®
®
®
®
®
TABLE TOP
TWO SIDED
TOASTER
MODEL
GR10T4K-UK, GR10T4K-CE
Installation and
Operation
Instructions
2M-Z9364 Rev. A 1/31/2011
1
2
These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTICE
Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.
Star reserves the right to change specifi cations and product design without
notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.
Due to periodic changes in designs, methods, procedures, policies and
regulations, the specifi cations contained in this sheet are subject to change
without notice. While Star Manufacturing exercises good faith efforts to provide
information that is accurate, we are not responsible for errors or omissions
in information provided or conclusions reached as a result of using the
specifi cations. By using the information provided, the user assumes all risks in
connection with such use.
MAINTENANCE AND REPAIRS
Contact your local dealer for service or required maintenance. Please record the model number, serial
number, voltage and purchase date in the area below and have it ready when you call to ensure a faster
service.
SAFETY SYMBOL
Model No.
Serial No.
Voltage
Purchase Date
FOR SERVICE CONTACT:
Servequip
Telephone: 011-44-208686-8855
2
ELECTRICAL SPECIFICATIONS
Model No. Volts Rated Wattage Amps Power Inlet
GR10T4K-UK 230 1653 7.2 IEC320 C20 Power inlet
GENERAL INSTALLATION DATA
CAUTION
This equipment is designed and sold for commercial use only by personnel trained and
experienced in its operation and is not sold for consumer use in and around the home nor for
use directly by the general public in food service locations.
All shipping containers should be checked for freight damage both visible and concealed. This
unit has been tested and carefully packaged to insure delivery of your unit in perfect condition.
If equipment is received in damaged condition, either apparent or concealed, a claim must be
made with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked,
a request for inspection of concealed damage must be made with carrier within 15 days. Be
certain to retain all contents plus external and internal packaging materials for inspection. The
carrier will make an inspection and will supply necessary claim forms.
VENTILATION AND CLEARANCES
The installation of any components such as a vent hood, grease extractors, and/or re
extinguishing systems, must conform to their applicable nationally recognized installation
standards and/or local building codes.
ELECTRICAL CONNECTION
CAUTION
Before making any electrical connection be sure to read the data plate located at the
bottom of the unit.
CAUTION
CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE
DATA PLATE OF THE UNIT.
ELECTRICAL GROUNDING INSTRUCTIONS
CAUTION
This unit is equipped with a 3-prong (grounding) plug for your protection against shock hazard
and must be plugged directly into a properly grounded 3-prong receptacle.
DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING PRONG FROM THE
PLUG.
INITIAL START UP
Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).
Unpack the grill and put the owner's manual in a safe place for future reference. Wipe down
the exterior and grilling area with a damp cloth. Brush any debris from the grill surfaces.
3
SEASONING THE COOKING SURFACES
FIRST TIME SEASONING
Follow your company/corporate guidlines for seasoning cooking surfaces. or
1. Bring the grill to 300°F and leave it on while doing the next three steps.
2. Brush the cooking surfaces with a release agent. If using an aerosol agent,
rst apply into a cup and then brush onto cooking surface.
3
. Let sit for 20 minutes, and then wipe clean using a warm damp cloth.
DAILY SEASONING
The grill should not require much seasoning while in use. In most cases, brush a light coating
of the baking release agent in the morning and occasionally throughtout the day will be enough
to prevent any sticking. It is not necessary to spray before grilling each item.
SETTING THE TEMPERATURE
The thermostat control knob is used to set the temperature to your requirements. The maximum
set point is 550°F (288°C), the minimum set point is 175°F (79°C).
Knob Position Approx. Temp
1-2 175°F / 79°C
3
4 250°F / 121°C
6 350°F / 176°C
1
200°F / 93°C
5 300°F / 148°C
7 400°F / 204°C
8 450°F / 232°C
9 500°F / 260°C
0 550°F / 287°C
PROGRAMMING THE TIMER
The timer may be factory pre-set. If changes are required follow these steps:
1. Press and hold the PGM button located on the left side of the display.
2. Press and hold one of the buttons (1 through 4) that needs to be programmed. After
approximately 1 second, the display window will show "_ _ _." When this is displayed, let
go of the buttons.
