The serial number is on a sign
behind the access panel. Write the
serial number in the space above.
Access
Panel
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
USERʼS MANUAL
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The technicians on our customer
hot line will provide immediate
assistance, free of charge.
CUSTOMER HOT LINE:
1-877-897-7493
Mon.–Fri., 8 a.m.–5 p.m. CST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
The warning sign, shown below, must be posted on a wall or fence where it will be visible to all users of the
hydrotherapy spa. Whenever the spa is moved, the sign must also be moved and reposted near the spa. If the
sign becomes lost or illegible, call our toll-free Customer Hot Line at 1-877-897-7493 to obtain a replacement
sign. Post the sign as described above.
PROFORM is a registered trademark of ICON Health & Fitness, Inc.
2
Important Safety Instructions
WARNING: To reduce the risk of drowning, electric shock, or serious injury, read the fol-
lowing important precautions before using the hydrotherapy spa.
READ AND FOLLOW ALL INSTRUCTIONS
1. It is the responsibility of the owner to ensure
that all users of the hydrotherapy spa are
adequately informed of all precautions.
2. Use the hydrotherapy spa only as described
in this manual.
3. The hydrotherapy spa is intended for home
use only. Do not use the spa in a commercial,
rental, or institutional setting.
4. Use the hydrotherapy spa only on a level surface. Do not use the spa on carpet or other
materials that could be damaged by moisture.
5. The hydrotherapy spa will weigh approximately 3,300 pounds when it is filled with
water. Make sure that the location you select
for the spa will support this weight, plus the
weight of the occupants.
6. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
7. DANGER—Risk of injury: Do not remove or
alter the covers on the suction fittings. Never
operate the hydrotherapy spa if the suction
guard is missing or broken. If you need to
replace a suction fitting or pump, make sure
you use only manufacturer recommended
replacement parts. Keep hair and body parts
away from the suction guard. Do not allow
long hair to float freely in the water; long hair
should be restrained with a bathing cap.
8. IMPORTANT: Do not allow the hydrotherapy
spa to be exposed to direct sunlight when it
is empty. The surface of the spa shell can
reach temperatures as high as 150°F in a matter of minutes if exposed to the sun while it is
empty. These high temperatures can cause
significant damage, such as blistering of the
shell surface and warping of the spa shell.
Any damage caused by sun exposure is not
covered under the warranty.
9. Do not bring any object into the hydrotherapy
spa that could damage the spa shell.
10. Never insert any object into any opening.
11. Do not use breakable containers in or near
the hydrotherapy spa.
12. Do not sit on the spa cover or place objects
on it; it is not designed to support weight.
13. Remove any water or debris that may collect
on the spa cover.
14. Keep children under the age of 12 and pets
away from the hydrotherapy spa when it is
not in use.
15. Keep all chemicals away from children and
pets.
16. The pH and chemical balance of the water
must be maintained as explained in this manual (see pages 11 and 16). Failure to do so
may cause injury to users or damage to the
hydrotherapy spa, and will void the warranty.
17. Individuals with infections and open sores or
wounds should not use the hydrotherapy
spa. Bacteria thrive in warm and hot water.
Always keep your spa disinfected and maintain the proper chemical balance.
18. Shower before and after using the hydrotherapy spa. This will remove any deodorant, perspiration, or body oils that could contaminate
the water. Showering after will remove any
residual chemicals and any bacteria that may
have been in the spa.
19. WARNING—The Ground Fault Circuit
Interrupter (GFCI), must be tested before
each use. To test the GFCI, press the “test”
button while the hydrotherapy spa is running.
The spa should shut off. Press the “reset”
button. The spa should resume normal operation. If the spa continues to run after the
“test” button is pressed, then the GFCI is
damaged. Do not use the spa until the GFCI
has been repaired or replaced by a qualified
electrician.
20. DANGER—Risk of electric shock. Keep all
3
electrical appliances such as radios, telephones, televisions, and lights at least five
feet away from the water.
1. A wire connector is provided on the electron-
2
ics pack of the hydrotherapy spa to connect a
2
minimum No. 6 AWG (13.3 mm
) solid copper
conductor between the spa and any metal
quipment, electrical enclosure made of
e
metal, metal water pipes, or conduit within
five feet of the spa.
22. DANGER—Risk of electric shock: Do not set
the hydrotherapy spa within five feet of any
metal objects or surfaces. As an alternative,
you may use the spa within five feet of metal
objects if each metal object is permanently
connected to the wire connector on the electronics pack of the spa by a minimum No. 6
2
AWG (13.3 mm
) solid copper conductor (see
instruction 21).
23. Do not operate the pump motor when the
hydrotherapy spa is empty. The pump motor
may be seriously damaged if it is operated
without water circulating.
