ProForm PFEVEX29831 User Manual

Model No. PFEVEX29831
www.iconeurope.com
Visit our website at
Serial No.
Serial
Number
QUESTIONS?
As a manufacturer, we are committed to providing com­plete customer satisfaction. If you have questions, or if there are missing parts, please call:
08457 089 009
USER'S MANUAL
Or write: ICON Health & Fitness, Ltd. Customer Service Department Unit 4 Revie Road Industrial Estate Revie Road Beeston Leeds, LS118JG UK
email: csuk@iconeurope.com
CAUTION
Read all precautions and instruc­tions in this manual before using this equipment. Keep this manual for future reference.
Class HC Fitness Product
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
EFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
B
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
HOW TO OPERATE THE EXERCISE CYCLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
ONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
C
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
IMPORTANT PRECAUTIONS
WARNING:
tions before using the exercise cycle.
1. Read all instructions in this manual before using the exercise cycle.
2. It is the responsibility of the owner to ensure that all users of the exercise cycle are ade­quately informed of all precautions. Use the exercise cycle only as described in this manual.
3. Use the exercise cycle indoors on a level sur­face. Keep the exercise cycle away from moisture and dust. Place a mat under the exercise cycle to protect the floor.
4. Inspect and properly tighten all parts regular­ly. Replace any worn parts immediately.
5. Keep children under the age of 12 and pets away from the exercise cycle at all times.
6. Wear appropriate clothing when exercising; do not wear loose clothing that could become caught on the exercise cycle. Always wear athletic shoes for foot protection.
7. The exercise cycle should not be used by persons weighing more than 115 kg (250 lbs.).
To reduce the risk of serious injury, read the following important precau-
8. Always keep your back straight when using the exercise cycle; do not arch your back.
9. If you feel pain or dizziness whilst exercising, stop immediately and cool down.
10.The exercise cycle does not have a freewheel; the pedals will continue to move until the fly­wheel stops.
11.The pulse sensor is not a medical device. Various factors, including the user's move­ment, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general.
12.The exercise cycle is intended for home use only. Do not use the exercise cycle in a commercial, rental, or institutional setting.
13.A warning decal has been placed on the exer­cise cycle in the location shown on page 3. If the decal is missing, or if it is not legible, please call our Customer Service Department at 08457 089 009 to order a free replacement decal. Apply the decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
2
BEFORE YOU BEGIN
ongratulations for selecting the new PROFORM
C EKG exercise cycle. Cycling is one of the most effec­tive exercises for increasing cardiovascular fitness, building endurance, and toning the entire body. The
ROFORM
P features to let you enjoy this healthful exercise in the convenience and privacy of your home.
For your benefit, read this manual carefully before you use the exercise cycle. If you have questions
after reading this manual, please call our Customer
®
35 EKG offers an impressive array of
7
Fan
Console
Adjustment Handle
®
35
7
ervice Department toll-free at 08457 089 009. To help
S us assist you, please note the product model number and serial number before calling. The model number is PFEVEX29831. The serial number can be found on a
ecal attached to the exercise cycle (see the front
d cover of this manual).
Before reading further, please familiarise yourself with the parts that are labeled in the drawing below.
Handlebar
Pulse Sensor
Seat
Adjustment Knob
REAR
Water Bottle Holder*
Adjustment Knob
Pedal/Strap
Wheel
RIGHT SIDE
*No water bottle is included
3
ASSEMBLY
M10 x 65mm Carriage Bolt (65)–4
M8 Nylon
Locknut (10)–4
M10 Black Nylon
Locknut (63)–4
M8 Split
Washer (64)–4
M8 Washer
(67)–1
M6 x 25.4mm Button
Screw (33)–1
M4 x 16mm
Screw (66)–4
M4 x 22mm
Screw (53)–2
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tools and your own adjustable spanner and Phillips screwdriver .
Use the part drawings below to identify the small parts used in assembly. The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on page 14. The second number refers to the quantity needed for assembly. Note: Some small parts may have been pre-attached for shipping. If a
part is not in the parts bag, check to see if it has been pre-attached.
4
1. Identify the Front Stabiliser (2). Whilst another person lifts the front of the Frame (1) slightly, attach the Front Stabilizer to the Frame with two M10 x 65mm Carriage
olts (65) and two M10 Black Nylon Locknuts (63).
B
Make sure that the Front Stabiliser is turned so the
heels (50) are not touching the floor.
