60W Tri Par 64
User Manual
Code: ELUM101
1
2
Overview:
You should nd inside the Elumen8 carton the following items:
1, LED 60W Tri Par 64 2, Instruction manual
Technical Specications:
DMX channels: 3 or 5 selectable
1 x 60W Tri LED
Static, sound active, master/slave and DMX modes
2 dimmer curves
400Hz refresh rate
3-pin XLR in/out sockets
4 push button menu with LCD display
Beam angle: 60 degrees
Power supply: 110-240V-50/60HZ
Power consumption: 86W
Dimensions: 390 x 240 x 195mm
Weight: 2.6Kgs
Operating modes: 1, Dimming 0-100%
2, DMX
3, Master/slave
4, Channel select
5, Dimming curves
Overview:
Fuse
Power Supply
3
DMX IN
lcd display
DMX occupation:
1: Ground
2: signal (-)
3: Signal (+)
DMX OUT
MODE ENTER UP DOWN
Operation:
Built-in programmes:
To activate the units built-in programmes, press the “MODE” button to show “01.STATIC” on the LCD screen.
Press the “ENTER” button to choose between the 4 built-in programmes by using the “UP” and “DOWN”
buttons. Now press the “ENTER” button to select the desired speed and adjust by using the “UP” and
“DOWN” buttons. Press the “ENTER” button once more to select the desired ash value and adjust by using
the “UP” and “DOWN” buttons.
Speed values: 00 - 99 (00 = slow, 99 = fast)
Flash values: 00 - 99 (00 = slow, 99 = fast)
Programme 1 - Static colour
In this mode you can set the 60W Tri Par to any colour and any brightness.
When you are in the “01.STATIC” mode, press the “ENTER” button to change the brightness of each
individual colour.
The “R” represents Red, “G” = Green, “B” = Blue and “F” = strobe.
The two digits after it are the brightness 00 to 99 or in “CF” they are the strobe speed.
Example: If you set R, G, and B all to zero, the 60W Tri will have no LEDs showing (blackout).
If you set R to 99 and G, and B to zero the 60W Tri will be 100% Red.
Programme 2 - 7 colour change
In this mode the 60W Tri Par will run through its 7 preset colours.
Programme 3 - 3 colour change
In this mode the 60W Tri Par will run through its 3 colours.
Programme 4 - colour fade
In this mode the 60W Tri Par will fade through its 7 preset colours.
2. Dimmer Response
Press “MODE” until you get to “Dimmer Response”, press the “ENTER” button and use the “UP/DOWN”
buttons to choose between Dimmer Response 01 or 02.
01 = Dimmer curve linear response LED
02 = Dimmer curve linear response Halogen
3. DMX Channel Mode
Press the “MODE” button until “Channel” is shown on the LCD display. Press the “ENTER” button and use
the “UP/DOWN” buttons to select between 3 and 5 channel modes.
4. Slave Mode
To activate the unit in slave mode, rst you must link multiple units together and press the “MODE” button to
show “SLAVE MODE” on the LCD screen. Now on the master unit press the “MODE” button to select the
desired mode and the slave units will now run in sequence with the master unit.
5. Sound Active Mode
To activate the units sound active mode, rst press the “MODE” button until the “SOUND SENS” is displayed.
Press “ENTER” and use the “UP/DOWN” buttons to change the amount of sensitivity between 00 and 31.
6. DMX Mode
To enter the DMX mode, press the “MODE” button to show “DMX MODE” on the LCD display. Now press the
“ENTER” button and use the “UP” and “DOWN” buttons to select the DMX address from 001-512.
When you are happy with your setting, press the “ENTER” button to conrm it.
4
DMX Charts
3 channel mode:
5 channel mode:
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent xtures
and controllers. A DMX controller sends DMX data instructions form the controller to the xture. DMX data is
sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT” XLR terminals located
on all DMX xtures (most controllers only have a data “out” terminal).
DMX Linking:
• DMX is a language allowing all makes and models of different manufactures to be linked together and operate
from a single controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data
transmission, when using several DMX xtures try to use the shortest cable path possible. The order in which
xtures are connected in a DMX line does not inuence the DMX addressing. For example; a xture assigned
to a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the
middle. When a xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to
address 1 to that unit, no matter where it is located in the DMX chain.
DATA Cable (DMX cable) requirements (for DMX operation):
• The 60W Tri Par 64 be controlled via DMX-512 protocol. The DMX address is set on the back of the unit. Your
unit and your DMX controller require a standard 3-pin XLR connector for data input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
5
Channel Value
0-255
0-255
0-225
CH1
CH2
CH3
Function
Red 0-100%
Green 0-100%
Blue 0-100%
Channel
CH1
CH2
CH3
CH4
CH5
Value
0-255
0-255
0-255
0-255
0-255
Function
Red
Green
Blue
Master Dimming 0-100%
Strobe Slow-Fast
Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield conductor
to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the
shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of erratic behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
6
www.elumen8.co.uk
Loading...