PROformance Hoops Pro Series, Pro 672, Pro 560, Pro 660, Pro 554 Installation & Owner's Instructions

...

Download

Page 1

Pro Series

IInntteerrnnaall JJaacckk AAddjjuussttaabbllee

HHeeiigghhtt GGooaa ll SSyysstteemm

•

Pro67

•

Pro66

•

Pro56

•

Pro55

•

Pro45

•

Pro44

IInnssttaallllaattiioonn

2 0 0 4 4 8

&& OOwwnneerr’’ss IInnssttrruuccttiioonnss

MMaaddee IInn TThhee UUSSAA

Page 2

Pro Series Int. Jack System Instructions

This manual explains the proper installation, operation and maintenance of your Proformance Hoops Goal. Study and understand these instructions thoroughly before installing or operating the goal. Failure to do so could result in serious injury or death and/or equipment damage. Consult Proformance Hoops if you do not understand the instructions in this manual or need additional information.

Proformance Hoops recommends that you retain this manual for future reference of operation, maintenance and parts information.

The instructions, illustrations and specifications in this manual are based on the latest information available at the time of publication. Your goal may have product improvements and options not yet contained in this manual.

Proformance Hoops reserves the right to make changes at any time without notice or obligation.

Additional copies of these instructions are available from Proformance Hoops.

22 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

This product is covered by various U.S. and Canadian patents,

including U.S. Patent #5,211,393.

Patent infringement will be prosecuted.

No part of this manual may be reproduced in any form or by any

means electronic or mechanical, including photocopying, recording,

or by any information storage and retrieval systems without the

express written consent of Proformance Hoops.

Revised 9/8/2009

Proformance Hoop

QQuueessttiioonnss?? CCoommmmeennttss?? CCoonnttaacctt UUss::

PPhhoonnee:: 888888..335533..44666677

wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm

Page 3

Pro Series Int. Jack System Instructions

TABLE OF CONTENTS

Contact Informatio

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Thank Yo

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Lay Out Playing Cour

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Court Markings (reference only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Safety Instruction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Ground Anchor Installatio

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Call "One-Call" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Required Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Ground Anchor Placement

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7

Installatio

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8

Dig Hole

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Position Anchor and Fill With Concrete . . . . . . . . . . . . . . . . . . . . . .7-8

Goal Specification

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13

Goal Assembl

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Required Tools and Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Hardware Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-11

Parts List – Pro 672 & Pro 660 . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15

Parts List – Pr

o 560 & Pro 554 . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17

Parts List – Pro 454 & Pro 448 . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19

Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21

Backboard Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Goal Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Rim Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Height Indicator Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Permanent Crank Handle Attachment . . . . . . . . . . . . . . . . . . . . . . . .25

Operation and Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Warrantie

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 33

Page 4

Pro Series Int. Jack System Instructions

44 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

TThhaannkk yyoouu aanndd ccoonnggrraattuullaattiioonnss ffoorr ppuurrcchhaassiinngg aa PPrrooffoorrmmaannccee HHooooppss GGooaall –– tthhee ffiinneesstt bbaasskkeettbbaallll ggooaall ssyysstteemm oonn tthhee mmaarrkkeett ttooddaayy!!

You will discover that Proformance Hoops is unsurpassed in product innovation, quality and integrity in the basketball equipment industry. We are continually focused on designing, engineering and producing products that meet and exceed the expectations of today’s toughest playing environments and demanding players.

THANK YOU!

LAY OUT PLAYING COUR

Consider the following to determine where to install the basketball goal:

•

Whether the goal is to be installed into a landscaped area next to the playing surface or into a hard-surfaced area.

•

Backboard size and its extension distance from the structure.

•

If court markings are to be used.

•

Amount of playing surface desir

ed beneath the goal.

•

Other functions of playing surface (such as driveway

, tennis court, etc.)

Court

Markings (reference only)

6'-0"

19'-9"

50'-0" Optimum Inside Sidelines

15'-0"

19'-0"

25'-0"

63"

15"

12'-0"

4'-0"

NNoottee::

Lines are 2" wide.

Regulation Court Lengths:

High School: 84' College: 94' Professional: 94'

Page 5

Pro Series Int. Jack System Instructions

Failure to follow these safety instructions may result in serious injury or death and/or propert

damage.

•

Do not install or use this product unless the instructions within this manual have been carefully read and understood.

•

Consult Proformance Hoops if you do not understand the instructions in this manual or need additional information.

•

Before digging for the ground anchor, contact your local One-Call system in your area.

•

If using a ladder during assembly, use extreme caution. Two or three people are recommended for safe installation and assembly.

•

Installation and assembly of this product will require lifting and bending that may result in injury to anyone not accustom to this type of activity.

•

Ensure there are no overhead power lines within a 20 ft. (7 m.) radius of the goal location.

•

Climate, corrosion or misuse could result in system failure.

•

With rim set at 6'-0" playing height, the minimum operational height is 5'-4" (1.9 m) to the bottom of the backboard.

•

DO NOT HANG on the rim or any part of the goal system. This includes the backboard, support braces or net.

•

During play, especially when performing dunking activities, keep the player’s face away from the backboard, rim and net. Serious injury could result if teeth/face come in contact with the backboard, rim or net. Do not wear jewelry or other loose objects that could become entangled in the net.

