CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Serial Number
Decal
Model No. PFCCEX01210.0
Serial No.
Write the serial number in the
space above for reference.
USERʼS MANUAL
www.proform.com
QUESTIONS?
If you have questions, or if parts
are damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-936-4266
Mon.–Fri., 7:30 until 16:30 ET
(excluding holidays)
OR E-MAIL US:
customerservice@iconcanada.ca
All manuals and user guides at all-guides.com
all-guides.com
2
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
I
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE EXERCISE BIKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.
PROFORM XP is a trademark of ICON IP, Inc.
All manuals and user guides at all-guides.com
3
WARNING: T
o reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise bike before using your exercise bike.
ICON assumes no responsibility for personal injury or property damage sustained by or through the
use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or per-
sons with pre-existing health problems.
2. Use the exercise bike only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise bike are ade-
quately informed of all precautions.
4. The exercise bike is intended for home use
only. Do not use the exercise bike in a com-
mercial, rental, or institutional setting.
5. Keep the exercise bike indoors, away from
moisture and dust. Place the exercise bike
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is at least 2 ft. (0.6 m) of clearance
around your exercise bike.
6. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
7. Keep children under age 12 and pets away
from the exercise bike at all times.
8. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the exercise bike. Always wear
athletic shoes for foot protection.
9. The exercise bike should not be used by
persons weighing more than 250 lbs.
(113 kg).
10. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. The exercise bike does not have a free
wheel; the pedals will continue to move until
the flywheel stops. Reduce your pedaling
speed in a controlled way.
12. Always keep your back straight while using
the exercise bike; do not arch your back.
13. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
IMPORTANT PRECAUTIONS
All manuals and user guides at all-guides.com
4
BEFORE YOU BEGIN
Seat
Seat Post Knob
Pedal/Strap
Transport Wheel
Console
Seat Knob
Handgrip Pulse Sensor
Water Bottle Holder*
*Water bottle is not included
Thank you for selecting the revolutionary PROFORM
®
XP 185 U exercise bike. Cycling is an effective exer-
cise for increasing cardiovascular fitness, building
endurance, and toning the body. The XP 185 U exer-
cise bike provides an impressive selection of features
designed to make your workouts at home more effec-
tive and enjoyable.
For your benefit, read this manual carefully before
you use the exercise bike. If you have questions
after reading this manual, please see the back cover
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
number decal are shown on the front cover of this
manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
All manuals and user guides at all-guides.com
5
M10 x 54mm Button Screw (33)–2
M10 x 78mm Button Screw (67)–2
M8 Locknut
(37)–4
M8 Split
Washer (36)–8
M10 Split
Washer (34)–4
M6 Locknut
(54)–4
M6 Split
Washer (43)–4
M8 x 20mm Button
Screw (35)–4
M8 x 25mm Patch
Screw (50)–2
M4 x 16mm
Screw (40)–9
M6 x 8mm Button
Screw (56)–1
M6 x 38mm Button
Bolt (53)–4
ASSEMBLY
Assembly requires two persons. Place all parts of the exercise bike in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires an adjustable wrench and a Phillips
screwdriver .
Use the part drawings below to identify the small parts used in assembly. The number in parentheses below
each drawing refers to the key number of the part, from the PART LIST near the end of this manual. The number
following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit,
check to see if it has been preassembled.
All manuals and user guides at all-guides.com
6
2. Slide the Right Cap (77), which is marked with
a “Right” sticker, onto the right side of the Rear
Stabilizer (14).
Attach the Right Cap (77) with two M4 x 16mm
Screws (40).
Attach the Left Cap (4) in the same way.
3
2
1.
Orient the Rear Stabilizer (14) so that the indi-
cated holes are facing downward.
W
hile another person lifts the rear of the Frame
(1), attach the Rear Stabilizer (14) to the Frame
with two M10 x 54mm Button Screws (33) and
two M10 Split Washers (34).
3. While another person lifts the front of the Frame
(1), attach the Front Stabilizer (2) to the Frame
with two M10 x 78mm Button Screws (67) and
two M10 Split Washers (34).
1
1
2
14
34
33
Holes
77
4
40
34
67
14
1
Holes
To make assembly easier, read the
i
nformation on page 5 before you begin.