W
2. Whilst another person lifts the back of the Frame (1) slightly, attach a Rear Stabiliser (62) to the Frame with two M10 x 65mm Carriage Bolts (65) and two M10 Black Nylon Locknuts (63).
1
2
65
0
5
63
1
50
2
1
63
63
62
65
3. Whilst another person holds the Upright (13) in the position shown, connect the Upper Wire Harness (36) to the Lower Wire Harness (43).
Turn the indicated Adjustment Knob (28) counterclock­wise two or three turns to loosen it. Next, pull the Knob, insert the Upright (13) into the Frame (1), and then release the Knob. Be careful to avoid pinching the
Wire Harnesses (36, 43). Move the Upright up and down slightly until the pin on the Knob snaps into one of the holes in the Upright. Then, turn the Knob
clockwise until it is tight.
Tighten the M6 x 25.4mm Button Screw (33) into the Frame (1) and into the slot in the side of the Upright (13).
Attach the Water Bottle Holder (6) to the Upright (13) with two M4 x 22mm Screws (53).
4. The Console (16) requires four “D” batteries (not included); alkaline batteries are recommended. Remove the screw from the battery drawer. Pull the battery drawer open and insert four batteries. Make
sure that the batteries are oriented as shown by the markings inside the battery drawer. Close the
battery drawer and reattach the screw. Note: When the batteries are installed correctly, the fan will turn on for a moment.
3
6
13
Slot
36
43
33
4
16
53
1
28
Batteries
Battery
Screw
Drawer
5
. Slide the two slots in the Handlebar Clamp (49) onto the
5
two indicated tabs on the Upright (13). Lift the bottom of
he Handlebar Clamp away from the Upright, and insert
t the Handlebar (15) between the Handlebar Clamp and the Upright. Centre the Handlebar and rotate it to the desired position.
5
15
Slide an M8 Washer (67) onto the Adjustment Handle (9). Insert the Adjustment Handle into the Handlebar Clamp (49), and tighten the Adjustment Handle into the Upright (13). Note: The Adjustment Handle works like a spanner. Turn the Handle clockwise, pull it away from the Upright, turn it counterclockwise, push it toward the upright, and then turn it clockwise again.
6. Hold the Console (16) near the Upright (13). Connect the console wire to the Upper Wire Harness (36). Insert the excess wire into the Upright.
Attach the Console (16) to the Upright (13) with four M4 x 16mm Screws (66). Be careful to avoid pinch-
ing the wires.
13
67
6
16
36
66
66
49
9
Console
Wire
T
abs
7. Turn the indicated Adjustment Knob (28) counterclock­wise two or three turns to loosen it. Next, pull the Knob, insert the Seat Post (5) into the Frame (1), and then release the Knob. Move the Seat Post up and down
slightly until the pin on the Knob snaps into one of the holes in the Seat Post. Then, turn the Knob clock-
wise until it is tight.
13
7
5
1
28
6
8. Attach the Seat (12) to the Seat Post (5) with four M8 Nylon Locknuts (10) and four M8 Split Washers (64). Note: The Nylon Locknuts and the Split Washers may
e pre-attached to the underside of the Seat.
b
8
12
9. Identify the Left Pedal (24), which is marked with an “L.” Using an adjustable wrench, firmly tighten the Left Pedal counterclockwise into the Left Crank Arm (42). Tighten the Right Pedal (not shown) clockwise into the Right Crank Arm. Important: Tighten both
Pedals as firmly as possible. After using the exercise cycle for one week, retighten the Pedals. For best performance, the Pedals must be kept tightened.
Adjust the Left Pedal Strap (25) to the desired posi­tion, and press the end of the Pedal Strap onto the tab on the Left Pedal (24). Adjust the Right Pedal Strap (not shown) in the same way.
64
10
9
25
Tab
24
5
64
10
42
10. Make sure that all parts are properly tightened before you use the exercise cycle. Note: After assembly is
completed, some extra parts may be left over. Place a mat beneath the exercise cycle to protect the floor.
7
HOW TO OPERATE THE EXERCISE CYCLE
OW TO ADJUST THE SEAT POST
H
or effective exer-
F cise, the seat should be at the proper height. As you pedal, there should be a slight bend in your knees when the pedals are in the lowest position. To adjust the height of the seat, first turn the indicated knob counterclockwise two or three turns to loosen it (if the knob is not loosened enough, it may scratch the seat post). Next, pull the knob, slide the seat post to the desired height, and then release the knob. Move the seat post up and down slightly until
the pin on the knob snaps into one of the holes in the seat post. Then, turn the knob clockwise until it is
tight.