•

Twice yearly, check the goal system for loose hardware, excessive wear and signs of corrosion. Repair the system befor

e use.

•

Never play on damaged equipment.

SAFETY INSTRUCTION

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 55

Page 6

Pro Series Int. Jack System Instructions

66 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

GROUND ANCHOR INSTALLATIO

Contacting buried utilities may cause serious injury or death. Before you start digging, always contact your local One-Call system to help prevent personal injury, interruption of services, environmental accidents or job delays.

Electric lines can shock or electrocute. Gas lines can rupture causing explosion or fire. Laser light in fiber optic cable can cause blindness.

One-Call will notify participating utility companies of your proposed digging project.

If you do not know the number for the local One-Cal

l in your area, call the National One-Call at 1-888-258-0808 for this information

After being notified, utility companies will mark their

underground facilities by using the following international marking codes:

Color

Definitio

Red Electric

Yellow Gas, Oil or Petroleum

Orange Communication, Telephone, TV

Blue Portable Water

Green/Brown Sewer

White Proposed Excavation

Pink Surveying

• Spade

• Shovel

• Tape Measure

• Level

• Stir Rod

• Water

Required Tools and Materials

• Auger or Post Hole Digger 10-14, 60 lb. Bags of Dry Concrete Mix

(or 1/4 - 1/3 yard of ready mix concrete may be substituted for the concrete mix)

IIMMPPOORRTTAANNTT ––

When preparing for ground anchor, allow at least 6" (152 mm) from all sides of ground anchor to wall of hole to allow for sufficient concrete fill around anchor.

Use the following guidelines when installing ground anchor into a

landscaped are

next to the playing surface:

••

Top of ground anchor to be flush with or slightly above playing surface.

••

Top of ground anchor must be level both directions across its surface.

••

Concrete fill should have top sloped away from anchor in all directions to shed moisture away.

••

Hinge side of anchor toward playing surface.

••

Hinge parallel with playing surface.

••

Distance from edge of playing surface to anchor to be no less than 6" (152 mm).

••

Distance from bottom of ground anchor plate to concrete fill to be no less than 1" (25 mm).

48-50"

(1.2-1.3 m)

1" (25 mm) minimum

18" (0.5 m)

6" (152 mm) all sides

Playing Surface

GROUND ANCHOR PLACEMENT

Page 7

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 77

Use the following guidelines when installing ground anchor into a

hard-surfaced area

•

Top of ground anchor to be 1" (25 mm) above playing surface.

•

Concrete fill should have top sloped away from anchor in all directions to shed moisture away.

•

Top of ground anchor must be level both directions across its surface.

•

Hinge side of anchor toward playing surface.

•

Hinge parallel with playing surface.

•

Distance from edge of hole made in playing surface to anchor to be no less than 6" (152 mm).

•

Distance from bottom of ground anchor plate to concrete fill to be no less than 1" (25 mm).

GROUND ANCHOR PLACEMENT (continued

)

48-50"

(1.2-1.3 m)

1" (25 mm)

8" (0.5 m)

6" (152 mm) a

ll sides

Playing Surface

GROUND ANCHOR INSTALLATIO

Dig Hole

– When installing goal into a

har

d-surfaced area, a minimum of a 18" x 18" (0.5 x 0.5 m) area of the hard surface will need to be removed.

Step 1

– Once location of goal has been

determined, locate center of ground anchor hole.

Step 2

– Dig a hole approximately 18 " (0.5 m) in diameter and 48-50" (1.2-1.3 m) deep. Use a spade, shovel, auger or post hole digger.

Position Anchor and Fill Hole with Concrete Mi

– For best

performance,

do not

fully fill hole with concrete mix before positioning

the anchor

Instead

fill base of hole with concr

ete mix, lower the ground anchor into the hole, position it and then finish filling with concrete mix.

48-50"

(1.2-1.3 m)

18" (0.5m)

Diameter

Page 8

GROUND ANCHOR INSTALLATION (continued)

Pro Series Int. Jack System Instructions

Step 1

– Locate and unpack ground anchor.

Do not remove plastic plugs or hinge bolt.

Step 2

– Place 2-3 bags of concrete mix into

hole; add water and stir

. Follow concrete mix

manufacturer’s instructions for best results.

Step 3

– Position anchor in center of hole with hinge side toward and parallel with playing surface.

IMPORTANT

– As hole is filled with concrete mix, periodically place a level on top of anchor plate and check that it is level front-to-back and left-to-right. Also check that the top of anchor is at correct height.

Step 4

– Adjust anchor plate height, depending upon installation, per

guidelines given in Ground Anchor Placement.

Step 5

– Continue filling hole with concrete mix until it is within 1"-1.5" (25-38 mm) of anchor plate bottom, or level with landscape – whichever comes first.

IMPORTANT

– Top of concrete fill should be sloped away fr

om anchor

in all directions to shed moisture away.

6" (152 mm) m

inimum AND

parallel

Check level both directions

Playing Surface

88 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

GOAL ASSEMBL

IMPORTANT

Concrete must cure a minimum of

48 hours

before installing

goal.

IMPORTANT

Safe assembly of the goal requires two to three people in

good physical condition and capable of lifting 80-100 lbs (36-45 kg) each.

IMPORTANT

Locate and familiarize yourself with all parts of the goal

before beginning assembly.

