ProForm C800, 831.150330 User Manual

CAUTION
Read all precautions and instruc­tions in this manual before using this equipment. Save this manu­al for future reference.
WEIGHT BENCH EXERCISER
User ’s Manual
Patent Pending
Write the serial number in the space above for reference.
Serial Number Decal (under seat)
Sears, Roebuck and Co., Hoffman Estates, IL 60179
• Assembly
• Adjustments
• Part List and Drawing
2
WARNING DECAL PLACEMENT
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
FULL 90-DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: APART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING is attached in the center of this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin­ning assembly.
TABLE OF CONTENTS
The warning decals shown here have been placed on the weight bench in the locations shown. If a decal is missing or illegible, please call toll-free 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time, to order a free replacement decal. Place the decal on the weight bench in the location shown.
!
WARNING
To prevent the risk of the rack tipping or sliding, which may cause injury, mount this bracket onto the rack base before performing press exercises.
1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual.
2. It is the responsibility of the owner to ensure that all users of the weight bench are ade­quately informed of all precautions.
3. The weight bench is intended for home use only. Do not use the weight bench in any commercial, rental, or institutional setting.
4. Use the weight bench only on a level surface. Cover the floor beneath the weight bench to protect the floor.
5. Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately.
6. Keep children under 12 and pets away from the weight bench at all times.
7. Keep hands and feet away from moving parts.
8. Always wear athletic shoes for foot protec­tion while exercising.
9. Use the curl bar only with the weight clips provided with the bench.
10. Always set both barbell guides and both safety spotters at the same height.
11. Make sure that the set screws attaching the Olympic weight adapters are properly tight­ened each time the adapters are used.
12. The weight bench is designed to support a maximum user weight of 300 pounds and a maximum total weight of 610 pounds. Do not place more than 310 pounds on the barbell or safety spotters. Do not place more than 150 pounds on the leg lever or curl bar. Note: The weight bench does not include weights.
13. Always place an equal amount of weight on each side of the barbell.
14. Always secure the weights with the weight clips when they are mounted on the barbell.
15. Always make sure the backrest bracket is fully engaged before using the backrest.
16. Always mount the “L”-bracket onto the cen­ter base before performing press exercises.
17. Always move your bench out of the way when performing an exercise that does not use the bench.
18. If you feel pain or dizziness at any time while exercising, stop immediately and begin cool­ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. Sears assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
IMPORTANT PRECAUTIONS
3
4
BEFORE YOU BEGIN
ASSEMBLED DIMENSIONS: Height: 75 in. Width: 84 in. Length: 30 in.
Safety Spotter
Curl Pad
Locking Bar
Guide Bar
Leg Lever
Seat
Barbell
Curl Bar
Backrest
Thank you for selecting the versatile PROFORM
®
C800 weight bench. The weight bench offers an impressive array of weight stations designed to devel­op every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular sys­tem, the weight bench will help you to achieve the specific results you want.
For your benefit, read this manual carefully before using the weight bench. If you have questions after
reading this manual, call 1-800-4-MY-HOME
®
(1-800-469-4663). To help us assist you, please note the product model number and serial number before calling. The model number is 831.150330. The serial number can be found on a decal attached to the weight bench (see the front cover of this manual for the location of the decal).
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled.
Upright
Right Side
Left Side
Note: The “right side” and the “left side” are determined relative to a person sitting on the bench; they do not correspond to right and left on the drawings in the manual.
5
1.
Press a Notched Square Inner Cap (18) into the end of the Bench Frame (1). Attach a Base Cap (9) to the Stabilizer (2) with an M4 x 16mm Screw (58) and an M10 x 25mm Button Screw (78).
Attach another Base Cap to the Stabilizer in the same manner.
Attach the Stabilizer (2) and the “L”-bracket (76) to the Bench Frame (1) with two M10 x 95mm Carriage Bolts (61) and two M10 Nylon Locknuts (69). Secure the Stabilizer to the Bench Frame with two M10 x 68mm Button Bolts (79), two M10 Washers (67), and two M10 Nylon Locknuts. Do
not tighten the Locknuts yet.
2. Press a Thin Notched Square Inner Cap (86) into the bottom of the Bench Leg (3). Attach the Small Base Cap (80) to the Bench Leg with an M4 x 16mm Screw (58).
