How it Works
projectiondesign
Loading...
F85 WUXGA
Product Sheet
2 pgs435.86 Kb0
User Manual
44 pgs6.53 Mb0

projectiondesign F85 WUXGA, F85 1080p User Manual

Download
an introducon to the
an introducon to WQXGA projector
the projector
F85 user’s guide
Designed and manufactured in Fredrikstad, Norway.
user’s guide
www.projectiondesign.com
2UF85 user’s guide - IntroductionF85 user’s guide - Introduction
1 Contents of this User’s Guide
1 Introduction 5
1.1 Thank you
2 SAFETY 7
2.1 SAFETY
2.2 WARNINGS
2.2.1 INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES RELATED TO MERCURY VAPOR
2.2.2 SERVICE PERSONNEL INFORMATION WARNING
2.2.3 REMOTE CONTROL WARNING
2.2.4 WARNING SYMBOLS
2.3 FCC
2.4 WEEE INFORMATION
2.5 RECYCLING
2.6 SERVICE INFORMATION
3 What’s in the box? 11
4 Getting to know the projector 13
4.1 Overview
4.2 Indicators
4.2.1 The status indicator
4.2.2 Keypad
4.2.3 Remote control
4.2.4 Connectivity
4.2.5 Graphical User Interface (GUI)
5 Basic setup 19
5.1 Lens
5.1.1 Lens and lens mount
5.1.2 Inserting a lens
5.1.3 Replacing a lens
5.2 Adjusting on screen image size and position
5.3 Lamp operation
5.4 Projector rotation
5.5 Ceiling mount
5.6 Connection and cables
5.6.1 Setting up a video source
5.6.2 Setting up a computer source
5.6.3 Connecting command and control interfaces
3
www.projectiondesign.com
5.6.4 Attaching X-PORT™ modules
5.7 Using X-PORT™ modules
5.8 Image alignment
5.9 Setting image orientation
5.10 Using source scan
5.11 Limiting OSD messages
5.12 Changing the language of the menu system
5.13 Identifying system status
5.13.1 Getting information about the active source
5.14 Image sizes
6 Advanced setup 29
6.1 Controlling multiple projectors with remote control ID (RCID)
6.2 Protecting the projector with a pin code
6.3 Using dual head input
6.4 Setting custom color space and digital level
6.5 Disabling IR receivers
6.6 Controlling screens with triggers
6.7 Setting aspect trigger behavior
6.8 Automatic power on/off
6.8.1 Using the timer
6.8.2 Using DPMS (Display Power Management Signaling)
6.9 Disabling LED indicators
6.10 Setting the background color
6.11 Setting OSD menu timeout
6.12 Selecting the startup logo
7 Optimising the picture 33
7.1 Calibration data
7.1.1 Updating RealColor™ calibration data
7.1.2 Gamma
7.1.3 RealColor™ operating modes
7.1.4 Setting a white point or color temperature
7.1.5 Defining the system color gamut
8 Maintenance 39
8.1 Software upgrades
8.2 Lamp replacement
9 Technical specifications 41
9.1 Product details
User’s Guide – Introduction
F85 user’s guide – Introduction
4

1 Introduction

1.1 Thank you

Thank you for purchasing this projector.
The F85 digital projector is designed with the latest state-of-the-art technologies in illumina­tion, imaging, optics, electronics, thermal and industrial design in order to serve traditional as well as novel imaging applications across a variety of markets.
Features
• Full HD 1080p, WUXGA or SXGA+ resolution, 3-chip DLP® technology
• Patented Dual ArchTM illumination system and optics
• RealColor advanced color management suite
• Fail safe, dual lamp architecture
• Optomechanical IRIS for customizable brightness and contrast
• Powered horizontal and vertical lens shift, allows direct stacking
• Full 10-bit color resolution for minimised artefacts and image fidelity
• Elevated contrast levels for unmatched image dynamics
• Dynamic Black for improved video contrast
• Advanced optical color processing
• Wide range of projection lenses
• Highly versatile color management and calibration options
• Built-in real time clock for timed operations/events
• Economy mode for reduced power consumption and prolonged lamp life
• Compact 3-chip design
• Direct view status LCD and lamp function indicators
• Multiple video and graphics inputs for virtually any video and data source
• HDMI ver. 1.3a
• LAN and RS232 ports for control and monitoring
• Dual X-PORT functionality allows additional inputs and signal processing
Symbols used in this documentation
WARNING: Used to point out potential danger to people or equipment when using this product or peripheral equipment.
NOTE: Used to point out essential handling requirements for the projector, which if not acted on may cause product malfunctioning.
TIP: Used to give advice which benefits the projector usage or conditions related to projector performance.
The specifications and functionality of this projector may change without prior notice
5
www.projectiondesign.com
User’s Guide – Introduction
F85 user’s guide – Introduction
6
2 SAFETY
This device complies with safety regulations for Information Technology Equipment for use in an office environment. Before using the device for the first time, please read the safety instructions thoroughly.
2.1 SAFETY
This user guide contains important information about safety precautions and the set-up and use of the projector. Please read the manual carefully before you operate the projector.
2.2 WARNINGS
Use only the cables and cords supplied with the projector or original replacement cables. Using other cables or cords may lead to malfunction and permanent damage of the unit.
Always use 3-prong / grounded power cord to ensure proper grounding of the unit. Never use 2-prong power cords, as this is dangerous and could lead to electrical shock.
Never open the unit. The projector contains no user serviceable parts. Refer all repairs to qualified personnel only. Make sure that no objects enter into the vents and openings of the set.
Do not spill any liquids on the projector or into the vents or openings of the unit.
Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens.
Do not look into the projection lens when the projector is switched on. The strong light may permanently damage sight. Do not look into the laser beam when activated on the remote control. Laser light may per­manently damage sight. Do not point laser beam at people or animals.
Only place the projector on a stable surface, or mount it securely using an approved ceiling­mount secured to a suitable construction. For stacking, maximum two projectors may be stacked. See detailed instructions in separate installation guide.
Do not drop the projector.
Always operate the projector according to the rotation guidelines. Operating the unit in other positions may reduce lamp life significantly, and may lead to overheating, resulting in malfunctioning.
