ProLogic PL100 Instruction Manual

E F G

Thank you for purchasing the ProLogic PL100 Digital Automatic Blood Pressure Monitor.

The ProLogic PL100 is a compact, fully automatic blood pressure monitor, operating on the oscillometric principle. It measures your blood pressure and pulse rate simply and quickly.

Intended Use This product is designed to measure the blood pressure and pulse rate of people within the range of the designated arm cuff, following the instructions in this instruction manual. It is mainly designed for general household use. Please read the Important Safety Information in this instruction manual before using the unit.

Please read this instruction manual thoroughly before using the unit. Please keep for future reference. For specific information about your own blood pressure, CONSULT YOUR DOCTOR.

Consult your doctor prior to using in pregnancy or if diagnosed with arrhythmia or arteriosclerosis. Please read this section carefully before using the unit.

Important Safety Information

Introduction

1. Overview

Main unit:

Arm cuff:

I. Systolic blood pressure J. Diastolic blood pressure K Heartbeat symbol (Flashes during measurement) L. Battery low symbol

2.1 Installing/Replacing the Batteries

2. Preparation

Remove the battery cover.

Insert four “AAA” batteries as indicated in the battery compartment and then replace the battery cover.

Notes:

• If the battery low symbol ( ) appears on the display, turn the unit off

then replace all batteries at the same time.

Disposal of used batteries should be carried out in accordance with the national regulations for the disposal of batteries.

The bottom edge of the cuff should be 1 to 2 cm above the elbow. Marker (arrow under tube) is centred on the middle of your inner arm. Close the fabric fastener FIRMLY.

3. Using the Unit

1. Insert the air plug into the air jack.

2. Put your arm through the cuff loop.

3. Position the arm correctly.

Systolic Blood Pressure Above 135 mmHg

Diastolic Blood Pressure Above 85 mmHg

3.1 Applying the Arm Cuff

3.3 Taking a Reading

Notes:

• When you take a measurement on the right

arm, air tube will be at the side of your elbow. Be careful not to rest your arm on the air tube.

Notes:

• To cancel a measurement, press the O/I START button to turn off the

unit and to release the air in the arm cuff.

• Remain still while taking a measurement.

Remove tight-fitting clothing or tight rolled up sleeve from your upper arm. Do not place the cuff over thick clothes.

3.2 How to Sit Correctly

To take a measurement, you need to be relaxed and comfortably seated, under comfortable room temperature. No eating, smoking or exercising 30 minutes before taking a measurement.

• Sit on a chair with your feet flat on the floor.

• Sit upright with your back straight.

• The cuff should be at the same level as your

heart.

1 to 2 cm

• The blood pressure can differ between the right arm and the left arm,

and therefore also the measured blood pressure values can be different. OMRON recommends to always use the same arm for measurement. If the values between the two arms differ substantially, please check with your physician which arm to use for your measurement.

Remove the arm cuff.

Press the O/I START button to turn the monitor off.

It will automatically turn off after five minutes.

Note:

Wait 2-3 minutes before taking another blood pressure measurement. Waiting between readings allows the arteries to return to the condition

prior to taking the blood pressure measurement.

Self-diagnosis of measured results and treatment are dangerous. Please follow the instructions of your doctor.

Warning:

• Recent research suggests that the following

values can be used as a guide to high blood pressure for measurements taken at home.

Important:

Digital Automatic Blood

Pressure Monitor

Model PL100

Instruction Manual

A. Display

B. O/I START ( ) button

C. Air Jack D. Battery compartment

E. Arm cuff (Medium Cuff: arm

circumference 22-32 cm) F. Marker G. Air tube H. Air plug

M. Pulse display N. Deflation symbol

Display:

IM-HEM-7101-PR-01-05/2012

5334832-1A

Press the O/I START button.

The cuff will start to inflate automatically.

START

INFLATE DEFLATE

COMPLETE

If your systolic pressure is more than 140 mmHg

After the cuff starts to inflate, press and hold the O/I START button until the

monitor inflates 30 to 40 mmHg higher than your expected systolic pressure.

Notes:

• The monitor will not inflate above 299 mmHg.

• Do not apply more pressure than necessary.

Warning:

• Indicates a potentially hazardous situation which, if not avoided, could result

in death or serious injury.

(General Usage)

• Always consult your doctor. Self-diagnosis of measurement results and

self-treatment are dangerous.

• People with severe blood flow problems, or blood disorders, should consult a

doctor before using the unit, as cuff inflation can cause internal bleeding.

(Battery Usage)

• If battery fluid should get in your eyes, immediately rinse with plenty of clean

water. Consult a doctor immediately.

Caution:

• Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury to the user or patient or damage to the equipment or other property.

