Pro-Ject Pre Box RS digital
INSTRUCTIONS FOR USE
©
2
Dear music lover,
!
!
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
Tubes produce heat. Proper ventilation has to be guaranteed all the time. The unit must not be stacked.
!
disconnected from the power supply
which can replace original power supplies.
Analog Out
thank you for purchasing this Pro-Ject Audio Systems preamplifier.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
Safety instructions
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to disconnect the unit from the mains. Make sure that the power supply is easily
accessible at all times.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid,
such as a flower vase on or near the device. Never spill any liquid on the device or the power supply.
Never place any naked flame sources, such as lighted candles on or near the device. The product shall not
be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Never handle the device or the power supply while your hands are wet or damp.
Connectors
Make all connections whilst the preamplifier is
Take care to connect the left and right channels correctly. The right channel is usually marked red,
the left channel black or white.
Wiring XLR sockets: 1 ground, 2 “hot” and 3 “cold”.
Never use any other power supply than the one supplied with the unit except of Pro-Ject Power Boxes
Analog out
A power amplifier or active loudspeakers can be connected to the output sockets marked
(balanced connection) or RCA (unbalanced connection).
.
XLR
Pro-Ject Audio Systems · Pro-Ject Pre Box RS digital · Revision 2017.2.21
21
3
Inputs
In1 USB:
After installing the 24Bit/192kHz driver, some setting have to be done.
Project RS USB 2.0 Audio Out
make sure nothing is assigned
100
disable all enhancements
studio quality 24/192
Recommended settings for USB streaming:
SAFE
8192 or higher.
.
In 2 Sonic:
Clock out
In 3
In 9:
In 10 Analog:
Power 18-20V DC
POWER turns the unit on or back into standby
MUTE activates and deactivates mute. If mute is engaged, the blue LED
CH+/CH-
1-9
to a free USB-socket on your computer and turn it on/make sure it is powered on. The Pre Box RS digital will
be automatically detected by the computer.
24Bit/192kHz driver (Windows® operating systems only)
* For Windows
drive of you PC and follow the instructions.
For example - Windows 7® operating system:
Control Panel Hardware and Sound Sound Playback: select
Properties Supported Formats:
Enhancements:
Please note: Connection should be made to an USB-socket of your computer directly. Connecting to
USB-hubs or switches can cause problems
Pro-Ject CD Box RS. Do not connect any other devices. You can find details in instruction manual for
Pro-Ject CD Box RS.
coaxial/RCA, 4x optical/Toslink). Digital sources like CD players, TV sets, satellite/cable receivers, streamers
and also computers can be connected to these inputs.
deck, or FM tuner.
is dedicated to connect a Computer. Connect the USB-input of the unit (unit must be switched on)
®
operating systems a 24Bit/192kHz driver has to be installed. Insert the included CD into the
and ASIO buffer size
This input must be used together with
to
Pre Box RS digital offers 1 AES/EBU digital input (1x XLR) and 6 S/PDIF digital inputs (2x
This input is dedicated to source with analog output signal, e.g. phono preamplifier, tape
Advanced Default Format: set to
Level Sound: setting must be
BNC socket, which is only for connection to
Mains power connection
Connect the low voltage plug from the power supply to the
power supply to the mains.
Remote control
above the ON/OFF switch flashes.
© Pro-Ject Audio Systems · Pro-Ject Pre Box RS digital · Revision 2017.2.
select the inputs in turn
access to a specific input directly
socket before connecting the
©
4
Front panel
OUT Ohm
!
DAC 1
DAC 2
FIL 1
FIL 2
solid
tube
Headphone connection
Connect the headphones to the socket on the front panel (Jack 6,3mm) and select proper impedance with
the switch (
not be muted.)
) next to headphone socket. (When using headphones, main outputs XLR & RCA will
To switch on from standby or to standby
The switch on the left hand side of the front panel turns the unit on or back into standby. The blue LED above
the stand-by switch shows that the unit is switched on.
We recommend to set the volume control to minimum, prior to switching on.
Volume
Adjust the volume to the desired level, using the large knob on the front panel.
Input selector
After the unit is powered on, operating the switch marked with ▲ ▼ selects the inputs. The selected input will
be shown by the corresponding LED.
DAC selector
Switch to
for 24bits/192kHz and DSD capability or to
for 32bits/384kHz support.
Filter selector
Two filters are available. Switch between
and
to select desired filter.
Output stage selector
The switch on the very right side select between
tube for the first time after start of the unit requires heat up period.
state output stage and
output stage. Selecting of
Sampling frequency LED indicators
On the front panel 8 LED´s indicate current sampling frequency of the incoming digital signal. Another 2 LED´s
for DSD indicate DSD64 or DSD128.
Pro-Ject Audio Systems · Pro-Ject Pre Box RS digital · Revision 2017.2.21
21
5
DSD settings
Required settings for DSD:
0x05/0xFA
Proceed as follows:
Do not dispose the batteries as ordinary domestic refuse. Please dispose your exhausted batteries at
the appropriate collection sites - usually located at supermarkets and drugstores.
Pro-Ject Pre Box RS digital is capable of playing DSD64 and DSD128 files. For playing DSD files a dedicated
software player is required, which is also capable to play these files (for example JRiver Mediacenter,
Foobar2000 etc.).
DSD Playback Method: DoP (DSD over PCM), DoP Marker
DSD requires high data rate and slower computers may have problems with playing DSD.
.
Replacing batteries
• Unlock and slide open the battery case cover
• Replace the battery.
Make sure the battery is the right way round !
• Close the battery case cover
Battery type: 1 x CR2032 / 3V or 1 x CR2025 / 3V
Technical specifications Pro-Ject Pre Box RS digital
DACs: DAC1: 2x PCM1792 24bits/192kHz; DAC2: PCM5102
32bits/384kHz
Tubes: 2 x 6922EH
Frequency response: 20Hz - 50kHz (0dB/-0,1 dB)
Signal to noise ratio: -100dB (IEC -A)
THD: 0,005% solid state / 0,25% tube
Digital inputs: 1x USB 2.0 Audio 32/384 + DoP (DSD64/128), 1x RJ45 Sonic I2S
for CD Box RS in Sonic mode, 2x S/PDIF 24/192 coaxial, 4x
S/PDIF Optical 24/96, 1x AES/EBU balanced 24/192
Line-level inputs: 1 pair RCA/phono sockets
Input impedance: 33k
Analog outputs: Pre-out 1x XLR + 1x RCA/Cinch, Headphone (6,35mm jack)
Headphone impedance: 5/20/50
Analog input sensitivity: 1,6V rms for full headphone output
Master clock output: 16,9344MHz
Outboard power supply: 20V/3A DC, suitable for your country's mains supply
Power consumption: 300mA solid / 850mA tube / 90mA standby
Replacement battery remote control: 1 x CR2032 / 3V or 1 x CR2025 / 3V
Dimensions W x H x D (D with sockets): 206 x 72 x 200 (210)mm
Weight: 1950g without power supply
Ω
Ω switchable
© Pro-Ject Audio Systems · Pro-Ject Pre Box RS digital · Revision 2017.2.
©
6
Service
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
manufacturer from any liability over and above the lawful rights of the customer.
Pro-Ject Audio Systems is a registered Trademark of
Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for
further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible
distributor in your country.
Warranty
for use. Modification or changes to any part of the product by unauthorized persons release the
Copyright, trademarks
H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright
©
2017. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.
Pro-Ject Audio Systems · Pro-Ject Pre Box RS digital · Revision 2017.2.21
Loading...