All manuals and user guides at all-guides.com
all-guides.com
7
5. Identify the Right Handlebar (48), which is
marked with an “R” sticker.
While a second person holds the Right
Handlebar (48) near the Upright (3), tie the pull
wire to the right pulse wire (A), and then pull it
upward out of the top of the Upright. Then, untie
and discard the pull wire.
Slide the Right Handlebar (48) onto the Upright
(3).
Attach the Right Handlebar (48) with two M6 x
38mm Button Bolts (53), two M6 Split Washers
(43), and two M6 Locknuts (54). Make sure that
the hexagonal holes are in the indicated
location.
Attach the Left Handlebar (47) in the same
way.
Orient the Water Bottle Holder (49) as shown.
Insert the Upper Wire Harness (32) and the right
and left pulse wires (A, B) through the Water
Bottle Holder.
Slide the Water Bottle Holder (49) onto the
Upright (3) and attach it with an M4 x 16mm
Screw (40). Do not tighten the Screw yet.
5
4
4. While another person holds the Upright (3) near
the Frame (1), connect the Upper Wire Harness
(32) to the Lower Wire Harness (31).
Tip: Avoid pinching the wire harnesses.
G
ently pull the upper end of the Upper Wire
Harness (32) to remove the slack, and slide the
Upright (3) onto the Frame (1).
Attach the Upright (3) with four M8 x 20mm
Button Screws (35) and four M8 Split Washers
(36).
35
35
36
32
31
36
48
54
43
53
32
49
47
B
A
Hexagonal
Holes
40
3
3
1
A
void pinching the
wire harnesses
Right
Pulse
Wire
Pull
Wire
Pull Wire
All manuals and user guides at all-guides.com
8
7. While another person holds the Console (6)
near the Upright (3), connect wires on the
Console to the Upper Wire Harness (32) and to
the pulse wires (A, B).
Tip: Avoid pinching the wires. Insert the
excess wires downward into the Upright (3).
Attach the Console (6) to the Console Bracket
(55) with four M4 x 16mm Screws (40).
See step 5. Tighten the M4 x 16mm Screw (40).
7
6. Orient the Console Bracket (55) as shown.
Insert the Upper Wire Harness (32) and the right
a
nd left pulse wires (A, B) through the Console
Bracket (55).
Tip: Avoid pinching the wires. Attach the
Console Bracket to the Upright (3) with two M8
x 25mm Patch Screws (50).
6
5
5
55
40
50
6
32
32
A, B
A, B
3
3
Avoid pinching
the wires
Avoid pinching
the wires
8. The Console (6) requires four 1.5V D batteries
(not included); alkaline batteries are recom-
mended. IMPORTANT: If the exercise bike
has been exposed to cold temperatures,
allow it to warm to room temperature before
inserting batteries into the Console. If you
do not do this, the console displays or other
electronic components may become dam-
aged. Press the tabs on the battery cover and
remove the battery cover. Insert four batteries
into the battery compartments; make sure that
the batteries are oriented as shown by the
diagrams inside the battery compartments.
Then, reattach the battery cover.
6
Batteries
Batteries
Battery
Cover
8
All manuals and user guides at all-guides.com
9
9. Orient the Seat Post (5) as shown.
Loosen the Seat Post Knob (30) a few turns.
Pull the Seat Post Knob outward, insert the Seat
P
ost (5) into the Frame (1), and then release the
Seat Post Knob into one of the holes in the Seat
Post.
Move the Seat Post (5) upward and down-
ward slightly to make sure that the pin on the
Seat Post Knob (30) is engaged in one of the
adjustment holes in the Seat Post. Then,
tighten the Seat Post Knob.
9
5
1
30
10
10. Orient the Seat (12) and the Seat Carriage (29)
as shown.
Attach the Seat (12) to the Seat Carriage (29)
with four M8 Locknuts (37) and four M8 Split
Washers (36).
Loosen the Seat Knob (11) and slide the Seat
Carriage (29) onto the Seat Post (5) until it
stops.
Next, attach an M6 x 8mm Button Screw (56) to
the Seat Post (5).