Level Rubber Mallet 12' Tape Measure Phillips Scr

ewdriver

Ratchet

9/16" and 3/4" Sockets 15/16" Socket (4" & 5" poles only) 15/16" Wrench (4" & 5" poles only) 9/16" and 3/4" W

enches

Required Tools and Materials

Page 9

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 99

HARDWARE IDENTIFICATIO

RRiimm BBoolltt AAsssseemmbbllyy

(All Models)

Description

Model

Parts List

Lengt

Callout

Extension Arm Bolt

Pro 560/Pro 554 #8 8-1/2"

Extension Arm Bolt Pro 454/Pro 448 #8 7-1/2"

Jack-To-Extension Pro 560/Pro 554 #10 2-1/4" Arm Bolt

Jack-To-Extension Pro 454/Pro 448 #10 8" Arm Bolt

Backboard Bolt Pro 560/Pro 554 #12 2-1/2"

Backboard Bolt Pro 454/Pro 448 #12 8"

Backboard Bolt Pro 672/Pro 660 #12 3-1/4"

GGrroouunndd AAnncchhoorr BBoolltt

(All Models)

44aa

44bb

AAnncchhoorr HHiinnggee BBoolltt

(All Models)

22aa

22bb

AAsssseemmbbllyy LLoocckk PPllaattee

(All Models)

11//44"" xx 11//44"" SShhoouullddeerr

BBoolltt JJaacckk SShhaafftt

EExxtteennssiioonn

(models with 4" & 5" poles)

1199

1155aa

1155bb

1155cc

JJaacckk HHaannddllee

(All Models)

77bb

77aa

Refer to pages 14-19 for descriptions, model usage and quantities

1155dd

Page 10

Pro Series Int. Jack System Instructions

1100 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

HARDWARE IDENTIFICATIO

EExxtteennssiioonn AArrmm TToo PPoollee PPiivvoott PPiinn AAsssseemmbbllyy –– 1100--77//88""

(Pro 672 & Pro 660)

88bb

88aa

88bb

JJaacckk--TToo--EExxtteennssiioonn AArrmm PPiivvoott PPiinn AAsssseemmbbllyy

(Pro 672 & Pro 660)

1100cc

1100bb

1100aa

1100bb

1100cc

1100dd

RRiimm BBoolltt BBaacckkppllaattee

(Pro 454 & Pro 448)

Page 11

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 1111

HARDWARE IDENTIFICATIO

HHeeiigghhtt IInnddiiccaattoorr DDeeccaall

(All Models)

1166

GGrroommmmeett

(All Models)

1177

UUpp--DDoowwnn DDeeccaall

(All Models)

1188

55//3322"" HHeexx KKeeyy

(Provided – Pro 672 & Pro 660)

11//88"" HHeexx KKeeyy

(Provided – 4" & 5" Pro 560, Pro 554, Pro 454 & Pro 448)

55//6644"" HHeexx KKeeyy

(Provided – All Models)

BBllaacckk TToouucchh--UUpp PPaaiinntt

Page 12

Pro Series Int. Jack System Instructions

GOAL SPECIFICATION

1122 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

MMooddeell PPoollee BBaacckkbbooaarrdd WWeeiigghhtt WWeeiigghhtt HHeeiigghhtt

SSiizzee SSiizzee WWiitthh AAccrryylliicc WWiitthh GGllaassss RRaannggee ((AA))

PPrroo 667722

6" x 6" 42" x 72" 463 lbs. 524 lbs. 6'-10'

PPrroo 666600

6" x 6" 38" x 60" 460 lbs. 511 lbs. 6'-10'

PPrroo 556600

5" x 5" 38" x 60" 339 lbs. 390 lbs. 6'-10'

PPrroo 555544

5" x 5" 36" x 54" 327 lbs. 366 lbs. 6'-10'

PPrroo 445544

4" x 4" 36" x 54" 268 lbs. 309 lbs. 6'-10'

PPrroo 444488

4" x 4" 32" x 48" 263 lbs. 298 lbs. 6'-10'

MMooddeell EExxtteennssiioonn DDiissttaannccee ((BB)) aatt:: RRiimm ttoo TToopp--ooff--GGooaall

DDiissttaannccee ((CC))

PPrroo 667722

33-3/4"

PPrroo 666600

29-3/4"

PPrroo 556600

29-3/4"

PPrroo 555544

27-3/4"

PPrroo 445544

27-3/4"

PPrroo 444488

23-3/4"

1100'' 88'' 66''

51" 54" 48"

38" 42" 37"

32" 36" 28"

MMooddeell CCrraannkk CCrraannkk OOffffsseett PPoollee OOffffsseett

DDiissttaannccee ((DD)) HHeeiigghhtt ((EE)) HHeeiigghhtt ((FF)) HHeeiigghhtt ((GG)) DDiissttaannccee ((HH))

PPrroo 667722

11-1/2" 36-1/2" 7'-0" 10'-5" 21"

PPrroo 666600

11-1/2" 36-1/2" 7'-0" 10'-5" 21"

PPrroo 556600

10-1/2" 36-1/2" 6'-6" 9'-8" 16"

PPrroo 555544

10-1/2" 36-1/2" 6'-6" 9'-8" 16"

PPrroo 445544

10-1/2" 36-1/2" 6'-6" 9'-8" 13-1/2"

PPrroo 444488

10-1/2" 36-1/2" 6'-6" 9'-8" 13-1/2"

Page 13

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 1133

Playing Surface

Page 14

Pro Series Int. Jack System Instructions

1144 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

1133

PARTS LIST – Pro 672 &Pro 660

NNOOTTEE::

Refer to page 15

for parts descriptions.

