
Model No. 831,291710
Serial No,
Serial Number
Decal
F___x E. F_ C I ._, IE_
EQU I PM F--.NT
495 LS
CROSSWALK
USER'S MANUAL
HELPLINEI
1-800-736-6879
SEARS, ROEBUCK AND CO.
HOFFMAN ESTATES, IL 60179
www.proform.com
new products, prizes,
fitness tips, and much morel

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ................................................................. 2
BEFORE YOU BEGIN ....................................................................... 4
ASSEMBLY ............................................................................... 5
OPERATION AND ADJUSTMENT ............................................................. 7
HOW TO FOLD AND MOVE THE TREADMILL .................................................. 10
TROUBLESHOOTING ...................................................................... 12
CONDITIONING GUIDELINES ............................................................... 14
ORDERING REPLACEMENT PARTS .................................................. Back Cover
FULL 90 DAY WARRANTY ........................................................... Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of thismanual. Save the
EXPLODED DRAWING and PART LIST for future reference.
IMPORTANT PRECAUTIONS

Thedecalsshownhavebeenplacedon yourtreadmill.Ifa decal
is missing, or if it is not legible, please call our toll-free
HELPMNE to order a free replacement decal (see the front cover
of this manual). Apply the decal in the location shown.
Note: The decal is shown at 38% of actual size.

BEFORE YOU BEGIN
Congratulations for selecting the new PROFORIvP
CROSSWALK 495 LS treadmill. The CROSSWALK
495 LS treadmill combines advanced technology with
innovative design to help you get the most from your
exercise in the:convenience and privacy of your home.
And when you're not exemising, the unique CROSS-
WALK 495 LS can be folded up, requiringless than haft
the floorspace of other treadmills.
For your benefit, read this manual carefully before
using the b'eadmill. If you have questions after read-
Water Boffie Holder
(Bottle not Included)
Handrail
ing this manual, please call our toll-free HELPLINE at
1-800-736-6879, Monday through Saturday, 7 a.m.
until7 p.m. Central Time (excluding holidays). To help
us assist you, please note the product model number
and serial number before calling. The model number of
the treadmill is 831.291710. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Upper Body Arms
Console
Key/Clip
Storage Latch
Walking Belt
Foot Rail
Rear Roller
Adjustment Bolts
BACK
Updght
RIGHT SIDE
\
Circuit Breaker
Power Cord
Cushioned Walking Platform
for maximum exemise comfort
Incline Leg

ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials untilassembly is completed. Assembly requires the included allen wi_n._
and your own phillips screwdriver _ and wire cutters _.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubdcant with a soft cloth and a mild, non-abrasive cleaner.
<z 0®
Extension Leg Screw/Handrail Screw (53)-4
1. With the help of a second person, carefully raise the
Uprights (11) untilthe treadmill Is In the position shown.
2. Insert one of the Extension Legs (34) into the treadmill
as shown. (Note: It may be helpful to tip the Uprights
[11] in the direction shown by the arrow as you insert
the Extension Leg.) Make sure that the Base Pad (40) is
on the indicated side of the Extension Leg. Attach the
Extension Leg with an Extension Leg Screw (53). Make
sure to push on the head of the Extension Leg
Screw while tightening it.
Small Screw (13)-2
Console Screw (99)-6
Attach the other Extension Leg (34) in the same way.
53

3. Remove the Handrail Screw (53) from one of the
Handrails (1). Insert the Handrail into the tube at the top
of the left Updght (11), and align the hole in the Handrail
with the slotted hole in the Updght. Loosely thread the
Handrail Screw into the Handrail, rotate the Handrail until
the Screw is touching one end of the slotted hole, and
then fully tighten the Screw.
Attach the other Handrail (1) to the right Upright (11) in
the same way.
4. Place the Console Base (46) on the tubes on the Updghts
(11). Pull out just enough of the two Wires (21) to connect
them to the oonnectom in the Console Base. Make a loop
with the indicated plastic tie amud the Wires and insert
the end through the tie holder on the bottomof the
Console Base. Plug the Wire that has a red connector
into the corresponding connector In the Console Base.
The connectors should fit together without being
forced; if they do not, rotate the connector on the
Wire and then plug it In. Next, plugthe other Wire Into
the other connector In the Console Base. Important:
Make sure that both Wires are fully inserted.
WARNING: Do not disconnect or connect the Wires
while the treadmill power cord is plugged in. Pull the
plastic tie tight and cut off the end.
3
53
Refer to drawing 4b. Thread six Console Screws (99) into
the Uprights (11) and the Console Base (46). After all six
Console Screws have been started, tighten the Screws
until they are snug; do not overtighten the Screws.
5. Attach the Storage Latch (14) to the left Updght (11) with
two Smafl Screws (13). Be careful not to overtlghten
the Latch Screws.
6. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the
floor or carpet, place a mat under the treadmill.
99
14/_
_;:>-13
99