24. DANGER—Risk of drowning: Exercise
extreme caution to prevent unauthorized and
unsupervised use of the hydrotherapy spa by
children. Children must always be supervised.
25. DANGER—To reduce the risk of drowning:
• Never use the hydrotherapy spa alone.
• Children should not use the spa unless they
are supervised by an adult.
• Keep pets away from the spa at all times.
• Always replace and lock the spa cover when
the spa is not in use.
26. WARNING—To reduce the risk of injury: The
water temperature should never exceed
104°F. Temperatures between 100°F and 104°F
are considered to be safe for healthy adults.
However, if you plan to remain in the hydrotherapy spa for more than 10 to 15 minutes, a
lower temperature is recommended. Lower
temperatures are also recommended for children. Children should not be allowed to swim
under the surface of the water in the spa.
27. WARNING—To reduce the risk of injury:
Before entering the hydrotherapy spa, always
use an accurate thermometer to determine
the water temperature.
28. WARNING—To reduce the risk of injury:
Pregnant women should consult with their
physician before using the hydrotherapy spa.
Pregnant women should not use the spa if
the water temperature is above 100°F; the
unborn child could be seriously harmed. This
is especially important during the first 90
days of the pregnancy.
29. DANGER—To reduce the risk of drowning:
Prolonged immersion in the hydrotherapy spa
ay cause hyperthermia. The causes, symp-
m
toms and effects of hyperthermia may be
described as follows: Hyperthermia occurs
when the internal temperature of the body
reaches a level several degrees above the
normal body temperature of 98.6°F. The symptoms of hyperthermia include an increase in
the internal temperature of the body, dizziness, lethargy, drowsiness and fainting. The
effects of hyperthermia include failure to perceive heat; failure to recognize the need to
exit the spa or hot tub; unawareness of
impending hazard; fetal damage in pregnant
women; physical inability to exit the spa or
hot tub and unconsciousness resulting in
danger of drowning. WARNING: The use of
alcohol, drugs or medication can greatly
increase the risk of fatal hyperthermia.
30. WARNING—To reduce the risk of drowning:
Do not use the hydrotherapy spa if you are
under the influence of alcohol or drugs. Heat
from the water, in conjunction with alcohol or
drugs, can cause loss of consciousness.
31. WARNING—To reduce the risk of injury or
drowning: Consult your physician about possible side-effects of any medications you may
be taking before using the hydrotherapy spa.
Heat from the water, in conjunction with some
medications, may cause drowsiness and
increase the risk of drowning. Other medications can effect blood pressure, heart rate,
and circulation.
32. Do not use the hydrotherapy spa immediately
after strenuous exercise.
33. If you feel pain or dizziness at any time while
using the hydrotherapy spa, discontinue use
and contact a physician.
34. WARNING—To reduce the risk of injury: It is
especially important for persons over the age
of 35 or persons with pre-existing health
problems, such as obesity, heart disease,
high or low blood pressure, circulatory problems, or diabetes to consult their physician
before using the hydrotherapy spa.
35. WARNING: The spa jets produce a stream of
4
water with relatively high pressure. Prolonged
exposure of a localized area of the body may
cause bruises to the skin.
6. The included warning sign must be posted
3
where all users of the hydrotherapy spa can
see and read it. (See POSTING THE WARNING
SIGN on page 2.)
37. WARNING DECAL PLACEMENT: Locate the
decals shown below and familiarize yourself
with the information on the decals.
WARNING: Read all instructions before using the hydrotherapy spa. ICON assumes no
responsibility for personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
5
Before You Begin
Congratulations for selecting the new PROFORM
STORM hydrotherapy spa. The innovative STORM
spa allows you to enjoy all the benefits of hydrotherapy in the comfort and privacy of your home.
Hydrotherapy is a proven method for soothing tired
muscles after exercise or for relieving the stress of a
busy life. The warm environment stimulates blood flow,
which is essential in the healing process, and the
powerful massage action further eases tension and
stress throughout the body. The PROFORM STORM
hydrotherapy spa gives you the specialized treatment
you need to feel your best.
Air
Controls
Console
Waterfall
Jet
®
Waterfall
valve
Jets
Waterfall
Valve
For your benefit, read this manual carefully before
using the hydrotherapy spa. If you have questions
after reading the manual, please call our Customer
Service Department toll-free at 1-877-897-7493,
onday through Friday, 8 a.m. until 5 p.m. Central
M
Time (excluding holidays). To help us assist you,
please mention the product model number and serial
number when calling. The model number is
PFSB63130. The serial number can be found on a
decal on the access panel inside the spa (see the front
cover of this manual).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Jets
Filter
Spa Shell
Pillow
Access
Panel
Panel
Locking
Buckle
6
Choosing a Location for the Hydrotherapy Spa
There are many factors to consider when choosing a location to set up the hydrotherapy spa. These factors vary
depending on whether you plan to use the spa inside or outside. We have listed several factors you may wish to
consider as you decide where to set up the spa.
