Pro-Ject Debut Carbon EVO Setup Guide with Sumiko Rainier
Debut Carbon EVO
Setup Guide
Getting started:
• Make sure to have enough space to unpack your turntable.
• Always unpack and setup in a clean enviroment.
• Please Do NOT throw away the packaging! If you need a
service or want to return your product, please send them in
the original packaging including all inserts. In case of any
damage in another packaging your dealer cannot guarantee a full refund.
Unpack all items from accessory bag.
1 32
a) Anti Skating Weight
b) Adapter for 7“ singles
c) Connect it E RCA cable
d) Round belt for 78 RPM
e) Standard at belt for 33/45 RPM
a) b) c)
d)
e)
• complete manual:
www.project-audio.com/en/product/debut-carbon-evo
Remove dust cover carton from the box.
Lift the wrapped turntable out of the box.
Carefully remove the protection covering.
4
Tonearm is fragile!
Put the drive belt on the pulley
8 10 11
and sub-platter.
Unpack the counterweight.
5
Put the platter on the turntable.
9
Unpack the power supply.
6
Use the rocker switch to select the
playback speed.
7
Unpack the platter.
The turntable should always be placed on
a at surface. Check with a spirit level.
12
Large pulley for round belt (78 RPM)
If necessary, level the turntable by
adjusting the feet.
13
Remove tonearm twist tie.
14
LEFT: 33 RPM RIGHT: 45 RPM / 78 RPM
STOPS THE MOTOR
Put the counterweight in place.
15
0°
Remove the needle protection cover.
16
20
Put a record on the platter.
Turn the whole counterweight counterclockwise until the scale reads 18 - 20.
17
21
Place the tonearm between platter
and armrest.
Lower the tonearm with the lift.
Put the loop of the Anti Skating Weight in
the second groove on the tonearm post.
Balance the tonearm so it stays level by
18
22
turning the counterweight forwards and
backwards on the rod.
Balance the tonearm so it stays level by
turning the counterweight forwards and
backwards on the rod.
0°
Unpack Dust Cover and put it on the
turntable.
19
23
Turn the front dial of the counterweight
(not the whole weight) so the ‘0’ is in line
with marker at the back of the tonearm.
Connect to your hi-system and enjoy
your music!
>
Debut Carbon EVO
Connect to any amp with integrated phono amplier or
use an external phono preamp like our Tube Box S2.
Need help?
Feel free to contact us. We have experienced partners
all over the world. Find your dealer here:
www.project-audio.com/en/nd-a-dealer/
Possible Setup:
Pro-Ject Speaker Box 5 S2 (bookshelf speaker)
and Pro-Ject MaiA S2 (stereo integrated amplier).
Speaker cable
Connect it E (RCA Cable)
Speaker cable
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further
advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country.
Warranty repairs will only be aected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the
diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt.
Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the
original packaging. Modication or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and
above the lawful rights of the customer.
Warranty: Terms and Conditions
• A warranty is valid only for products purchased from an authorized Pro-Ject Audio Systems retailer or dealer.
• This warranty oer is limited to the repair of the equipment (which could be a repair or replacement at our discretion, neither of which aects
your original warranty).
• Neither transportation or any other costs, nor any risk for removal, transportation and installation of products is covered by this warranty.
• A warranty is only valid for the original owner. It is not transferable.
• To validate your warranty, you will need to provide the original sales invoice or other proof of ownership and date of purchase.
• Warranty must be claimed within two years of purchase from an authorized dealer. After this period of time, the warranty will expire.
• The legal warranty obligation exists in addition to this warranty and is not limited by this warranty.
A Pro-Ject Audio Systems warranty relates to claims of defects in materials and/or workmanship at the time of purchase. It does not cover:
• Deterioration of component parts, the nature of which is to become worn or depleted with use, such as batteries and headphone ear pads,
drive belts and cartridges.
• Damages caused by incorrect installation, connection or packing.
• Damages caused by any use other than the correct use described in the user manual, negligence, modications, or use of parts that are not
made or authorized by Pro-Ject Audio Systems.
• Damages caused by faulty or unsuitable ancillary equipment.
• Damages caused by accidents, lightning, water, re heat, war, public disturbances or any other cause beyond the reasonable control of
Pro-Ject Audio Systems and its appointed distributors.
• Products where the serial number has been altered, deleted, removed or made illegible.
• Repairs or modications that have been executed by an unauthorized person.
Commercial Use
Faults caused due to using domestic products in commercial environments or on commercial scales are not covered by warranty. This turntable is
intended for domestic use only. Using them for business applications are done so at your own risk.
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright © 2020. All rights reserved.
The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specication without prior notice as deemed necessary to uphold the ongoing process of technical development.
Loading...