OPERATION AND ADJUSTMENT
THE PERFORMANT LUBE TM WALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBE TM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home's power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the pos-
sibility of your treadmill being damaged, always
use a surge suppressor with your treadmill (see
drawing I at the right). To purchase a surge sup-
pressor, see your local SEARS or call ton-free 1-
800-366-7278 and order part number 146148.
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an approprlata
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCl-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustratedin drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
/_-I_Grounded Outlet Box
_'-1 j_ surge Suppressor
II I'$11I:1,3 Grounding Pin
Grounded Outlet G'roundingPlug_'_
2
Grounded Outlet Box
_]y _Ada .SurgeSuppressor
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it Is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock.This product is equipped with a cord having
Metal Screw
The temporary adapter should be used only until a
propedy grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored dgid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used if must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.

CONSOLE DIAGRAM
_O_Vl
V'SUi"/'O_
se_,n-_v
A WARN|
r_dmq
_bbob_mt
_mdm_
KJep_ m
POWER INCLINE ONI REEET
©
Note: If there is a thin sheet of clear
plastic on the console, remove it.
Key
BaRedes
SPEEDCONTROL
SPEEDTRAININGZONES
Tab
BATrERY INSTALLATION
The console requires two or three "AA" batteries
(not included). Alkaline batteries are recommended.
Open the battery cover as shown in the drawing at the
upper right. Insert the batteries into the battery com-
partment, making sure that the negative (-) ends of the
batteries are touching the springsin the battery com-
partment.
Close the battery cover, push up on the battery cover
tab, and then push the tab forward as shown in the
Inset drawing. Make sure that the tab locks Into place.
STEP-BY-STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is propedy plugged in (see page 7).
Stand on the foot rails of the treadmill. Find the clip at-
tached to the key (see the drawing at the top ofthis
page), and slide the clip onto the waistband of your
clothes. Next, insert the key into the console. Test the
clip by carefully taking a few steps backward until
the key is pulled from the console. If the key is not
pulled from the console, adjust the position of the
clip as needed.
8

Follow the steps below to operate the console.
D Insert the key fully Into the power switch.
Inserting the key will
not turn on the dis-
plays. The displays will
turn on when the
ON/RESET button is
pressed or when the
walking belt is started.
Note: If you just
installed batteries, the displays will already be on.
B Reset the speed control and start the walking
belt.
Slide the speed controlfully to the left to the reset
position. Note: Each time the walking belt is
stopped, the speed control must be moved to
the reset posltton before the walking belt can
be restarted.
D Monitor your progress with the two displays.
TIME/DISTANCE dis-
play--This display
Arrow
shows the elapsed time
and the distance that
you have walked or run,
_ME D_TANCE
in miles. Every few sec-
onds, the display will
change from one number to the other, as shown
by the arrows in the display.
CALS/FAT CALS/
SPEED display--This
Arrow
display shows the ap-
proximate numbers of
calories and fat calories
CAL_. FATCALS, SPEED
you have burned. (See
FAT BURNING on page
14.) In addition, the display shows the speed of
the walking belt, in miles per hour. Every few sec-
onds, the display will change from one number to
the next, as shown by the arrows in the display.
SPEED CONTROL
'._M-UP FATBURN AEROBIC PER¥OR_,CE
_PEEO TRAINING ZONES _
SLOW
f
Next, slowlyslide the speed control to the dght
untilthe walking belt begins to move at slow
speed. Carefully step onto the walking belt and
begin exercising. Change the speed of the walldng
belt as desired by slidingthe speed control.
To stop the walldng belt, step onto the foot rails
and slide the speed control to the reset position.
Note: During the first few minutes that the treadmill
is used, inspectthe alignment of the walking belt
and align it if necessary (see page 13).
B Adjust the incline of the treadmill as desired.
To change the in-
cline of the treadmill,
press the increase
or decrease button
until the desired in-
cline level is
reached.
To reset the displays at
any time, press the
ON/RESET button.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To change
the unit of measurement, hold down the
ON/RESET button for five seconds.
B When you are finished exercising, stop the
walldng belt and remove the key.
Step onto the foot rails, slide the speed control to
the reset position, and remove the key from the
console. The displays will tum off a few minutes
after the key is removed. Note: Any time that the
walking belt is stopped and the ON/RESET
button is not pressed for a few minutes, the
displays will automatically turn off to conserve
the batteries.
9

