ProForm PF760034 User Manual

Page 1
®
TRIPLE
ACTION
ELECTROMAGNETIC
SILENT
DRIVE
Model No. PF760034 Serial No. ____________________
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or find there are missing or damaged parts, we will guarantee you complete satisfaction through direct assistance from our factory.
TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The trained tech­nicians on our Customer Hot Line will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.-Fri., 6 a.m.-6 p.m. MST
CAUTION:
Read all safety precautions and instructions in this man­ual carefully before using this equipment. Save this manual for future reference.
PATENT PENDING
OWNER'S MANUAL
Page 2
TABLE OF CONTENTS
IMPORTANT SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTMENT AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLE-SHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back Cover Back Cover
2 3 4
8 11 12 14 15
IMPORTANT SAFETY PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important safety precautions before using the exercise bike.
1. Place the exercise bike on a level surface. Do not use the bike near water or outdoors.
2. Use the exercise bike only as described in this manual.
3. Keep small children away from the exercise bike at all times.
4. Wear appropriate clothing when exercising;
do not wear loose clothing that could become caught in the exercise bike. Always wear athletic shoes for foot protection.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using this product. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
2
5. When connecting the link arms to the pedals (see HANDLEBAR OPERATION on page 8), make sure that the link arms are on the pedal bushings. If the link arms are not on the pedal bushings, they may slip off during use, resulting in injury.
6. When adjusting the seat, at least two inches of the seat post must be inside of the frame. The seat pin must be inserted from the front, as shown on page 3. If the seat pin is inserted from the back, it may slip out during use, resulting in injury.
Page 3
BEFORE YOU BEGIN
Congratulations for selecting the PROFORM®760 exercise bike. Cycling is one of the most effective exercises known for increasing cardiovascular fitness, building endurance and toning the entire body. The sophisticated PROFORM 760 offers an impressive array of features to let you enjoy this healthful exercise in the convenience and privacy of your home.
For your safety and benefit, read this manual carefully before using the exercise bike. If you
have additional questions, please call our Customer
Handlebars
Console
Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please mention the product model number and serial number when calling. The model number is PF760034. The serial number can be found on a decal attached to the exercise bike (see the front cover of this manual).
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
Link Arm
Seat
Seat Post
Seat Pin
Frame
Side Shield
FRONT
LEFT SIDE
BACK
Pedal
3
Page 4
ASSEMBLY
9/16" Washer (56)–2
Pedal Bushing (55)–2
5/16" x 18 Nylon Locknut (17)–2
5/16" x 1 3/4" Bolt (36)–2
3/4" Phillips Screw (4)–4
1/4" Seat Nut (7)–4
5/16" Pedal Nut (49)–2
Link Arm Bushing (58)–2
Pedal Cap (50)–2
Pedal Spring (52)–2
11/16" Spring Washer (51)–2
5/8" Plastic Cap (3)–2
1/2" Nylon Locknut (46)–2
5/16" x 1/2" Screw (33)–2
5/16" x 1 1/4" Bolt (14)–4
11/16" Washer (54)–2
5/16" Washer (65)–2
5/8" Spacer (57)–2
5/8" Handlebar Spacer (76)–2
9/16" Pedal Spacer (75)–2
Place all parts of the exercise bike in a cleared area
nd remove the packing materials. Do not dispose
a of the packing materials until assembly is completed.
Read all steps and examine all drawings carefully before beginning.
Use the part chart below to identify the small parts used in assembly. The number in parenthesis beneath each part refers to the key number of the part. The second number refers to the quantity used
in assembly. Note: Some of the small parts used in
ssembly may have been pre-attached to one of the
a parts to be assembled. If a part is missing, see the back cover of this manual for instructions.
In addition to the tools included, the following tools are required for assembly:
one (1) hammer
one (1) adjustable wrench
4
Page 5
1. Raise the back end of the exercise bike. Attach the Stabilizer (13) to the Frame (11) with the four 5/16" x 1 1/4" Bolts (14). The Stabilizer must be turned so the ribbed sides of the Endcaps (12)
re on the side shown. Lower the exercise bike.
a
1
14
12
13
2
1
1
1
2. Slide the free end of the Roller Axle (42) through the Bushings (43) in the Frame (11). Press the unattached Roller (24) onto the end of the Axle. It may be helpful to tap the Roller with a hammer in order to press it fully onto the Axle.
