Model No. PFEVEX73108.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer
satisfaction. If you have questions,
or if there are missing parts, please
contact us:
USER'S MANUAL
Call: 08457 089 009
Outside UK: 0 (44) 113 3877133
Fax: 0 (44) 113 3877125
E-mail: csuk@iconeurope.com
Write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road, Beeston
Leeds, LS11 8JG
UK
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
EFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
B
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
OW TO USE THE EXERCISE CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
H
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the warning
decal(s). If a decal is missing or illegible, call
the telephone number on the front cover of
this manual and request a free replacement
decal. Apply the decal in the location shown.
Note: The decal(s) may not be shown at actual
size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your exercise cycle before using your exercise
cycle. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the exercise cycle are adequately informed of all precautions.
3. Your exercise cycle is intended for home use
only. Do not use your exercise cycle in a
commercial, rental, or institutional setting.
4. Keep your exercise cycle indoors, away from
moisture and dust. Place your exercise cycle
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around your exercise cycle to mount, dismount, and use it.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your exercise cycle at all times.
8. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
9. Wear appropriate exercise clothes while
exercising; do not wear loose clothes that
could become caught on your exercise
cycle. Always wear athletic shoes for foot
protection while exercising.
10. Keep your back straight while using your
exercise cycle; do not arch your back.
11. When you stop exercising, allow the pedals
to slowly come to a stop.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. Use your exercise cycle only as described in
this manual.
7. Your exercise cycle should not be used by
persons weighing more than 265 lbs.
(120 kg).
3
BEFORE YOU BEGIN
ongratulations for selecting the new PROFORM
C
ZLX exercise cycle. Cycling is one of the most effective exercises for increasing cardiovascular fitness,
building endurance, and toning the body. The 280 ZLX
xercise cycle offers a selection of features designed
e
to let you enjoy this healthful exercise in the convenience and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
Handlebar
Console
®
80
2
fter reading this manual, please see the front cover
a
of this manual. To help us assist you, note the product
model number and serial number before contacting
us. The model number and the location of the serial
umber decal are shown on the front cover of this
n
manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Pulse Sensor
Seat
Seat Knob
Seat Post Knob
Leveling Cap
Pivot Handle
Pedal/Strap
4
M8 Split
Washer (42)–3
M4 x 15mm
Screw (48)–5
M8 x 16mm Patch
Screw (34)–3
M10 x 70mm Patch Screw (33)–2
M8 x 60mm Patch Screw (30)–4
ASSEMBLY
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the pack-
ing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver , an adjustable
rench , and pliers .
w
Use the drawings below to identify the small parts used in assembly. The number in parentheses below each
drawing is the key number of the part, from the PART LIST near the end of this manual. The second number is
the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in
the hardware kit, check to see if it has been preassembled.
5
1.
To make assembly easier, read the
information on page 5 before you begin
ssembling the exercise cycle.
a
Insert the Rear Stabilizer (6) into the Frame (1).
ttach the Rear Stabilizer (6) with four M8 x
A
60mm Patch Screws (30).
1
1
6
30
2. Orient the Front Stabilizer (2) so that the large
holes face the Frame (1).
Attach the Front Stabilizer (2) with two M10 x
70mm Patch Screws (33).
2
33
1
Large
2
Holes
6
3. While another person holds the Upright (13)
near the Frame (1), connect the Upper Wire
Harness (23) to the Lower Wire Harness (68).
Insert the excess wire downward into the Frame
1).
(
Tip: Avoid pinching the wires. Insert the
Upright (13) into the Frame (1). Attach the
Upright with three M8 x 16mm Patch Screws
(34) and three M8 Split Washers (42).
3
13
Avoid pinching
the wires
23
4. While another person holds the Handlebar (50)
near the Upright (13), insert the Pulse Wires
(59) into the Upright and pull them upward out
of the top of the Upright.
Tip: Avoid pinching the wires. Attach the
Handlebar (50) to the Upright (13) with the Pivot
Clamp (54), the Rear Cover (3), and the Pivot
Handle (55).
Note: The Pivot Handle (55) functions like a
ratchet. Turn the Pivot Handle clockwise, pull it
away from the Upright (13), turn it counterclockwise, push it toward the Upright, and then turn it
clockwise again. Repeat this process until the
Pivot Handle is tight.
34
42
4
13
34
1
Avoid pinching
the wires
23
54
3
Attach the Rear Cover (3) to the Upright (13)
with an M4 x 15mm Screw (48).