Always allow ample airflow through the projector. Never block any of the air vents. Never cover the unit in any way while running. Allow for sufficient distance to walls and ceilings to avoid overheating.
Minimum safety distance to any side of the unit whith ventilation slots is 60 cm / 24”.
Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than 60 cm / 24” to the exhaust vent.
The projector is designed for indoor use only. Never operate the unit outdoors.
Do not operate the projector outside its temperature and humidity specifications, as this may result in overheating and malfunctioning.
Connecting sources to a powered projector may result in product failure. It is recommended that the power cable connector (projector-end) or the mains power socket are accessible whilst the product is in use to enable mains power to be discon­nected or switched off when connecting source devices. This should be considered during product installation.
7
www.projectiondesign.com
Only connect the projector to signal sources and voltages as described in the technical specification. Connecting to unspecified signal sources or voltages may lead to malfunction and permanent damage of the unit.
In order to prevent damage to the projector caused by overvoltages (e.g. lightning), we rec­ommend connection to a line (mains) circuit which has overvoltage protection.
Allow unit to cool down for 60 minutes before changing the lamp. USE ONLY ORIGINAL LAMPS.
2.2.1 INFORMATION AND WARNING ABOUT POTENTIAL HEALTH ISSUES RELATED TO MERCURY VAPOR (UHP lamps only)
This projector uses a very powerful UHP™ lamp for illumination to produce an extremely bright image.
This technology is similar to other high-pressure discharge lamps that are extensively used in cars, street lights and other lighting appliances today. These lamps, like fluorescent lighting, contain small amounts of mercury. The amount of mercury present in a lamp is far below the limits of danger set by the authorities. It is very important that lamps containing mercury are treated properly to minimize potential health hazards.
The UHP™ lamp, like any other high brightness projector lamp, is under high-pressure when operating. While the lamp and the projector are carefully designed to minimize the prob­ability of lamp rupture, the lamp may break while operating and small amounts of mercury vapor may be emitted from the projector. The probability of rupture increases when the lamp reaches its nominal life. It is therefore highly recommended that the lamp is replaced when the rated lifetime is reached.
As a general precaution, secure good ventilation in the room when operating the projector. If lamp rupture occurs, evacuate the room and secure good ventilation. Children and pregnant women in particular should leave the room.
When replacing a worn lamp, dispose of the used lamp carefully by proper recycling.
Mercury is a naturally occurring, stable metallic element that may pose a safety risk to people under certain conditions. According to the Public Health Statement for Mercury published by the Agency for Toxic Substances and Disease Registry (“ATSDR”, part of the United States Public Health Service), the brain, central nervous system and kidneys are sensitive to the effects of mercury, and permanent damage can occur at sufficiently high levels of exposure. Acute exposure to high concentrations of mercury vapor can cause conditions such as lung and airway irritation, tightness in the chest, a burning sensation in the lungs, coughing, nausea, vomiting and diarrhea. Children and fetuses are particularly sensitive to the harmful effects of metallic mercury to the nervous system.
Seek medical attention if any of the above symptoms are experienced or if other unusual conditions are experienced following lamp rupture.
2.2.2 HEAVY DUTY AND CONTINOUS USE (UHP lamps only)
The projector contains moving parts (such as cooling fans) that have limited life-expec­tancies. When the projector has been used for 8 000 hours, and when the unit is used in mission-critical applications, it is recommended that the projector is given preventive mainte­nance by a qualified service person. A message will appear on the screen when the projector is due for preventive maintenance. This will help ensure long term stable operation.
2.2.3 SERVICE PERSONNEL INFORMATION WARNING (UHP lamps only)
Use UV radiation eyes and skin protection during serviceing.
8User’s Guide - SAFETYF85 user’s guide - SAFETY
2.2.4 REMOTE CONTROL WARNING
Laser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN/IEC 60825-1/2007
Use of controls or adjustments, or performance of procedures other than those specified in the User Guide, may result in hazardous radiation exposure.
2.2.5 WARNING SYMBOLS
Here is a list of warning symbols found on the product lable(s):
READ USER GUIDE Attention! Read the user guide for further information!
DANGEROUS VOLTAGE Danger! High voltage inside the product!
HOT Warning! Hot surfaces!
WAIT Warning! Wait until cooled down!
MERCURY Warning! Lamp contains mercury! Recycle properly,
do not dispose of in ordinary waste!
UV Warning! UV radiation inside the product!
RECYCLE Warning! Recycle properly, do not dispose of in ordinary waste!
2.3 FCC
FCC regulations provide that changes or modifications not expressly approved by the party responsible manufacturer could void your authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
CANADA
This Class A digital apparatus complies with Canadian ICES-003. / Cet appareil numérique de la classe A est conforme à la norme NMB- 003 du Canada.
WARNING This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
9
www.projectiondesign.com
2.4 WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste electrical and elec­tronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to facilitate proper recycling of it’s individual parts. This product is using projection lamps that shall be recycled properly. Consult your dealer or relevant public authority regarding drop-off points for collection of WEEE.
2.5 RECYCLING
This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Recycle properly, do not dispose of in ordinary waste!
2.6 SERVICE INFORMATION
This product contains no user serviceable parts. If the product fails to function as expected, please first check that all connections are properly made, and that the power cord is properly connected. Please check that the projector as well as the video and computer sources are all switched on. Cables and cords may break over time. Try to change cables and cords, in case there is a bad or intermittent connection. Check if the circuit breaker or fuse of your mains is intact. In the event of product failure, please contact your reseller. You should prepare a description of the symptoms of failure you experience. Please also state product number and serial number as printed on the label on the side of the projector.
10User’s Guide - SAFETYF85 user’s guide - SAFETY
3 What’s in the box?
The following components are standard delivery:
Projector
Power Cable (Country Dependant)
Remote Control
User Documentation
Please verify that you have all compoents upon unpacking the unit, and its contents. Check next page for additional accessories.
Please save packaging materials for future use, should it be necessary to ship the unit.
11
www.projectiondesign.com
Additional accessories available for the projector:
HDMI-cable (2m)
DVI-cable (2m)
Stacking Set
F85 user’s guide - What’s in the box?
12User’s Guide - What’s in the Box?
