This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, see
the front cover of this manual and request a
free replacement decal. Apply the decal in the
location shown. Note: The decal(s) may not be
shown at actual size.
PROFORM is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your rower before using your rower. ICON assumes
no responsibility for personal injury or property damage sustained by or through the use of this
product.
1. It is the responsibility of the owner to ensure
that all users of the rower are adequately
informed of all precautions.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
3. Use the rower only as described in this
manual.
4. The rower is intended for home use only. Do
not use the rower in a commercial, rental, or
institutional setting.
5. Keep the rower indoors, away from moisture
and dust. Do not put the rower in a garage or
covered patio, or near water.
6. Place the rower on a level surface, with a mat
beneath it to protect the floor or carpet. Make
sure that there is at least 2 ft. (0.6 m) of clearance around the rower.
7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
8. Keep children under age 12 and pets away
from the rower at all times.
9. Wear appropriate clothes while exercising;
do not wear loose clothes that could become
caught on the rower. Always wear athletic
shoes for foot protection.
10. The rower should not be used by persons
weighing more than 253 lbs. (115 kg).
11. Always keep your back straight while using
the rower; do not arch your back.
12. Do not release the row bar while the cord is
extended.
13. Over exercising may result in serious injury
or death. If you feel faint, if you become short
of breath, or if you experience pain while
exercising, stop immediately and cool down.
3
BEFORE YOU BEGIN
Thank you for selecting the new PROFORM® R 600
rower. Rowing is an effective exercise for increasing
cardiovascular fitness, building endurance, and toning
the body. The R 600 rower is designed to let you enjoy
this effective exercise in the convenience and privacy
of your home.
For your benefit, read this manual carefully before
you use the rower. If you have questions after reading
Length: 7 ft. 3 in. (220 cm)
Width: 1 ft. 10 in. (56 cm)
Weight: 86 lbs. (39 kg)
Frame Handle
Seat
Resistance Handle
Row Bar
Console
this manual, please see the front cover of this manual.
To h e lp us as s is t y o u, no t e t he pr od uc t m o de l n u mb e r
and serial number before contacting us. The model
number and the location of the serial number decal are
shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Strap
Wheel
Footrest
Rail
Rail Handle
Folding Clamp
4
ASSEMBLY
• Assembly requires two persons.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you fi nish all assembly steps.
1. Go to www.iconsupport.eu on your computer
and register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Service
• allows us to notify you of upgrades and offers
Note: If you do not have Internet access, call
Customer Service (see the front cover of this
manual) and register your product.
• Assembly requires the following tool(s):
one Phillips screwdriver
one adjustable wrench
To a v oi d d a ma g in g p a rt s , d o n ot us e po w er to o ls .
1
2. If there are shipping tubes (not shown) attached
to the rower, remove and discard the shipping
tubes and the hardware attaching them.
With the help of a second person, pull the
Rail (2) outward and rotate the Stabilizer (3)
downward.
2
3
2
5
3. Have a second person hold the Rail (2) dur-
ing this step.
Attach the Stabilizer (3) to the Frame (1) with
two M10 x 20mm Screws (61).
Then, hold the Rail Handle (34), pull the Rail (2)
outward, and set the Rail on the floor.
3
4. Orient the Seat (23) as shown, and slide the
Seat Carriage (5) onto the Rail (2).
2
1
3
34
61
4
23
2
5
6
5. Slide the Seat (23) to the front of the Rail (2).
Next, attach a Stop (32) to each side of the Rail
(2) with an M4 x 19mm Screw (69).
Then, attach the Rail Cap (38) to the Rail (2)
with two M4 x 19mm Screws (69).
5
38
69
69
32
2
23
32
69
69
6. The Console (51) requires four AA batteries (not
included); alkaline batteries are recommended.
Do not use old and new batteries together or
alkaline, standard, and rechargeable batteries together. IMPORTANT: If the Console has
been exposed to cold temperatures, allow
it to warm to room temperature before you
insert batteries. Otherwise, you may damage the console display or other electronic
components.
Remove the screw (A) and the battery cover (B)
from the top of the Console (51). Then, pull out
the battery holder (C) and insert batteries (D)
into the battery holder; make sure to orient the
batteries as shown by the diagram inside the
battery holder. Then, reinsert the battery holder
and reattach the battery cover.
See the inset drawing. Make sure that the
batteries (D) are facing upward and that the
contacts (E) on the batter holder (C) are facing
downward when you insert the battery holder.
6
D
C
B
A
E
51
D
C
E
7. Make sure that all parts are properly tightened before you use the rower. Extra parts may be included.
Place a mat under the rower to protect the floor.
7
HOW TO USE THE ROWER
HOW TO ADJUST THE RESISTANCE
To vary the
intensity of your
exercise, you
can adjust the
resistance that
you feel when
you pull the row
bar. To increase the resistance,
move the resistance handle
toward the front
of the rower; to
decrease the
resistance, move the resistance handle toward the
rear of the rower.