7
5. The Console (16) requires four AA batteries (not
included); alkaline batteries are recommended.
IMPORTANT: If the Console has been
xposed to cold temperatures, allow it to
e
warm to room temperature before inserting
atteries. Otherwise, you may damage the
b
console displays or other electronic components. Remove the screw, remove the battery
cover, and insert the batteries into the battery
compartment. Then, reattach the battery cover.
Make sure to orient the batteries as shown
by the diagram inside the battery compartment.
5
Screw
Battery
over
C
Batteries
6. While another person holds the Console (16)
near the Upright (13), connect the console wire
to the Upper Wire Harness (23). Next, connect
the console pulse wires to the Pulse Wires (59).
Insert the excess wire downward into the
Upright (13).
Tip: Avoid pinching the wires. Attach the
Console (16) to the Upright (13) with four M4 x
15mm Screws (48).
6
16
Pulse
Wires
59
Console
Wire
8
7. Loosen and remove the Seat Knob (56) from
the Seat Carriage (58), which is located on the
underside of the Seat (12).
7
See the inset drawing. Look underneath the
eat (12) and locate the Seat Block (57) inside
S
the Seat Carriage (58).
Set the Seat Carriage (58) in the bracket on the
Seat Post (5). Next, insert the Seat Knob (56)
upward through the bracket on the Seat Post
into the hole in the Seat Block (57). Then, tighten the Seat Knob.
8. Loosen and remove the Seat Post Knob (9)
from the Frame (1).
Insert the Seat Post (5) into the Frame (1).
Adjust the Seat Post to the desired height and
insert the Seat Post Knob (9) through the indicated hole in the Frame into one of the
adjustment holes in the Seat Post.
12
8
5
57
5
12
58
8
57
56
Tighten the Seat Post Knob (9). Make sure that
the Seat Post Knob is firmly engaged in one
of the adjustment holes in the Seat Post (5).
Adjustment
Holes
5
1
Hole
9
9
9. Identify the Left Pedal (24), which is marked
with an “L.” Using an adjustable wrench, firmly
tighten the Left Pedal
eft Crank Arm (66).
L
counterclockwise
into the
9
ighten the Right Pedal (not shown)
T
into the right arm of the Crank (not shown).
IMPORTANT: Tighten both pedals as firmly
as possible. After using the exercise cycle
for one week, retighten the pedals. For best
performance, keep the pedals tightened.
Adjust the strap on the Left Pedal (24) to the
desired position, and press the end of the strap
onto the tab on the side of the Left Pedal.
Adjust the strap on the Right Pedal (not
shown) in the same way.
10. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly
is completed, some extra parts may be left over. Place a mat beneath the exercise cycle to protect the floor.
lockwise
c
S
trap
Tab
66
10
HOW TO USE THE EXERCISE CYCLE
HOW TO ADJUST THE SEAT POST
or effective exercise, the seat should be at the prop-
F
er height. As you pedal, there should be a slight bend
in your knees when the pedals are in the lowest position.
To adjust the height
of the seat, first
loosen and remove
the seat post knob.
Next, slide the seat
post upward or
downward and
align one of the
adjustment holes in
the seat post with
the indicated hole
in the frame. Insert
the seat post knob
into the frame and
the seat post, and
then tighten the
seat post knob. Make sure that the seat post knob
is inserted through one of the adjustment holes in
the seat post.
HOW TO ADJUST THE SEAT
To adjust the horizontal position of
the seat, loosen
the seat knob
under the seat,
slide the seat forward or backward
to the desired position, and then
retighten the seat
knob.
Seat
Seat Post
Hole
Seat Post
Knob
Seat
Seat Knob
HOW TO LEVEL THE EXERCISE CYCLE
f the exercise cycle
I
rocks on your floor
during use, turn one
or both of the leveling caps until the
rocking motion is
eliminated.
HOW TO ADJUST THE ANGLE OF THE
HANDLEBAR
To adjust the angle
of the handlebar,
loosen the pivot
handle, rotate the
handlebar to the
desired angle, and
then retighten the
pivot handle. Note:
The pivot handle
functions like a
ratchet. Turn the
pivot handle clockwise, pull it away
from the upright, turn it counterclockwise, push it
toward the upright, and then turn it clockwise again.
Repeat this process until the pivot handle is tight.