Then, adjust the Seat Carriage (29) to the
desired position and tighten the Seat Knob (11).
56
12
29
36
11
37
36
5
All manuals and user guides at all-guides.com
10
12. Make sure that all parts are properly tightened before you use the exercise bike. Note: After assembly is
completed, some extra parts may be left over. Place a mat beneath the exercise bike to protect the floor.
11. Identify the Right Pedal (26), which is marked
with an “R.”
U
sing an adjustable wrench, firmly tighten the
Right Pedal (26) clockwise into the right arm of
t
he Crank (13).
Tighten the Left Pedal (not shown) counter-
clockwise into the left arm of the Crank.
IMPORTANT: Tighten both Pedals as firmly
as possible. After using the exercise bike for
one week, retighten the Pedals. For best per-
formance, keep the Pedals tightened.
Adjust the strap on the Right Pedal (26) to the
desired position, and press the end of the strap
onto the tab on the side of the Right Pedal.
Adjust the strap on the Left Pedal (not
shown) in the same way.
11
26
Tab
Strap
13
All manuals and user guides at all-guides.com
11
HOW TO USE THE EXERCISE BIKE
HOW TO ADJUST THE HEIGHT OF THE SEAT
For effective exercise, the seat should be at the proper
height. As you pedal, there should be a slight bend in
y
our knees when the pedals are in the lowest position.
To adjust the height
of the seat, first
loosen the seat post
knob. Next, pull the
knob, slide the seat
post upward or
downward to the
desired position,
and then release
the knob. Move the
seat post upward
or downward
slightly to make
sure that the knob
is engaged in one of the adjustment holes in the
seat post. Then, tighten the knob.
HOW TO ADJUST THE HORIZONTAL POSITION OF
THE SEAT
To adjust the hori-
zontal position of
the seat, first loosen
the seat knob a few
turns. Then, move
the seat forward or
backward to the
desired position,
and firmly tighten
the seat knob.
HOW TO ADJUST THE PEDAL STRAPS
To adjust the pedal
straps, first pull the
e
nds of the pedal
straps off the tabs
on the pedals.
Adjust the pedal
straps to the desired
position, and then
press the ends of
the pedal straps
onto the tabs.
Seat Knob
Seat
Seat
Post
Seat
Pedal Strap
Tab
Seat
Post
Knob
All manuals and user guides at all-guides.com
all-guides.com
12
FEATURES OF THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode, you can change the
resistance of the pedals with the touch of a button. As
you exercise, the console will provide continuous exer-
cise feedback. You can even measure your heart rate
using the handgrip pulse sensor.
The console also offers ten preset workouts that auto-
matically change the resistance of the pedals and
prompt you to increase or decrease your pedaling
pace while guiding you through an effective workout.
The console also features the new iFit interactive
workout system. The iFit interactive workout system
enables the console to accept iFit cards containing
workouts designed to help you achieve specific fitness
goals.
For example, lose unwanted pounds with the 8-week
Weight Loss workout. iFit workouts control the resis-
tance of the pedals while guiding you through your
workouts. iFit cards are available separately. To pur-
chase iFit cards, go to www.iFit.com or call the
telephone number on the front cover of this man-
ual. iFit cards are also available at select stores.
To use the manual mode, see page 13. To use a
preset workout, see page 14. To use an iFit work-
out, see page 15.
Note: If there is a sheet of plastic on the face of the
console, remove the plastic.
CONSOLE DIAGRAM
All manuals and user guides at all-guides.com
13
HOW TO USE THE MANUAL MODE
1. Turn on the console.
To turn on the console, press any button or begin
p
edaling. The display will light and the console will
be ready for use.
2. Select the manual mode.
Each time you turn on
the console, the man-
ual mode will be
selected. If you have
selected a workout,
reselect the manual
mode by pressing the Workout button repeatedly
until zeros appear in the display.
3. Begin pedaling and change the resistance of
the pedals as desired.
As you pedal, change
the resistance of the
pedals by turning the
Resistance dial. To
increase the resis-
tance, turn the
Resistance dial clockwise; to decrease the resis-
tance, turn the Resistance dial counterclockwise.
Note: After you change the resistance, it will take a
moment for the pedals to reach the selected resis-
tance level.