NNOOTTEE::

Refer to page

9-11 for hardware descriptions.

BBaacckkbbooaarrdd AAsssseemmbbllyy

AAsssseemmbbllyy LLoocckk PPllaattee –– 66""

PPoollee

GGrroouunndd AAnncchhoorr

JJaacckk AAsssseemmbbllyy

HHaarrddwwaarree

AAnncchhoorr HHiinnggee BBoolltt

1144

1155

RRiimm && NNeett AAsssseemmbbllyy aanndd HHaarrddwwaarree

1122

HHaarrddwwaarree

(4 places)

1111

UUppppeerr EExxtteennssiioonn AArrmm

1166

HHeeiigghhtt DDeeccaall && GGrroommmmeett

1177

HHaarrddwwaarree

1188

UUpp--DDoowwnn DDeeccaall

(backside)

JJaacckk HHaannddllee

LLoowweerr EExxtteennssiioonn AArrmm

1100

HHaarrddwwaarree

Page 15

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 1155

PARTS DESCRIPTIO

RREEFF PPrroo 667722 PPrroo 666600 DDEESSCCRRIIPPTTIIOONN

1 1 Ground Anchor – 6"

22aa

1 1 Anchor Hinge Bolt, 3/8"-16 UNC x 7"

22bb

1 1 Nut, 3/8"-16 UNC

1 1 Pole – 6" x 6"

44aa

5 5 Bolt, 1/2"-13 UNC x 1-1/4"

44bb

5 5 Lock Washer, 1/2"

1 1 Assembly Lock Plate – 6"

1 1 Jack Assembly

77aa

1 1 Jack Handle

77bb

2 2 8-32 Setscrew

88aa

2 2 3/4" dia. x 10-7/8" Pivot Pin

88bb

4 4 3/4" I.D. Set Collar

1 1 Lower Extension Arm

1100aa

1 1 1" dia. x 2-1/4" Pivot Pin

1100bb

2 2 Nylon Washer, 1"

1100cc

2 2 Fender Washer, 1-1/2" OD x 5/16"

1100dd

2 2 Socket Screw, 1/4"-20 x 1/2" SS BH

1111

1 1 Upper Extension Arm

1122aa

4 4 Bolt, 1/2"-13 UNC x 3-1/4"

1122bb

8 8 1/2" Flat Washer

1122cc

4 4 1/2" Locknut

1133

1 – Backboard Assembly, 42" x 72"

– 1 Backboard Assembly, 38" x 60"

1144

1 1 Rim and Net Assembly

1155aa

4 4 Bolt, 3/8"-16 UNC x 2"

1155bb

8 8 Flat Washer, 3/8"

1155cc

4 4 Lock Washer, 3/8"

1155dd

4 4 Flange Nut, 3/8"-16 UNC

1166

1 1 Decal, Height Indicator

1177

1 1 Grommet

1188

1 1 Decal, Up–Down

Page 16

Pro Series Int. Jack System Instructions

1166 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

PARTS LIST – Pro 560 & Pro 554

1133

NNOOTTEE::

Refer to page 17

for parts descriptions.

NNOOTTEE::

Refer to page

9-11 for hardware descriptions.

BBaacckkbbooaarrdd AAsssseemmbbllyy

AAsssseemmbbllyy LLoocckk PPllaattee –– 55""

PPoollee

GGrroouunndd AAnncchhoorr

JJaacckk AAsssseemmbbllyy

HHaarrddwwaarree

AAnncchhoorr HHiinnggee BBoolltt

1144

1155

RRiimm && NNeett AAsssseemmbbllyy aanndd HHaarrddwwaarree

1122

HHaarrddwwaarree

(4 places)

1111

UUppppeerr EExxtteennssiioonn AArrmm

1166

HHeeiigghhtt DDeeccaall && GGrroommmmeett

1177

HHaarrddwwaarree

1188

UUpp--DDoowwnn DDeeccaall

(backside)

JJaacckk HHaannddllee

LLoowweerr EExxtteennssiioonn AArrmm

1100

HHaarrddwwaarree

1199

JJaacckk SShhaafftt EExxtteennssiioonn

Page 17

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 1177

PARTS DESCRIPTIO

RREEFF PPrroo 556600 PPrroo 555544 DDEESSCCRRIIPPTTIIOONN

1 1 Ground Anchor – 5"

22aa

1 1 Anchor Hinge Bolt, 3/8"-16 UNC x 6"

22bb

1 1 Nut, 3/8"-16 UNC

1 1 Pole – 5" x 5"

44aa

5 5 Bolt, 1/2"-13 UNC x 1-1/4"

44bb

5 5 Lock Washer, 1/2"

1 1 Assembly Lock Plate – 5"

1 1 Jack Assembly

77aa

1 1 Jack Handle

77bb

2 2 8-32 Setscrew

88aa

2 2 Bolt, 5/8"-11 UNC x 8-1/2"

88bb

4 4 Flat Washer, 5/8"