3. Remove the four 1/4" Seat Nuts (7) from the underside of the Seat (5). Remove the Seat Post (6) from the Frame (11). Attach the Seat to the top of the Seat Post with the four 1/4" Seat Nuts.
Insert the Seat Post (6) into the Frame (11), adjust the Seat (5) to the desired height, and insert the Seat Pin (8) through the front of the Frame and the Seat Post. Slide the Seat Post Collar (30) down over the Frame. CAUTION: At least two inches of the
Seat Post must be inside of the Frame. The Seat Pin must be inserted from the front, as shown. If the Seat Pin is inserted from the back, it may slip out, resulting in injury.
2
24
11
43
42
3
5
7
30
7
8
6
4. Connect the wire protruding from the Console Mount (2) to the
Wire Harness (66) (see the inset drawing). Make sure that the wire is turned so it fits easily into the Wire Harness. If the wire is not turned correctly and is forced into the Wire Harness, the Console (1) will not function properly.
Slide the Console Mount (2) onto the Frame (11). CAUTION: Be
careful to avoid pinching your fingers or the Wire Harness (66). Attach the Console Mount to the Frame with the two 5/16" x
1/2" Screws (33).
11
4
Wire
66
2
66
11
1
33
5
Page 6
5. Plug the Power Cord (70) into the jack at the back of the exercise
ike. Test the console in the following manner:
b
A. Plug the transformer on the Power Cord (70) into a 120-volt
utlet.
o
B. Press the power button on the console (see the drawing at the
top of page 9). The manual mode indicator will light and the LCD display will appear. Next, move the manual resistance
ontrol. You will hear the motor as the resistance changes.
c Next, press the program/manual button. The program mode indicator and the eight segment indicators will light.
If the console does not function as described, see assembly step
4. Make sure that the wire is plugged correctly into the wire harness.
5
70
6. Apply grease (included) to the handlebar shaft of the Frame (11).
Slide a 5/8" Spacer (57) and a 5/8” Handlebar Spacer (76) onto each side of the handlebar shaft. Make sure that the open side
of each 5/8” Spacer is turned toward the Frame.
Slide the Left and Right Neck Shields (67, 68) onto the handlebar shaft of the Frame (11). Insert the four 3/4" Phillips Screws (4) into the Left Neck Shield, and tighten them into the Right Neck Shield.
7. Slide a Handlebar (9) onto the left side of the handlebar shaft of the Frame (11). Tap a 5/8" Plastic Cap (3) onto the handlebar shaft.
Attach the other Handlebar in the same manner (not shown).
6
68
11
76
57
57
7
67
76
4
4
11
3
9
8. Insert a 5/16" x 1 3/4" Bolt (36) through the lower end of the left Handlebar (9). CAUTION: The lower end of the Handlebar may
have a rough edge. Be careful to avoid cutting your fingers.
Tap a Link Arm Bushing (58) into a Link Arm (37). Slide the Link Arm onto the Bolt. The flange of the Link Arm Bushing must be turned toward the Handlebar, and the opening in the end of the Link Arm must be downward as shown. Tighten a 5/16" x 18 Nut (17) onto the Bolt. Do not overtighten the Nut; the Link Arm must pivot freely. Clip the Link Arm onto the lock rod.
Attach the other Link Arm to the right Handlebar in the same manner (not shown).
6
8
36
58
9
Flange
37
Lock Rod
17
Page 7
9. Hold one of the Pedal Shafts (38) with the included tool as shown—the tool must be between the coils of the Pedal Spring (52). Using an adjustable wrench, remove the 1/2" Nylon Locknut (46) from the end of the Pedal Shaft. (There is an 11/16" Spring Washer (51), a Pedal Spring (52), an 11/16" Washer (54), a Pedal Bushing
55), a 9/16" Washer (56) and a 9/16” Pedal Spacer (75) on the Pedal Shaft.) Using the included tool, firmly
( tighten the Pedal Shaft, in a clockwise direction, into one of the arms of the Crank (27). While holding the Pedal
haft with the tool, use an adjustable wrench to tighten the 1/2" Nylon Locknut (46) onto the end of the Pedal
S Shaft. (There is a 5/16" Washer (65) and a 5/16" Pedal Nut (49) on the other end of the Pedal Shaft. The 5/16" Pedal Nut (49) must be flush with the end of the Pedal Shaft.) Press a Pedal Cap (50) into the Pedal (10).
