
12
11
12
14
15
13
16
REAR OF CONTROLLER
E2
E11
E12
SENSOR - LEFT
(SENSORIO)
TOP ELEMENT
LEFT
(ELEMENT MAS ALTO)
TRANSFORMER
(TRANSFORMADOR)
RELAY
(RELE)
TERMINAL BLOCK
(BLOQUE TERMINAL)
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. THE TOP
DESCRIPTIONS ARE THEIR POSITIONS WHEN UPRIGHT.
1 0
8
4
6 2
SWITCH
(INTERRUPTOR)
E7
GREEN WITH
YELLOW
BROWN
BLUE
POWER CORD
CH2-16P PLUG
THESE ARE THE TWO YELLOW
WIRES FROM THE TRANSFORMER.
THEY CAN ATTACH TO EITHER E3 OR E4
ON CONTROL BOARD.
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
9
Page 10
FLAT
BREAD
1
2
QUES
3
CLEAN
4
TIME / TEMP
1
FLAT
BREAD
QUES
2
3
4
TEMP
TIME / TEMP
ON
HEAT
OFF
ON
4
5
36
12
35
37
10
1
15
25
27
16
21
18
6
20
38
8
44
30
9
13
铭牌
Nameplate
有些部件只供图示，
有时不一定需要。
49
STAR MANUFACTURING INTERNATIONAL, INC.
SK2333 REV. A 12/04/08
MODEL - GR14SPTK-CN
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
型号GR14SPTK-CN
55
54
57
52
53
56
51
61
60
62
17
2
41
43
41
33
22
3
32
47
28
24
7
45
11
40
46
34
23
19
14
50
51
52
48
10
Page 11
PARTS LIST September 30, 2011, Rev. E
GR14SPTK-CN Split Lid Table Top Grill
MODEL
Fig
Number
1 2A-Z6484 2 PLATE (COUNTER BALANCE MOUNT) 开启平衡装配板
2 D9-GR0150 1 GREASE CABINET ASSEMBLY 接油盘柜组装件
3 D9-GR0425 1 BODY ASSEMBLY 机身
4 D9-GR0177 1 BURN GUARD ASSEMBLY - LEFT 热防护板 左侧
5 D9-GR0176 1 BURN GUARD ASSEMBLY - RIGHT 热防护板 右侧
6 D9-GR0428 1 REAR PLATE ASSEMBLY 后背板
7 D9-GR0518 1 GREASE DRAWER ASSEMBLY 接油盘
8 D9-GR0182 2 TOP RETAINING PLATE ASSEMBLY 顶部固定板
9 PART OF ITEM #34 属于#34 件
10 2A-Y6142 4 SLEEVE HANDLE 手柄套筒
11 2A-Z7760 4 1" SOLID LEG 脚
12 2B-Z3336 4 14" GR14SPT ARM 长臂 14"GR14SPT
13 2C-Z3200 4 PIN - TOP HOUSING 顶盖固定柱
14 2C-Z3350 2 HALF CLAMP - .188 DIAMETER 半圆卡，直径 0.188"
15 2E-Z3808 1 SWITCH TOGGLE 开关
16 2E-Z11465 1 TRANSFORMER 230V/10V 变压器230V/10V 6VA
17 2R-GR0411 1 POWER CORD ASSEMBLY 电源线
18 2E-Z2894 1 TERMINAL BLOCK (304) 接线端子
19 D9-Z3903 2 BRACKET, PROBE MOUNT 探头固定片
20 2E-Z3278 2 RTD PROBE - 48" LONG WIRE RTD 探头 48" 线长
21 2E-Z3335 2 RELAY DOUBLE POLE - SINGLE THREAD 双柱继电器-单螺纹
22 2F-Z1945 1 CASTING - SMOOTH BOTTOM, ALUMINUM 底部铸件， 铝光板
23 2F-Z3237 2 CASTING - TOP 顶部铸件
24 2I-05-07-0013 1 BOOT SWITCH 启动开关