88cc

2 2 Locknut, 5/8"-11 UNC

1 1 Lower Extension Arm

1100aa

1 1 Bolt, 5/8"-11 UNC x 2-1/4"

1100bb

1 1 Locknut, 5/8"-11 UNC

1111

1 1 Upper Extension Arm

1122aa

4 4 Bolt, 1/2"-13 UNC x 2-1/2"

1122bb

8 8 Flat Washer, 1/2"

1122cc

4 4 Locknut, 1/2"-13 UNC

1133

1 – Backboard Assembly, 38" x 60"

– 1 Backboard Assembly, 36" x 54"

1144

1 1 Rim and Net Assembly

1155aa

4 4 Bolt, 3/8"-16 UNC x 2"

1155bb

8 8 Flat Washer, 3/8"

1155cc

4 4 Lock Washer, 3/8"

1155dd

4 4 Nut, 3/8"-16 UNC

1166

1 1 Decal, Height Indicator

1177

1 1 Grommet

1188

1 1 Decal, Up–Down

1199

1 1 1/4" x 1/4" Shoulder Bolt Jack

Shaft Extension

Page 18

Pro Series Int. Jack System Instructions

1188 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

PARTS LIST – Pro 454 & Pro 448

1133

NNOOTTEE::

Refer to page 19

for parts descriptions.

NNOOTTEE::

Refer to page

9-11 for hardware descriptions.

BBaacckkbbooaarrdd AAsssseemmbbllyy

AAsssseemmbbllyy LLoocckk PPllaattee –– 44""

PPoollee

GGrroouunndd AAnncchhoorr

JJaacckk AAsssseemmbbllyy

HHaarrddwwaarree

AAnncchhoorr HHiinnggee BBoolltt

1144

1155

RRiimm && NNeett AAsssseemmbbllyy aanndd HHaarrddwwaarree

1122

HHaarrddwwaarree

(2 places)

1111

UUppppeerr EExxtteennssiioonn AArrmm

1166

HHeeiigghhtt DDeeccaall && GGrroommmmeett

1177

HHaarrddwwaarree

1188

UUpp--DDoowwnn DDeeccaall

(backside)

JJaacckk HHaannddllee

LLoowweerr EExxtteennssiioonn AArrmm

1100

HHaarrddwwaarree

1199

JJaacckk SShhaafftt EExxtteennssiioonn

Page 19

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 1199

PARTS DESCRIPTIO

RREEFF PPrroo 445544 PPrroo 444488 DDEESSCCRRIIPPTTIIOONN

1 1 Ground Anchor – 4"

22aa

1 1 Anchor Hinge Bolt, 3/8"-16 UNC x 5"

22bb

1 1 Nut, 3/8"-16 UNC

1 1 Pole – 4" x 4"

44aa

5 5 Bolt, 1/2"-13 UNC x 1-1/4"

44bb

5 5 Lock Washer, 1/2"

1 1 Assembly Lock Plate – 4"

1 1 Jack Assembly

77aa

1 1 Jack Handle

77bb

2 2 8-32 Setscrew

88aa

2 2 Bolt, 5/8"-11 UNC x 7-1/2"

88bb

4 4 Flat Washer, 5/8"

88cc

2 2 Locknut, 5/8"-11 UNC

1 1 Lower Extension Arm

1100aa

1 1 Bolt, 5/8"-11 UNC x 8"

1100bb

2 2 Flat Washer, 5/8"

1100cc

1 1 Locknut, 5/8"-11 UNC

1111

1 1 Upper Extension Arm

1122aa

2 2 Bolt, 1/2"-13 UNC x 8"

1122bb

4 4 Flat Washer, 5/8"

1122cc

2 2 Locknut, 1/2"-13 UNC

1133

1 – Backboard Assembly, 36" x 54"

– 1 Backboard Assembly, 32" x 48"

1144

1 1 Rim and Net Assembly

1155aa

4 4 Bolt, 3/8"-16 UNC x 2"

1155bb

8 8 Flat Washer, 3/8"

1155cc

4 4 Lock Washer, 3/8"

1155dd

4 4 Nut, 3/8"-16 UNC

1166

1 1 Decal, Height Indicator

1177

1 1 Grommet

1188

1 1 Decal, Up–Down

1199

1 1 1/4" x 1/4" Shoulder Bolt Jack

Shaft Extension

Page 20

Pro Series Int. Jack System Instructions

2200

wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

POLE ASSEMBL

Step 1

Remove five plastic plugs

om threaded holes in ground

anchor. Also remove hinge bolt

and nut (these will be used in Step 3.)

NOTE:

Use protective padding to

protect pole finish.

Step 2

Unpack pole and jack.

NOT

: On the all models, the jack assembly is already installed in the pole.

Step 3

Align pole hinge

with

anchor plate hinge

and insert

bolt

(#2 in parts list) and nut.

Step 4

Lift pole to approximately

30º and attach lock plate

ground anchor and pole.

IMPORTANT

: The 30º pole

installation angle MUST

be maintained until pole is raised in Goal Alignment.

Step 5:

Pull jack assembly

out slightly, remove packing and protective materials from end of jack and reposition jack in pole.

Step 6:

Insert crank handle through access hole and slide onto shaft.

NOTE:

If a permanent crank handle installation is desired, refer to Permanent Crank Handle Attachment.