Attach the other Pedal Shaft to the other arm of the Crank in the same manner (not shown).
9
50
49
65
10
51 38
52
Tool
54 55 56
75
27
46
7
Page 8
ADJUSTMENT AND OPERATION
CONNECTING THE POWER CORD
Plug the transformer on the power cord into a 120-volt outlet. Keep the power cord away from walkways and heated surfaces. Turn on the power when using the exercise bike or the bike could be damaged.
SEAT ADJUSTMENT
For effective exercise, the Seat (5) should be adjusted to the proper height. As you pedal, there should be a slight bend in your knees when the pedals are at the lowest position. Dismount the exercise bike. Hold the Seat and remove the Seat Pin (8). Adjust the Seat to the proper height and insert the Seat Pin through the Frame (11) and the Seat Post (6). CAUTION: At least two inches of the Seat
Post must be inside of the Frame. The Seat Pin must be inserted from the front, as shown. If the Seat Pin is inserted from the back, it may slip out during use, resulting in injury.
HANDLEBAR OPERATION
The handlebars can be used in any of three modes: the dual-action mode, for lower- and upper-body exercise; the stationary mode, for lower-body exercise; or the rowing mode, for upper-body exercise.
5
6
8
11
DUAL-ACTION MODE
To use the handlebars in the dual-action mode, the Link Arms (37) must be connected to the pedals. First, lift the Link Arms off the lock rod (see drawing 1). Pull the Link Arms outward against the tops of the 11/16" Washers (54), while pulling against the bottoms of the 11/16" Washers with your fingers (see drawing 2). CAUTION: Be careful to avoid pinching your fingers. Slide the Link Arms onto the Pedal Bushings (55). It may be helpful to move the Link Arms up and down slightly until they slide onto the Pedal Bushings.
CAUTION: Make sure that the Link Arms are on the Pedal Bushings. If the Link Arms are not on the Pedal Bushings, they may slip off during use, resulting in injury.
STATIONARY MODE
To use the handlebars in the stationary mode, the Link Arms (37) must be disconnected from the pedals. Pull the Link Arms outward against the 11/16" Washers (54), until the Link Arms can be lifted off the Pedal Bushings (55) (see drawing 2). CAUTION: Be careful to avoid pinching your fingers. Clip the Link Arms onto the lock rod (see drawing 1).
1
37
Lock Rod
2
54
55
37
ROWING MODE
To use the handlebars in the rowing mode, the Link Arms (37) must be connected to the pedals (see DUAL­ACTION MODE above). Rest your feet on the side shields, and exercise using only your arms.
8
Page 9
DIAGRAM OF THE CONSOLE
5
4
3
2
1
Program Resistance
5
4
3
2
1
35
30
25
20
15
10
5
Program
Time
Manual Resistance
Program / Manual
Power
Display
Mode
Speed Time
S
canCaloriesDistance
Segment Indicators Program Mode Indicator
anual Mode Indicator
M
LCD Display
Mode Indicator
DESCRIPTION OF THE CONSOLE
The heart of the exercise bike is the programmable console. The console offers both manual and program modes, and features a multiple-mode exercise monitor to provide you with instant feedback during your workouts. Remove the clear plastic film from the front of the console. Please read these instructions carefully before operating the console.
TURNING ON THE POWER
To turn on the power, press the power button or simply begin pedaling. The manual mode indicator will light and the LCD display will appear.
MANUAL MODE
When the power is turned on, the console will be in the manual mode. As you pedal, the pedaling resistance can be changed by moving the manual resistance control. To increase the resistance, move the control upward; to decrease the resistance, move the control downward. After the control is moved, it will take a few seconds for the exercise bike to reach the selected resistance setting.
PROGRAM MODE
When the console is in the program mode, the pedaling resistance will be controlled by programs you create. Each program will consist of eight equal time periods, called segments. The resistance will change automatically at the beginning of each segment. To create a program, a resistance setting should be programmed for each of the eight segments by moving
the eight program resistance controls on the left side of the console. The control at far left is for the first segment, and the control at far right is for the eighth segment. To program resistance settings, move the controls to the desired positions. The higher the controls are moved, the higher the resistance settings will be. A sample program is shown above. This program will begin with a low resistance setting. The resistance will then increase during the second and third segments, decrease during the fourth segment, increase again during the fifth and sixth segments, and decrease during the seventh and eighth segments. An infinite variety of settings can be programmed.