Leveling
Caps
Pivot
Handle
11
ONSOLE DIAGRAM
C
Resistance Dial
FEATURES OF THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable. When you select the manual mode of the
console, you can change the resistance of the pedals
with a touch of the dial. As you exercise, the console
will provide continuous exercise feedback. You can
even measure your heart rate using the handgrip
pulse sensor.
The console offers sixteen preset workouts. Each
workout automatically changes the resistance of the
pedals and prompts you to increase or decrease your
pedaling pace as it guides you through an effective
workout.
IMPORTANT: Before you use the console for the
first time, you must select BIKE or ELLIPTICAL; if
you do not do this, the console will not display
correct feedback. (See HOW TO ENTER CONSOLE
SETTINGS on page 13.)
To enter console settings, see page 13. To use the
manual mode, see page 14. To use a preset workout, see page 16.
Note: If there is a sheet of clear plastic on the face of
the console, remove the plastic.
12
HOW TO ENTER CONSOLE SETTINGS
1. Begin pedaling or press any button on the console to turn on the console.
moment after you begin pedaling or press a but-
A
ton, the display will light.
2. Select the user mode.
The user mode allows you to select the type of
product that the console is operating, select a unit
of measurement for an exercise cycle, and select
a backlight option for the console.
To select the user mode, press and hold the resistance dial (see the drawing on page 12) for
several seconds until the words BIKE and ELLIPTICAL appear in the display.
3. Select BIKE or ELLIPTICAL as the product
type.
The arrow in the display indicates the currently
selected product type. To change the selection,
press the Display button repeatedly.
4. If the console is operating an exercise cycle,
select a unit of measurement.
When the console operates an exercise cycle, the
console can show speed and distance in either
iles or kilometers.
m
If you selected BIKE as the product type, the word
ENGLISH (for English miles) or the word METRIC
(for metric kilometers) will appear in the display to
show which unit of measurement is selected.
If the console is operating an exercise cycle,
select BIKE as the product type. If the console is
operating an elliptical exerciser, select ELLIPTI-
CAL as the product type.
Then, press the Workout button to save your
selection. The other console settings will then
appear in the display.
IMPORTANT: If you selected BIKE, go to step 4.
If you selected ELLIPTICAL, go to step 5.
To change the unit of measurement, turn the resistance dial until the desired unit of measurement
appears in the display.
5. Select a backlight option, if desired.
The console has three backlight options. The ON
option keeps the backlight on while the console is
on. The AUTO option keeps the backlight on only
while you are pedaling. The OFF option turns the
backlight off.
To select a backlight option, press the Display button repeatedly until the desired backlight option
appears in the display.
6. Exit the user mode.
Press the Workout button to save the console settings and exit the user mode.
13
HOW TO USE THE MANUAL MODE
1. Begin pedaling or press any button on the console to turn on the console.
A moment after you begin pedaling or press a button, the display will light.
2. Select the manual mode.
Each time you turn
on the console, the
manual mode will
be selected. If you
have selected a
workout, reselect
the manual mode
by pressing the Workout button repeatedly until
the word MANUAL appears in the lower left corner
of the display.
3. Begin pedaling and change the resistance of
the pedals as desired.
The lower left corner of the display will show
the distance you have pedaled.
Note: If the console is operating an exercise cycle,
the distance will be shown in miles or kilometers. If
the console is operating an elliptical exerciser, the
distance will be shown in total number of revolutions.
The upper right corner of the display will show
the approximate number of calories you have
burned. The upper right corner of the display will
also show your heart rate when you use the handgrip pulse sensor (see step 5 on page 15).
The lower right corner of the display will show
your pedaling pace.
Note: If the console is operating an exercise cycle,
your pedaling pace will be shown in miles per hour
or kilometers per hour. If the console is operating
an elliptical exerciser, your pedaling pace will be
shown in revolutions per minute (rpm).
As you pedal, change the resistance of the pedals
by turning the resistance dial. To increase the
resistance, turn the resistance dial clockwise; to
decrease the resistance, turn the resistance dial
counterclockwise. Note: After you change the
resistance, it will take a moment for the pedals to
reach the selected resistance level.
4. Follow your progress with the display.
The upper left corner of the display will show
the elapsed time. Note: When a preset workout is
selected, the display will show the time remaining
in the workout instead of the elapsed time.
The center of the display will show the resistance level of the pedals for a few seconds each
time the resistance level changes.
You can also view selected information at a larger
size. Press the Display button repeatedly to view
time and distance information, time and calorie
information, or time and pace information. Press
the Display button again to view all information.
