ProForm PFEL099070, Club Design 1000 Owner's Manual
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
Model No. PFEL09907.0
Serial No. _
Write the serial number in the
space above for reference.
Serial Number
Decal
(beneath
ramp)
USER’S MANUAL
QUESTIONS?
As a manufacturer, we are committed to providing complete customer
satisfaction. If you have questions,
or if parts are damaged or missing,
PLEASE DO NOT CONTACT THE
STORE; please contact Customer
Care.
IMPORTANT: You must note the
product model number and serial
number (see the drawing above)
before contacting us:
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
www.proformservice.com
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
2
PROFORM is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
The warning decals shown here have
been applied in the locations shown.
If a decal is missing or illegible,
call the telephone number on the
front cover of this manual and
request a free replacement decal.
Apply the decal in the location
shown. Note: The decal may not be
shown at actual size.
3
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional setting.
4. Keep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 300 lbs.
(136 kg).
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exerciser. Always wear athletic shoes for foot
protection.
9. Hold the handgrip pulse sensor or the handlebars when mounting, dismounting, or
using your elliptical exerciser.
10. Keep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the user’s movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
14. Use your elliptical exerciser only as
described in this manual.
15. Always unplug the power cord immediately
after use and before cleaning the elliptical
exerciser.
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS
4
BEFORE YOU BEGIN
Congratulations for selecting the new PROFORM
®
CLUB DESIGN 1000 elliptical exerciser. The CLUB
DESIGN 1000 elliptical exerciser is an incredibly
smooth exerciser that moves your feet in a natural
elliptical path, minimizing the impact on your knees
and ankles.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before contacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Left Handlebar
Handgrip Pulse Sensor
Power Socket
Wheel
Pedal
Fan
Console
Ramp
Left Upright
Foot
Pedal Arm
Accessory Tray
5
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included tools, assembly requires a Phillips screwdriver , two adjustable
wrenches , a rubber mallet , and pliers .
Use the drawings below to identify the small parts required for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: Some small parts may have been pre-
assembled. If a part is not in the hardware kit, check to see if it has been preassembled.
M8 Split
Washer
(101)–12
M8 Nylon
Locknut (102)–12
M8 x 56mm Button Screw (108)–4
M8 x 23mm Flat
Head Screw (88)–6
M8 Washer
(94)–6
M4 x 25mm
Screw (105)–4
Wave Washer
(100)–2
M8 x 76mm Button Bolt (112)–4
M8 x 25mm
Washer (95)–2
M8 x 20mm Button
Screw (113)–2
M8 x 68mm Button Screw (110)–8
M8 x 28mm
Washer (99)–4
M8 x 25mm Button
Screw (81)–2
6
1.
Remove the Pivot Arms (not shown) and the plastic
inserts from the Left and Right Uprights (4, 3).
Identify the Left Upright (4) and hold it near the Frame
(1). Connect the Extension Wire Harness (76) to the
Lower Wire Harness (77). While another person lifts
the left side of the Frame, pull up on the Extension
Wire Harness and insert the Left Upright into the
Frame. Attach the Left Upright with two M8 x 56mm
Button Screws (108), two M8 x 68mm Button Screws
(110), and four M8 Split Washers (101); be careful to
avoid pinching the Wire Harnesses.
Tighten a Frame Cushion (32) into the left side of the
Frame (1) in the indicated location.
While the other person lifts the right side of the Frame
(1), attach the Right Upright (3) in the same way.
Note: There are no wire harnesses on the right side.
Tighten the other Frame Cushion (32) into the right
side of the Frame (1).
1
4
1
108
Pull
101
101
Do not pinch the
wire harnesses
during this step
32
32
3
110
Plastic
Insert
76
77
6
3
4
2. While another person holds the Console Frame (6)
near the Uprights (3, 4), connect the Upper Wire
Harness (75) to the Extension Wire Harness (76).
Push the excess Wire Harness down into the left
Upright. Next, attach the Console Frame to the
Uprights with four M8 x 76mm Button Bolts (112) and
four M8 Nylon Locknuts (102); be careful to avoid
pinching the Wire Harnesses as you slide the
Console Frame onto the Uprights and insert the
Button Bolts.
2
112
112
102
76
75
Do not pinch the
wire harnesses
during this step
To make assembly easier, read the information
on page 5 before you begin assembling the
elliptical exerciser.
7
3
3. Slide an M8 x 28mm Washer (99) onto an M8 x 20mm
Button Screw (113). Tighten the Button Screw into one
end of the Incline Axle (40). Apply a small amount of
the included grease to the Incline Axle.