Attach the Bench Leg (3) to the Bench Frame (1) with two M10 x 68mm Button Bolts (79), two M10 Washers (67), and two M10 Nylon Locknuts (69).
Before beginning assembly, carefully read the following information and instructions:
Assembly requires two people.
For help identifying small parts, use the
PART
IDENTIFICATION CHART.
Tighten all parts as you assemble them, unless instructed to do otherwise.
As you assemble the weight bench, make sure all parts are oriented as shown in the drawings.
Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
The following tools (not included) are required for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly, and soapy water.
Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.
Make Things Easier for Yourself
This manual is designed to ensure that the weight bench can be assembled successfully by anyone. Most people find that by setting aside plenty of time, assembly will go smoothly.
Before beginning, make sure you under­stand the information in the box above. Note: Some parts described in the assem­bly steps may be pre-assembled.
ASSEMBLY
1
69
79
9
2
9
67
67
69
18
76
1
61
58
78
2
3
1
79
58
69
69
80
67
86
6
5. Press four 25mm Square Inner Caps (19) into the ends of the Backrest Tubes (6).
Attach the Backrest Bracket (10) to the Backrest Tubes (6) with four M10 x 45mm Button Bolts (74), four M10 Washers (67), and four M10 Nylon Locknuts (69). Make sure the Backrest Tubes
are oriented so that the indicated holes are closer to the bottom. Do not tighten the Locknuts yet.
3
4
4
25
73
11
20
72
17
17
73
24
7
69
70
75
1
Lubricate
71
1
69
77
75
Lubricate
8
5
6
19
67
67
Holes
74
74
69
69
10
19
3. Attach the Leg Lever Bracket (7) to the Bench Frame (1) with two M10 x 81mm Button Bolts (75) and two M10 Nylon Locknuts (69).
Press two 50mm Square Inner Caps (17) into the Leg Lever (4). Press a 25mm Round Inner Cap (20) into the indicated end of the Weight Tube (11).
Attach the Weight Tube (11) to the Leg Lever (4) with an M8 x 63mm Button Bolt (71), two M8 Washers (73), a 13mm Spacer (25), and an M8 Nylon Locknut (72).
Press a 25mm Round Angled Cap (24) onto the Weight Tube (11).
Lubricate the M10 x 73mm Button Bolt (70) with grease. Attach the Leg Lever (4) to the Leg Lever Bracket (7) with the Bolt and an M10 Nylon Locknut (69). Do not overtighten the Locknut;
the Leg Lever must be able to pivot easily.
4. Lubricate an M10 x 81mm Button Bolt (75) with grease. Attach the lower hole in the Adjustment Lever (8) to the Bench Frame (1) with the Bolt and an M10 Nylon Locknut (69). Do not over-
tighten the Locknut; the Adjustment Lever must be able to pivot easily.
Hold the handle on the Adjustment Lever (8) so that the upper hole is above the Bench Frame (1). Slide the M10 x 65mm Flat Head Screw (77) through the indicated side of the Lever, over the Bench Frame, and tighten it into the other side of the Adjustment Lever. Make sure that the threads
of the Screw show through the Adjustment Lever. Do not overtighten the Screw.
7
6. Insert the Backrest Bracket (10) through the slot in the Bench Frame (1) and under the Adjustment Lever (8). Make sure that the M10 x 65mm Flat
Head Screw (77) is under the Backrest Bracket arm.
Lubricate an M10 x 155mm Button Bolt (85) with grease. Attach the Backrest Tubes (6) to the Bench Frame (1) with the Bolt, two M10 Washers (67), and an M10 Nylon Locknut (69). Do not
overtighten the Locknut; the Backrest Tubes must be able to pivot easily.
8. Attach the Seat (13) to the Bench Frame (1) with an M6 x 63mm Screw (65), an M6 Washer (68), and two M6 x 16mm Screws (63).
7. Attach the Backrest (12) to the Backrest Tubes (6) with four M6 x 38mm Screws (64) and four M6 Washers (68).
Tighten the four M10 Nylon Locknuts (69) used in step 5.