Page 21

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprr

ooffoorrmmaanncceehhooooppss..ccoomm 2211

POLE ASSEMBLY (continued)

Step 7: Pro 672, Pro 660, Pro 560 & Pr

554 Only

Position lower extension arm

with clevis

toward pole offset. Align lower extension

arm pivot holes with lower holes

pole.

Step 7: Pro 454 &Pro 448 Only

Position lower extension arm with gusset

away from pole offset. Align lower

extension arm pivot holes with lower holes

in pole.

Step 8

Attach lower extension arm to pole

using the following:

PPrroo 667722 && PPrroo 666600::

3/4" x 10-7/8" pin and two lock collars (#8 in parts list). Tighten with 5/32" hex key (provided).

PPrroo 556600 && PPrroo 555544::

5/8" x 8-1/2" bolt (#8 in parts list), two flat washers and locknut.

PPrroo 445544 && PPrroo 444488::

5/8" x 7-1/2" bolt (#8 in parts list), two flat washers and locknut.

NOTE:

On the Pro 560, Pro 554, Pro 454 & Pro 448 models, tighten so that bushings on extension arms meet bushings in pole.

Step 9

Attach upper extension arm

pivot holes with upper holes

in pole.

Attach arm to pole using the following:

PPrroo 667722 && PPrroo 666600::

3/4" x 10-7/8" pin and two lock collars (#8 in parts list). Tighten with 5/32" hex key (provided).

PPrroo 556600 && PPrroo 555544::

5/8" x 8-1/2" bolt (#8 in parts list), two flat washers and locknut.

PPrroo 445544 && PPrroo 444488::

5/8" x 7-1/2" bolt (#8 in parts list), two flat washers and locknut.

NOTE:

On the Pro 560, Pro 554, Pro 454 & Pro 448 models, tighten so that bushings on extension arms meet bushings in pole.

Step 10:

Attach upper mount of jack to

lower extension arm using the following:

PPrroo 667722 && PPrroo 666600::

1" x 2-1/4" pin, two nylon washers, two fender washers, and two 1/2" socket screws (#10 in parts list). Tighten with 5/32" hex key (provided).

PPrroo 556600 && PPrroo 555544::

5/8" x 2-1/4" bolt (#10 in parts list) and locknut.

PPrroo 445544 && PPrroo 444488::

5/8" x 8" bolt (#10 in parts list), two flat washers and locknut.

NOTE:

On the Pro 560, Pro 554, Pro 454 & Pro 448 models, do NOT over tighten. Snug tighten only.

ontender & Champion Only

Page 22

Pro Series Int. Jack System Instructions

2222 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

BACKBOARD ATTACHMENT

IIMMPPOORRTTAANNTT::

Pole MUST be at original 30º installation angle as specified in Pole Assembly.

SStteepp 11::

Open lid of box containing

backboard

and position the backboard (without removing it from box) face down under lower extension arm

with rim mounting

plate

toward pole.

NNOOTTEE::

Backboards are attached to

extension arms using the following:

PPrroo 667722 && PPrroo 666600::

Four 1/2" x 31/4" bolts, eight flat washers and four locknuts (#12 in parts list).

HHaarrddwwaarree SSeeqquueennccee::

Bolt passes through flat

washer - arm bracket - backboard bracket -

arm bracket - flat washer - locknut.

PPrroo 556600 && PPrroo 555544::

Four 1/2" x 21/2" bolts (#12 in parts list), eight flat washers and four locknuts.

HHaarrddwwaarree SSeeqquueennccee::

Bolt passes through flat

washer - arm - backboard bracket - flat washer

- locknut.

PPrroo 445544 && PPrroo 444488::

Two 1/2" x 8" bolts (#12 in parts list), four 5/8" flat washers and two 1/2" locknuts.

NNOOTTEE::

5/8" washer needs to be seated properly over nylon bushing on outside of backboard H-frame.

HHaarrddwwaarree SSeeqquueennccee::

Bolt passes through flat

washer - backboard bracket - extension arm –

extension arm – backboard bracket - flat

washer - locknut.

SStteepp 22::

Align lower backboard holes

with

lloowweerr

extension arm holes

. Attach backboard to arm using hardware noted above.

SStteepp 33::

Align upper backboard holes

with

uuppppeerr

extension arm holes 66. Attach backboard to arm using hardware noted above.

NNOOTTEE:: PPrroo 667722 && PPrroo 666600::

Do not over

tighten. Snug tighten only.

PPrroo 556600 && PPrroo 555544::

Do not over tighten. Tighten so that bushings in arms meet bushings in backboar

Page 23

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 2233

GOAL ALIGNMENT

IMPORTANT

For safe assembly, do the following:

•Use two or three people to raise the goal assembly and hold it in a vertical position. They should be in good physical condition and capable of lifting 80-100 lbs (35-45 kg).

•DO NOT adjust height of backboard or attach rim until pole is raised and bolted down.

•Correct sequence of hardware installation MUST be followed during assembly.

Step 1:

Locate five 1/2" x 1-1/4" bolts

(#4 in parts list). Prepare them for use by having lock washer

slipped on as

shown.

Step 2:

Push up on backboard to raise goal assembly to vertical position. The assembly lock plate, maintaining pole at 30º installation angle, will fall away. Save lock plate for future disassembly.