4 Getting to know the projector
4.1 Overview
A Lens
B IR sensor
C1 Ventilation - Air flow IN
C2 Ventilation - Air flow OUT
D Lens release
E Power connector
F Keypad
G Connector panel
H LCD
I Lamp lids
J Adjustable stacking-
and levelling feet
K Adjustment screws for
stacking- and levelling feet
L Security lock
M Ceiling mount
AB D E C
Figure 4-1. - Projector front view
J
1
13
F
I
B
Figure 4-2. - Projector rear view
J
K
L
Figure 4-3. - Projector bottom view
H
G C
M
2
K
* Features in the user guide pictures/drawings may
B
be different from your projector depending on model/ version.
www.projectiondesign.com
4.2 Indicators
System status indicators are located to the right of the keypad on the back of the projector. Figure 4-4 shows the three status indicators – one for each lamp and one for the system status.
Figure 4-4. The lamp indicators
For the lamp indicators the following apply:
- PERMANENT GREEN LIGHT: The lamp is on and operating normally.
- PERMANENT YELLOW LIGHT: The lamp is off. The lamp may be disabled in the menu or the system is in standby.
- PERMANENT RED LIGHT: Lamp life has expired, lamp is not igniting or lamp door is open. If the lamp life has expired, please change projection lamp immediately. Failing to change lamp may lead to lamp explosion. Please replace with original projectiondesign replacement lamp.
- FLASHING YELLOW LIGHT: The lamp is cooling down. The total cooling down time is approximately 45 seconds.
- NO LIGHT: No lamp inserted.
The replacement lamps must be purchased from an authorized projectiondesign
dealer for the warranty of the product to be valid. Using lamps from any other after market supplier will void the warranty.
4.2.1 The status indicator
- PERMANENT GREEN LIGHT: The projector is turned on and in normal operation.
- PERMANENT YELLOW LIGHT: The projector is in standby mode. If the projector was powered off by the power saving feature (DPMS), it will automatically power on when you connect a valid source.
- FLASHING YELLOW LIGHT: Please wait. The yellow light will flash a period after power cord is connected (20-30 sec.), and a period after going to standby mode while lamp is cooling down (approximately 45 sec.). The projector may not be turned on again until the light has turned to permanent yellow.
- FLASHING RED LIGHT: Projector is overheated. Turn off immediately! Check if air inlets are covered or if ambient temperature is outside specifications. The projector cannot be restarted until the power cord is disconnected and reconnected again. If the projector continues to flash red, you will need to return the unit for service.
F85 user’s guide - Getting to know the projector
User’s Guide – Getting to know the projector
14
4.2.2 Keypad
Figure 4-5. Projector keypad
The projector has an illuminated keypad on the back of the unit. Figure 4-5 shows the keypad.
The keypad is used to:
- navigate the menu system
- scroll the information in the LCD panel
- directly select input sources
- enter pin code (if enabled)
- power on/off
- adjust basic image functions
The keypad is illuminated for operation in dark environments. Available functions are illuminated in yellow while selected (active) functions are illuminated in green. Functions that are not available are not illuminated.
4.2.3 Remote control
The remote control allows flexible access to the projector settings, either through direct keys, or through the menu system. The remote control is backlit for use in dark environments. It also has a data-jack that allows for wired connection to the projector. When the wire is connected, the IR (infra-red) beam and internal batteries are switched off.
Figure 4-6. Remote control
Do not look into the laser beam when activated on the remote control. Laser light may permanently damage eyesight. Avoid pointing the laser beam at people or animals.
Only use the supplied remote control, otherwise the result may be malfunction.
15
www.projectiondesign.com
4.2.4 Connectivity
The projector features a wide range of video inputs and command/control connectors. Figure 4-7 shows the connector panel.
A
D
E
F
B
Figure 4-7. Connector panel
A LAN: 10/100 Mbit Ethernet connector for command, control and software upgrade.
B RC INPUT: 3.5mm mini-jack connector. Allows connection of external IR receiver or
wired remote control.
C TRIGGERS: 3.5mm mini-jack connector triggers. Used for controlling peripheral
equipment like motorized screens.
D 3D SYNC: For 1080/WUXGA 3D projectors used to attach external ir-glass emitters
E RS-232: Allows for wired remote control and monitoring of many projector functions
used in installation environments.
F USB-A: Allows for software upgrades using a standard USB memory stick.
G USB-B: Reserved for future use.
H SYNC-IN: Allows for taking an external vertical sync signal and using that with the select
video input. This is mainly used in multiple projector installations with requirement of video synchronization between the units.
I SYNC-OUT: Constantly outputs the vertical sync signal of the active video input. This
is mainly used in multiple projector installations with requirement of synchronization between the units.
J DVI-D: Two Dual Link DVI-D connectors with bandwidth up to 330 Mhz total. These
connectors can also be used to form one uniform image by feeding half of the image into each connector. HDCP compliant for sources up 165 Mhz.
K VGA: Two VGA connectors with bandwidth up to 170 Mhz
L YPbPr: Analog video input supporting YPbPr and RGB (sync-on-green) video standard
up to 1080i.
M HDMI 1.3: Two HDMI 1.3a connectors with bandwidth up to 165 Mhz each. These
connectors can also be used to form one uniform image by feeding half of the image into each connector. HDCP compliant. All video formats specified by the HDMI 1.3a are supported.
C
G
H
J
K
L
M
I
F85 user’s guide - Getting to know the projector
User’s Guide – Getting to know the projector
16
4.2.5 Graphical User Interface (GUI)
The projector has an easy-to-use on screen display (OSD) system for controlling the extensive number of features implemented. Figure 4-8. Top level OSD menu, shows the top level of the OSD menu.
Figure 4-8. Top level OSD menu
Activate the menu by pressing the “MENU” button on either the keypad or the remote control. Navigate the menu using the arrow keys.
The various functions in OSD menu is described in Chapter “5 Basic setup”.
The top level menu item 3D is only visible for Active Stereo 3D enabled projectors (1080p and WUXGA).
17
www.projectiondesign.com
F85 user’s guide - Getting to know the projector
User’s Guide – Getting to know the projector
18
5 Basic setup
5.1 Lens
5.1.1 Lens and lens mount
A range of fixed and zoom lenses is available to cover most applications, both front and rear. The lenses are powered and fitted with a bayonet mount for ease of installation.
