Pro-Link 115532 User Manual

SHINING CRYSTALLIZER CR-3

MATERIAL DATA SHEET

1. Product and manufacturer's identification.

Description of the product : SHINING CRYSTALLIZER CR-3.

Use : Product for the regular maintenance of crystallization on marble and
terrazzo paments.

Company : ABRASIVOS AGUILA S.A.
Riera de Palau, 13
08740-Sant Andreu de la Barca
Barcelona ( SPAIN )

Telephone.: [phone] Fax.: [phone]

2. Composition/information about components.

Name Concentration interval Symbol Risk fases

MAGNESIUM FLUOSILICATE 15-30 % T R 25

3. Indentification of danger.

- Harmful for ingestion and external contact.

-A long exposure may cause irritation in mucous membrane and skin.

4. First aids.

Inhalatión : Take the subject away from the contaminated zone and make him
breath fresh air.

Contact with eyes : Wash immediately with water (15 min.), separating the
eyelids. Consult with an ophthalmologist if the irritation continues.

Contact with skin : Take the dirty clothes away. Wash it with soap and water
and rinse with clean water.

Ingestion : Rinse the mouth out. Consult with a doctor.

Precaution : In case of poisoning or accident, it is recommendable to go to an
urgency hospital, since its ingestion can produce a serious hypocalcemia.

SHINING CRYSTALLIZER CR-3

5. Measures of security against fires.

Non inflammable or explosive product.

6. Measures to take in case of accidental spill.

Spread some sand and recover the product in a container for a later
destruction.

Avoid to pour out in the waste pipes, subterranean waters and drains.

Avoid the contact with the environment throug filtrations or contact with the
vegetation.

7. Handling and storage.

Air the premises during the handling. Use gloves and suitable protection.

Keep at temperature of no more than 30ºC, in a ventilated and dry place,
protected from the sunlight, heat sources or focus of ignition.

8. Controls of exposure and personnal protection equipment.

Repiratory protection. Not required for usual workings.
Protection of hands. Use always protective gloves.
Protection of eyes. Use protective glasses.
Protection of skin. Change the dirty or sprikle clothes.

9. Chemical-physical properties.

Aspect : Yellow liquid. Resistance to the temperature :
to the cold : + 1ºC
Density : 1.000 gr/cc. to the heat : + 45ºC

Soluble in water. pH : 2-3

10. Stability and reactivity.

The product does not descompose or change its stability if it is appropiately
storaged.

SHINING CRYSTALLIZER CR-3

11. Toxicological information.

Irritating for skin, eyes, mucous membrane and digestive tract.

12. Ecological information.

Do not pour out in drains or in the environment. It has to be eliminated in an
authorized point of waste collection.

Toxic components for the environment : Fluosilicato de magnesio and
Phosphoric acid.

13. Considerations concerning to the elimination.

Follow the valid regulations for the elimination of chemical wastes.

Avoid always to pour out in residual water pipes.

14. Information concerning to the transport.

This product is not considered as dangerous for transport.

15. Statutory information.

It has to be marked, according the present Spanish regulations :

ABRASIVOS AGUILA S.A.
SHINING CRYSTALLIZER CR-3

SYMBOL OF HARMFUL
SYMBOL OF CORROSIVE

It contains Magnesium Fluosilicate .

Harmful for ingestion. R 25
It causes burns. R 35
It irritates eyes and skin. R 36/38
Keep away from children. S 2
Keep the container well closed. S 7
Keep away from food, drinks and fooders. S 13
Avoid the contact with eyes and skin. S 24/25
In case of contact with eyes, wash immediatly with much water
and go to the doctor. S 26

SHINING CRYSTALLIZER CR-3

In case of contact with skin, wash immediatly with much water. S 28.
In case of accident or unwell, go to the doctor immediately (show him the label
if possible). S 45
In case of ingestion go to a doctor immediately and show him the
label or the container. S 46

16. Other informations.

Aplications of the product :

Special product for the regular maintenance of business premises. Quick
application product. Recommended for white colour marbles. Do not use on
metallic, aluminium, wood, ceramic, and thermoplastic parts. Keep in the
original container.

INSTRUCTIONS FOR USE .

The surface has to be clean and dry.
Shake the container strongly before using.
Do not dilute or mix with other products.
Pour a little quantity of CR-3 on a surface of about 2 m2., spread the product
uniformly with a shining machine equipped with fine steel wool and rub until
the product gets completely dry. Repeat the same so many times as necessary.