4. Follow your progress with the display.
The upper section of
the display will show
the elapsed time and
the distance, in miles
or kilometers, that you
have pedaled. The dis-
play will change modes every few seconds.
Note: When you select a preset workout the dis-
play will show the time remaining in the workout
instead of the elapsed time.
The second section
of the display will
show your pedaling
p
ace in miles or kilo-
meters per hour.
The third section of
the display will show
the approximate num-
ber of calories you
have burned and the
resistance level of the
pedals. The display will change modes every few
seconds.
The display will also show your heart rate when
you use the handgrip pulse sensor (see step 5 on
page 14).
The last section of
the display will show
a track representing
1/4 mile (400 meters).
As you exercise, indi-
cators will appear in
succession around the track until the entire track
appears. The track will then disappear and the
indicators will again begin to appear in succession.
Note: The console
can show speed and
distance in either
miles or kilometers.
The letters MPH or
Km/H will appear in
the display to indicate which unit of measurement
is selected. To change the unit of measurement,
press and hold down the Workout button for a few
seconds. An “E” for English miles or an “M” for
metric kilometers will appear in the display. Press
the Start button repeatedly to select the desired
unit of measurement. Then, press the Workout
button. Note: When you replace the batteries, it
may be necessary to reselect the unit of measure-
ment.
All manuals and user guides at all-guides.com
14
To view the total distance pedaled since the exer-
cise bike was purchased and the total number of
hours the exercise bike has been used, press and
h
old down the Workout button for a few seconds.
T
he total distance pedaled will appear in the first
section of the display. The total number of hours
the exercise bike has been used will appear in the
third section of the display. To return to the manual
mode, press the Workout button.
5. Measure your heart rate if desired.
If there are sheets
of plastic on the
metal contacts on
the handgrip pulse
sensor, remove the
plastic. Next, hold
the handgrip pulse
sensor with your
palms resting on the
metal contacts.
Avoid moving your
hands or gripping
the contacts too
tightly.
When your pulse is detected, a heart-shaped sym-
bol will flash in the display each time your heart
beats and then your heart rate will be shown. For
the most accurate heart rate reading, hold the con-
tacts for at least 15 seconds.
6. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for a few seconds, the
time will begin to flash in the display and the con-
sole will pause.
If the pedals do not move for a few minutes and
no buttons are pressed, the console will turn off
and the display will be reset.
HOW TO USE A PRESET WORKOUT
1. Turn on the console.
To turn on the console, press any button or begin
p
edaling. The display will light and the console will
be ready for use.
2. Select a preset workout.
To select a preset workout, press the Workout but-
ton repeatedly until the number of the desired
workout appears in the display.
The first section of the
display will show how
long the workout will
last. A profile of the
resistance levels for
the workout will scroll
across the last section of the display. Note:
Complete profiles of the preset workouts are
printed on the sides of the console.
3. Start the workout.
Press the Start button or begin pedaling to start
the workout.
Each workout is divided into 30 one-minute seg-
ments. One resistance level and one pace setting
are programmed for each segment. Note: The
same resistance level and/or pace setting may be
programmed for consecutive segments.
During the workout, the workout profile will show
your progress. The flashing segment of the profile
represents the current segment of the workout.
The height of the flashing segment indicates the
resistance level for the current segment. At the
end of each segment of the workout, a series of
tones will sound and the next segment of the pro-
file will begin to flash. If a different resistance level
is programmed for the next segment, the resis-
tance level will flash in the center display for a few
seconds to alert you. The resistance of the pedals
will then change.
Contacts
All manuals and user guides at all-guides.com
15
As you exercise, the
display will prompt you
to keep your pedaling
p
ace near the pace
setting for the current
s
egment. When the
word “faster” appears in the display, increase your
pace. When the word “slower” appears, decrease
your pace. When the center of the target flashes,
maintain your current pace.
IMPORTANT: The pace settings are intended
only to provide motivation. Your actual pace
may be slower than the pace settings. Make
sure to pedal at a pace that is comfortable for
you.
If the resistance level for the current segment is
too high or too low, you can manually override the
level by turning the Resistance dial. IMPORTANT:
When the current segment of the workout
ends, the pedals will automatically adjust to
the resistance setting for the next segment.