Switch off all equipment before setting-up for proper function.
When mounting and changing lenses, be aware that the optical system is exposed to dust and foreign particles as long as the lens is not attached to the system. Do not leave the lens mount open longer than necessary to change lens. If a lens is not mounted, always insert the protection lid to avoid dust and foreign particles entering the internal optics.
Never run the projector without lens mounted.
5.1.2 Inserting a lens
To insert a lens please follow this procedure:
A Remove the protection lid from the bayonet mount by
turning the knob anti-clockwise.
B Remove the rear lens cap.
C Attach the projection lens using the bayonet mount,
observing the red insertion marks.
D Turn the lens firmly clockwise until it stops with a click.
E Remove the lens cap from the projection lens. If you
switch the projector on with the lens cap in place, the lens cap may melt, damaging not only the lens cap, but also the projection lens and surrounding parts.
5.1.3 Replacing a lens
To replace a lens please follow this procedure:
F To change lens, first remove the current lens by
pushing the release button and twisting the lens counter-clockwise until it comes loose. Pull the lens out.
G Insert the new lens as described in above.
D
C
A
B
CLICK
19
G
F
E
www.projectiondesign.com
5.2 Adjusting on screen image size and position
Adjusting the placement of the image on screen can be done using the:
1. Adjustable feet (E in Figure 5-1).
2. Lens shift mechanism controlled from the keypad, the remote control, RS-232 or LAN (A
in Figure 5-1).
3. Zoom (for lenses with zoom) in the lens controlled from the keypad, the remote control,
RS-232 or LAN (B in Figure 5-1).
After the correct image size and position is found, please adjust the image focus using the keypad, the remote control, RS-232 or LAN. (4 in Figure 5-1).
1
Figure 5-1. Image size ans position adjustment
5.3 Lamp operation
The projector is fitted with two individual projection lamps that can be run in various modes. In addition, lamps can be replaced as needed separately. This ensures an optimized cost of ownership. Individual lamp timers are maintained for each lamp.
Lamp operation mode is controlled in the INSTALLATION > LAMPS sub menu.
3 4
2
20User’s Guide - Basic setupF85 user’s guide - Basic setup
5.4 Projector rotation
Always operate the projector horizontally, within the range of the adjustable front and rear feet. The projector may be rotated so that the lens points downwards. It may not be rotated around the through-the-lens axis.
Operating the unit in other positions may reduce lamp life significantly, and may lead to overheating, finally resulting in malfunctioning.
5.5 Ceiling mount
The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount fixture, with a capacity of minimum 160 kg / 353 lbs. For ceiling mount use M6 screws that penetrate maximum 12 mm / 0.5” into the projector body. Figure 5-3 gives detailed informa­tion about the alignment of the ceiling mount screw holes in the projector.
For proper ventilation the minimum distance from ceiling/ rear wall should be: 30 / 60 cm, 12 / 24 inch.
167
164
83.5
4
604
LENS RELEASE
PUSH AND HOLD
249355
Figure 5-2. Ceiling mount
0.4
501
158.2
115
250
135
21
www.projectiondesign.com
5.6 Connection and cables
Before setting up, switch off all equipment and disconnect the power cord.
In order to prevent damage to the projector caused by overvoltages (e.g. lightning), we rec­ommend connection to a line (mains) circuit which has overvoltage protection when installing.
5.6.1 Setting up a video source
For best quality video, connect a digital video source using the HDMI 1.3a interface (O), see Figure 5-3. The HDMI input is HDCP copy protection compliant. Depending on cable quality, the projector is supporting the use of cables with lengths up 20 meters (65 feet).
Figure 5-3. Connecting a video source
5.6.2 Setting up a computer source
The projector may be connected to up to six computer sources simultaneously, using the HDMI (O), DVI-D (J) or VGA (K) interfaces, shown in Figure 5-3/Figure 5-4. The digital inter­faces (DVI/HDMI) will yield a projected image with very low noise.
Both DVI and HDMI are HDCP compliant with sources up to 1920x1200@60Hz (single link source up to 165 Mhz). Additional functionality may be acchieved using additional X-PORT connectors like 3G-SDI, DisplayPort 1.1a and HDMI 1.4a (se separate sections).
Figure 5-4. Connecting a computer source
HDCP is not supported on higher resolution sources like 2560x1600@60Hz (WQXGA).
Connect the power cord after the other cables have been inserted properly.
5.6.3 Connecting command and control interfaces
The projector is supporting RS-232 and LAN command and control interfaces. Use the ASCII based, simple instruction set (SIS) protocol to communicate with the projector. A detailed description of the ASCII protocol is available for download at www.projectiondesign.com. Connect the power cord after the command and control cables are inserted properly.
Figure 5-5. Connecting command interfaces
22User’s Guide - Basic setupF85 user’s guide - Basic setup
5.6.4 Attaching X-PORT™ modules
X-PORT™ modules are separately available for purchase and not included with the base projector.
Switch off projector and disconnect power cord before attaching X-PORT™ module. Before attaching any X-PORT module, please make sure you have the latest SW run­ning on the projector. Please go to www.projectiondesign.com to download the current SW and update the projector accordingly. See chapter 8 for details on how to upgrade the projector SW.
The projector supports up to two X-PORT™ modules simultaneously:
- X-PORT™ 1 for additional image processing (X-PORT™ DCC120*). Left hand side.
- X-PORT™ 2 for additional connectivity (X-PORT™ 3G-SDI, X-PORT™ DisplayPort 1.1a
and X-PORT™ HDMI 1.4a*). Right hand side.
* X-PORT™ modules subject to availability.
To attach an X-PORT™ module, please follow this procedure:
A Remove cover plate, by removing the four screws.
B Attach module. Observe X-PORT™ 1 and 2 positions are different. Attaching X-PORT™
modules in the wrong position will leave the module non-functional, but it is not destructive.
C Fix the four mounting screws securely.
A
Remove 4 retainer screws
B
Mount X-PORT module
Fasten 4 module screws
C
* Features in the user guide pictures/drawings may be different from your projector depending on model/version.
Finally connect power cord and switch on projector.