If you set up the hydrotherapy spa inside:
1. The spa will increase the level of humidity in your
home. The location you choose should be well
ventilated. You may need to install a ventilation fan
or use a dehumidifier.
2. The spa should be located near a power source
capable of supplying 240 volts AC power. It must
be wired directly into a grounded circuit with a
Ground Fault Circuit Interrupter (GFCI) capable of
carrying 45 amps. No other appliance should be
on the same circuit.
3. The spa should be close to a source of water.
4. Do not use the spa on carpet or other material that
may be damaged by moisture. We recommend
that you place the spa on a water- and stain-resistant, non-slip surface with a floor drain for any
water that may splash from the spa.
5. Make sure that the location you choose is stable. It
must be able to support the weight of the spa
when it is filled with water, plus the weight of the
occupants. The spa weighs approximately 3,300
pounds when it is filled with water.
If you set up the hydrotherapy spa outside:
1. Check local building codes concerning the use of
outdoor spas.
2. The spa should be located near a power source
capable of supplying 240 volts AC power. It must
be wired directly into a grounded circuit with a
Ground Fault Circuit Interrupter (GFCI) capable of
carrying 45 amps. No other appliance should be
on the same circuit.
3. The spa should be close to a source of water.
4. We recommend that you place the spa on a waterand stain-resistant, non-slip surface. Do not use
the spa on rough or sharp surfaces such as gravel
or wood chips.
5. Make sure that the location you choose is stable. It
must be able to support the weight of the spa
when it is filled with water, plus the weight of the
occupants. The spa weighs approximately 3,300
pounds when it is filled with water.
6. Consider environmental factors such as rain, wind,
shade, and sunlight.
6. Do not use the spa above a finished living area,
due to the risk of water damage.
7. Make sure that there is room around the spa to
permit servicing of the unit. The dimensions of the
spa are 84” W x 84” L x 36” H. You should allow for
this size when choosing the location.
8. The spa is not designed for in-floor installation.
However, it is compatible with a deck system that
is built flush with the top of the spa, provided you
leave access to the motor for service.
9. Make sure to note any other considerations, such
as aesthetics or privacy concerns, that may affect
the safety or enjoyment of using the spa.
7. You should be able to monitor the use of the spa
from your home, to prevent unauthorized use by
children. You may want to enclose the spa with a
fence and self-latching gate to prevent unauthorized use.
8. Make sure that there is room around the spa to
permit servicing of the unit. The dimensions of the
spa are 84” W x 84” L x 36” H. You should allow for
this size when choosing the location.
9. The spa is not designed to be installed below
ground level. However, it is compatible with a deck
system that is built flush with the top of the spa,
provided you leave access to the motor for service.
10.Make sure to note any other considerations, such
as aesthetics or privacy concerns, that may affect
the safety or enjoyment of using the spa.
7
Assembly
efore beginning assembly, carefully read the
B
following information and instructions:
• Place all parts in a cleared area and remove the
acking materials from the spa shell. Do not dis-
p
pose of the packing materials until assembly is
completed and the spa is operating.
• During assembly, make sure that all parts are
oriented as shown in the drawings.
• Read each assembly step before you begin.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Before beginning assembly, make sure that you
have read and understand the information in the
above and on the previous two pages.
Remove the four #10 x 2” Machine Screws (46) that
secure the indicated Access Panel (25) to the spa.
Carefully remove the Access Panel and set it aside.
Be careful not to damage the spa shell.
SSEMBLY REQUIRES THE FOLLOWING
A
TOOLS (not included):
• One phillips screwdriver
A wire connector is provided on the electronics
pack of the spa to connect a minimum No. 6
AWG (13.3 mm
between the spa and any metal equipment,
electrical enclosure made of metal, metal water
pipes, or conduit within five feet of the spa.
1
2
) solid copper conductor
Spa Shell
2. Close the valve knob on the drain hose. Thread the
cap onto the drain hose.
Locate the four gate valves inside the access opening (there are two gate valves per pump). Make sure
that the gate valves are open and that the locking
clips are snapped onto the stems of the gate valves,
as shown in the inset drawing.
Make sure that the six collars are tightened (there
are two collars per pump and two on the heater).
Refer to step 1. Re-attach the Access Panel (25) to
the spa.
46
25
2
Locking Clip
46
Gate Valve
Drain
Hose
Collar
Cap
Valve
Knob
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.