Next, move the program time control to set the length of time you want the program to last. The program can be set to last for a minimum of 5 minutes, up to a maximum of 35 minutes.
To start the program, press the program/manual button and begin pedaling. The program mode indicator and the first eight segments will light, and the exercise bike will automatically adjust to the setting of the first program resistance control. After one-eighth of the length of time you set has elapsed, the first segment indicator will darken, and the exercise bike will auto­matically adjust to the setting of the second program resistance control. The program will continue in this manner until all eight segment indicators are dark.
While the program is in progress, the pedaling resis­tance can be changed during the current segment, if desired, by moving the program resistance control for the current segment. If desired, the program can be stopped or the console can be switched to the manual mode by pressing the program/manual button.
9
Page 10
EXERCISE MONITOR MODES
EXERCISE MONITOR OPERATION
The exercise monitor features five different modes:
SPEED—Displays your pedaling speed, in miles per
our.
h
TIME—Displays the elapsed time. Note: Time will be counted only while you are pedaling. If you stop for ten seconds or longer, the TIME mode will hold until you resume pedaling.
DISTANCE—Displays the total distance you have pedaled, in miles.
CALORIE—Displays the total number of Calories you have burned. Note: If the pedaling resistance is near the lowest or highest setting, the actual number of Calories you have burned will be slightly lower or higher than the number displayed.
SCAN—Displays the SPEED, TIME, DISTANCE and CALORIE modes, for five seconds each, in a repeating cycle.
When the power is turned on, the SCAN mode will be
elected automatically. One mode indicator will appear
s by the word "SCAN." The SPEED, TIME, DISTANCE
nd CALORIE modes will be displayed in a repeating
a cycle. A second mode indicator will show which mode is currently displayed.
If desired, the SPEED, TIME, DISTANCE or CALORIE mode can be selected for continuous display by repeatedly pressing the display mode button. The modes will be selected in the following order: SPEED, TIME, DISTANCE, CALORIE, SCAN.
To reset the LCD display, turn the power off and then on again by pressing the power button twice.
TURNING THE POWER OFF
When you are finished exercising, press the power button to turn the power off. Note: If the pedals are not moved and the controls are not used for four minutes, the power will turn off automatically.
10
Page 11
TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts regularly. Outer surfaces of the exercise bike can be cleaned using a damp cloth and
ild, non-abrasive detergent. Keep liquids away from the console.
m
CONSOLE
If the console does not function properly, the wire harness should be checked. See assembly step 4 on page 5. Make sure that the wire harness is plugged fully into the wire extending from the console.
ADJUSTING THE TENSION BELT
If the tension belt slips as you pedal, the tension belt should be tightened. First, disconnect the Link Arms (37) from the Pedals (10) (see STATIONARY MODE on page 8). Next, remove the Pedals (see assembly step 9 on page 7). Remove the four 3/4" Phillips Screws (4) from the Left and Right Neck Shields (67, 68). Remove the #8 x 1" Screws (15) and the 3/4" Tec Screws (69) from the Left and Right Side Shields (16, 34). Slide the Side Shields off the exercise bike. To tighten the tension belt, turn both of the 3/8" Flange Nuts (18) clockwise one full turn. Repeat until the tension belt no longer slips. Reattach the Side Shields, Neck Shields and Pedals.
15
67
4
69
37
69
68
9
34
10
15
16
CENTERING THE TENSION BRACKET
If a grinding noise is heard as you pedal, the Tension Bracket (35) should be adjusted. Disconnect the link arms from the pedals, remove the pedals, and remove the side shields (see ADJUSTING THE TENSION BELT above). Hold the 3/8" x 16 Nylon Locknut (73) with a wrench. If the Tension Bracket is touching the right side of the Resistance Disk (22), turn the Tension Bracket Bolt (60) clockwise until the Tension Bracket is centered. If the Tension Bracket is touching the left side of the Resistance Disk, turn the Bolt counterclockwise. Reattach the side shields, neck shields and pedals.
TIGHTENING THE CRANK ARMS
If the crank arms become loose, they should be tight-ened in order to prevent excessive wear. Loosen the hex nut on the left arm of the Crank (27). Place the end of a standard screwdriver in one of the grooves in the crank nut. Lightly tap the screwdriver with a hammer to turn the crank nut counterclockwise, until the crank arms are no longer loose. Do not overtighten the crank nut. When the crank nut is properly tightened, tighten the hex nut.