The first time after a module is attached, the projector will automatically update and configure the module. This may take a few minutes. Please ensure that power remains on during this period!
23
www.projectiondesign.com
5.7 Using X-PORT™ modules
X-PORT™ modules allows for extra functionality with the projector. This includes more con­nectivity as well as additional image processing.
Functionality may include extended connectivity (like 3G-SDI, DisplayPort 1.1a and HDMI
1.4a) and additional 3D format support (like Blu-Ray frame packed, dual input sources, dou­ble flash 3D etc.)
Please refer to the documentation provided with the individual X-PORT™ modules for further information.
5.8 Image alignment
For easier alignment of the projector, test images are built into the system.
To enable test images, go to the menu entry INSTALLATION > TEST IMAGE. Cycle the vari­ous test images using the arrow keys. When a test image matching the aspect ratio of your screen has been found, use the zoom, focus, lens shift and physical projector alignment to match the screen.
5.9 Setting image orientation
In relation to the screen, the projector supports the following installation orientations:
• Desktop front (default)
• Ceiling front
• Desktop rear
• Ceiling rear
To set the image orientation go to menu entry INSTALLATION > IMAGE ORIENTATION
5.10 Using source scan
The projector can automatically scan through all the input connectors for a valid signal. If a valid signal is found, the image will set up. This is called source scan.
Source scan is default disabled. When disabled, the projector will only search the selected input connector for a valid signal. Use the keypad, remote control or any command and control interface to change in selected input interface.
To set the source scan setting, go to menu entry INSTALLATION > SOURCE SCAN
5.11 Limiting OSD messages
When detecting sources and using the various features of the projector, OSD messages will appear on the screen. Which messages that are appearing can be partially controlled by the user. The OSD can run in these modes:
• ON. All messages, warning and information OSDs are displayed.
• OFF. No messages are shown.
• Only warnings. Only critical warning messages like temperature overheating will be shown.
Go to menu entry INSTALLATION > OSD ENABLE to control the OSD behavior
24User’s Guide - Basic setupF85 user’s guide - Basic setup
5.12 Changing the language of the menu system
The projector menu system has a total of 11 user-selectable languages embedded for easier use all over the world. The default language is English.
The available languages are:
• English
• French
• German
• Spanish
• Russian
• Norwegian
• Swedish
• Korean
• Japanese
• ChineseSimplied
• ChineseTraditional
• Portuguese
• Italian
To change the language of the menu system, just select “LANGUAGE” from the top menu and select your desired language.
5.13 Identifying system status
For ease of use, the projector has a complete menu available for system status. It is easily accessible from the top menu. From this menu the following information can be read:
• Part number
• Serial number
• The year/week the projector was manufactured
• Current software version
• Runtime and remaining time for both lamps
• Total number of operating hours
• All network information
• Current lens mounted
• Currently active source
5.13.1 Getting information about the active source
By selecting STATUS > SOURCE INFORMATION basic information about currently active source is displayed.
If a deeper analysis is required for the currently active source, select STATUS > SOURCE IN­FORMATION > ADVANCED. This menu provides detailed timing information for the currently active source.
25
www.projectiondesign.com
5.14 Configuring 3D (AS3D)
This is information is only applicable to the WUXGA and 1080p versions, not WQXGA.
The projector has support for AS3D. AS3D images require active shutter glasses to work. To enable active stereo select 3D > 3D MODE. Enabling 3D mode will configure the projector for the use with an active stereo source.
The only active stereo 3D format natively supported by the projector is sequential left/ right at a frequency between 100 and 120 Hz. Both DVI and HDMI connectors can be used for sources up to 165 Mhz. For sources between 165 and 330 Mhz, only DVI dual link is supported.
After enabling stereo mode, configure the glass type being used by selecting 3D > 3D GLASSES TYPE. The follow glasses are support:
• DLP Link™
• IR
• IR high brightness (may cause crosstalk)
When using IR glasses it is important to configure the phase delay between the glasses and actual image. This is done using 3D > 3D LOCK PHASE DELAY with values 0 and 179 degrees.
If left/right data channels are swapped there will be no 3D effect in the image, only parallel distortion between the channels. This can be countered by enabling the 3D > SWAP EYES feature.
26User’s Guide - Basic setupF85 user’s guide - Basic setup
5.15 Image sizes
10.0
9.0
8.0
7.0
6.0
5.0
1920 x 1080 / 1920 x 1200 (1080 / WUXGA)
4.0
3.0
2.0
1.0
EN 22 Ultra Wide Angle 0.74 : 1 (0.7 - 10 m)
EN 23 Wide Angle Zoom 1.2 - 1.7 : 1 (1.8 - 15 m)
EN 21 Standard Zoom Lens 1.7 - 2.55: 1 (1.9 - 20 m)
EN 24 Short Tele Zoom 2.5 - 4.0 : 1 (5 - 20 m)
EN 26 Long Tele Zoom 3.9 - 6.24 : 1 (5 - 20 m)
0
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
WUXGA: 118 %
1080: 131 %
SXGA+: 110%
27
WUXGA: 84 %
1080: 85 %
SXGA+: 89%
WUXGA: 84 %
1080: 85 %
SXGA+: 89%
www.projectiondesign.com
10.0
1400 x 1050 (SXGA+)
9.0
8.0
7.0
6.0
5.0
EN 22 Ultra Wide Angle 0.80:1 (0.7 - 10 m)
4.0
3.0
2.0
1.0
EN 23 Wide Angle Zoom 1.30 - 1.84:1 : 1 (1.8 - 15 m)
EN 21 Standard Zoom Lens 1.84 - 2.76:1 (1.9 - 20 m)
EN 24 Short Tele Zoom 2.74 - 4.33:1 (5 - 20 m)
EN 26 Long Tele Zoom 4.22 – 6.76:1 (5 - 20 m)
0
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0
28User’s Guide - Basic setupF85 user’s guide - Basic setup
6 Advanced setup
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When several projectors are in use in an installation, individual control may be convenient. Individual control is available either by wired remote control, using the data-jack, or by using an individ­ual number code. For individual control, first set the individual RC ID code using the projector menu system, see the SETTINGS sub menu. Then, to select a specific projector to control, first press the ‘*’ button in the lower keypad area, then the code as set in the target projector. A code can be in the range ‘0’..’99’. ‘0’ is reserved for broadcast. To select another target, repeat the process by pressing ‘*’ and a new code. To exit individual control, press ‘*’’*’ twice or press ‘*’ and ‘0’.