HOW TO USE THE UPPER BODY ARMS
As you exemise on the treadmill, you can hold either the
handrails or the upper body arms. The upper body arms are
designed to exercise your arms, shoulders, and back for a
total body workout. Hold one upper body arm with each
hand, and move them forward and back as you walk on the
treadmill.
To vary the intensity of your upper body exemise, the resis-
tance of the upper body arms can be adjusted. To increase
the resistance, tum the resistance knobs clockwise; to de-
crease the resistance, turn the knobs counterclockwise.
Upper Body
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands In the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the trsadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Press out on the storage latch. Raise the
treadmill until the storage latch closes over the catch.
Make sure that the storage latch is fully closed over
the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.

HOWTOMOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described on page 10. Make sure that the
storage latch is fully closed over the catch.
1. Hold the upper ends ofthe handrails. Place one foot on
the base as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. To reduce the risk of injury, usa extreme caution
while moving the treadmill. Do not move the treadmill
over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left thumb, press the storage latch
and hold it. Pivot the treadmill until the frame and foot rail
are past the storage latch.
Front Wheels
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame to
the floor. To decrease the possibility of Injury, bend
your legs and keep your back straight.
11

TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Red the symptom that
applies, and follow the steps listed. If further assistance Is needed, call our toll-free HELPUNE at
1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged Into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor
that meets all of the specifications describedon page 7. Important: The treadmill Is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted intothe console.
frame near the power cord. ff the switch protrudes c
as shown, the cimult breaker has tdpped. To reset Tdpped
the cimuit breaker, wait for five minutes and then
c. Check the circuit breaker located on the treadmill J=
press the switch back in.
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not ran, please call our toll-free HELPLINE.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the bettedes in the console. If the batteries need to be replaced, see BATTERY
INSTALLATION on page 8. Most problems are the result of drained batteries.
b. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the Resistance Knob (98)
from the left Upright. RemOve the screws from the
hood, and carefully remove the hood.
b
Reset
Locate the Reed Switch (86) and the Magnet (87) on
the left side of the Pulley (85). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8". If necessary, loosen the Screw
(82) and move the Reed Switch slightly.Retighten the
Screw. Re-attach the hood, and run the treadmill for a
few minutes to check for a correct speed reading.
Reattach the Resistance Knob.
Top
View

PROBLEM:Thewalkingbeltslowswhenwalkedon
SOLUTION:a. Useonlya single-outletsurgesuppressorthatmeatsallofthespecificationsdescribedonpage7.
b. Ifthewalldngbeltisovertightened,treadmillperfor-
maneamaydecreaseandthewalkingbeltmaybe-
comedamaged.RemovethekeyandUNPLUGTHE
POWERCORD.Usingtheallenwrench,turnboth
rearrolleradjustmentboltscounterclockwise,1/4ofa
turn.Whenthewalkingbeltispropedytightened,you
shouldbeabletolifteachsideofthewalkingbelt2 to
3Inchesoffthewalkingplatform.Becarefulto keep
thewalkingbeltcentered.Pluginthepowercord,in-
sertthekeyandrunthetreadmillfor a few minutes.
Repeat until the walking belt is properlytightened.
c. If the walking belt still slows when walked on, please call our toll-free HELPLINE.
PROBLEM: The walking belt Is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, firstremove the key
and UNPLUG THE POWER CORD. If the welMng
belt has shifted to the left, use the allen wrench to
turn the left rear rollerbolt clockwise1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt countemiockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug inthe power cord;
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b
Rear Roller Adjustment Bolts
a
b. If the walkingbelt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctlytight-
ened, you shouldbe able to lifteach side of the walk-
ing belt 2 to 3 inches off the walking platform. Be
careful to keep the walldng belt cantered. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat untilthe walking
belt is properlytightened.
PROBLEM: ONE OF THE UPPER BODY ARMS SQUEAKS DURING USE
SOLUTION: a. Correcting this problem requires a small amount of
white marine grease, available at most hardware
stores. Turn the Resistance Knob (98) counterclock-
wise untilit can be removed. Remove the Resistance
Cone (93) and the Upper Body Arm (89), along with
the 3/8" Washers (57), Spring Washer (95), Thrust
Washers (96), and Thrust Bearing (97). (Note: If the
Resistance Sleeve [92] comes out of the Resistance
Bracket [91], press it back in.) Apply a thin layer of
white marine grease to the outer surface of the
Resistance Cone (93). Reattaeh all parts in the order
shown at the right.
91
92
13