25 D9-GR0389 1 TIME/TEMPERATURE CONTROL 时间/温度控制
26 2K-Y8688 1 BUSHING 90 HEYCO #SR10-2 衬套 90 HEYCO #SR10-2
27 2K-Z1971 14 SPACER 垫圈
28 2M-12-07-0038 1 LABEL ON & OFF 开关标识
30 2M-Z11579 2 LABEL CAUTION, BI-LINGUAL 双语“小心”标签
32 2M-Z11488 1 OVERLAY 面板贴层
33 2N-Z9327 1 ELEMENT, HEATING, 1300 W 加热管 1300W
34 PS-Z9326 2 ELEMENT, HEATING, TOP 500W 顶部加热管 500W
35 2R-Z3345 1 COUNTERBALANCE - SPLIT TOP 分盖式开启平衡装置
36 2V-Z3152 2 HANDLE - TACO BELL 2 手柄
37 2V-Z3252 2 TOP HOUSING LATCH ROD 顶盖扳动手柄
38 B9-04-WB-0046 2 CLAMP WIRE SUPPORT 夹线卡
40 D9-Z2133 2 INSULATION FIBERGLASS TOP 顶部隔热棉
41 D9-Z8082 2 BOTTOM ELEMENT RETAINING PLATE 底部加热管挡板
43 D9-Z2888 1 INSULATION - 14" 底部隔热棉
44 D9-GR0181 2 TOP HOUSING AND CONDUIT ASSEMBLY 顶部箱盖组装件
45 D9-GR0217 1 BASE BOTTOM ASSY 14SPT 230V 底板组装件
46 D9-Z3902 2 PLATE - TOP ELEMENT RET. 顶部加热管挡板
47 Z1-70-07-0343 1 SWITCH GUARD 开关档片
48 D9-GR0189 2 TOP BURN GUARD ASSEMBLY 顶部热防护板组装件
Part
Number
Qty
Description 名称
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 1
INCLUDE MODEL AND SERIAL NUMBER OF 2
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
11
Page 12
PARTS LIST September 30, 2011, Rev. E
GR14SPTK-CN Split Lid Table Top Grill
MODEL
Fig
Number
49 D9-Z11677 1 INSULATION BAFFLE 隔热棉挡板组装件
50 D9-Z3826 1 INSULATION - BAFFLE 隔热棉-挡板
51 2A-Z6604 12 SPACER - INSULATION PLATE 挡圈-隔热棉挡板
52 2C-08-07-0285 12 SCREW 10-24X3/4X3/8 TYPE 2 HEX DBL END STL 不锈钢六角双头牙螺丝10-24X3/4X3/8
53 2C-Z2992 8 BOLT 1/4-20X1 PHP STL NP 不锈钢螺栓 1/4-20X1 PHP NP
54 2C-08-07-0262 8 WASHER 1/4 INT STL NP 不锈钢垫片 1/4 INT NP
55 2C-08-07-0040 8 NUT 1/4-20 ACHD STL NP 不锈钢螺母 1/4-20 ACHD NP
56 2C-Z2593 4 BOLT, 10-24x1 1/2 SL HX/W NP 螺栓 10-24X1 1/2 SL HX/W NP
57 2C-Z5883 8 SCREW, 10-24 X 1/2 FZA, SELF DRILLING 钻尾螺丝10-24X1/2 FZA
58 2E-Z11487 2 SLEEVE, WIRE 套筒，变压器黄色引线
59 2E-Z3768 2 LOCKNUT, CONDUIT 防松螺母，导线
60 2C-1516 1 SCREW 10-24X1 STL RH
61 2C-Z11667 2 .375 TUBE CLAMP GALV/
62 2C-Z2893 1 NUT 10-24 HEX STL ZP
Part
Number
Qty
Description 名称
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE 2
INCLUDE MODEL AND SERIAL NUMBER OF 2
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
12
Loading...