6.2 Protecting the projector with a pin code
The projector may be controlled by a PIN (Personal Identification Number) code. The PIN code is 4 digits, and if the PIN code is activated, you must enter the correct code to unlock the projector. Factory set PIN (1234).
To activate, deactivate or change the PIN code, see the SETTINGS > PIN CODE sub menu.
If an incorrect PIN code is entered, you may try again two times. If you fail three times in a row, a PUK (unlock) code is needed. The PUK code is supplied with the product.
Entering the puk code correctly is the customers responsibility
If you also fail three times with the PUK code, the projector locks up permanently, and can only be unlocked by a special service unlock code.
To access this code, you will need to contact your dealer or a service station. The service unlock code will be generated based on a secure, encrypted number that is produced by the projector itself. The projector will produce a new number every time.
29
To unlock the projector, proof of ownership must be provided by the customer
www.projectiondesign.com
1 2
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz, the projector is supporting a dual head input mode. In this mode the left and right half of the image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively (Figure 6-1). To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is the only available option at this time.
Figure 6-1. Dual input mode
An example of this is feeding a WQXGA (2560x1600) source with 1280x1600 resolutions on each the DVI interfaces.
When enabling this mode, the EDID data on each of the DVI connectors will automatically be changed from WQXGA (2560x1600) to 1280x1600.
For the image to be displayed in this mode, the resolution must be exactly the same on both connectors.
In this mode the two connected sources must have exactly the same timing. A drift in timing between the inputs will result in a visible split in the center of image.
Some graphic cards have problems with detecting the change from single head to dual head mode. If problems occur, disconnect both signal cables before enabling or disabling the dual mode in the menu.
6.4 Setting custom color space and digital level
The projector will automatically try to set the correct color space and digital drive level based on information from the source.
To manually override the automatically detected color space and digital level go to menu entry PICTURE -> ADVANCED. Set the “digital color space and level” to manual and select your color space and digital drive level.
6.5 Disabling IR receivers
The projector has 3 IR receivers as shown in chapter “4.1 Overview”.
These receivers can be individually disabled if necessary. Go to menu entry INSTALLATION > IR FRONT / IR REAR to disable the receivers.
30User’s Guide - Advanced setup F85 user’s guide - Advanced setup
6.6 Controlling screens with triggers
The projector has two programmable triggers with 3.5 mm mini-jack connectors. These can be used to enable or disable screens, curtains or other peripheral equipment.
To change trigger settings, go to menu entry INSTALLATION > TRIGGER
By default:
• Trigger 1 is set to control a screen depending on whether projector is powered on or not.
• Trigger 2 is set to control a screen depending on the aspect ratio of currently active
source.
Both triggers can be manually overridden both in the menu system and by using the com­mand and control protocol through RS-232 or LAN.
6.7 Setting aspect trigger behavior
To customize the aspect trigger functionality, go to menu entry INSTALLATION > TRIGGER > ASPECT TRIGGER BEHAVIOR. In this sub-menu it is selectable for which input aspect ratios the trigger will be enabled.
6.8 Automatic power on/off
The projector can be automatically powered on or off by using the internal timer function or DPMS.
6.8.1 Using the timer
The projector features a real-time clock that enables timing control. This means that the projector can be programmed to switch on and off at certain pre-set times during a weekly cycle.
To allow for a flexible schedule, 10 ‘programs’ are available. With each program, you can define the switch on or switch off time for a single day (Monday to Sunday), all work days (Monday through Friday), or week-end (Saturday and Sunday). One, several or all programs can be active at the same time as desired. In this way, a flexible scheme can be established. Observe the 24 hour time format. For more information, see the SETTINGS > TIMER menu.
The following example illustrates a case where the projector turns on at 08:00 in the morning (8 am) and switches off at 20:00 (8 pm) on weekdays (Monday through Friday). Weekends (Saturdays and Sundays), it turns on at 10:00 (10 am) and off at 18:00 (6 pm). VGA is used as the source. For this, four programs are needed, 2 for on and two for off.
6.8.2 Using DPMS (Display Power Management Signaling)
The projector is enabled for DPMS (Display Power Management Signaling). When enabled, the projector will automatically switch to standby mode after a specified time if there is no valid source present at its inputs. When a valid source is reconnected, the projector will start up again.
To enable or disable DPMS, go to menu entry SETTINGS > DPMS. The desired DPMS time­out is set in the DPMS > DPMS TIMEOUT menu entry.
DPMS is disabled by default.
31
www.projectiondesign.com
6.9 Disabling LED indicators
In certain installations it may desirable to completely disable the LED indicator in the keypad of the projector. To disable the LED indicators, go to menu entry SETTINGS > LED INDICATORS MUTE.
If the LED indicators are enabled, the timeout period can be set in the menu under SET­TINGS > BACKLIGHT TIMEOUT.
6.10 Setting the background color
The background color displayed when the projector is searching for a source can be set to a set of predefined colors. Go to menu entry SETTINGS > BACKGROUND to set the desired color. Default is black.
6.11 Setting OSD menu timeout
If the OSD menu is open and not used for a defined period of time, it will automatically be disabled. The default time is 30 seconds. This timeout interval can be controlled from 5 sec­onds to 60 seconds. The timeout can also be set to “never” for the OSD menu to never time out. Go to menu entry SETTINGS > MENU TIMEOUT to change this setting.
6.12 Selecting the startup logo
When the projector is starting up, a logo is displayed in the entire image. The logo can also be set to “black” if it is desirable to disable the manufacturers default logo. Go to menu entry SETTINGS > SPLASH to change this setting.
32User’s Guide - Advanced setup F85 user’s guide - Advanced setup
7 Optimising the picture
The projector has power features for picture optimization. This chapter describes details in using these features. All color calibration is done using projectiondesign’s proprietary Real­Color™ solution.
7.1 Calibration data
All projectiondesign projectors are measured and calibrated with high precision equipment at the factory for the best out-of-box experience. Over the lifetime of the lamps the characteris­tics of the projector might change slightly. The same applies when replacing lamps.