HOW TO ADJUST THE FOOT PADS
First, sit on the seat and place your feet in the foot
pads.
Next, press the
footrest bracket,
slide the foot pad
to the desired
position, and
then release the
footrest bracket
so that the tab
engages a slot
in the foot pad.
Then, tighten the
strap over your foot.
Adjust the other foot pad in the same way. Make
sure to adjust both foot pads to the same position.
Handle
Bracket
Ta b
Pad
HOW TO MOVE THE ROWER IN THE UNFOLDED
POSITION
Stand behind
the rower and lift
the rail until the
rower will roll on
the wheels. Then,
carefully move
the rower to the
desired location,
and lower the rail
to the floor.
HOW TO MOVE THE ROWER IN THE FOLDED
POSITION
See HOW TO FOLD AND STORE THE ROWER on
page 9, and fold the rower. Then, hold the frame
handle, place your foot on a stabilizer foot, and tip the
rower until it will roll on the wheels. Carefully move the
rower to the desired location, and then tip it into the
storage position.
Place
your foot
here
Lift
here
Handle
8
HOW TO FOLD AND STORE THE ROWER
The rower can be stored in a folded position to conserve space. Store the rower in a location where
children cannot tip it. Remove the batteries from the
console when storing the rower for extended periods of
time.
To store the rower, first slide the Seat (23) to the rear of
the Rail (2).
Then, pull the Rail Handle (34) inward until the Folding
Clamp (35) engages the bar on the Stabilizer (3).
52
2
7, 8
43
52
23
3
2
34
Next, hold and lift the Frame Handle (52) and the Rail
Handle (34), and tip the rower forward onto the Shields
(7, 8) and the Storage Feet (43).
34
35
3
41
41
To u n fo l d t he ro w er , f ir s t p la c e y ou r fo o t o n a S t ab i li z er
Foot (41) and pull the Rail Handle (34) outward to disengage the Folding Clamp (35).
Then, hold the Rail Handle (34) and the Frame Handle
(52), pull the Rail Handle outward, and lower the Rail
(2) to the floor.
9
HOW TO ROW ON THE ROWER
Sit on the seat, place your feet in the footrests, and
adjust the straps to fit your feet. Then, hold the row bar
with an overhand grip.
Correct rowing form consists of three phases:
at the waist), keeping your back straight. As you
straighten your legs, pull the row bar toward your
chest. Keep your elbows outward.
3. The third phase is the FINISH. Your legs should
be nearly straight. Continue to pull the row bar until
your hands are even with your chest.
1. The first phase is the CATCH. Slide the seat
forward until your knees are almost touching your
chest. Pull the row bar until your hands are above
your feet.
2. The second phase is the DRIVE. Push backward
with your legs. Lean back slightly at the hips (not
After the finish phase, extend your arms forward and
pull the seat forward using your legs. Repeat this
sequence, moving through all three phases with a
smooth, fluid motion. Remember to breathe normally
as you row; never hold your breath.
10
HOW TO USE THE CONSOLE
FEATURES OF THE CONSOLE
The easy-to-use console features several modes that
provide instant exercise feedback during your workouts. The modes are described below.
HOW TO USE THE CONSOLE
Make sure that batteries are installed in the console
(see assembly step 6 on page 7). If there is a sheet
of clear plastic on the console, remove the plastic.
1. Turn on the console.
To t u rn on th e c o ns o le , p r es s t h e On /R e se t b u tt o n
on the console or simply begin rowing.
2. Begin rowing and follow your progress with the
displays.
Upper display—This display will show the watts
mode and the strokes per minute mode.
Center display—This display will show the time
mode and the strokes mode.
Lower display—This display will show the calories
mode.
The scan mode will be selected automatically when
you turn on the console.
Watts—This mode shows your approximate power
output in watts.
Strokes Per Minute (SPM)—This mode shows the
number of rowing strokes you are completing per
minute.
Time—This mode shows the elapsed time.
Strokes—This mode shows the number of rowing
strokes you have completed during your workout.
Calories—This mode shows the approximate number
of calories you have burned during your workout.
Scan—This mode shows the watts, strokes per minute, time, and strokes modes for a few seconds each in
a repeating cycle.
To view the watts, strokes per minute, time, or
strokes mode for continuous display, press the
Priority Display button repeatedly until the desired
mode is shown in the display.
To return to the scan mode, press the Priority
Display button repeatedly until the word SCAN
appears in the center display.
To reset the displays to zero, press the On/Reset
button.
3. When you are finished exercising, the console
will turn off automatically.
If the row bar does not move for a few seconds, the
console will pause.