CONDITIONING GUIDELINES
The following guidelines will help you to plan your ex-
emise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to bum fat or to strengthen your
cardiovascular system, the key to achieving the de-
sired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chad below shows recom-
mended heart rates for fat burning and aerobic exer-
cise.
HEART RATE TRAINING ZONE
= r_ ...... ..
training zone. It may also be helpful to set the speed
control on the console to FAT BURN to help you main-
tain the proper intensitylevel. (See page 9.)
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be "aerobic." Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged pedods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill untilyour
heart rate is near the highest number in your training
zone. It may also be helpful to set the speed control on
the console to AEROBIC to help you melnteln the
proper intensity level. (See page 9.)
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning,
set the speed control on the console to PERFOR-
MANCE to help you maintain the proper intensity level.
(See page 9.) Note: During the first few weeks of yo_Jr
exercise program, keep your heart rate near the low
end of your training zone.
HOW TO MEASURE YOUR HEART RATE
C70
80 =_ _ r •
(, 80 r•
To find the proper heart rate for you, first find your age
on the left side of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers to
the right of your age. The three numbers are your
"training zone." The lower two numbers are recom-
mended heart rates for fat burning; the higher number
is the recommended heart rate for aerobic exercise.
Fat Burning
To bum fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to bum fat,
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
To measure your
heart rate, stop exer-
cising and place two
fingers on your wdst
as shown. Take a
six-second heartbeat
count, and multiply
the result by ten to
find your heart rate.
(A six-second count is used because your heart rate
drops quickly when you stop exercising.) If your heart
rate is too high or too low, adjust the speed or incline
of the treadmill accordingly.
WORKOUT GUIDELINES
A well-rounded workout includes the following three
important pads:
A Warm-up
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.

Training Zone Exercise
After warming up, increase the intensity of yourexer-
cise untilyour pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exer-
cise program, do not keep your pulse in your training
zone for longer than 20 minutes.) Breathe regularly
and deeply as you exercise--never hold your breath.
A Cool-down
Finish each workout with 5 to 10 minutes of stretching
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch--never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees, end
back.
to cool down. This will increase the flexibility of your
muscles and will help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
twean workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
2
2. Hamstring Stretch
Sit with one leg extended. Bringthe sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstdngs,
lower back, and groin.
3. Calf/Achilles Stretch
With one leg in front ofthe other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
footfiat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons, and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times
for both legs. Stretches: Quadriceps and hip muscles.
4
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quaddceps and
hip muscles.
15

REMOVE THIS EXPLODED DRAWING AND PART
LIST FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference,
Note: Specifications are subject to change without notice. For information about
ordering replacement pans, see the back cover of the User's Manual.

