Pro-Ject Set iPod goes digital User Manual

INSTRUCTIONS FOR USE

Pro-Ject “iPod goes digital”-Set

Dear music lover,

thank you for purchasing a Pro-Ject “iPod goes digital”-Set. In order to achieve maximum performance and reliability you should study these instructions for use carefully.

Warning of a hazard for the user, the units or possible misuse.

Important notice.

Safety instructions

AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the voltage in your area meets the voltage requirements printed on the power supply.

The power cord/power supply is used to disconnect the unit from the mains. Make sure that the power cord/power supply is easily accessible at all times. cord/power supply while your hands are wet or damp.

Avoid letting liquids enter the device or the power supply. Never place any item containing liquid, such as a flower vase on or near the device. Never spill any liquid on the device or the power supply. Never place any naked flame sources, such as lighted candles on or near the device. The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.

Never handle the device, the power

What’s in the box

Stereo Box S including remote control handset, power supply and power cord Dock Box S Digital including remote control handset and power supply 2 x Speaker Box 5 including wall mount brackets and instruction for use Design Box 2iP Acryl Speaker cable, length 2 x 2 meter

8 x banana plugs (4mm ) Interconnect cable, length 25cm

Connectors - Stereo Box S

Record Out

Left

Pro-Ject Audio Systems, Vienna, Austria

Right

Make all connections whilst the amplifier is disconnected from the power supply.

Left

Right

Connecting amplifier and docking station

Connect, using the supplied interconnect cable, the sockets IN1 on the amplifier to the sockets OUT on the Dock Box S Digital.

Inputs Line level sources such as CD player radio or TV can be connected to the input sockets marked IN1 or IN2.

The volume level of the Dock Box has to be set to max..

Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white.

Connecting amplifier and speakers

The output terminals accept loudspeaker cables terminated with 4mm  Banana plugs, spades connectors or naked wire. Connect the cable terminals on the amplifier to the terminals on the speakers.

The red speaker terminals carry the positive signal (+), the black speaker terminals the negative signal (–). Make sure the polarity of the connection is correct at each end of the cables.

Only connect one loudspeaker with an impedance not less than 4 ohms per channel.

Record output, connecting a headphone amplifier - Stereo Box S

Record Out connects an analogue record device ore a Pro-Ject Head Box headphone amplifier.

Record Out provides a fixed output level.

Connectors - Dock Box S Digital

Pro-Ject Audio Systems, Vienna, Austria

Make all connections whilst the Dock Box is disconnected from the power supply.

Connection to an integrate, pre, power amplifier or active speakers

Connect the Left/Right Out socket to a high level input on your integrated or pre amplifier, the pre input on your power amplifier or active speakers.

Connected to devices with a volume control, the volume level of the Dock Box has to be set to max..

Turn the Dock Box volume level to minimum before switching on your power amplifier or active speakers.

Connection to a external D/A-converter

Connect the S/PDIF Co-axial out socket to a coaxial digital input on the D/A converter or AV processor. Doing so allows you to use the signal in its digital for further digital processing.

Connection to a TV-set or a beamer

Connect the S-VIDEO socket to a s-video input of your TV-set or beamer.

„All digital“ units, such as iPhone 5®, do not support the s-video output.

Fitting and adjustment of the iPod®/iPhone® cradle

Use the knurled screw supplied to fix the cradle to the Dock Box chassis. Do not fully tighten the screw yet. Now place your iPod

iPod

/iPhone® and tighten the screw.

This device is suitable for iPods®/iPhones® with 30-pole connector only. To connect units with a lightning-connector, such as iPhone

(lightning connector Use without the cradle will eventually break the 30-pole connector of the Dock Box and the socket of

the iPod

/iPhone® on the Dock Box contacts. Move the cradle so that it supports the

5 or iPod® Touch 5, a lightning-adapter



30-pole connector) is needed.

/iPhone® Before connecting the iPod®/iPhone® any sort of cover has to be removed.

+ 4 hidden pages