If you stop pedaling for several seconds, the time
will begin to flash in the display. To restart the
workout, press the Start button or simply resume
pedaling.
The workout will continue until the display shows a
time of 0:00. If you continue to pedal after the
workout is completed, the display will continue to
show exercise feedback; however, the display will
not show the elapsed time until you select the
manual mode or a new workout.
4. Follow your progress with the display.
See step 4 on page 13.
5. Measure your heart rate if desired.
See step 5 on page 14.
6. When you are finished exercising, the console
will turn off automatically.
See step 6 on page 14.
HOW TO USE AN IFIT WORKOUT
1. Turn on the console.
To turn on the console, press any button or begin
p
edaling. The display will light and the console will
be ready for use.
2. Insert an iFit card and select a workout.
To use an iFit workout, insert an iFit card into the
iFit slot; make sure that the iFit card is oriented so
the metal contacts are face-down and are facing
the slot. When the iFit card is properly inserted,
the indicator next to the slot will light and words
will appear in the display.
Next, select the desired workout on the iFit card
by pressing the up and down buttons next to the
iFit slot.
Press the Start button or begin pedaling to start
your workout. iFit workouts function in the same
way as preset workouts. To use the workout, see
steps 3 to 6 on pages 14 and 15.
3. When you are finished exercising, remove the
iFit card.
Remove the iFit card when you are finished exer-
cising. Store the iFit card in a secure place.
iFit Slot
iFit Card
All manuals and user guides at all-guides.com
16
Inspect and properly tighten all parts of the exercise
b
ike regularly. Replace any worn parts immediately. To
clean the exercise bike, use a damp cloth and a small
amount of mild soap—never use alcohol, abrasives,
or chemicals to clean the exercise bike.
IMPORTANT: To avoid damage to the console,
keep liquids away from the console and keep the
console out of direct sunlight.
CONSOLE TROUBLESHOOTING
If the console display becomes dim, replace all the
batteries at the same time; most console problems are
the result of low batteries. To replace the batteries,
see assembly step 8 on page 8.
If the console does not display your heart rate when
you use the handgrip pulse sensor, see step 5 on
page 14.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, first remove the left pedal by turning it clock-
wise with an adjustable wrench.
Next, remove the screws from the left and right
shields; there are three sizes of screws in the
shields—note which size of screw you remove
from each hole. Then, remove the left shield.
Locate the Reed Switch (21). Turn the Crank (13) until
a Magnet (16) is aligned with the Reed Switch.
Loosen, but do not remove, the indicated M4 x 16mm
Flange Screw (61).
Slide the Reed Switch (21) slightly closer to or away
f
rom the Magnet (16) , and then retighten the M4 x
16mm Flange Screw (61). Turn the Crank (13) for a
moment.
R
epeat these actions until the console displays correct
feedback. When the reed switch is correctly adjusted,
reattach the left shield and the left pedal.
HOW TO ADJUST THE DRIVE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance is at the highest level, the
drive belt may need to be adjusted.
To adjust the drive belt, you must first remove the right
pedal and the right shield. Using an adjustable
wrench, turn the right pedal counterclockwise and
remove it.
Next, remove the screws from the left and right
shields; there are three sizes of screws in the
shields—note which size of screw you remove
from each hole. Then, remove the right shield.
Loosen the M10 x 22mm Bolt (45). Tighten the M8 x
38mm Hex Screw (69) until the drive belt is tight.
Then, retighten the M10 x 22mm Bolt (45). Reattach
the right shield and the right pedal.