6
7
8
1
85
Lubricate
67
10
77
67
6
8
69
12
68
64
68
63
65
68
13
1
64
6
8
9. Slide a Pad Tube (50) into a hole in the Leg Lever (4). Wet both sides of the Pad Tube with soapy water. Slide two Large Foam Pads (51) onto the Pad Tube as shown. Press two Large Pad Caps (53) into the Pad Tube. Repeat with
the other Pad Tube and the Leg Lever.
Slide the Long Pad Tube (82) into the hole in the Leg Lever Bracket (7). Wet both sides of the Pad Tube with soapy water. Slide two Small Foam Pads (52) onto the Tube as shown. Press two Small Pad Caps (54) into the Pad Tube.
11. Press a Round Angled Bushing (45) into a Rack Foot (35). Press a 25mm Round Inner Cap (20) into an Right Upright (62).
Attach a Guide Bar (32) to the Rack Foot (35) with an M10 x 30mm Button Screw (56) and an M10 Washer (67). Tighten the Screw.
Using a rubber mallet, tap the Right Upright (62), which has numbers on the indicated side, onto the Rack Foot (35). Attach the Right Upright to the Rack Foot with two M10 x 65mm Button Bolts (60), four M10 Washers (67), and two M10 Nylon Locknuts (69). Make sure the Bolts are inserted
from the side shown. Do not tighten the Locknuts yet.
Repeat this step with the Left Upright (31 [not shown]), Guide Bar (32), and Rack Foot (35). Insert the M10 x 65mm Button Bolts (60) from the other side.
10. Attach the Curl Pad (14) to the Curl Post (5) with two M6 x 16mm Screws (63).
9
52
52
82
54
54
53
53
51
51
4
50
7
50
10
11
14
5
63
32
Numbers
62
20
35
45
69
67
67
67
67
60
56
67
9
12. Attach a Base Cap (9) and a Rear Support (29) to the a Base (28) with two M10 x 93mm Button Bolts (48), an M10 Washer (67), an M10 Nylon Locknut (69), an M10 Nylon Jamnut (26), and an M4 x 16mm Screw (58).
Repeat this step with the other Base (28) and Rear Support (29).
14. Attach the Crossbar (30) to a Rear Support (29) with two M10 x 68mm Button Bolts (79), two M10 Washers (67), and two M10 Nylon Locknuts (69).
Do not tighten the Locknuts yet.
Attach the Crossbar (30) to the other Rear Support (29) in the same manner.
13. Attach a Base (28) to the Center Base (27) with three M10 x 68mm Button Bolts (79), three M10 Washers (67), and two M10 Nylon Locknuts (69).
Do not tighten the Locknuts yet.
Attach the other Base (28) to the Center Base (27) in the same manner.
12
29
48
48
28
67
69
58
26
9
13
14
28
79
67
69
69
27
29
30
79
79
67
67
69
10
15. Using a rubber mallet, tap the left Rack Foot (35) into the indicated Base (28). Attach the Foot to the Base with two M10 x 65mm Button Bolts (60), four M10 Washers (67), and two M10 Nylon Locknuts (69). Do not tighten the Locknuts yet.
Attach the Left Upright (31) to the Rear Support (29) with two M10 x 68mm Button Bolts (79) and two M10 Nylon Locknuts (69). Do not tighten the
Locknuts yet.
Attach the right Rack Foot (not shown) and Right Upright (not shown) in the same man­ner.
16. Attach the Right Spotter Hook (39) to a Safety Spotter (38) with an M8 x 12mm Shoulder Bolt (57) and an M8 Nylon Locknut (72). Make sure the
bolt head is on the same side as the handle.
Slide the Safety Spotter (38) onto the right Guide Bar (32) and engage the Right Spotter Hook (39) into an adjustment hole near the bottom of the Right Upright (62).
Assemble the Left Spotter Hook (40) and a Safety Spotter (38) in the same manner.
15
16
79
79
69
69
67
67
67
60
69
29
31
35
28
40
39
38
38
57
32
62
Adjustment Hole
Handle
72
17. Identify the Left and Right Barbell Gliders (37, 81) by the position of the screw holes.
Slide each Barbell Glider (37, 81) onto the Guide Bar (32) next to the indicated Upright (31, 62).
Make sure the Barbell Gliders are oriented as shown.