HOW TO ADJUST THE HANDLEBAR
The handlebar can be adjusted to the position that is the most comfortable for you. To adjust the handlebar, first turn the adjustment handle counter­clockwise to loosen it. Note: The adjust­ment handle works like a spanner. Turn the handle
Handle
eat
S Post
Seat
Knob
ounterclockwise, pull it away from the handlebar, turn
c it clockwise, push it toward the handlebar, and then
urn it counterclockwise again. Repeat this procedure
t until the handlebar is loose. Move the handlebar up or down to the desired position, and then turn the handle clockwise until it is tight.
HOW TO ADJUST THE UPRIGHT
The upright can be adjusted to the height that is the most comfortable for you. To adjust the upright, first turn the indicated knob counterclockwise two or three turns to loosen it (if the knob is not loosened enough, it may scratch the upright). Next, pull the knob, slide the upright to the desired height, and then release the knob. Move the upright up and down slightly
until the pin on the knob snaps into one of the holes in the upright. Then, turn the knob clockwise
until it is tight.
HOW TO ADJUST THE PEDAL STRAPS
To adjust the pedal straps, see assembly step 9 on page 7.
Upright
Knob
8
HOW TO OPERATE THE CONSOLE
Display Buttons
Fan Button
On/Reset Button
The easy-to-use console offers a selection of features designed to help you get the most from your workouts. Follow the instructions below to operate the console.
Turn on the console.
1
Note: The console requires four 1.5V “D” batteries. See assembly step 4 on page 5 for battery instal­lation instructions.
To turn on the console, press the On/Reset button (see the drawing above to identify the On/Reset button). Note: Moving the pedals is another way to turn on the console.
Begin pedaling and change the resistance of
2
the pedals as desired.
As you pedal, change the resistance of the ped­als by pressing the + and – buttons below the large display. There are ten resistance levels— level 10 is the most challenging. Note: After the buttons are pressed, it will take a few seconds for the resistance to reach the selected setting.
Resistance Buttons
Follow your progress with the small display
3
and the large display.
The small display will
show your pedaling pace, in revolutions per minute (RPM). The indicator bar in the small display will increase or decrease in length as you increase or decrease your pedaling pace. Note: When you use the handgrip pulse sensor, the small display will show your heart rate (see step 4 on page 10).
The upper sec­tion of the large display will
show the dis­tance you have pedaled and the numbers of calories and fat calories you have burned (see FAT BURNING on page 13 for an explanation of fat calories). The display will change from one number to the next every few seconds.
Indicator Bar
9
To view only the distance you have pedaled or the number of calories or fat
alories you have burned,
c press the upper button on
he left side of the large
t display until only the word DISTANCE, CALORIES, or FAT CALS appears in the upper section of the large display; make sure that the word SCAN does not appear. To again view the distance you have pedaled and the numbers of calories and fat calories you have burned, press the upper button until the word SCAN reappears.
The centre of the large dis­play will show
the elapsed time and your current pace (pace is shown in minutes per mile in this section of the large display). The display will change from one number to the other every few seconds.
To view only the elapsed time or your pace, press the centre button on the left side of the large dis­play until only the word TIME or PACE appears; make sure that the word SCAN does not appear. To again view both the elapsed time and your pace, press the centre button until the word SCAN reappears.
The lower sec­tion of the large display will show
your pedaling speed and the resistance level. The display will change from one number to the other every few seconds.
To view only your pedaling speed or the resistance level, press the lower but­ton on the left side of the large display until only the word SPEED or RESIS­TANCE appears; make
Upper Button
Centre Button
Lower Button
sure that the word SCAN does not appear. To again view both your pedaling speed and the resistance level, press the lower button until the
ord SCAN reappears.
w
o reset the displays, press the On/Reset button.
T
Note: The con­sole can show speed and dis­tance in either miles or kilome­ters. The letters
MPH or KM/H will appear in the lower section of the large display to show which unit of measure­ment is selected. To change the unit of measure­ment, hold down the On/Reset button for about six seconds. Note: When the button is held down, the fan will turn on for a moment. When the batteries are replaced, it may be necessary to reselect the desired unit of measurement.
Measure your heart rate if desired.
4
If there are thin sheets of plas­tic on the metal contacts on the handgrips, peel off the plastic.
