thank you for purchasing a PRO-JECT AUDIO USB Box.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
Copyright, trademarks
PRO-JECT is a Registered Trademark of H. Lichtenegger.
Windows XP
Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
®
, Windows Vista® and Windows 7® are trademarks of the Microsoft group of companies.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the
unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use. Modification or change to any part of the product by unauthorized persons release the
manufacturer from any liability over and above the lawful rights of the customer.
Technical specifications Pro-Ject USB Box
Line-level output: 1 pair RCA/Phono sockets
Output voltage: 0,775Vrms
A/D converter: Burr Brown PCM2702E 16-Bit Delta Sigma, 8-times oversampling
Sampling rate: 44,1kHz
USB-input: digital serial data protocol USB 1.1
Operating systems: Windows XP
Dimensions W x H x D (D with sockets): 103 x 36 x 103 (109)mm
Weight: 540g
®
, Windows VISTA®, Windows 7® and Mac OS
Connection to the amplifier
Connect the Out socket to a line input (such as AUX) on your amplifier.
Make all connections whilst the USB Box is disconnected from the amplifier.
!
Take care to connect the left and right channels correctly. The right channel is usually marked red,
the left channel black or white.
Connecting to a Computer (Windows Vista® operating system)
1. Connect the USB-output of the USB Box to a free USB-socket on your computer and
turn it on/make sure it is powered on.
Please note: Connection should be made to an USB-socket of your computer directly. Connecting to
USB-hubs or switches can cause problems.
2. The “new hardware found assistant“ will detect the unit and announces it as “Burr-Brown PCM2702”.
3. Open the Playback panel. Start Control Panel Hardware and Sound Sound Playback
In the Playback panel Burr-Brown PCM2702 (announced as Speakers) should be selected (usually preselected).
4. Click the OK button and close the control panel windows.
Connecting to a Computer (Windows 7® operating system)
1. Connect the USB-output of the USB Box to a free USB-socket on your computer and
turn it on/make sure it is powered on.
Please note: Connection should be made to an USB-socket of your computer directly. Connecting to
USB-hubs or switches can cause problems.
2. Open the Playback panel. Start Control Panel Hardware and Sound Sound Playback
In the Playback panel USB Audio Device (announced as Speakers) should be selected (usually preselected).
3. Click the OK button and close the control panel windows.
Pro-Ject Direct Streaming - Kernel Streaming (Windows XP® operating system)
Normally the audio data that comes from CD gets resampled by the Windows
process deteriorates the audio performance.
®
Kernel Mixer. This conversion
CD device
44,1kHz
Kernel Mixer
resampling
to 48kHz
48kHz
Sound card
Audio output R/L
Pro-Ject Direct Streaming allows bit-by-bit processing. This avoids unwanted signal alteration of the original
®
signal through by-passing the Windows
Kernel Mixer of your PC.
For replay a suitable software player, like for instance foobar2000, will be needed.
If Pro-Ject Direct Streaming will not be used, any software player will be suitable.
CD device
44,1kHz
44,1kHz
Kernel Mixer
resampling
to 48kHz
Kernel Streaming
USB
out
48kHz
USB
cable
Sound card
Audio output R/L
Pro-Ject Direct Streaming and foobar2000 software
Downloade the software (http://box-designs.com/main.php?prod=usbbox&cat=digital&lang=en)
and install it. To do so, double-click install.bat and follow the instructions.
Complete the installation by restarting the computer.
Please be aware that downloads from the Internet are made entirely at your own risk. Under no
circumstances can we carry responsibility or provide support for software products sourced from the
internet or for any damage or problems arising from the use thereof. All downloads should be
checked with an up-to-date anti-virus programme. License fees may be applicable.