17
32
37
Screw
Hole
Screw
Hole
81
32
62 31
11
20. Slide a Weight Stop (42) onto the Weight Bar (33). Thread a 1/4” x 14mm Button Screw (59) into the Weight Stop and the hole in the Weight Bar. Do not tighten the Screws yet.
Thread a 1/4” x 14mm Button Screw (59) into the Left Barbell Glider (37).
Repeat this step with the Right Barbell Glider (not shown) and the other Weight Stop (not shown).
18. Press a Top Bracket Bushing (55) into the Top Bracket (36). Using a rubber mallet, tap the Top Bracket onto the Left Upright (31) and the Guide Bar (32).
Attach the Top Bracket (36) to the Left Upright (31) with two M10 x 65mm Button Bolts (60), four M10 Washers (67), and two M10 Nylon Locknuts (69). Do not tighten the Locknuts yet.
Attach the Top Bracket (36) to the Guide Bar (32) with an M10 x 30mm Button Screw (56) and an M10 Washer (67).
Assemble the other Top Bracket (36) in the same manner.
19. Slide the Weight Bar (33) through the Left Barbell Glider (37), the Locking Bar (34), and the Right Barbell Glider (81). Make sure the Locking Bar
is oriented as shown.
Engage the hooks on the Locking Bar (34) into a set of holes in the Uprights (31, 62).
21. Press a 48mm Tapered Inner Cap (46) into a Barbell Adapter (41).
Slide a Barbell Adapter (41) onto the Weight Bar (33). Thread a 1/4” x 9.5mm Allen Head Set Screw (66) into the Barbell Adapter. Do not tight-
en the Screw yet.
Repeat this step with the other Barbell Adapter (not shown).
Tighten the M10 Nylon Locknuts (69) used in steps 11–21. Tighten the 1/4” x 14mm Button Screws (59) and 1/4” x 9.5mm Allen Head Set Screw (66) used in steps 20 and 21.
20
21
18
33
37
59
59
42
33
36
31
32
60
67
67
67
69
56
67
55
41
66
46
19
34
81
37
31
62
33
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 15 for impor­tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate­ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
12
12
7
22
8
77
10
5
ADJUSTMENTS
ADJUSTING THE BACKREST
To adjust the position of the Backrest (12), hold the upper end of the Backrest with one hand and lift the Adjustment Lever (8) with the other hand, disengag­ing the Backrest Bracket (10). Raise or lower the Backrest to the desired position. Lower the Adjust­ment Lever so that the M10 x 65mm Flat Head Screw (77 [not shown]) engages one of the notches in the Backrest Bracket.
WARNING: Always hold the
Backrest (12) securely before disengaging the Backrest Bracket (10). Always make sure the Backrest Bracket is fully engaged before using the Backrest.
ATTACHING THE CURL POST
For some exercises, the Curl Post (5) must be attached to the weight bench. Slide the Curl Post into the Leg Lever Bracket (7). Align the adjustment holes in the Curl Post with the adjustment hole in the Leg Lever Bracket. Tighten the Curl Knob (22) into the adjustment hole in the Leg Lever Bracket. Fully tight-
en the Knob.
13
27
4
11
Weight
83
76
ATTACHING WEIGHTS TO THE LEG LEVER
To use the Leg Lever (4), slide the desired weights (not included) onto the Weight Tube (11). Secure the weights with a Weight Clip (83 or 84 [not shown]).
Weights can be added to the Curl Bar (not shown) in the same manner. Secure the weights to the Curl Bar with two Weight Clips (83 or 84 [not shown]).
WARNING: Do not place more
than 150 pounds on the Weight Tube (11) or the Curl Bar (47).
USING THE OLYMPIC WEIGHT ADAPTER
Press a 48mm Round Inner Cap (16) into the Olympic Adapter (15). Attach the Olympic Adapter to the Weight Tube (11) with a 1/4” x 9.5mm Allen Head Set Screw (66). Make sure that the Set Screw is in the
bottom of the Adapter.
Press a 48mm Round Inner Cap (16) into a Weight Adapter (49). Attach the Weight Adapter to the Curl Bar (47) with a 1/4” x 9.5mm Allen Head Set Screw (66). Make sure that the Set Screw is in the bot-
tom of the Adapter. Attach the other Weight Adapter to the Curl Bar in the same manner.
