Pro-ject Audio Tube Box SE II User Instruction

INSTRUCTIONS FOR USE
Pro-Ject Tube Box SE II
Dear music lover,
thank you for purchasing a PRO-JECT AUDIO phono amplifier. In order to achieve maximum performance and reliability you should study these instructions for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Setting the cartridge mode
The phono amplifier must be used in either MM (moving magnet) or MC (moving coil) mode according to the construction principle of the pickup cartridge to be used. Since most cartridges use the MM (moving magnet) principle the phono amplifier is factory set to operate in this mode. To find out which type your cartridge is please consult the literature accompanying your cartridge. The literature for MC cartridges should also specify the correct impedance and capacity into which the cartridge is designed to work. If in doubt please consult your dealer.
A switch at the back of the phono amplifier sets the correct level of amplification for the cartridge.
Use the supplied jumpers to set the impedance and the recommended load resistance.
The following settings are available:
17ohm s /120pF (jumper on 22, 100 and 220 Ohms)
MC -
18ohm s /120pF (jumper on 22 and 100 Ohms)
MC -
20ohm s /120pF (jumper on 22 and 220 Ohms)
MC -
22ohm s /120pF (jumper on 22 Ohms)
MC -
69ohm s /120pF (jumper on 100 and 220 Ohms)
MC -
100ohm s /120pF (jumper on 100 Ohms)
MC -
220ohm s /120pF (jumper on 220 Ohms)
MC -
MM - 47kOhms/120pF (no jumper)
47kOhms /220pF (jumper on 100pF)
MM -
47kOhms /340pF (jumper on 220pF)
MM -
47kOhms /440pF (jumper on 100pF and 220pF)
MM -
pF
220
pF
100
Ohms
Ohms
100
220
Ohms
22
Before setting MM / MC mode ore resetting jumpers the unit must be disconnected from the power supply and amplifier! Please set both channels equally.
!
-MM
-MC
Subsonic filter
A switch at the back of the phono amplifier activates and deactivates the subsonic filter.
OFF
Subsonic
ON
Connecting the record player
Connect the tonearm signal lead to the In of the phono amplifier. Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white. The earthing wire of the tonearm lead should be connected to the earth terminal.
Right
Out
220 pF
In
Power ~ 16V
Ohms 22
100 Ohms
100 pF
220 Ohms
Subsonic
OFF ON
220 pF
100 pF
100 Ohms
220 Ohms
Left
Out
Ohms 22
In
2
© Audio Trade GmbH · Pro-Ject Tube Box SE II · Revision 15.10.10/15.12.10
Connection to the amplifier
Connect the Out of the phono amplifier to a line input (such as AUX, CD, Tuner, Tape or Video) on your amplifier. Take care to connect the left and right channels correctly. The right channel is usually marked red, the left
channel black or white.
Make all connections whilst the phono amplifier is disconnected from the power supply.
!
Do not connect the phono amplifiers output to a phono input (sometimes labelled gram, disc or RIAA) on the amplifier.
Mains power connection
The phono amplifier is supplied with a power supply suitable for your country's mains supply. Check the label before connecting to ensure compliance with the mains rating in your house. Connect the low voltage plug from the power supply to the Power ~16V socket of the phono amplifier before connecting the power supply to the mains. The blue LED on the unit's front will light up once the phono amplifier is properly connected to the power supply.
Technical specifications Pro-Ject Tube Box SE II
Tubes: 2 x ECC83 (12AX 7A) Input impedance, MM: 120, 220, 340 and 440pF/47kOhm
Input impedances, MC: 17, 18, 20, 22, 69, 100 and 220ohms/120pF Output voltage: 300mV at 1kHz for 3mV (MM Input) / 0,3mV (MC input) Gain, MM / MC: 40dB / 60dB Noise floor, MM / MC: 95dB (100dB - A weighted) / 75dB (80dB - A weighted) THD MM / MC: 0,03% / 0,1% RIAA-equalisation curve accuracy: 20Hz - 20kHz / max. 0,3dB Subsonic filter: at 18Hz with 24dB/octave Input / line-level output: 1 pair RCA/Phono sockets / 1 pair RCA/Phono sockets
Outboard power supply: 16V/1.000mA AC, suitable for your country's mains supply Power consumption: 16V/850mA AC Dimensions W x H x D (D with sockets): 103 x 72 x 144 (156)mm Weight: 1.050g without power supply
Potential incorrect use and fault conditions
No signal on one or both channels: No connection between player and phono amplifier ore amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.
Strong hum: No earth connection from cartridge or arm or arm cable to phono amplifier, or earth loop.
Output too quiet or too loud, or distorted: MM / MC Mode incorrectly set - input overloading or insufficiently amplified.
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use. Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer.
PRO-JECT is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Audio Trade GmbH Copyright © 2007. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.
© Audio Trade GmbH · Pro-Ject Tube Box SE II · Revision 15.10.10/15.12.10
3
Loading...