3. Enter the 3-digit security code. As the digits are entered, the corresponding horizontal bar
will move from the bottom to the center. The security code will not be displayed. Once
the correct security code is entered, the display will be the current time of the selected
button.
4.
Change the time by pressing and holding the
button
5. Once the correct time is displayed, press the PGM button to save the time.
6. One can now change the time by pressing another button and repeating steps 3 and 4.
7. When programming is complete, exit the programming mode by not pressing any buttons
for 15 seconds.
to increase the time or the button to decrease the time.
4
ON/OFF TOGGLE SWITCH
The switch turns the unit on and off. The switch has three positions:
With the switch in this position, both top and bottom platens
will heat.
With the switch in this position, neither platen will heat;
the unit is OFF.
W
will heat.
ith the switch in this position only the bottom platen
DAILY OPERATION
Make sure the unit is plugged into a 15 amp, 230V receptacle.
1. Turn the electrical power of the unit ON by placing the switch in either the up or down
position. IMPORTANT: The heat will not start until the thermostat is also turned to the
heating position, approximately 2 or higher on the dial.
2. To start heating, turn the temperature knob to the desired setting. Initial start-up heating
time is approximately 30 minutes.
3. Place product(s) on the bottom cooking surface.
4. Close the lid if the top if also ON. If the top is OFF, the unit can be operated similar to a
griddle.
5. Press the desired button (1 through 4) on the timer. The timer countdown will begin
regardless of what button is pressed.
6. When the countdown reaches 0:00, the display will ash and the unit will beep. To turn off
the beeping, press the same button (1 through 4) used to start the countdown.
NOTE: If one wants to end a countdown, the same button (1 through 4) can be pressed at
any time in the countdown cycle. The display will return to the programmed time for that
button.
7. Raise the lid to the open position and remove the product(s).
8. For best performance, keep the lid closed when products are not being cooked.
OPERATING HINTS AND SAFETY
Disconnect power to the unit with the switch at the end of each day of operation. Do not leave
the unit in operation without an attendant.
Turn the thermostat down to 200°F (93°C) during idle periods. It will take only a few minutes
to regain operating temperature. Use a spatula to push excess grease into the grease drawer
after each load of food is cooked. This will reduce smoking of hot grease and carbonizing.
Do not leave the unit at high temperatures when not in use or during idle periods. This will
cause food particles and grease lm to carbonize.
"Season"
cooking surfaces with non-salted vegetable oil to reduce product sticking.
MONTHLY LUBRICATION/INSPECTION
Apply two (2) drops of non-toxic mineral or vegetable oil to counter balance shoulder rivets
and plastic spacers.
Check and clean rollers to make sure they are rolling and not sliding on the cam surfaces of
the counterbalance. Check the bolts, screws and nuts; tighten if necessary.
5
CLEANING
Begin cleaning procedure by using the operating procedures within your organization, or follow
the steps below:
1. If particles adhere to the cooking surface during the day, scrape them off with a spatula.
NOTE: It is best not to let food cook onto the grill, as food build-up on the grill will increase
sticking and smoking. In addition, carbon may build up on the grill surface and reduce the
cooking efciency.
CARBON BUILDUP: A black matter that forms on or near the cooking surface. Generally this
is a combination of: releasing agents, oils, food particles etc. that has cooked itself to the
surface. After a period of time without cleaning, this will reduce performance and material
may start aking off. When that happens, follow the "Carbon Cleaning" procedures.
2
. At the end of the day, wipe down all surfaces with a warm, damp cloth and mild detergent,
then dry.
CARBON CLEANING
When carbon build up occurs, use a carbon removal agent according to the instructions provided
with the cleaner. When this process is complete, you must re-season the grill according to your
company/corporate guidelines, or the seasoning instructions in this manual.
CAUTION
DO NOT IMMERSE OR LET THE UNIT STAND IN WATER.
DO NOT HOSE DOWN THE UNIT OR THE TABLE/COUNTER ON WHICH THE UNIT
IS LOCATED.