USING THE BENCH FOR PRESS EXERCISES
To prevent the weight rack from tipping while perform­ing press exercises on the bench, set the “L”-bracket (76) over the Center Base (27).
49
11
15
66
16
47
16
66
14
41
84
38
39
62
Handle
62
Weight
Weight
31
37
34
USING THE LOCKING BAR
Before starting an exercise, position the Locking Bar (34) and the Safety Spotters (not shown) in the correct position for the exercise.
To do this, stand in front of the rack and grip the Locking Bar (34) with both hands. Turn the Locking Bar until the two hooks disengage the slots in the Uprights (31, 62 [not shown]). Raise or lower the Locking Bar to a new position and turn it until the hooks engage the slots in the Uprights.
USING THE SAFETY SPOTTERS
To move the Safety Spotters (38) to a new position, grip the handles on the Spotter Hooks (39, 40 [not shown]) and pull the hooks out of the slots in the Uprights (31 [not shown], 62). Raise or lower the Safety Spotters to new positions and pivot the hooks back into the slots in the Uprights. Note: Always
position the Safety Spotters at the lowest point to which you want the barbell to move during the exercise.
WARNING:Always set both Safety
Spotters (38) at the same height.
ATTACHING WEIGHTS TO THE BARBELL OR THE WEIGHT CARRIAGE
To use the barbell, slide the desired amount of weight (not included) onto the Barbell Adapters (41). Secure the weights with the Large Weight Clips (84).
Your weights can be stored on the tubes on the Uprights (31 [not shown], 62) (see the inset drawing).
WARNING:Do not place more than
310 pounds on the barbell. Always place the same amount of weight on each side of the bar­bell. Always secure weights with the Large Weight Clips (84).
15
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
MUSCLE BUILDING
To increase the size and strength of your muscles, push them close to their maximum capacity. Your mus­cles will continually adapt and grow as you progres­sively increase the intensity of your exercise. You can adjust the intensity level of an individual exercise in two ways:
• by changing the amount of resistance used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an exercise, such as one sit-up. A“set” is a series of repetitions.)
The proper amount of resistance for each exercise depends upon the individual user. You must gauge your limits and select the amount of resistance that is right for you. Begin with 3 sets of 8 repetitions for each exercise you perform. Rest for 3 minutes after each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of resistance.
TONING
You can tone your muscles by pushing them to a mod­erate percentage of their capacity. Select a moderate amount of resistance and increase the number of rep­etitions in each set. Complete as many sets of 15 to 20 repetitions as possible without discomfort. Rest for 1 minute after each set. Work your muscles by com­pleting more sets rather than by using high amounts of resistance.
WEIGHT LOSS
To lose weight, use a low amount of resistance and increase the number of repetitions in each set. Exercise for 20 to 30 minutes, resting for a maximum of 30 seconds between sets.
CROSS TRAINING
Cross training is an efficient way to get a complete and well-balanced fitness program. An example of a bal­anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical or exercise bike, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body time to regenerate.
The combination of strength training and aerobic exer­cise will reshape and strengthen your body, plus devel­op your heart and lungs.
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout, as well as the number of repetitions or sets completed, is an individual matter. It is important to avoid overdo­ing it during the first few months of your exercise pro­gram. You should progress at your own pace and be sensitive to your body’s signals. If you experience pain or dizziness at any time while exercising, stop immedi­ately and begin cooling down. Find out what is wrong before continuing. Remember that adequate rest and a proper diet are important factors in any exercise pro­gram.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. Warming up prepares your body for more strenuous exercise by increasing circulation, raising your body temperature and deliver­ing more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercis­es. Select exercises for every major muscle group, emphasizing areas that you want to develop most. To give balance and variety to your workouts, vary the exercises from session to session.
Schedule your workouts for the time of day when your energy level is the highest. Each workout should be followed by at least one day of rest. Once you find the schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an effective exercise program. This requires moving through the full range of motion for each exercise, and moving only the appropriate parts of the body. Exercising in an uncontrolled manner will leave you feeling exhausted. On the exercise guide accompany­ing this manual you will find photographs showing the correct form for several exercises, and a list of the muscles affected. Refer to the muscle chart on the next page to find the names of the muscles.