Orient the Ramp (5) so that the straight end is in the
position shown. Hold the welded tube on the bottom of
the Ramp between the two rings on the top of the
Frame. Insert the Incline Axle (40) through the rings
and the welded tube.
Slide an M8 x 28mm Washer (99) onto an M8 x 20mm
Button Screw (113). Tighten the Button Screw into the
open end of the Incline Axle (40).
Be careful not to scratch the Ramp (5) during steps
4 through 6.
113
5
99
113
4. Using your fingers, turn the shaft on top of the Lift
Motor (42) counterclockwise until it stops turning.
Position the U-bracket on the bottom of the Ramp (5)
over the end of the shaft as shown. Next, hold an
Incline Motor Spacer (60) on each side of the shaft,
between the shaft and the U-bracket.
Next, insert the Short Clevis Pin (118) through the Ubracket on the Ramp (5), the shaft on the Lift Motor
(42), and the two Incline Motor Spacers (60). Insert
the straight end of a Hairpin (71) into the end of the
Short Clevis Pin.
118
60
42
Front View
5
71
4
40
99
Grease
1
Straight
End
5. See the inset drawing. While another person tips the
elliptical exerciser as shown, place a sturdy piece of
packaging foam beneath the elliptical exerciser. Have
the other person continue to hold the elliptical
exerciser to steady it during this step.
Orient the Rear Stabilizer (2) so that the holes are
closer to the front. Attach the Rear Stabilizer to the
rear of the Frame (1) with four M8 x 68mm Button
Screws (110) and four M8 Split Washers (101).
Carefully remove the piece of packaging foam and tip
the elliptical exerciser back down.
5
1
110
110
101
2
8
95
15
11
121
88
14
13
12
7. Identify the Left Pedal (14). Attach the Left Pedal to
the Left Pedal Arm (12) with three M8 x 23mm Flat
Head Screws (88), three M8 Washers (94), and three
M8 Nylon Locknuts (102). Then, press the Left Pedal
Insert (121) onto the Left Pedal.
Attach the Right Pedal (13) to the Right Pedal Arm (not
shown), and press the Right Pedal Insert (122) into the
Right Pedal, in the same way.
6
7
6. Apply a small amount of grease to the axle on each
Pivot Shaft (15).
Hold a Pedal Wheel (35) inside of the bracket on the
end of the Right Pedal Arm (11). Next, insert a Pivot
Shaft (15) through the holes in the end of the Right
Pedal Arm and the Pedal Wheel as indicated. Tighten
an M8 Nylon Locknut (102) with an M8 x 25mm
Washer (95) onto the end of the Pivot Shaft.
Attach the other Pivot Shaft (15) and the other Pedal
Wheel (35) to the Left Pedal Arm (12) in the same
way.
35
35
102
12
15
88
102
94
Grease
122
9
10. Make sure that all parts of the elliptical exerciser are properly tightened. Cover the floor beneath the
elliptical exerciser to protect the floor from damage. Note: Some extra hardware may be left over.
8. Apply a thin film of the included high-temperature
lubricant to both Pivot Shafts (15).
Identify the Right Handlebar (9), which is marked with
a sticker. Apply a small amount of grease to the axle
on the Right Handlebar, to the Pivot Arm Cover (64),
and to the Inner Upright Cover (63).
Next, slide the Right Handlebar (9) onto the right Pivot
Shaft (15), and insert the axle on the Right Handlebar
into the Right Upright (3). Note: Position the Right
Pedal (13) near the top of the Ramp (5), and lift
and push the Right Pedal sideways, toward the
center of the Ramp, to insert the axle into the
Right Upright.
Next, slide a Wave Washer (100) onto the end of the
axle on the Right Handlebar (9). Apply a small amount
of grease to an M8 x 28mm Washer (99), slide the
Washer onto an M8 x 25mm Button Screw (81), and
tighten the Button Screw into the axle. Then, attach an
Outer Upright Cover (74) to the Right Upright (3) with
two M4 x 25mm Screws (105).
Attach the Left Handlebar (10) to the left Pivot Shaft
(15) and the Left Upright (4) in the same way.
9
15
Lubricate
3
13
74
100
99
9. Plug the Power Cord (8) into the Power Receptacle
(68) at the rear of the elliptical exerciser.
Next, plug the Power Cord (8) into an appropriate
outlet as described on page 10, and calibrate the
elliptical exerciser’s incline system by following
the steps on page 22.
8
68
9
8
63
64
81
105
10
5
4
Grease
15
Lubricate
Axle
Loading...