PART LISTmModel No. 831.291710 ROSO2A
Key No, Qty.
1 2 Handrail
2 1 Key/Clip
3 2 Incline Leg Pivot Bolt
4 1 Battery Cover
5 2 Foot Rail
6 1 Lift Motor
7 1 Rear Roller
8 1 Speed Potentiometer
9 1 Speed Control Knob
10* 1 Console Assembly
11 1 Upright Base
12 1 Motor Belt
13 4 Small Screw
14 1 Storage Latch
15 2 Frame Pivot Spacer
16 7 8" Cable Tie
17 3 Motor Nut
18 1 PuUey/Flywheel/pan
19 1 Motor
20* 1 Motor/Pulley/Flywheel/Fan
21 1 Wire Harness
22 4 Belt Guide Screw
23 1 Motor Hood
24 1 Hood Shield
25 12 Screw
26 1 Controller
27 1 Motor Swivel Bolt
28 1 Motor Tension Nut
29 5 Small Star Washer
30 1 Motor Tension Washer
31 2 Motor Tension Bolt
32 1 Incline Stop Bracket
33 9 Belly Pan/Clip/Handrail Screw
34 2 Extension Leg
35 4 Endcap Screw
36 2 Wheel Bolt
37 2 Wheel
38 6 Wheel Nut/Lift Nut
39 9 Washer
40 4 Base Pad
41 2 Handrail Cap
42 1 Latch Catch
43 1 Reed Switch Clip
44 1 Reed Switch
45 1 Magnet
46 1 Console Base
47 2 Front Isolator
48 4 Platform Screw
49 2 Isolator
50 1 Front Roller/Pulley
51 1 Front Roller Adj. Bolt
52 2 Incline Wheel
53 4 Extension Leg Screw/Handrail
54 1 Power Cord
Description
Screw
Key No. Qty. Description
55 1
56 1
57 6
58 2
59 1
60 1
61 2
62 2
63 3
64 1
65 2
66 4
67 1
68 I
69 1
7O 8
71 1
72 1
73 5
74 1
75 1
76 2
77 2
78 4
79 4
8O 1
81 2
82 1
83 2
84 1
85* 2
86 1
87 2
88 2
89 1
90 2
91 2
92 2
93 2
94 1
95 2
96 4
97 2
98 2
99 6
100 1
101 1
102 4
# 1
# 1
# 1
# 1
* Includes all parts shown in the box
# These parts are not illustrated
Power Cord Grommet
Circuit Breaker
3/8" Washer
Frame Pivot Bolt
Latch Decal
Motor Belly Pan
Cable Tie Clamp
Rear Platform Screw
Releasable Tie
Choke
Belt Guide
Belly Pan Fastener
Walking Belt
Walking Platform
Belly Pan
Electronics Screw
Incline Wire Harness
Upright Grommet
Isolator Screw
Allen Wrench
Frame
Front Endcap
Incline Wheel Bolt
Resistance Bracket Bolt
Incline Wheel Nut
Ground Wire
Hood Screw (Front)
Incline Leg
Rear Roller Adj. Bolt
Rear Endcap
Extension Leg Assembly
Incline Motor Bolt
Belly Pan Screw
Foam Gdp
Left Upper Body Arm w/Foam Grip
Resistance Bolt
Resistance Bracket
Resistance Sleeve
Resistance Cone
Right Upper Body Arm w/Foam Grip
Spring Washer
Thrust Washer
Thrust Bearing
Resistance Knob
Console Scraw/Latch Screw
Motor Belt Shield
Book Rack
Star Washer
4" Red Wire, M/F
14" White Wire, Pigtail
4" Blue Wire, M/F
User's Manual

EXPLODED DRAWING--Model No. 831.291710
9
i 46 101
R0502A
2
85*
36
34
48
51
53
11
13
20*
I
i
17
i
i
I
I
J
I
,,,.,._o
53-'-_,
r o
21
99
23
24
\
""'-.. 54
"'-.. 56
a
25
7"
86
31
83 _._° _73 79-------_..
">_"'%39 ,;->_8o _9--_
25
5
68
-.. 47 -J
i
I
62
/
59
82
52
77
'' 65
22 64
53 j-
r
,-'!,
36 25
57
i
!
I
i
I
I
i
I
i
I
i
I
i
I
i
33
i
33
i

SEARS
Model No. 831.291710
QUESTIONS?
If you find that:
• you need help assembling or
operating the PROFORM
CROSSWALK 495 LS treadmill
• a part is missing
• or you need to schedule repair
service
call our toll-free HELPLINE
1-800-736-6879
Monday-Saturday, 7 am-7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
The model number and serial number of your PROFORM"
CROSSWALK 495 LS treadmill are listed on a decal attached to
the frame. See the front cover of this manual to find the location of
the decal.
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
When requesting help or service, or ordering pads, please be
prepared to provide the following information:
• The NAME OF THE PRODUCT (PROFORM ° CROSSWALK 495
LS treadmill)
• The MODEL NUMBER OF THE PRODUCT (831.291710)
• The KEY NUMBER AND DESCRIPTION OF THE PART (see the
EXPLODED DRAWING and PART LIST in the center of this
manual)
If parts become wom and need
to be replaced, call the following
toll-free number
1-800-FON-PART
(1-800-366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship inthis
SEARS TREADMILL EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the TREADMILL EXERCISER, free of charge.
This warranty does not apply when the TREADMILL EXERCISER is used commercially orfor rental pur-
poses.
This warranty gives you specific legal rights, and you may also have other rightswhich vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 183475 R0502A Printed in USA © 2002 Sears, Roebuck and Co.