The repetitions in each set should be performed smoothly and without pausing. The exertion stage of each repetition should last about half as long as the return stage. Proper breathing is important. Exhale during the exertion stage of each repetition and inhale during the return stroke. Never hold your breath.
16
Rest for a short period of time after each set. The ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning work-
out.
• Rest for 30 seconds after each set for a weight loss
workout. Plan to spend the first couple of weeks familiarizing yourself with the equipment and learning the proper form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching. Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into each stretch gradually and go only as far as you can without strain. Stretching at the end of each workout is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. The chart on pages 17–19 of this manual can be photo­copied and used to schedule and record your work­outs. List the date, the exercises performed, the resist­ance used, and the numbers of sets and repetitions completed. Record your weight and key body meas­urements at the end of every month. Remember, the key to achieving the greatest results is to make exer­cise a regular and enjoyable part of your everyday life.
A
B
C D
E
F
G
H
I
J
K
L
M N
MUSCLE CHART
O
P
Q
R
S
T
U
V W
X
A. Sternomastoid (neck) B. Pectoralis Major (chest) C. Biceps (front of arm) D. Obliques (waist) E. Brachioradials (forearm) F. Hip Flexors (upper thigh) G. Abductor (outer thigh) H. Quadriceps (front of thigh) I. Sartorius (front of thigh) J. Tibialis Anterior (front of calf) K. Soleus (front of calf) L. Anterior Deltoid (shoulder) M. Rectus Abdominus (stomach) N. Adductor (inner thigh) O. Trapezius (upper back) P. Rhomboideus (upper back) Q. Posterior Deltoid (shoulder) R. Triceps (back of arm) S. Latissimus Dorsi (mid back) T. Spinae Erectors (lower back) U. Gluteus Medius (hip) V. Gluteus Maximus (buttocks) W. Hamstring (back of leg) X. Gastrocnemius (back of calf)
17
MONDAY
Date:
/ /
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
AEROBIC EXERCISE
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
FRIDAY
Date:
/ /
Make photocopies of this page for scheduling and recording your workouts.
18
MONDAY
Date:
/ /
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
AEROBIC EXERCISE
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
FRIDAY
Date:
/ /
Make photocopies of this page for scheduling and recording your workouts.
19
MONDAY
Date:
/ /
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
EXERCISE WEIGHT SETS REPS
AEROBIC EXERCISE
AEROBIC EXERCISE
TUESDAY
Date:
/ /
WEDNESDAY
Date:
/ /
THURSDAY
Date:
/ /
FRIDAY
Date:
/ /
Make photocopies of this page for scheduling and recording your workouts.
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user’s manual for information about ordering replacement parts.
Key No. Qty. Description Key No. Qty. Description
1 1 Bench Frame 2 1 Stabilizer 3 1 Bench Leg 4 1 Leg Lever 5 1 Curl Post 6 2 Backrest Tube 7 1 Leg Lever Bracket 8 1 Adjustment Lever