18
35
60
left side shield
crank nut
hex nut
22
Top View
73
15
69
35
27
11
Page 12
CONDITIONING GUIDELINES
The following guidelines will help you to plan your exercise program. Remember that proper nutrition and
dequate rest are essential for successful results.
a
WARNING: Before beginning this or any exercise
rogram, consult your physician. This is especially
p important for persons over the age of 35 or persons with pre-existing health problems.
EXERCISE INTENSITY
To maximize the benefits of exercising, it is important to exercise with the proper intensity. The proper intensity level can be found by using your heart rate as a guide. For effective aerobic exercise, your heart rate should be maintained at a level between 70% and 85% of your maximum heart rate as you exercise. This is known as your training zone. You can find your training zone in the table below. Training zones are listed for both unconditioned and conditioned persons according to age.
AGE
UNCONDITIONED
TRAINING ZONE
(BEATS/MIN
CONDITIONED
TRAINING ZONE
(BEATS/MIN
During the first few months of your exercise program, keep your heart rate near the low end of your training
one as you exercise. After a few months, your heart
z rate can be increased gradually until it is near the mid-
le of your training zone as you exercise.
d
To measure your heart rate, stop exercising and place two fingers on your wrist. Take a six-second heartbeat count, and multiply the result by 10 to find your heart rate. For example, if your six-second heartbeat count is 14, your heart rate is 140 beats per minute. (A six-second count is used because your heart rate will drop rapidly when you stop exercising.) Adjust the intensity of your exercise until your heart rate is at the proper level.
20 138-167 133-162
25 136-166 132-160
30 135-164 130-158
35 134-162 129-156
40 132-161 127-155
45 131-159 125-153
50 129-156 124-150
55 127-155 122-149
60 126-153 121-147
65 125-151 119-145
70 123-150 118-144
75 122-147 117-142
80 120-146 115-140
85 118-144 114-139
WORKOUT GUIDELINES
Each workout should consist of three basic parts: a warm-up, 20 to 30 minutes of training zone exercise, and a cool-down. Warming up prepares the body for exercise by increasing circulation, delivering more oxy­gen to the muscles and raising the body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. Then, increase the intensity of your exercise to raise your heart rate to your training zone for 20 to 30 minutes. Breathe regu­larly and deeply as you exercise—never hold your breath. Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the flexibility of the muscles, and reduce soreness and other post­exercise problems. To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. The key to success is to make exercise a regular and enjoyable part of your everyday life.
12
Page 13
SUGGESTED STRETCHES
The following stretches can provide a good warm-up or cool-down. Correct form for each stretch is shown in the drawings below. Move slowly as you stretch—never bounce.
TOE TOUCH STRETCH
Stand with your knees bent slightly and slowly bend forward
rom your hips. Allow your back and shoulders to relax as you
f reach down toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times.
Stretches: Hamstrings, back of knees and back.
HAMSTRING STRETCH
Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. Repeat 3 times for both legs.
Stretches: Hamstrings, lower back and groin.
CALF/ACHILLES STRETCH
With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times for both legs. To cause further stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
QUADRICEPS STRETCH
With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for both legs.
Stretches: Quadriceps and hip muscles.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. Repeat 3 times.
Stretches: Quadriceps and hip muscles.