To use the hand­grip pulse sen­sor, hold the handgrips with your palms resting against the metal contacts. Avoid moving your hands.
When your pulse is detected, the heart­shaped indicator in the small display will flash each time your heart beats. After a moment, two dashes (– –) will appear and then your heart rate will be shown. For the most accurate heart rate reading, continue to hold the handgrips for about 30 seconds.
Metal
Contacts
10
urn on the fan if desired.
T
5
To turn on the fan at low
peed, press
s the fan button. To turn on the fan at high speed, press the fan button a second time. To turn off the fan, press the fan button a third time. Note: If the fan is turned on and the pedals are not moved for about half a minute, the fan will turn off to conserve the batteries.
Fan
utton
B
Thumb
Wheel
Rotate the thumb wheel on the right side of the console to pivot the fan to the desired angle.
When you are finished exercising, the console
6
will automatically turn off.
If the pedals are not moved for a few seconds,
he displays will pause and the time will flash in
t the large display.
If the pedals are not moved and the console but­tons are not pressed for a few minutes, the con­sole will turn off to conserve the batteries.
11
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the exercise cycle reg-
larly. Replace any worn parts immediately.
u
To clean the exercise cycle, use a damp cloth and a small amount of mild detergent. Important: To avoid
amage to the console, keep liquids away from
d the console and keep the console out of direct sunlight.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
• Avoid moving your hands or holding the metal con-
tacts too tightly whilst using the handgrip pulse sen­sor. Excessive movement or pressure may interfere with heart rate readings.
• For the most accurate heart rate reading, hold the
metal contacts for about 15 seconds.
• Keep the metal contacts clean. The contacts can be
cleaned with a soft cloth—never use alcohol, abrasives, or chemicals.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the reed switch should be adjusted. In order to adjust the reed switch, the Left Side Shield (17) must be removed. Remove the seven Screws (52) from the Right Side Shield (18). Next, remove the Screw (59) from the right side of the Side Shield Cover (19).
Using an adjustable wrench, turn the Left Pedal (24)
lockwise and remove it. Next, remove the two
c Screws (66) from the Left Side Shield (17). Remove the Screw (59) from the left side of the Side Shield Cover (19) and lift it off. Gently remove the Left Side
hield.
S
19
59
24
66
Next, locate the Reed Switch (40). Turn the Left Crank Arm (42) until the Magnet (38) is aligned with the Reed Switch. Loosen but do not remove the Screw (66). Slide the Reed Switch slightly closer to or away from the Magnet. Retighten the Screw. Turn the Crank for a moment. Repeat until the console dis­plays correct feedback. When the Reed Switch is cor­rectly adjusted, reattach the left side shield, side shield cover and the pedal.
17
17
52
19
59
18
52
38
40
66
42
BATTERY REPLACEMENT
If the console display becomes dim, the batteries should be replaced; most console problems are the result of low batteries. See assembly step 4 on page 5 for replacement instructions.
12
CONDITIONING GUIDELINES
The following guidelines will help you to plan your exercise program. Remember that proper nutrition and adequate rest are essential for successful results.
WARNING:
• Before beginning this or any exercise pro­gram, consult your physician. This is espe­cially important for persons over the age of 35 or persons with pre-existing health problems.
• The pulse sensor is not a medical device. Various factors may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in deter­mining heart rate trends in general.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your cardiovascular system, the key to achieving the desired results is to exercise with the proper intensity. The proper intensity level can be found by using your heart rate as a guide. The chart below shows recom­mended heart rates for fat burning, maximum fat burning, and cardiovascular (aerobic) exercise.
During the first few minutes of exercise, your body uses easily accessible carbohydrate calories for ener­gy. Only after the first few minutes of exercise does
our body begin to use stored fat calories for energy.
y If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest num­ber in your training zone as you exercise. For maxi­mum fat burning, adjust the intensity of your exercise until your heart rate is near the middle number in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys­tem, your exercise must be “aerobic.” Aerobic exer­cise is activity that requires large amounts of oxygen for prolonged periods of time. This increases the demand on the heart to pump blood to the muscles, and on the lungs to oxygenate the blood. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the highest number in your training zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching and light exercise. A proper warm-up increases your body temperature, heart rate, and circulation in prepa­ration for exercise.
To find the proper heart rate for you, first find your age at the bottom of the chart (ages are rounded off to the nearest ten years). Next, find the three numbers above your age. The three numbers are your “training zone.” The lowest number is the recommended heart rate for fat burning; the middle number is the recommended heart rate for maximum fat burning; the highest num­ber is the recommended heart rate for aerobic exer­cise.