The console has an auto-off feature. If the row bar
does not move and the console buttons are not
pressed for a few minutes, the power will turn off
automatically to save the batteries.
11
MAINTENANCE AND TROUBLESHOOTING
MAINTENANCE
Inspect and tighten all parts of the rower regularly.
Replace any worn parts immediately.
To c l ea n t h e r ow e r, u s e a d a mp cl o th a nd a s ma l l
amount of mild detergent. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
For best results, clean the rail, the seat carriage, and
the carriage rollers daily.
CONSOLE TROUBLESHOOTING
Most console problems are the result of low batteries;
for replacement instructions, see assembly step 6 on
page 7.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted.
Next, see the EXPLODED DRAWING on page 15.
Locate the Right and Left Shields (7, 8), and remove
the four M4 x 19mm Screws (69) and the ten M4 x
16mm Screws (68) from the Right and Left Shields.
Then, gently remove the Right and Left Shields.
Locate the Reed Switch (47). Turn the Left Fan (4) until
a Magnet (77) is aligned with the Reed Switch. Loosen,
but do not remove, the two indicated M4 x 19mm
Screws (69). Then, slide the Reed Switch slightly
closer to or away from the Magnet, and retighten the
Screws.
47
4
To a d ju s t t he re e d s wi t ch , y o u m us t re m ov e t h e
resistance handle and the right and left shields as
described below.
First, remove the
six M4 x 10mm
Screws (70),
and then gently remove the
Resistance
Handle (9).
70
9
70
77
69
Turn the Left Fan (4) so that the Magnet (77) passes
the Reed Switch (47) repeatedly. Repeat these actions
until the console displays correct feedback.
When the reed switch is correctly adjusted, reattach
the parts that you removed.
12
EXERCISE GUIDELINES
WARNING: Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To f i nd th e p r op e r i nt e ns i ty le v el , fi n d y ou r a g e a t t he
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
HOW TO MEASURE YOUR HEART RATE
To m e as u re yo u r h ea r t
rate, exercise for at least
four minutes. Then, stop
exercising and place
two fingers on your
wrist as shown. Take a
six-second heartbeat
count, and multiply the
result by 10 to find your heart rate. For example, if your
six-second heartbeat count is 14, your heart rate is 140
beats per minute.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretch-
ing and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To m a in t ai n o r i m pr o ve yo u r c on d it io n, co m pl e te th r ee
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
13
PART LIST
K e y N o . Q t y . D e s c r i p t i o n K e y N o . Q t y . D e s c r i p t i o n
Model No. PFEVRW49715.0 R0215A
1 1 Frame
2 1 Rail
3 1 Stabilizer
4 1 Left Fan
5 1 Seat Carriage
6 2 Deflector
7 1 Right Shield
8 1 Left Shield
9 1 Resistance Handle
10 1 Grommet
11 1 Bungee Cord
12 1 Strap
13 1 Row Bar
14 2 Grip
15 2 Row Bar Cap
16 2 Footrest Strap
17 1 Right Footrest
18 1 Right Foot Pad
19 1 Right Footrest Bracket
20 1 Left Footrest Bracket
21 1 Left Footrest
22 1 Left Foot Pad
23 1 Seat
24 2 Set Screw
25 2 Snap Ring
26 1 Hub
27 2 Bearing
28 1 Bearing Spacer
29 1 Pulley Assembly
30 1 Axle
31 2 Pivot Bushing
32 4 Stop
33 1 Bumper
34 1 Rail Handle
35 1 Folding Clamp
36 2 Rail Foot
37 2 Small Carriage Roller
38 1 Rail Cap
39 2 Large Carriage Roller
40 2 Carriage Axle
Note: Specifi cations are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
14
EXPLODED DRAWING
Model No. PFEVRW49715.0 R0215A
68
72
69
60
75
68
31
31
73
58
42
2
66
43
32
24
33
42
11
69
73
61
69
34
69
32
69
69
35
75
67
5
41
3
63
69
40
62
63
39
36
57
56
62
37
38
6
70
32
68
69
25
30
63
62
44
54
64
49
68
29
27
28
7
76
54
68
54
57
76
56
54
76
50
10
47
69
48
1
9
70
54
76
76
54
8
54
68
13
14
12
65
57
56
69
44
58
17
56
55
59
57
44
23
65
65
19
65
18
6
69
77
4
15
71
74
26
24
25
16
27
46
63
69
62
57
45
56
44
55
52
57
20
51
44
21
22
53
58
59
15
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
RECYCLING INFORMATION
This electronic product must not be disposed of in municipal waste. To
preserve the environment, this product must be recycled after its useful life
as required by law.
Please use recycling facilities that are authorized to collect this type of waste in
your area. In doing so, you will help to conserve natural resources and improve
European standards of environmental protection. If you require more information
about safe and correct disposal methods, please contact your local city office or the
establishment where you purchased this product.