13
Page 14
PART LIST—Model No. PF760034 R
1294A
Key No. Qty. Description
11Console 21Console Mount 325/8" Plastic Cap 483/4" Phillips Screw 51Seat 61Seat Post 741/4" Seat Nut 81Seat Pin
92Handlebar 10 2 Pedal 11 1 Frame 12 2 Endcap 13 1 Stabilizer 14 4 5/16" x 1 1/4" Bolt 15 12 #8 x 1" Screw 16 1 Left Side Shield 17 2 5/16" x 18 Nut 18 2 1/4” Nylon Locknut 19 1 Small Spacer 20 2 Bearing 21 1 Large Spacer 22 1 Resistance Disk 23 1 Flywheel Axle 24 2 Roller 25 1 Flywheel 26 1 Lock Ring 27 1 Crank 28 1 Tension Belt 29 1 Tension Pulley 30 1 Seat Post Bushing 31 1 Tension Rope 32 4 Handlebar Bushing 33 2 5/16" x 1/2" Screw 34 1 Right Side Shield 35 1 Tension Bracket 36 2 5/16" x 1 3/4" Bolt 37 2 Link Arm 38 2 Pedal Shaft 39 1 Small Spring 40 2 Foam Grip 41 1 Large Spring
Key
No. Qty. Description
42 1 Roller Axle 43 2 Roller Bushing 44 1 #8 x 1/2" Screw 45 1 Seat Post Glide 46 2 1/2" Nylon Locknut 47 1 Crank Hardware 48 2 #4 x 1/2" Screw 49 2 5/16" Pedal Nut 50 2 Pedal Cap 51 2 11/16" Spring Washer 52 2 Pedal Spring 53 1 Tension Motor 54 2 11/16" Washer 55 2 Pedal Bushing 56 2 9/16" Washer 57 2 5/8" Spacer 58 2 Link Arm Bushing 59 2 3/8” Axle Cap 60 1 Tension Bracket Bolt 61 1 Magnet 62 2 3/16" x 1/2" Screw 63 2 5/16" Flange Nut 64 2 Eye Bolt 65 2 5/16" Washer 66 1 Wire Harness 67 1 Left Neck Shield 68 1 Right Neck Shield 69 6 3/4" Tec Screw 70 1 Power Cord 71 1 Reed Switch/Sensor Wire 72 1 3/4" Self-Tapping Screw 73 1 3/8" x 16 Nylon Locknut 74 2 5/16" Flat Washer 75 2 9/16” Pedal Spacer 76 2 Handlebar Spacer
#1Screwdriver/Wrench #1Socket Tool #1Allen Wrench #4M-Clip #1Owner's Manual
Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of this manual for information about ordering replacement parts.
14
Page 15
EXPLODED DRAWING—Model No. PF760034 R
Ro
b
e
r
t
G
o
n
z
a
l
e
s
s
m
e
l
l
s
l
i
k
e
a
b
i
g
h
a
i
r
y
f
r
o
g
.
T
h
i
s
m
e
s
s
a
g
e
i
s
c
o
u
r
t
e
s
y
o
f
V
i
c
t
o
r
W
i
m
m
e
r
.
I
t
h
i
n
k
t
h
a
t
t
h
e
r
e
i
s
a
c
ow
u
p
i
n
m
y
h
e
a
d
.
I
t
h
i
n
k
t
h
a
t
p
e
o
p
l
e
l
o
o
k
f
u
n
n
y
n
a
k
e
d
.
I
s
n
'
t
i
t
s
t
r
a
n
g
e
t
h
a
t
c
o
w
s
h
a
v
e
f
o
u
r
s
t
o
m
a
c
h
s
.
40
3
32
9
10
76
38
37
36
34
15
57
73
39
41
31
35
4
4
66
44
33
2
1
68
5
7
7
6
8
45
67
4
4
4
76
32
32
3
9
40
57
30
48
11
13
14
14
27
28
12
75
60
62
31
24
53
43
42
63
74
64
18
19
26
22
20
28
25
20
21
23
24
72
71
46
61
29
47
70
69
15
16
36
15
9
58
17
15
69
15
38
10
65
49
50
59
37
56
55
54
52
51
69
15
CRANK HARDWARE (47)
1294A
15
Page 16
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
1. The MODEL NUMBER of the product (PF760034).
2. The NAME of the product (PROFORM®760 exercise bike).
3. The SERIAL NUMBER of the product (see the front cover of this manual).
4. The KEY NUMBER and DESCRIPTION of the part(s) from page 10 of this manual.
LIMITED WARRANTY
Icon Health & Fitness, Inc., (“ICON”) warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by a ICON authorized service center or for products used for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PR ODUCT OR OTHER DAM AGES WITH RESPECT TO ANY ECON OMIC LOSS, LOSS OF PROPERTY, LOSS OF REVENUES OR PROFITS, LOSS OF ENJOYMENT OR USE, COSTS OF REMOVAL, INSTALLATION OR OTHER CONSEQUENTIAL DAMAGES OF WHATSOEVER NATURE. SOME STATES DO NOT ALLO W THE EXCLUS ION OR LI MITATION OF INCID ENTAL OR CONSEQUENTIAL DAMAGES. ACCORDINGLY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
THE WARRANTY EXTENDED HEREUNDER IS IN LIEU OF ANY AND ALL OTHER WARRANTIES AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED IN ITS SCOPE AND DURATION TO THE TERMS SET FORTH HEREIN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS. ACCORDINGLY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 122838 R1294A © 1994 Icon Health & Fitness, Inc. Printed in USA
Loading...