14
5. Measure your heart rate if desired.
If there are sheets
f clear plastic on
o
the metal contacts on the
handgrip pulse
ensor, remove
s
the plastic. To
measure your heart
rate, hold the handgrip pulse sensor
with your palms
resting against the
metal contacts. Avoid moving your hands or
gripping the contacts too tightly.
When your pulse is detected, one, two, or three
dashes will appear in the display, and then your
heart rate will be shown. For the most accurate
heart rate reading, hold the contacts for at least 15
seconds. Note: If you continue to hold the handgrip pulse sensor, the display will show your heart
rate for up to 30 seconds.
Contacts
If the display does not show your heart rate, make
sure that your hands are positioned as described.
Be careful not to move your hands excessively or
o squeeze the metal contacts too tightly. For opti-
t
mal performance, clean the metal contacts using a
soft cloth; never use alcohol, abrasives, or
chemicals to clean the contacts.
6. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for several seconds, a
tone will sound, the console will pause, and the
time will flash in the display.
If the pedals do not move for several minutes and
the buttons are not pressed, the console will turn
off and the display will be reset.
15
OW TO USE A PRESET WORKOUT
H
. Begin pedaling or press any button on the con-
1
sole to turn on the console.
A moment after you begin pedaling or press a but-
on, the display will light.
t
2. Select a preset workout.
To select a preset
workout, press the
Workout button
repeatedly until the
number of the
desired workout
appears in the display. The workout
time and a profile of the resistance levels for the
workout will also appear in the display.
3. Begin pedaling to start the workout.
Each workout is divided into several one-minute
segments. One resistance level and one target
pace (speed) are programmed for each segment.
Note: The same resistance level and/or target
pace may be programmed for consecutive segments.
The workout profile will show your progress (see
the drawing above). The flashing segment of the
profile represents the current segment of the workout. The height of the flashing segment indicates
the resistance level for the current segment.
When the first segment of the workout ends, a
tone will sound and the resistance level and the
target pace for the second segment will appear in
the center of the display for a few seconds to alert
you. The next segment of the profile will begin to
flash, and the pedals will automatically adjust to
the resistance level for the next segment.
Profile
s you exercise,
A
you will be prompt-
d to keep your
e
pedaling pace near
the target pace for
the current seg-
ent. When an
m
upward arrow appears in the display, increase
your pace. When a downward arrow appears,
decrease your pace. When no arrow appears,
maintain your current pace.
IMPORTANT: The target pace is intended only
to provide motivation. Your actual pace may be
slower than the target pace. Make sure to
pedal at a pace that is comfortable for you.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by turning the resistance dial. IMPOR-
TANT: When the current segment of the
workout ends, the pedals will automatically
adjust to the resistance level for the next segment.
The workout will continue in this way until the last
segment ends. To stop the workout at any time,
stop pedaling. A tone will sound and the time will
begin to flash in the display. To restart the workout,
simply resume pedaling.
4. Follow your progress with the display.
See step 4 on page 14.
5. Measure your heart rate if desired.
See step 5 on page 15.
6. When you are finished exercising, the console
will turn off automatically.
See step 6 on page 15.
16
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the exercise cycle regularly. Replace any worn parts immediately.
To clean the exercise cycle, use a damp cloth and a
small amount of mild detergent. IMPORTANT: To
avoid damage to the console, keep liquids away
from the console and keep the console out of
direct sunlight.
CONSOLE TROUBLESHOOTING
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
assembly step 5 on page 8. If the handgrip pulse sensor does not function properly, see step 5 on page 15.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, the left pedal and the left shield must be
removed.
Using an adjustable wrench, turn the left pedal clockwise and remove it. Next, remove all of the screws
from both shields; there are two sizes of screws in
the shields—note which size of screw you remove
from each hole. Then, carefully remove the left shield.
Locate the Reed Switch (39). Turn the Left Crank Arm
(66) until a Magnet (38) is aligned with the Reed
Switch. Loosen, but do not remove, the M5 x 15mm
Screw (47). Slide the Reed Switch slightly closer to or
away from the Magnet, and then retighten the Screw.
Turn the Left Crank Arm for a moment. Repeat until
the console displays correct feedback.
38
39
47
When the Reed Switch is correctly adjusted, reattach
the shields and the left pedal.
