ProForm TREADMILL PATL30706.0, 450 CX User Manual
odel No. PATL30706.0
M
Serial No.
Serial Number
Decal
QUESTIONS?
If you have questions, or if any
parts are missing or damaged,
PLEASE CONTACT OUR CUSTOMER SERVICE DEPARTMENT
DIRECTLY.
Call toll-free:
800-830-7240
USER'S MANUAL
E-mail:
service@goodfamily.cc
Goodfamily’s Web site:
www.goodfamily.cc
ICON’s Web site:
www.iconfitness.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Goodfamily is an authorized dealer of this treadmill in the
territory of mainland China. This treadmill is designed and
manufactured by ICON
Health & Fitness, Inc.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLESHOOTING
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: T
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should be used only by persons
weighing 115 kg (275 lbs.) or less.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women.
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
When connecting the power cord (see page
10.
14), plug the power cord into an earthed circuit. No other appliance should be on the
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
11. Keep the power cord away from heated surfaces.
o reduce the risk of burns, fire, electric shock, or injury to persons, read the
12. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 25 if the treadmill is
not working properly.)
13. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 16).
14. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
16. The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
17. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
Always wear athletic
AND MOVE THE TREADMILL on page 24.)
You must be able to safely lift 20 kg (45 lbs.) to
raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the per
sonal trainer describes the change.
-
3
21. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
nd incline buttons. However, when the next
a
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
22. Always remove iFIT.com CDs and videos
from your CD player or VCR when you are not
using them.
DANGER: Always unplug the power
25.
cord immediately after use, before cleaning
he treadmill, and before performing the
t
maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
ther than the procedures in this manual
o
should be performed by an authorized service representative only.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never insert any object into any opening.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown at the right have been placed on the treadmill. If a decal is missing, or if it is not legible, call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
4
BEFORE YOU BEGIN
hank you for selecting the new PROFORM
T
readmill. The 450 CX treadmill combines advanced
t
technology with innovative design to help you get the
most from your exercise in the convenience of your
home. And when you’re not exercising, the 450 CX
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Accessory Tray
Handgrip Pulse Sensor
Handrail
Storage Latch
®
4
50 CX
ng this manual, please see the front cover of this man-
i
al. To help us assist you, please note the product
u
model number and serial number before contacting us.
The model number of the treadmill is PATL30706.0
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Key/Clip
Walking Belt
Foot Rail
BACK
Rear Roller
Adjustment Bolts
Circuit Breaker
On/Off Switch
Cushioned Walking Platform
for maximum exercise comfort
RIGHT SIDE
5
ASSEMBLY
1/2” Screw (119)–1
3/4” Tek Screw (58)–8
Nut (47)–2
Frame Bolt (32)–2
3/4” Screw (2)–12
Upright Bolt (40)–4
Upright Washer
(33)–2
Handrail Bolt (20)–4
Silver Ground
Screw (27)–2
Console Bolt
(22)–2
1/4” Star Washer
(21)–2
Handrail Star
Washer (19)–4
Upright Star
Washer (39)–4
Latch Screw
(XXX)–2
Endcap Screw
(95)–2
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated
with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the
walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there
is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own phillips screwdriver , rubber
mallet , adjustable spanner , and wire cutters .
For help identifying the assembly hardware, see the drawings below.
drawing is the key number of the part, from the PART LIST in the center of this manual. The number following the
parentheses is the quantity needed for assembly.
been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly.
The number in parentheses below each
Note: If a part is not in the parts bag, check to see if it has
6
1. Make sure that the power cord is unplugged.
dentify the Right Upright (36), which has a
I
square hole in the location shown. Slide the
ight Base Leg Cover (102) onto the Right
R
Upright.
Orient the Right Upright (36) and the Base (48)
as shown. Attach the Right Upright to the Base
with two Upright Bolts (40) and two Upright Star
Washers (39);
do not tighten the Upright Bolts
yet.
1
02
1
36
2. Orient the Left Upright (31) as shown, and slide
the Left Base Leg Cover (101) onto the Left
Upright.
Attach the Left Upright (31) to the Base (48) with
two Upright Bolts (40) and two Upright Star
Washers (39); do not tighten the Upright Bolts
yet.
Raise the Uprights (31, 36).
48
39
40
Square
Hole
2
101
36
48
31
Place an elastic band around the Right Base Leg
3.
Cover (102) and the bracket on the Right Upright
(36) as shown. Place another elastic band
around the Left Base Leg Cover (not shown) and
the bracket on the Left Upright (not shown).
Position the Base (48) near the front of the treadmill as shown.
Locate the wire in the Right Upright (36). See the
inset drawing. Tie the wire
securely to the connector on the Upright Wire (28). Then, insert the
connector into the square hole in the Right
Upright.
39
40
3
Bracket
Band
102
39
36
Wire
36
28
28
Wire
48
7
4. See the left inset drawing. Identify the two Frame
Spacers (34). Open the included packet of
rease, and apply grease to both sides of both
g
Frame Spacers. Then, identify the outer side of
ach Frame Spacer.
e
4
Hold a Frame Spacer (34) between the Right
Upright (36) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Right Upright. Attach the Right Upright to the
Lift Frame with a Frame Bolt (32), an Upright
Washer (33), and a Nut (47);
do not tighten the
Nut yet.
34
59
Outer
Side
Inner
Side
36
7
4
33
32
34
36
47
32
33
34
59
5. See the left inset drawing. Identify the outer side
of the remaining Frame Spacer (34).
Hold the Frame Spacer (34) between the Left
Upright (31) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Left Upright. Attach the Left Upright to the Lift
Frame with a Frame Bolt (32), an Upright
Washer (33), and a Nut (47);
do not tighten the
Nut yet.
5
31
47
59
32
33
34
34
Outer
31
47
Side
33
32
Inner
34
Side
59
8
6. Pull the indicated wire until the Upright Wire (28)
is extending from the upper end of the Right
pright (36). Then, disconnect and discard the
U
wire.
Remove the elastic bands from the Left and
Right Base Leg Covers (101, 102) and press
them onto the Base (48) as shown.
6
Wire
28
36
101
102
48
7. Identify the Right Handrail Endcap (91), which
does not have a cutout in the bottom, and slide it
onto the lower end of the Right Handrail (11).
Make sure that the screw hole in the Right
Handrail Endcap is at the bottom. Next, hold the
Right Handrail near the Right Upright (36), and
insert the Upright Wire (28) into the hole in the
bottom of the Right Handrail and out of the indicated hole in the top. Then, remove the tie from
the Upright Wire.
Set the Right Handrail (11) on the Right Upright
(36) while sliding the lower end of the Right
Handrail onto the bracket on the Right Upright.
Hand tighten two Handrail Bolts (20) with two
Handrail Star Washers (19) into the Right
Handrail and the Right Upright. Next, slide the
Right Handrail Endcap (91) against the Right
Upright, and tighten an Endcap Screw (95) into
the Right Handrail Endcap. Then, tighten the two
Handrail Bolts. Make sure that the Upright
Wire (28) is not pinched.
Attach the Left Handrail (18) and the Left
Handrail Endcap (90) to the Left Upright (31) as
described above.
7
20
19
Cutout
90
18
28
31
20
19
11
36
95
91
95
9
Loading...