Fat Burning
To burn fat effectively, you must exercise at a relative­ly low intensity level for a sustained period of time.
Training zone exercise, consisting of 20 to 30 min­utes of exercising with your heart rate in your training zone. Note: During the first few weeks of your exer­cise program, do not keep your heart rate in your training zone for longer than 20 minutes.
A cool-down, with 5 to 10 minutes of stretching. This will increase the flexibility of your muscles and will help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three work­outs each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. Remember, the key to success is make exer­cise a regular and enjoyable part of your everyday life.
13
PART LIST—Model No. PFEVEX29831 R
Key No. Qty. Description Key No. Qty. Description
1103A
1 21Front Stabiliser 3 44Stabilizer Endcap 51Seat Post 61Bottle Holder 72Handlebar Endcap 82Foam Grip
91Adjustment Handle 10 5 M8 Nylon Locknut 11 2 Bushing Bracket 12 1 Seat 13 1 Upright 14 1 Upright Bushing 15 1 Handlebar 16 1 Console 17 1 Left Side Shield 18 1 Right Side Shield 19 1 Side Shield Cover 20 1 Seat Post Bushing 21 1 Crank Assembly 22 1 Reed Switch Clamp 23 2 M4 x 5mm Screw 24 1 Left Pedal 25 1 Left Pedal Strap 26 1 Right Pedal 27 1 Right Pedal Strap 28 2 Adjustment Knob 29 4 M6 x 18mm Bolt 30 1 Snap Ring 31 4 M6 x 13mm Button Screw 32 1 Flywheel Washer 33 1 M6 x 25.4mm Button Screw 34 1 Small Pulley 35 4 M6 Nylon Locknut 36 1 Upper Wire Harness 37 1 Flywheel
1 Frame
2 Small Snap Ring
8 1 Magnet
3 39 2 Small Pulley Washer
0 1 Reed Switch/Sensor Wire
4 41 1 “C” Magnet 42 1 Left Crank Arm 43 1 Lower Wire Harness 44 2 Crank Bearing 45 1 Resistance Cable 46 1 Resistance Motor 47 1 Return Spring 48 4 M5 Washer 49 1 Handlebar Clamp 50 2 Wheel 51 2 M10 x 45mm Button Bolt 52 7 M4 x 25mm Screw 53 2 M4 x 22mm Screw 54 1 Pulley 55 1 Belt 56 2 Flange Screw 57 1 Right Crank Arm 58 2 M6 x 8mm Screw 59 2 M4 x 12mm Round Head Screw 60 1 M8 x 35mm Button Screw 61 1 Idler 62 1 Rear Stabilizer 63 6 M10 Black Nylon Locknut 64 4 M8 Split Washer 65 4 M10 x 65mm Carriage Bolt 66 14 M4 x 16mm Screw 67 1 M8 Washer 68 1 Thrust Washer 69 1 2.8mm Spacer 70 1 9mm Spacer 71 1 7.5mm Spacer
#1Userʼs Manual #2Allen Wrench
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.
14
1
62
4
7
13
14
17
1
8
1
9
24
25
42
44
56
63
23
52
66
59
63
63
63
22
66
52
5
2
6
6
66
52
36
12
28
44
15
33
26
27
57
56
20
4
23
65
58
28
58
7
8
55
30
68
38
54
21
29
29
35
35
16
66
6
6
6
49
53
9
65
2
51
50
63
4
4
50
51
63
66
46
48
48
66
40
43
67
5
64
10
64
37
10
41
47
45
3
3
11
11
31
31
31
32
34
39
60
61
69
71
70
EXPLODED DRAWING—Model No. PFEVEX29831 R
1103A
15
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
CON Health & Fitness, Ltd.
I Customer Service Department Unit 4, Revie Road Industrial Estate Revie Road Beeston Leeds, LS118JG UK
Tel:
08457 089 009
Outside the UK: 0 (444) 113 387 7133 Fax: 0 (444) 113 387 7125
To help us assist you, please be prepared to give the following information:
• the MODEL NUMBER of the product (PFEVEX29831)
®
• the NAME of the product (PROFORM
735 EKG exercise cycle)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see page 14 of this manual)
Part No. 203881 R1103A Printed in China © 2003 ICON Health & Fitness, Inc.
Loading...