9 4 Base Cap 10 1 Backrest Bracket 11 1 Weight Tube 12 1 Backrest 13 1 Seat 14 1 Curl Pad 15 1 Olympic Adapter 16 3 48mm Round Inner Cap 17 2 50mm Square Inner Cap 18 1 Notched Square Inner Cap 19 4 25mm Square Inner Cap 20 5 25mm Round Inner Cap 21 1 Handgrip 22 1 Curl Knob 23 2 Small Round Bushing 24 1 25mm Round Angled Cap 25 1 13mm Spacer 26 2 M10 Nylon Jamnut 27 1 Center Base 28 2 Base 29 2 Rear Support 30 1 Crossbar 31 1 Left Upright 32 2 Guide Bar 33 1 Weight Bar 34 1 Locking Bar 35 2 Rack Foot 36 2 Top Bracket 37 1 Left Barbell Glider 38 2 Safety Spotter 39 1 Right Spotter Hook 40 1 Left Spotter Hook 41 2 Barbell Adapter 42 2 Weight Stop 43 8 Glider Bushing 44 4 Weight Bar Glider Bushing 45 2 Round Angled Bushing 46 2 48mm Tapered Inner Cap
47 1 Curl Bar 48 4 M10 x 93mm Button Bolt 49 2 Weight Adapter 50 2 Pad Tube 51 4 Large Foam Pad 52 2 Small Foam Pad 53 4 Large Pad Cap 54 2 Small Pad Cap 55 2 Top Bracket Bushing 56 4 M10 x 30mm Button Screw 57 2 M8 x 12mm Shoulder Bolt 58 5 M4 x 16mm Screw 59 4 1/4” x 14mm Button Screw 60 12 M10 x 65mm Button Bolt 61 2 M10 x 95mm Carriage Bolt 62 1 Right Upright 63 4 M6 x 16mm Screw 64 4 M6 x 38mm Screw 65 1 M6 x 63mm Screw 66 5 1/4” x 9.5mm Allen Head Set
Screw 67 50 M10 Washer 68 5 M6 Washer 69 41 M10 Nylon Locknut 70 1 M10 x 73mm Button Bolt 71 1 M8 x 63mm Button Bolt 72 3 M8 Nylon Locknut 73 2 M8 Washer 74 4 M10 x 45mm Button Bolt 75 3 M10 x 81mm Button Bolt 76 1 “L”-bracket 77 1 M10 x 65mm Flat Head Screw 78 2 M10 x 25mm Button Screw 79 18 M10 x 68mm Button Bolt 80 1 Small Base Cap 81 1 Right Barbell Glider 82 1 Long Pad Tube 83 2 Small Weight Clip 84 2 Large Weight Clip 85 1 M10 x 155mm Button Bolt 86 1 Thin Notched Square Inner Cap
# 1 User’s Manual # 1 Exercise Guide # 1 Grease Pack # 3 Allen Wrench
PART LIST—Model No. 831.150330 R0803A
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part from the PART LIST in the center of this manual. Important:
Some parts may have been pre-assembled for shipping purposes. If a part is not in the parts bag, check to see if it has been pre-attached. If a part is missing, call toll-free 1-800-999-3756.
M10 x 30mm Button Screw (56)
M10 x 25mm Button Screw (78)
M6 x 16mm Screw (63)
M4 x 16mm Screw (58)
1/4” x 14mm Button
Screw (59)
Head Set Screw (66)
M8 x 12mm Shoulder
1/4" x 9.5mm Allen
M6 x 38mm Screw (64)
Bolt (57)
M10 x 45mm Button Bolt (74)
M8 x 63mm Button Bolt (71)
M6 x 63mm Screw (65)
M10 x 65mm Button Bolt (60)
M10 x 65mm Flat Head Screw (77)
M8 Nylon Locknut (72)
M8 Washer (73)
M10 Washer (67)
M10 x 68mm Button Bolt (79)
M10 Nylon Locknut (69)
M10 x 73mm Button Bolt (70)
M10 x 81mm Button Bolt (75)
M6 Washer (68)
M10 x 93mm Button Bolt (48)
M10 x 95mm Carriage Bolt (61)
M10 x 155mm Button Bolt (85)
EXPLODED DRAWING—Model No. 831.150330 R0803A
67
36
56
69
20
69
69
67
67
44
55
43
37
44
34
42
41
46
56
66
36
67
44
55
43
44
12
33
84
59
69
67
67
69
81
43
59
19
68
6
67
67
74
69
5
14
67
60
59
43
42
79
83
29
67
60
62
64
74
6
85
67
67
68
19
13
63
31
79
32
69
46
41
66
59
30
79
48
48
67
69
69
32
69
69
64
29
79
9
67
79
69
10
79
70
22
7
69
69
67
79
26
58
69
67
79
69
20
67
67
69
76
1
23
67
75
4
67
67
48
48
69
27
69
67
69
67
28
60
67
60
67
67
77
79
23
68
69
24
18
73
72
17
67
60
40
72
43
57
26
9
67
67
69
60
49
16
39
57
43
38
43
72
75
21
8
65
69
63
71
73
25
17
11
20
38
43
58
28
47
20
66
51
53
45
69
66
45
79
67
69
69
67
50
50
51
53
54
67
35
67
2
78
9
3
80
15
16
56
35
67
16
49
66
20
53
53
51
56
69
54
51
52
82
52
9
78
58
61
58
86
58
Part No. 199931 R0803A Printed in China © 2003 Sears, Roebuck and Co.
FULL 90-DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States and Sears will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 60179
Loading...