KEEP AWAY FROM RUNNING WATER.
CAUTION
DO NOT USE SHARP OBJECTS TO REMOVE CARBON BUILD-UP.
BEFORE CLEANING MAKE SURE POWER IS TURNED OFF, UNIT IS UNPLUGGED
AND IS NOT TOO HOT.
While holding top lid with one hand, apply only cleaners which are safe for aluminum and iron
surfaces. Wipe with clean sponge or towel until unit is clean.
CAUTION
DO NOT SPLASH FRONT CONTROL PANEL!
DO NOT SPLASH THE FLEX CONDUIT CONNECTING THE TOP AND BOTTOM
OF THE UNIT.
Remove and empty the grease catcher drawer, to clean using mild detergent and water.
CAUTION
Do not use ice or cold water to clean the cooking surfaces when the unit is hot.
The surfaces are cast aluminum or cast iron and may crack or deform under the
shock of rapid temperature change.
6
OPERATION TROUBLESHOOTING
A. Unit is not heating.
1. Check if the unit is plugged into the correct receptacle.
2. Check the incoming power line.
3. Check that the switch is in the correct position.
4. Check that the thermostat is set to the proper temperature.
B. The top platen is not heating.
1. Check that the switch is in the correct position.
C. The counter balance roller is not rolling.
1. Clean the rollers.
If the unit still does not operate, contact the factory, one of its authorized representatives,
or a local service company for service or required maintenance.
7
INTERNATIONAL ONE (1) YEAR EQUIPMENT WARRANTY
All workmanship and materials in “STAR” products are warranted for a period of one year from the date shipped from the factory or
one year from the date shown on the proof of purchase of the end-user when purchased through an authorized “STAR” dealer/dis-
tributor in a commercial foodservice location.
“STAR’s” obligation under this warranty is limited to the replacement of the defective part(s) only without charge. This warranty is
void if damage occurs from improper installation, misuse or abuse, disassembly or tampering of unit for any purpose other than repair
by a qualifi ed service agent, wrong voltage, incorrect or fl uctuating voltage conditions, wrong gas, improper gas or gas conditions,
operated contrary to the installation and operating instructions, operated in an application for which the unit is not suited, or if the unit
is not maintained and/or cleaned in a suitable manner.
Any expense in connection with installation, or any cost of making adjustments on a unit to conform to electric or gas service at the
point of installation, are not covered by this warranty.
* The warranty period for the JetStar series six (6) ounce popcorn machines is two (2) years.
* The warranty period for the Chrome-Max Griddles is fi ve (5) years on the griddle surface. See detailed warranty provided with unit.
* The warranty period for Tefl on/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not
apply if damage occurs to Tefl on/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive
cleaners. This warranty does not apply to the “non-stick” properties of such materials.
* This warranty is not valid on Conveyor Ovens unless a “start-up/check-out has been performed by a Factory Authorized Technician.
In order to make a claim under this warranty; a warranty report must be fi led with Star Manufacturing International Inc. in St. Louis,
Missouri, U.S.A. by the dealer/distibutor through which product was purchased. All details, including serial number and model number of the defective unit, must be included. Failure to fi le a claim within a 120 Day time period may result in the claim being refused.
“STAR” may forego the necessity of returning the part for inspection dependent upon the expense involved. However, “STAR”
requires defective parts to be held in the claimant’s possession for a period of ninety (90) days for possible inspection by a “STAR”
representative or designated inspector .
The foregoing warranty is lieu of any and all other warranties, expressed or implied, and constitutes the entire warranty.
PARTS WARRANTY
Parts that are sold for out-of-warranty repair are warranted for a period of ninety days. The part only is warranted; no labor.
SERVICES NOT COVERED BY WARRANTY
1. Labor
2. Mileage and/or travel time
3. Installation and/or adjustment of equipment
4. Operation contrary to the installation and operating instructions
5. Cleaning of equipment
6. Seasoning of griddle plates
7. Voltage conversions/adjustments
8. Gas conversions
9. Pilot light conversion/adjustments
10. Thermostat calibration/adjustments
11. Resetting of circuit breakers or safety controls
12. Replacement of bulbs/lamps
13. Replacement of fuses
14. Damages due to improper installation
15. Damages from abuse or misuse
16. Damage created by acts of God, Acts of War, or Civil Disturbance
08-05 rms
8
WIRE DIAGRAM, CG/GR, 10/14, 120V/230/240V, WITH TIMER
STAR MANUFACTURING INTERNATIONAL, INC.