Step 3:

Fasten pole

to threaded

ground anchor plate

as follows:

•First, install and tighten three back bolts

with lock washers.

•Second, remove ground anchor hinge bolt and nut

7 . Save for

future disassembly

•Third, install and tighten two front bolts

with lock washers.

Step 4:

Check goal assembly with a level and inspect visually to

determine if it is parallel and plumb to playing surface.

Step 5:

If adjustments are necessary, slightly loosen bolts to rotate

goal or place shims between pole plate and ground anchor plate.

Step 6:

Fully tighten five bolts.

IMPORTANT

The bolts must pass all the way through the ground

anchor plate. If they ar

e r

ecessed within the plate when fully

tightened, please contact Proformance Hoops.

oth Sides

Page 24

Pro Series Int. Jack System Instructions

2244 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

RIM ATTACHMENT

NNOOTTEE::

Use all steps of the following instructions to install a reflex rim. To install a static rim, follow all steps except #2 and #6.

SStteepp 11::

Remove any cardboard edge protectors

and protective sheeting from backboard.

NNOOTTEE::

Four steel shouldered bushings

are factory installed. If loose, make sure to have them seated properly when tightening rim bolts. If missing, contact Proformance Hoops or dealer to get replacements.

DO NOT install rim withou

bushings.

SStteepp 22::

If not already removed, remove cover plate

screws

and cover plate

from rim assembly.

IIMMPPOORRTTAANNTT::

Correct sequence of hardware

installation MUST be followed during assembly.

SStteepp 33::

Loosely attach rim

to backboard

through top mounting holes

with two 3/8" x 2" bolts (#14 in parts list), four flat washers, two lock washers and two nuts. Snug tighten hardware – a 9/16" open-end wrench may be necessary.

IIMMPPOORRTTAANNTT ((PPrroo 445544 && PPrroo 444488))::

When attaching rim to TOP mounting holes, attach rim bolt backplate

at same time.

Hardware Sequence:

Bolt passes through flat washer - rim backplate - backboard bushing - backboard mounting plate - flat washer - lock washer - nut.

SStteepp 44::

Repeat procedure outlined in Step 3 for

lower rim mounting holes

SStteepp 55::

Level rim side to side and then fully

tighten hardware.

SStteepp 66::

Position cover plate

and attach with

cover plate screws

SStteepp 77::

Attach net to rim.

Page 25

Pro Series Int. Jack System Instructions

11..888888..335533..44666677 wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 2255

HEIGHT INDICATOR ATTACHMENT

PERMANENT CRANK HANDLE ATTACHMEN

Step 1:

Position top of rim 6' above playing surface using crank handle. Measure distance with a tape measure for accuracy.

Step 2:

Insert height decal

with

printed number ‘6’ thr

ough indicator hole in pole and attach to internal height indicator plate.

Step 3:

Repeat steps for 61⁄2', 7', 71⁄2', 8',

⁄2', 9', 91⁄2', and 10' rim heights. Use height decals with printed numbers ‘6

⁄2’, ‘7’, ‘71⁄2’, ‘8’, ‘81⁄2’, ‘9’, ‘91⁄2’, and

‘10’.

Step 4:

Install plastic grommet

into

indicator hole.

Step 5:

Attach UP/DOWN decal

pole above crank handle hole.

NOTE:

Step 1 is only performed on

goals with 4" and 5" poles.

Step 1:

Insert shoulder bolt jack shaft

extension

into tapped hole on jack shaft. Tighten with 1/8" hex key (provided).

Step 2:

Attach handle

to shaft using

set scr

ews

and 5/64" hex key

(provided).

Page 26

Pro Series Int. Jack System Instructions

2266

wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 11..888888..335533..44666677

OPERATION

Pinlock

(option) Remove handle and push lock onto jack handle shaft. Use key to remove.

NOTE:

To use Pinlock on goals with 4" and 5" poles, a shaft extension must be installed – refer to instructions with Permanent Crank Handle Attachment.

Height Indicator indicates goal

height from 6' to 10'.

The exterior finish of your Proformance Hoops goal is designed for outdoor environments and should only require periodic cleaning and inspection for imperfections that could develop over time (see Maintenance section).

When cleaning is necessary, Proformance Hoops recommends using water and a mild dish detergent applied with a soft, non-abrasive cloth.

IIMMPPOORRTTAANNTT::

DO NOT use abrasive cleaners to clean the goal. Damage to

the finish may result.

CLEANIN

Crank – Turn clockwise for goal to go up, turn counter clockwise for goal to go down.

Page 27

Pro Series Int. Jack System Instructions

11..888888..335533..44666677

wwwwww..pprrooffoorrmmaanncceehhooooppss..ccoomm 2277

Proformance Hoops uses a two-part acrylic-enamel paint on our goals. With periodic inspection and service when needed, the high-gloss finish is designed to last for many years. A small bottle of black paint with brush is provided with every goal for touch up of imperfections as they develop and can be found in the hardware kit.

If more touch up is required, please contact Proformance Hoops.

MAINTENANCE

LUBRICATION

Jack Assembly

PPrroo 667722 && PPrroo 666600 aarree eeqquuiippppeedd wwiitthh aa ggrreeaassee zzeerrkk

– use several shots of grease.