7.1.1 Updating RealColor™ calibration data
For accurate results with the RealColor™ system, accurate measurement data is required.
RealColor™ calibration data can be found under the menu entry PICTURE > CALIBRATION > REALCOLOR CALIBRATION > MEASURED VALUES
X, Y and relative luminance values for red, green, blue, white is entered in this menu. All val­ues can also be updated using the communications protocol over RS-232 or LAN.
Measurements must be done on the built in test patterns. In the user menu these patterns can be accessed through PICTURE > CALIBRATION > REALCOLOR CALIBRATION > CALI­BRATION TESTIMAGE. Use the arrow keys to cycle through the images.
Performing a factory reset of the projector will restore the measured values to the val­ues measured in the factory.
When measuring data, a high quality measurement instrument is highly recommended for accurate results. Spectrometers (like PhotoResearch PR-655) are preferred.
For an easier calibration procedure, automated calibration can be achieved using projectiondesign’s software package ProNet. A license for the calibration software package of ProNet must be purchased separately.
33
www.projectiondesign.com
Film 2.6
Film 2.6
Film 2.4
Film 2.4
Film 2.2
Film 2.2
7.1.2 Gamma
The projector features a set of 8 built in gamma curves: Film 2.2, Film 2.4, Film 2.6, Film 2.8, Video 1, Video 2, Computer 1, Computer 2. The different gamma curves are displayed below.
The names of the curves are descriptive for their recommended use. Use any of the computer curves for video applications will results in significant image noise.
1,2
1
0,8
0,6
0,4
0,2
0
Figure 7-1. Film 2.2 gamma
1,2
1
0,8
0,6
0,4
0,2
0
Figure 7-2. Film 2.4 gamma
1,2
1
0,8
0,6
0,4
0,2
0
Figure 7-3. Film 2.6 gamma
34User’s Guide – Optimising the pictureF85 user’s guide – Optimising the picture
Video 1 Base
1,2
Video 2 Base
1,2
Film 2.8
1
0,8
0,6
0,4
0,2
0
Figure 7-4. Film 2.8 gamma
1,2
1
0,8
0,6
0,4
0,2
0
Figure 7-5. Video 1 gamma
1
0,8
0,6
0,4
0,2
0
Figure 7-6. Video 2 gamma
35
www.projectiondesign.com
Computer 1 Base
Computer 2 Base
1,2
1
0,8
0,6
0,4
0,2
0
Figure 7-7. Computer 1 gamma
1,2
1
0,8
0,6
0,4
0,2
0
Figure 7-8. Computer 2 gamma
36User’s Guide – Optimising the pictureF85 user’s guide – Optimising the picture
7.1.3 RealColor™ operating modes
Before any color correction is applied to the image, the feature must be enabled. Go to menu entry PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™.
RealColor™ can operate in 3 modes:
• Colortemperature/whitepointcorrectiononly.
• Red,Green,Blue,Whitecorrection.InthismodeoptimalcolorcoordinatesforCyan,
Magenta and Yellow will be computed automatically.
• Red,Green,Blue,Cyan,Magenta,Yellow,White.Inthismodecolorpointsandintensity
for each color can be manipulated separately.
To change the RealColor™ mode, please go the menu entry PICTURE > REALCOLOR > DESIRED VALUES > DESIRED COORDS MODE.
7.1.4 Setting a white point or color temperature
After enabling RealColor™, set the color temperature in the menu entry PICTURE > REAL­COLOR > COLOR TEMPERATURE. Values between 3200K and 9300K can be selected. These color temperatures are tracking the “black body curve”- the black curved line in the center of CIE Chart in Figure 7-9. The default is the D65 illuminant at 6500K.
37
Figure 7-9. CIE Chart with the black body
The white point can also be set to a custom value defined by an x, y coordinate not linked to the black body. Go to menu entry PICTURE > REALCOLOR > X-COORDINATE and PIC-
TURE > REALCOLOR > Y-COORDINATE to change the white point.
www.projectiondesign.com
7.1.5 Defining the system color gamut
All colors visible to the eye are defined by CIE Chart in Figure 7-9. The boundary of the colors the projector can display is called the system color gamut. The white triangle in Figure 7-9 is an example of a system color gamut. By default the projector has the widest possible system gamut.
The system color gamut cannot be expanded outside native color gamut.
It may be desirable to change the system color gamut of the projector to:
- Color match multiple projectors.
- Meet defined color standards, like REC 709.
- Create a special “look” to the image.
Before the system color gamut can be change the desired RealColor™ mode has to be defined. To change the RealColor™ mode, please go the menu entry PICTURE > REAL­COLOR > DESIRED VALUES > DESIRED COORDS MODE.
RealColor™ has to be enabled for the desired system gamut to be applied. Go to menu entry PICTURE > REALCOLOR > COLOR CORRECTION to enable RealColor™.
After RealColor™ is enabled and the desired color correction mode is selected, please go the menu entry PICTURE > REALCOLOR > DESIRED VALUES to change the color points to the your desired system color gamut.
For graphical visualization of the system color gamut and easy color management for a single or multiple projectors, the ProNet software package could be used. A license for the calibration software package of ProNet must be purchased separately.
38User’s Guide – Optimising the pictureF85 user’s guide – Optimising the picture
8 Maintenance
8.1 Software upgrades
In order to upgrade your projector, please follow the method described below.
• YouwillneedaUSBsticksetupwithaFAT-lesystemtoperformthisupgrade
• Accesstheupgradesoftwarefromthefollowingweb-address;
www.projectiondesign.com
• Downloadandsavethenewestrmware.zipletoyourPCdesktop
• UnzipandextractthermwareletotherootofaUSBmemorystick
• Settheprojectorinstandbymode
• InserttheUSBstickintheprojectorandwaitforafewseconds
• TheLCDdisplaywillindicatethatithasdetectedanupgradeleonthememorystick.
Wait a few seconds while the file is validated
• RemovethememorystickwhentheLCDdisplayinstructsyoutodoso.
PS! Important that the USB is safely removed from computer, using the eject function on your PC.
• Donotremovethepowercordwhiletheupgradeisstillinprogress
• Theprojectormayrestartseveraltimesduringtheupgrade
The upgrade has finished successfully when the ordinary LCD display returns.