66
17
HOW TO ADJUST THE BELT
If you can feel the pedals slip while you are pedaling,
ven when the resistance is at the highest level, the
e
belt may need to be adjusted. To adjust the belt, the
edals and the shields must be removed.
p
Use an adjustable wrench to remove the pedals. To
remove the left pedal, turn the left pedal clockwise; to
remove the right pedal, turn the right pedal counterclockwise.
Next, remove all of the screws from both shields; there
are two sizes of screws in the shields—note which
size of screw you remove from each hole. Then,
carefully remove the shields.
Next, loosen the 3/8" Nuts (27), which are located on
each side of the Flywheel (37). Then, tighten the M6
Locknuts (32), one on each side of the Flywheel, until
he Belt (35) is properly tightened.
t
27
35
27
32
37
32
Finally, tighten the 3/8" Nuts (27) and reattach the
shields and the pedals.
18
EXERCISE GUIDELINES
WARNING: Before beginning
his or any exercise workout, consult your
t
physician. This is especially important for
persons over the age of 35 or persons with
pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
These guidelines will help you to plan your exercise
workout. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses
the first few minutes of exercise does your body begin
to use stored
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
carbohydrate calories
fat calories
for energy. If your goal is to
for energy. Only after
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
WORKOUT GUIDELINES
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise workout, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
19
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
ove slowly as you stretch—never bounce.
M
. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
1
2
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
20
NOTES
21
PART LIST—Model No. PFEVEX73108.0 R0908A
Key No. Qty. Description Key No. Qty. Description
11Frame
21Front Stabilizer
31Rear Cover
4
51Seat Post
61Rear Stabilizer
72Handlebar Cap
82Leveling Cap
91Seat Post Knob
10 4 M8 Locknut
11 1 Idler
12 1 Seat
13 1 Upright
14 1 Left Front Cover
15 1 Right Front Cover
16 1 Console
17 1 Left Shield
18 1 Right Shield
19 1 Resistance Motor
20 1 Seat Post Bushing
21 1 Crank/Pulley
22 1 Reed Switch Clamp
23 1 Upper Wire Harness
24 1 Left Pedal/Strap
25 1 Spring
26 1 Right Pedal/Strap
27 2 3/8" Nut
28 2 U-bracket
29 1 Resistance Cable
30 4 M8 x 60mm Patch Screw
31 2 Eyebolt
32 2 M6 Locknut
33 2 M10 x 70mm Patch Screw
34 3 M8 x 16mm Patch Screw
35 1 Belt
2 Front Stabilizer Cap
36 2 Crank Bearing
37 1 Flywheel
38 2 Magnet
9 1 Reed Switch/Wire
3
40 1 M8 x 20mm Bolt
41 6 M4 x 25mm Screw
42 7 M8 Split Washer
43 2 Flywheel Nut
44 4 M5 x 12mm Button Screw
45 1 M8 Washer
46 8 M4 x 15mm Button Screw
47 1 M5 x 15mm Screw
48 9 M4 x 15mm Screw
49 1 M8 Locknut
50 1 Handlebar
51 2 Pulse Sensor
52 2 Sensor Screw
53 2 Handlebar Foam
54 1 Pivot Clamp
55 1 Pivot Handle
56 1 Seat Knob
57 1 Seat Block
58 1 Seat Carriage
59 2 Pulse Wire
60 2 Snap Ring
61 2 Seat Carriage Cap
62 2 Flange Screw
63 1 Frame Bushing
64 2 M4 x 12mm Screw
65 1 Right Crank Arm
66 1 Left Crank Arm
67 2 Crank Cap
68 1 Lower Wire Harness
*–Userʼs Manual
*–Assembly Tool
Note: Specifications are subject to change without notice. See the back cover of this manual for information
about ordering replacement parts. *These parts are not illustrated.
22
7
15
16
34
42
13
19
17
41
18
35
2
4
30
29
9
31
32
37
38
28
31
32
28
11
1
33
46
22
39
20
5
12
21
24
26
36
34
42
48
8
27
6
14
43
47
41
46
46
4
8
44
43
27
45
25
49
40
10
10
42
42
42
10
50
51
53
54
55
56
57
58
59
61
38
3
48
48
48
51
52
52
48
41
46
46
41
63
64
36
65
67
66
67
62
62
60
23
68
64
61
60
EXPLODED DRAWING—Model No. PFEVEX73108.0 R0908A
23
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
Part No. 269244 R0908A Printed in China © 2008 ICON IP, Inc.
Loading...