(General Usage)

• Do not leave the unit unattended with infants or persons who cannot express

their consent.

• Do not use the unit for any purpose other than measuring blood pressure.

• Use only the approved arm cuff for this unit. Use of other arm cuffs may result

in incorrect measurement results.

• Make sure that the air tube is not wrapped around other parts of your body

when taking measurements. This could result in injury when the air pressure in the air tube is increased.

• Do not leave the cuff wrapped on the arm if taking measurements during the

night. This could result in injury.

• Do not use a mobile phone or other devices that emit electromagnetic fields,

near the unit. This may result in incorrect operation of the unit.

• Do not operate the unit in a moving vehicle (car, airplane).

• To inflate the cuff manually, refer to Section 3.3. If the cuff is over inflated, it

can cause internal bleeding.

(Battery Usage)

• If battery fluid should get on your skin or clothing, immediately rinse with

plenty of clean water.

• Use only four “AAA” alkaline or manganese batteries with this unit. Do not

use other types of batteries.

• Do not insert the batteries with their polarities incorrectly aligned.

• Replace old batteries with new ones immediately. Replace all four batteries at

the same time.

• Remove the batteries if the unit will not be used for three months or more.

• Do not use new and used batteries together.

General Precautions

• Do not apply strong shocks and vibrations to or drop the unit and arm cuff.

• Do not take measurements after bathing, drinking alcohol or caffeine,

smoking, exercising or eating.

• Do not forcibly bend the arm cuff or bend the air tube excessively.

• When removing the air tube, pull on the air plug at the connection with the

main unit not the tube itself.

• Do not inflate the arm cuff when it is not wrapped around your arm.

• Read and follow the “Important information regarding Electro Magnetic

Compatibility (EMC)” in the Technical Data Section.

• Read and follow the “Correct Disposal of This Product” in the Technical Data

Section when disposing of the device and any used accessories or optional parts.

This criteria is for home blood pressure measurement.

Personal Blood Pressure Diary

Date

Time

Systolic (higher reading)

Diastolic (lower reading) Pulse

Body weight (kg)

Medication prescribed

250

mmHg

240 mmHg

230 mmHg

220 mmHg

210 mmHg

200 mmHg

190 mmHg

180 mmHg

170 mmHg

160 mmHg

150 mmHg

140 mmHg

130 mmHg

120 mmHg

110 mmHg

100 mmHg

90 mmHg

80 mmHg

70 mmHg

60 mmHg

50 mmHg

SYS (Systolic)

DIA (Diastolic)

Note: Subject to technical modification without prior notice.

Important information regarding Electro Magnetic Compatibility (EMC)

With the increased number of electronic devices such as PC’s and mobile (cellular) telephones, medical devices in use may be susceptible to electromagnetic interference from other devices. Electromagnetic interference may result in incorrect operation of the medical device and create a potentially unsafe situation. Medical devices should also not interfere with other devices.

In order to regulate the requirements for EMC (Electro Magnetic Compatibility) with the aim to prevent unsafe product situations, the EN60601-1-2:2007 standard has been implemented. This standard defines the levels of immunity to electromagnetic interferences as well as maximum levels of electromagnetic emissions for medical devices.

This medical device manufactured by OMRON HEALTHCARE conforms to this EN60601-1-2:2007 standard for both immunity and emissions. Nevertheless, special precautions need to be observed:

• Do not use mobile (cellular) telephones and other devices, which generate strong electrical or electromagnetic fields, near the medical device. This may result in incorrect operation of the unit and create a potentially unsafe situation. Recommendation is to keep a minimum distance of 7 m. Verify correct operation of the device in case the distance is shorter.

Further documentation in accordance with EN60601-1-2:2007 is available at OMRON HEALTHCARE EUROPE at the address mentioned in this instruction manual. Documentation is also available at www.omron-healthcare.com.

This marking shown on the product or its literature, indicates that it should not be disposed of, with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this product from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can return this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

Made in China

4. Troubleshooting and Maintenance

6. Technical Data

5. Optional Parts

4.1 The Icons and Error Messages

4.3 Maintenance

Calibration and Service

To protect your unit from damage, please observe the following:

• Do not subject the main unit and the cuff to extreme

temperatures, humidity, moisture or direct sunlight.

• Do not fold the cuff or tubing tightly.

• Do not disassemble the unit.

• Do not subject the unit to strong shocks or vibrations

(for example, dropping the unit on the floor).

• Do not use volatile liquids to clean the main unit.

• Do not wash the arm cuff or immerse it in water.

• Do not use petrol, thinners or similar solvents to clean

the arm cuff.

• Do not carry out repairs of any kind yourself. If a defect

occurs, consult your OMRON retail outlet or distributor as mentioned on the packaging.

• The accuracy of this blood pressure monitor has been

carefully tested and is designed for a long service life.