Please refer to our website at projectiondesign.com to download the required
files or seek other information
39
www.projectiondesign.com
8.2 Lamp replacement
The LAMP indicators on the keypad will turn red when lamp life expires.
Change the lamp when lifetime expires. Always replace lamp with the same type and rating. USE ORIGINAL LAMPS ONLY.
The lamp includes an electronic lamp timer that is tracking the life time of the lamp.
Always disconnect the power cord and wait until the projector has cooled down (60 min­utes) before opening the lamp cover. Release the screw (LAMP 1) or (LAMP 2) (see below) depending on which lamp that needs to be replaced.
Be careful not to touch the protective glass when replacing the lamp, this may cause the protective glass to overheat and break while in use.
A
1 2
H
B
G
C
F
D
Be extremely careful when removing the lamp module. In the unlikely event that the bulb ruptures, small glass fragments may be generated. The lamp module is designed to contain these fragments, but use caution when removing the lamp module.
A Remove lamp lid (1 & 2) locking screws.
B Open the lamp lid(s).
C Turn the three locking screws a quarter turn anti-clockwise.
D Pull the lamp out.
E Replace with a new lamp in reverse order. When inserting a new lamp,
observe the guide pins.
F Turn the tree locking screws a quarter turn clockwise.
G Close the lamp lid.
H Turn the locking screw clockwise.
Lamp assembly 1 and 2 are different and have separate article numbers. Make sure to order the correct one when replacing one of the lamps.
In the unlikely event of a lamp rapture, a limited amount of mercury vapor may be emitted into the room. To avoid inhailing this mercury vapor (which is toxic, and can be harmful for lungs and nervous system) the room should be thoroughly ventilated for a period of at least 30 minutes. There are no known health hazards from exposure to lamps that are intact and which are used within an enclosed fixture. No adverse effects are expected from occational exposure to broken lamps. As a matter of good practise, avoid prolonged or frequent exposure to lamps unless there is adequate ventilation. The major hazard from broken lamps is the possibility of sustaining glass cuts.
E
F85 user’s guide – Maintenance
40User’s Guide – Maintenance
9 Technical specifications
9.1 Product details
technology three-chip DMD™ (Digital Micromirror Device™)
concept sealed, all-glass optical design
available resolutions WUXGA (1920 x 1200)
connectivity please refer to section 4.2.4 Connectivity for complete list
dimensions (dwh) 376 x 510 x 223 mm (ex. lens)
weight about 25 kg (ex. lens)
environmental RoHS, WEEE
security 4-digit PIN code, Kensington lock
power requirements 4.7A 230 VAC, 50 Hz
BTU/hr <2900
conformances CE, cCSAus, FCC Class A
operating temperature 0 – 40ºC / 32 – 104ºF, 0 – 1500 m
operating and storage 20 – 90% RH
lamp 2 x 400W UHP™
lamp life 1500 hrs (4000 hrs in auto switch mode*)
lamp part no. (lamp assy 1) 400-0650-xx
lamp part no. (lamp assy 2) 400-0660-xx
* Option in lamp sub menu: One lamp will be lit at the time and the projector will automatically switch between the lamps in
a specified interval (1hr to 24hr).
with lens shift
1080p (1920 x 1080) SXGA+ (1400 x 1050)
4.7A 240 VAC, 60 Hz, for US/Canada <1080W power consumption
0 – 35ºC / 32 – 95ºF, 1500 – 3000 m
For a more extensive and up to date overview of technical specifications, please refer to the product page on our home page www.projectiondesign.com
41
www.projectiondesign.com
F85 user’s guide - Technical specifications
User’s Guide - Technical specifications
42
head office
projectiondesign as
regional offices
regional contacts
Habornveien 53 N-1630 Gamle Fredrikstad, Norway ph +47 69 30 45 50 fx +47 69 30 45 80 sales@projectiondesign.com
projectiondesign locations
New York - Americas
projectiondesign LLC 295 North Street, Teterboro, NJ 07608, USA ph +1 888 588 1024 fx +1 201 288 1034 sales@projectiondesign.com
Amsterdam - EMEA
De Boelelaan 28 1083 HJ Amsterdam, The Netherlands ph +31 (0) 203301188 fx +31 (0) 204221962 sales@projectiondesign.com
Panama – Central and South America
ph +507 69 800 555 fx +47 69 30 45 80 sales@projectiondesign.com
Cape Town – Africa, Israel
ph + 27 21 79 00 018 fx +47 69 30 45 80 sales@projectiondesign.com
Beijing - China
ph + 86 0 65 63 75 07 fx + 86 10 65 63 76 46 sales@projectiondesign.com
Mumbai – SAARC Region
ph +91 98 20 61 06 70 fx +47 69 30 45 80 sales@projectiondesign.com
Dubai - UAE and Middle East
ph +9714 (4) 8872525 fx +47 69 30 45 80 sales@projectiondesign.com
Wickfield - UK & Ireland
ph +44 (0)844 8099 577 fx +47 69 30 45 80 sales@projectiondesign.com
Düsseldorf – Germany, Austria, Swtizerland
ph +49 (0) 211 22059 544 fx +49 (0) 211 22059 110 sales@projectiondesign.com
Moscow - Russia & CIS
ph +7 (495) 967 7904 fx +7 (495) 967 7600 sales@projectiondesign.com
Choszczno – Central and Eastern Europe
ph +48 883 388 035 fx +47 69 30 45 80 sales@projectiondesign.com
Sydney - Australia & New Zealand
ph +61 407976181 sales@projectiondesign.com
Singapore - South East Asia
ph +65 9621 7421 fx +47 69 30 45 80 sales@projectiondesign.com
Paris - France
ph +33 153307933 fx +47 69 30 45 80 sales@projectiondesign.com
601-0266-00
601-0267-00
All brands and trade names are the property of their respective owners. Specifications subject to change without prior notice.
©2010 projectiondesign AS. All rights reserved. All brands and trade names are the property of their respective owners. Specifications subject to All values are typical and may vary. Please visit our website for latest specifications and product updates.
change without prior notice. All values are typical and may vary. Please visit our website for latest specifications and product offerings.
Scan to learn more
www.projectiondesign.com
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use