MAINTENANCE AND TROUBLESHOOTING
16
21
61
13
45
69
All manuals and user guides at all-guides.com
all-guides.com
17
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
b
ody uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
EXERCISE GUIDELINES
WARNING: Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
h
ealth problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
All manuals and user guides at all-guides.com
18
11Frame
21Front Stabilizer
31Upright
4
1 Left Cap
51Seat Post
61Console
71Flywheel
81Resistance Motor
94M4 x 12mm Screw
10 1 Resistance Arm
11 1 Seat Knob
12 1 Seat
13 1 Pulley/Crank
14 1 Rear Stabilizer
15 2 Transport Wheel
16 2 Magnet
17 1 Left Shield
18 1 Right Shield
19 1 Resistance Motor Bracket
20 1 Seat Post Bushing
21 1 Reed Switch/Wire
22 2 Clamp
23 1 Drive Belt
24 1 Left Pedal/Strap
25 2 Flywheel Bearing
26 1 Right Pedal/Strap
27 1 Crank Bearing Set
28 1 Idler
29 1 Seat Carriage
30 1 Seat Post Knob
31 1 Lower Wire Harness
32 1 Upper Wire Harness
33 2 M10 x 54mm Button Screw
34 4 M10 Split Washer
35 4 M8 x 20mm Button Screw
36 8 M8 Split Washer
37 6 M8 Locknut
38 2 M8 x 25mm Shoulder Patch Screw
39 2 M4 x 64mm Screw
40 17 M4 x 16mm Screw
41 1 M4 x 30mm Screw
42 1 Flywheel Axle
43 4 M6 Split Washer
4
4 1 Long C-Magnet Spacer
45 1 M10 x 22mm Bolt
46 1 C-magnet
47 1 Left Handlebar w/Pulse Wire
48 1 Right Handlebar w/Pulse Wire
49 1 Water Bottle Holder
50 2 M8 x 25mm Patch Screw
51 2 Handlebar Cap
52 1 M10 Locknut
53 4 M6 x 38mm Button Bolt
54 4 M6 Locknut
55 1 Console Bracket
56 2 M6 x 8mm Button Screw
57 1 Short C-magnet Spacer
58 4 V-clip
59 1 M10 x 80mm Shoulder Bolt
60 1 Resistance Wheel
61 7 M4 x 16mm Flange Screw
62 1 M3.5 x 12mm Screw
63 2 Foot
64 1 M4 x 5mm Screw
65 4 M3.8 x 20mm Round Head Screw
66 3 M10 Washer
67 2 M10 x 78mm Button Screw
68 1 M4 x 16mm Bright Screw
69 1 M8 x 38mm Hex Screw
70 4 M4 Locknut
71 3 M8 x 20mm Flat Head Screw
72 2 Foam Grip
73 1 Seat Plate
74 2 Upper Contact
75 2 Lower Contact
76 1 Wire Clamp
77 1 Right Cap
*–Userʼs Manual
*–Assembly Tool
PART LIST—Model No. PFCCEX01210.0 R0510A
Key No. Qty. Description Key No. Qty. Description
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
All manuals and user guides at all-guides.com
19
2
1
5
3
4
77
6
10
30
13
14
16
20
21
22
23
24
26
31
32
33
36
37
40
61
39
28
38
42
44
45
46
52
29
35
35
36
15
40
47
50
51
37
48
53
53
54
7
8
12
17
18
27
19
15
25
25
11
67
34
34
34
34
36
36
36
36
36
37
38
39
40
40
40
40
49
50
54
55
56
57
58
59
60
61
62
40
40
63
63
64
72
65
65
40
74
75
74
75
43
43
43
43
41
73
71
66
66
61
22
68
66
9
70
40
40
69
61
76
37
51
EXPLODED DRAWING—Model No. PFCCEX01210.0 R0510A
All manuals and user guides at all-guides.com
Part No. 298573 R0510A Printed in China © 2010 ICON IP, Inc.
LIMITED WARRANTY
ICON of Canada, Inc. (ICON) warrants this product to be free from defects in workmanship and material,
under normal use and service conditions. Parts and labor are warranted for ninety (90) days from the date
of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All
repairs for which warranty claims are made must be preauthorized by ICON. This warranty does not
extend to any damage to a product caused by or attributable to freight damage, abuse, misuse, improper
or abnormal usage, or repairs not provided by an ICON authorized service center; products used for com-
mercial or rental purposes; or products used as store display models. No other warranty beyond that
specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly,
the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from province to
province.
ICON of Canada, Inc., 900 de lʼIndustrie, St. Jérôme, QC J7Y 4B8
ORDERING REPLACEMENT PARTS
T
o order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
All manuals and user guides at all-guides.com
Loading...