Page 1
Revolt
Universal Wireless and Wired Headphones with Docking Station for Audio Streaming.
User Guide
Page 2
1. Introduction
This 2.4GHz stereo wireless headphone system offers you advances in wireless transmission technology.
You can listen to stereo sound from your audio components up to 50 meters. The transmitter is
compatible to any audio sources such as DVD player, CD player, i-Pod, MP3, TV set, VCR, Hi-Fi system and
radio.
2. Features
2.4GHz FHSS Digital technology.
High quality stereo sound that is virtually interference-free.
Transmission unrestricted by line of sight
Digital Pairing System on Headphone & Transmitter
Electronic Volume Control on Headphones
Built-in Pin-charger on transmitter
Auto Shut-off on headphone
Auto On/Off RF function on transmitter
3.5mm Line in feature for wired headphone application
Operating distance up to 50 meters
3. Inside the Box
RF receiver headphone
RF transmitter
6V 300mA power adapter
3.5mm to 3.5mm cable
3.5mm jack to RCA cable
Instruction Manual
4. Specifications
Transmission mode: 2.4GHz digital FHSS stereo
Carrier frequency: 2.4GHz
Operating voltage: Transmitter 6 V 300 mA
Receiver: 3.7V 470mA (built-in Lithium rechargeable battery)
Frequency response: 20 Hz – 20 KHz (electrical)
Distortion: 0.5 %
Signal-to-noise ratio: 75 dB
Channel separation: 60 dB
Range: 50 meters (open area)
Page 3
5. Installation
POWER/SIGNAL
1
2
3
4
1. Power LED Indicator
2. Power Key
3. Vol+, Pair, Vol-
4. 3.5mm Audio In Jack
TRANSMITTER
1. Connect the power adapter provided to a power outlet.
2. Connect the power adapter to the DC IN input connector located on the transmitter’s rear panel.
3. Use the audio cable 3.5mm jack to RCA cable to connect the transmitter with the audio outputs
on audio sources like TV set, Hi-Fi system, iPods, VCR or radio-cassette player.
4. Turn the ON/OFF switch to ON and the Green LED indicator will light up. The Blue LED indicator
will light up when audio source is on. If the Blue indicator LED remains off, switch on the audio
source and increase its output level until the Blue indicator lights up.
HEADPHONE RECEIVER
Page 4
1. Press the Power button on the headphone for 3 seconds to turn the wireless function on. The
Blue LED light will flash.
2. The headphones are now linked up with the transmitter and the Blue LED light will be solid blue.
6. Installation
To start up this system, please take following steps:
Connect the power adapter between the transmitter and power outlet. The LED on the
transmitter will light up green.
Connect the transmitter with your audio source, turn the source ON, and then the LED will turn
from Green to Blue.
Turn on the headphone receiver by pressing the ON/OFF switch, and then LED will then flash in
blue.
If the LED on the headphone turns OFF immediately, recharge headphones.
When the audio link is established, the LED will turn blue.
If the LED on the headphone still flashes in blue, please check with troubles shooting processes.
To pair the Headphone receiver with the transmitter, please take the following steps:
Press the Pair button on the transmitter and the headphone simultaneously for 3 seconds.
The blue LED will begin to flash.
The LED will change to solid Blue when pairing process is finished.
To activate auto stand by and auto shut off, please take the following steps:
The transmitter will automatically turn to stand by mode after approximately 4 minutes if there
is no audio signal, or the signal that it receives from the audio source is too weak for proper
reception.
If however the signal returns to an acceptable level, the transmitter will automatically switch
back on.
The headphone receiver will automatically shut off if there is no signal from the transmitter after
15 minutes.
7. Charging the Batteries
1. Switch OFF the receiver headphone.
2. To recharge the headphone batteries, place the headphones onto the transmitter, and ensure
that the charge contacts touch the transmitter's charge pins. The LED on the headphone will
light up in red, when charging is finished the headphone LED will turn green.
3. Charge the batteries in the headphones for 5 hours when using for the first time. The red
indicator light will be in solid red during battery charging.
Page 5
8. Wired Headphone Application
The headphone can be applied in wired mode. Simply connect the headphone and the audio source by
the supplied 3.5mm to 3.5mm audio cable.
9. Troubleshooting
NO SOUND
Ensure that the mains adapter is pushed fully into the power outlet and that its cable is properly
connected to the DC IN 6V connector on the transmitter.
Ensure that the headphones On/Off switch is switched to the On
The headphones battery charge level may be too low. Recharge the batteries or replace them
with fully charged batteries.
Ensure that your DVD, TV set, Hi-Fi system or audio component is switched on and set to a
channel that broadcasts an audio signal.
Page 6
Use the headphones volume control to increase the sound level (only when use as a wireless
headphone).
The audio signal input level is too low. Increase the volume from the audio source of Hi-Fi, CD, or
TV, etc.
The connected audio/video equipment may not be in playback mode. Start playback on by the
equipment.
The headphones output level is set too low. Adjust the volume to a suitable level.
DISTORTION
Restart the Pairing process. Press the “Pair” button on the transmitter and the headphones for
3secs. The process is finished when both LEDs flash blue.
The headphone’s batteries may be too low. Recharge the batteries.
Ensure that the volume knob setting is correct.
The headphones may be too far away from the transmitter.
The audio signal input level may be too low. Increase the volume from the audio source of Hi-Fi,
CD, or TV, etc.
WARNINGS
Battery:
Never use another type of battery to replace the rechargeable batteries. When the headphones
are not in use, switch OFF the headphones to avoid damaging the batteries.
The batteries must be fully charged when using for the first time. An initial 5 hours charge is
required to guarantee an acceptable service life for the rechargeable batteries. Always ensure
that the headphones are switched to the OFF position while the batteries are charging.
Replace only with the same or equivalent type.
Keeping the device out of the reach of small children:
The packing products and the plastic bags for the accessories are not toys.
The bag itself and those small fittings inside can cause suffocation. Do not attempt to
disassemble the device. No parts embedded can be replaced or repaired by users.
Only authorized dealers or maintenance centers can disassemble this product. For issues with
any parts including normal wear, break, or damages, please contact your dealer.
Keep the product away from rain or other liquids.
Loading...