AAllll ootthheerr

ggooaallss aarree eeqquuiippppeedd wwiitthh aa lluubbrriiccaattiioonn ppoorrtt

. Use several shots of grease or a liberal amount of general-purpose lubricating oil.

IIMMPPOORRTTAANNTT

– A general-purpose lubricating oil like “3-in-1” or lightweight motor oil is recommended. DO NOT use penetrating oil like “WD-40”. Proformance Hoops has “Maintenance Kits” available which would include a bottle of lubricating oil. Contact Proformance Hoops for details.

Use a liberal amount of general-purpose

lubricating oil. DO NOT use a penetrating oil.

Every jack that comes with a Proformance Hoops height-adjustable goal is pre-lubricated as it comes from the factory. With any mechanical component, periodic inspection and service is required. Proformance Hoops recommends applying lubrication at least once or twice a year to keep a smooth operation of the height actuator. There are two lubrication service points provided. Failure to do so could result in jack failure and not be covered under warranty.

Page 28

WARRANTIES

BUYER AGREES THAT ALL PRODUCTS SOLD BY PROFORMANCE HOOPS CARRY THE FOLLOWING WARRANTY

Subject to proper installation, and normal intended use, all structural components of ProView Series*, Pro Series*, Force Series*, and Wall Mount Basketball Systems are warranted to the original owner to be free of defects in materials and workmanship for the duration of ownership by the original retail purchaser, subject to the limitations below. The Traditional Basketball Systems will be covered by this warranty for a period of five years. Portable Series* Systems will be covered by this warranty for a period of two years. Proformance Hoops shall have the right to require the purchaser to deliver the allegedly defective products to Proformance Hoops for testing, repair, or replacement. Proformance Hoops shall not be responsible for any expense associated with the replacement or removal of the product from its application for such delivery. Freight and Handling charges may apply to covered warranty parts. Modification of any product by the customer, unless approved by Proformance Hoops, will void all warranty. Where listed as “LIMITED”, the warranties shall cover damage of failure that occurs during the course of NORMAL or INTENDED USE of the product. Normal or intended use shall be described as activity that is necessary for the participation in the sport for which the equipment is damaged. NOT COVERED is damaged caused by deliberate hanging, multiple player hanging, vandalism, non-basketball activities, or any other activity that could be regarded as abusive.

Padding Warranty: Multi-Purpose Backboard Edge Padding: one year limited; Indoor Backboard Edge Padding: five year limited (indoor only); Custom-Fit Pole Padding: one year limited; Wrap-Around Pole Padding: one year limited.

NOT COVERED BY THIS WARRANTY

 Use in non-residential applications of Glass backboards.  Use in non-residential applications of Tradition complete systems.  Any products subjected to abuse, negligence, improper installation, vandalism, acts of God, alteration of product or any other events

beyond the control of Proformance Hoops.

 Paint or rusted parts.  Deterioration of product due to time and wear.

Normal deterioration of products due to atmospheric conditions, weather, rust, wear and tear (including paint), or other causes that do not affect functional use are not covered by Proformance Hoops warranties. All warranties are valid only when product is used in the intended application, and when installed according to Proformance Hoops instructions. Warranty will be void if maintenance instructions in the Owner’s Manual are not followed, including jack lubrication on a bi-yearly basis. If you did not receive an Owner’s Manual, please contact ProformanceHoops.com and one will be sent to you.

WARRANTY CLAIMS: All returns must be arranged through the local dealer if available. Warranties do not cover dealer service charges,

labor charges, freight or travel expense associated with replacement, repair, or removal of warranty item. A warranty claim form must be completed, and photos submitted for any item you wish to claim under warranty. If the purchase was not made through a dealer, this form is available by email. In response to your claim, you will receive an order confirmation as well as a notice stating whether Proformance Hoops needs your warranty item returned. Proformance Hoops will notify you if we determine that the item cannot be claimed under warranty. Proformance Hoops is not responsible for any charges for labor to install or repair defective product prior authorization. Proformance Hoops will determine the most economical method to either repair or replace product before any work is to commence.

TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IF PROFORMANCE HOOPS CANNOT DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN TO THE EXTENT POSSIBLE ANY CLAIMS UNDER SUCH IMPLIED WARRANTIES SHALL EXPIRE OR EXPIRATION OR THE APPLICABLE WARRANTY PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. PROFORMANCE HOOPS DOES NOT ASSUME OR AUTHORIZE ANY PERSON TO ASSUME FOR US, ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF OUR PRODUCTS.

TO THE MAXIMUM EXTENT PERMITTED BY LAW, PROFORMANCE HOOPS ASSUMES NO RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHICH MAY ARISE FROM THE PURCHASERS OR USE OF OUR EQUIPMENT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

IF ANY PROVISION OF THIS WARRANTY IS INVALID, VOID OR UNENFORCEABLE IN ANY INSTANCE OR RESPECT, THE UNENFORCEABLE PROVISION WILL BE SEVERED AND REFORMED TO EFFECT THE INTENT OF THIS LIMITED WARRANTY TO THE MAXIMUM EXTENT POSSIBLE, AND THE REMAINING PROVISIONS SHALL CONTINUE IN FULL FORCE AND EFFECT AND SHALL BE ENFORCED TO THE FULL EXTENT PERMITTED BY LAW.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state

B0312

www.proformancehoops.com 1.888.353.4667