MODEL: SEE ABOVE
SK2001 REV. C 12/12/2005
B
A
C
D
GREEN
BLACK
WHITE
NORTH AMERICA:
15 AMP PLUG
NEMA 5-15P ON 120V, 1,800 WATT UNITS FOR U.S. ONLY.
NEMA 5-15P ON 120V, 1,400 WATT UNITS FOR U.S. AND CANADA.
NEMA 6-15P ON ALL 240V, 1,800 WATT UNITS.
20 AMP PLUG
NEMA 6-20P ON ALL 240V, 3,600 WATT UNITS.
NEMA 5-20P ON 120V, 1,800 WATT UNITS FOR U.S. AND CANADA.
TOP ELEMENT
TRANSFORMER
TERMINAL BLOCK
FOR REFERENCE
WIRING DIAGRAM IS SHOWN AS UNIT IS ASSEMBLED
WITH THE BOTTOM PLATE REMOVED. ITEMS ARE IN
GENERAL LOCATION BUT MAY BE RELOCATED OR SCALED
FOR CLARITY.
8
8
1
1
11
12
12
11
5
2
52
4
4
10
10
9
9
13
3
3
7
6
7
INDICATOR LIGHT
(POWER ON)
TIMER BOARD
SWITCH
THERMOSTAT
BOTTOM ELEMENT
20
19
18
G
UNITS WITH IEC CONNECTOR:
POWER INLET CONNECTOR:
IEC 320 C-20 POWER INLET, ON ALL 208 - 240V UNITS.
FOR USE WITH DETACHABLE CORDSETS SUPPLIED
WITH A STRAIGHT, FEMALE, IEC 60320 C-19 CONNECTOR.
L N
E
REAR OF CONNECTOR SHOWN.
6
13
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
9
35
34
14
PELIGRO
SUPERIFICIE
FAVOR NO
TOCAR
CALI
ENTE
HOT SURF
ACE.
DONOT TOUCH
Donot hos
e d
own.
Keep away from
running wa
ter.
PRECAUCION
Main
tengaselejos de
manguera.
No rocia
con
corriente
de
agu
a.
o dejar que la base este
estancada sobre
agua
Favorde no s
umergir
DANGER
Do
not immerseor let
CAUTION
base standinwater.
Keep away from
runn
ing water.
DANGER
HOT SURFA
CE.
DONOT TOUCH
PELIGRO
corrie
nte de ag
ua.
SUPER
IFICIE
FAVOR NO TOCAR
CALIENTE
PRECAUCION
Maintengaselejos de
manguera
.
No rocia con
o dejar que la base este
estanc
ada s
obre agua
Favorde no s
umergir
Do not hose dow
n.
Do not
immerseor let
CAUTION
base stan
d
inwater.
11
13
10
9
12
1
43
5
40
7
2
4
8
18
19
39
20
21
22
44
23
24
25
26
37
49
33
27
27
29
30
31
3
6
17
52
51
46
45
50
47
48
NAMEPLATE
55
54
53
STAR MANUFACTURING INTERNATIONAL, INC.
CERTAIN INSTANCES MAY NOT BE AVAILABLE
ILLUSTRATIVE PURPOSES ONLY AND IN
SOME ITEMS ARE INCLUDED FOR
MODEL: GR10T4K
SK2164 REV. -
1/10/2006
No reproduction or disclosure of its
to Star Manufacturing International, Inc.
This drawing contains information confidential
contents is permitted.
52
10
PARTS LIST January 31, 2011 Rev. A
Star Two-Sided Grill
GR10T4K-UK
MODEL
Key
Number
1 2M-Z9363 1 OVERLAY W/TIMER - 10"
2 2J-Z7668 1 TIMER CONTROL
3 2K-Z1971 4 SPACER
4 2E-Z6863 1 SWITCH - 3 POSITION
5 2R-Z4621 1 KNOB - CONTROL
6 2T-6447 1 THERMOSTAT 118V-236V
7 D9-GR0234 1 FACEPLATE ASSEMBLY - 10" WITH TIMER
8 D9-GR0328 1 BODY ASSEMBLY - 10"
9 D9-GR0034 1 GREASE CABINET ASSEMBLY
10 D9-GR0215 1 GREASE DRAWER ASSEMBLY
11 2A-Z7760 4 FOOT - 1" ADJUSTABLE
12 D9-GR0302 1 BASE BOTTOM - 10"
13 2E-Z9192 1 CORD POWER
14 2K-Y3240 1 BUSHING HEYCO SR 17-2
17 2A-Z6484 2 PLATE - COUNTER BALANCE MOUNT
18 D9-GR0053 1 REAR LINER ASSEMBLY - 10" BOTTOM
19 2E-Z2894 1 TERMINAL BLOCK
20 2E-05-07-0350 1 TRANSFORMER 230V/10V 6VA
21 2R-Z2907 1 COUNTER BALANCE - 10" IRON
22 D9-Z2774 1 BOTTOM INSULATION RETAINING PLATE - 10"
23 D9-Z2908 1 INSULATION - 10"
24 D9-Z2773 1 BOTTOM ELEMENT RETAINING PLATE - 10"
25 2N-Z2020 1 ELEMENT, HEATING 1000W/240V (BOTTOM) 230V
26 2F-Z1929 1 CASTING - SMOOTH BOTTOM - 10" ALUMINUM
27 D9-Z2772 1 TOP ELEMENT - INSULATED PLATE - 10"
28 D9-GR0084 1 TOP RETAINING PLATE ASSEMBLY - 10"
29 B9-04-WB-0046 1 CLAMP WIRE SUPPORT
30 PS-Z2019 1 ELEMENT - HEATING 800W/240V (TOP) 230V
31 2F-Z1928 1 CASTING - SMOOTH TOP - 10" ALUMINUM
33 2C-Z3200 2 PIN - TOP HOUSING
34 2B-Z2988 2 ARM - 10"
35 2V-Z2990 1 HANDLE - 10"
37 2M-Z2620 1 LABEL - CAUTION (BI-LINGUAL)
39 2V-Z3252 1 ROD - TOP HOUSING LATCH
40 2A-Z3026 1 HALF CLIP .437
43 2I-05-07-0013 1 BOOT - SWITCH
44 2A-Z6604 8 SPACER - INSULATION PLATE
45 2I-Z3380 2 THERMOSTAT SEAL WASHER
46 2I-Z3379 1 GROMMET - THERMOSTAT
47 2C-Z2899 2 5/16-18 UNC LOCKNUT
48 1O-E1500 0.33 SLEEVING #4 .208ID GLASS
49 D9-GR0203 1 TOP HOUSING AND CONDUIT ASSEMBLY
50 2E-Z3768 1 LOCKNUT, CONDUIT, 1/2 INCH
51 2J-Z2329 1 PILOT LIGHT 230V
52 2C-08-07-0285 8 STUD, SELF TAPPING
53 D9-GR0326 1 TOP BURN GUARD ASSY. 10"
54 D9-GR0327 1 BURN GUARD ASSY. FRONT & SIDE - 10"
55 2E-Y9253 1 INLET IEC320 16 AMP
Part
Number
Number
Per
Unit
Description
1
IMPORTANT: WHEN ORDERING, SPECIFY VOLTAGE OR TYPE GAS DESIRED PAGE
1
INCLUDE MODEL AND SERIAL NUMBER OF
Some items are included for illustrative purposes only and in certain instances may not be available.
Star Manufacturing International, Inc.
11
STAR INTERNATIONAL HOLDINGS INC. COMPANY
Star - Holman - Lang - Wells - Bloomeld - Toastmaster
10 Sunnen Drive, St. Louis, MO 63143 U.S.A.
(314) 781-2777
www.star-mfg.com
Loading...