• It is generally recommended to have the unit inspected

every two years to ensure correct functioning and accuracy. Please consult your authorised OMRON dealer or the OMRON Customer Service at the address given on the packaging or attached literature.

• The unit should be cleaned with a soft, dry cloth.

• Use a soft, moistened cloth and soap to clean the arm

cuff.

Automatic Blood Pressure Monitor ProLogic PL100 (HEM-7101-PR) LCD Digital Display Oscillometric method Pressure: 0 to 299 mmHg Pulse: 40 to 180/min. Pressure: ±3 mmHg Pulse: ±5% of display reading Automatic by electric pump Automatic pressure release valve 4 “AAA” batteries 1.5V (not included) Capacity of new alkaline batteries is approx. 300 measurements

= Type B Internally powered ME equipment +10°C to +40°C / Maximum: 30 to 85% RH

-20°C to +60°C / Maximum: 10 to 95% RH / 700-1060hPa Approximately 315g without batteries

Approximately 120g Approximately 103 (w) mm × 62 (h) mm × 125 (l) mm Approximately 146 mm × 446 mm (Medium cuff: arm circumference 22 to 32 cm) Nylon and polyester Main unit, cuff, instruction manual

1. Unplug the air tube from the air jack.

2. Gently fold the air tube into the arm cuff.

4.4 Storage

Note: Do not bend the air tube excessively.

Do not store the unit in the following situations:

• If the unit is wet.

• Locations exposed to extreme temperatures, humidity, direct sunlight,

dust or corrosive vapours.

• Locations exposed to vibrations, shocks or where it will be at an

angle.

Product Description Model Display Measurement Method Measurement Range

Accuracy Inflation

Deflation Power Source Battery Life

Applied Part Protection Against

Electric Shock Operating temperature/ Humidity Storage temperature/ Humidity Console Weight Cuff Weight Outer Dimensions Cuff Dimensions

Cuff Material Package Content

• This device fulfils the provisions of EC directive 93/42/EEC (Medical Device Directive).

• This blood pressure monitor is designed according to the European Standard EN1060, Non-invasive sphygmomanometers Part 1: General Requirements and Part 3: Supplementary requirements for electromechanical blood pressure measuring systems.

• This OMRON product is produced under the strict quality system of OMRON HEALTHCARE Co. Ltd., Japan. The Core component for OMRON blood pressure monitors, which is the Pressure Sensor, is produced in Japan.

Manufacturer

OMRON HEALTHCARE Co., Ltd.

53, Kunotsubo, Terado-cho, Muko, Kyoto, 617-0002 JAPAN

OMRON HEALTHCARE UK LTD.

Opal Drive, Fox Milne, Milton Keynes MK15 0DG, U.K.

OMRON (DALIAN) CO., LTD.

Dalian, CHINA

Distributed by

Production Facility

OMRON HEALTHCARE EUROPE B.V.

Scorpius 33, 2132 LR Hoofddorp THE NETHERLANDS

EU-representative

Medium Arm Cuff

Arm circumference 22 - 32 cm

CM2-9513256-6 (Model: HEM-CR24)

Large Arm Cuff

Arm circumference 32 - 42 cm

CL2-9513255-8 (Model: HEM-CL24)

Error Display Cause Remedy

Cuff is under inflated.

Carefully read and repeat the steps listed under section 3.3.

Movement during measurement.

Repeat measurement. Remain still and do not talk during measurement.

Air plug disconnected.

Insert the air plug securely. Refer to section 3.1.

Arm cuff not applied correctly.

Apply the arm cuff correctly. Refer to section 3.1.

Clothing is interfering with the arm cuff.

Remove any clothing interfering with the arm cuff.

Air is leaking from the arm cuff.

Replace cuff with new one.

Arm cuff has been inflated above 299 mmHg.

Do not inflate the arm cuff above 299 mmHg. Refer to section 3.3.

Battery power is low.

Replace all four “AAA” batteries with new ones. Refer to section 2.1.

Device error.

Contact your OMRON retail outlet or distributor.

Blinks or appears continuously

Arm cuff deflates too soon.

The arm cuff is loose.

Apply the cuff correctly so that it is firmly wrapped around the arm. Refer to section 3.1.

Cannot measure or readings are too low or too high.

The arm cuff has not been inflated sufficiently.

Inflate the cuff so that it is 30 to 40 mmHg above your previous measurement result. Refer to section 3.3.

The unit loses power during measurement.

The batteries are empty.

Replace the batteries with new ones.

Nothing happens when you press the buttons.

The batteries are empty.

Replace the batteries with new ones.

The batteries have been inserted incorrectly.

Insert the batteries with the correct (+/ -) polarity.

ProLogic PL100 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual