Proform 831299620 Owner’s Manual

Model No. 831.299620
Serial No.

Write the serial number in the space
above for future reference.

_e

rial

Number

Decal

EXIE RC I S _-

E(_ u I PM ENT

590 LS

CROSSWALK

USER'S MANUAL

[oRI n ;i_,_Bi iill Re| # nl

HELPLINE!

1-800-736-6879

SEARS, ROEBUCK AND CO.

HOFFMAN ESTATES, IL 60179

www.proform.com

new products, prizes,

fitness tips, and much morel

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS ..................................................... 2

BEFORE YOU BEGIN .................................................................. 4

ASSEMBLY ........................................................................... 5

OPERATION AND ADJUSTMENT ........................................................ 7

HOW TO FOLD AND MOVE THE TREADMILL ............................................... 10

TROUBLE-SHOOTING .............................................................. 12

CONDITIONING GUIDELINES .................................................... 14

ORDERING REPLACEMENT PARTS ............................................... Back Cover

FULL 90-DAY WARRANTY ........................................................ Back Cover

Note: An EXPLODED DRAWING is attached in the center of thMs manual.

IMPORTANT PRECAUTIONS

2

The decals shown below have been placed on your treadmill. If a decal is missing, or if it is not legible,
please call our toll-free HELPLINE to order a free replacement decal (see the front cover of this manual).

Apply the decal in the location shown.

Note: This decal is shown at 38% of actual size.

FROMTHISAREAWHILETHE
KEEPHANDSANDFEETAWAYl--

TREADMILLISINOPERATION.•

I

3

BEFORE YOU BEGIN

Congratulations for selecting the new PROFORM ®

CROSSWALK 590 LS treadmill. The CROSSWALK
590 LS treadmill combines advanced technology with

innovative design to help you get the most from your
exercise in the convenience and privacy of your home.
And when you're not exercising, the unique 590 LS can
be folded up, requiring less than half the floor space of

other treadmills.

For your benefit, read this manual carefully before
using the treadmill, If you have additional questions,

Water Bottle

Holder (Bottle

not included)

Storage Latch

please call our toll-free HELPLINE at 1-800-736-6879,

Monday through Saturday, 7 a.m. until 7 p.m. Central

Time (excluding holidays). To help us assist you,

please note the product model number and serial num-

ber before calling. The model number of the treadmill

is 831.299620. The serial number can be found on a
decal attached to the treadmill (see the front cover of

this manual for the location).

Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.

Book Holder -----_ [_--- Upper Body Arms

Key/Clip z'--- _Console

___ -- Handrail

Foot Rail

Rear Roller

Adjustment

LEFT SIDE

illOH,,,o,

Walking Belt

Circuit Breaker

Power

Cord

Front Wheel

Cushioned Walking Platform

4

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing matedals. Do not

dispose of the packing materials until assembly is completed. Refer to the drawings below to identify small parts
used in assembly. Assembly requires the following tools: The included allen wrench and your own phillips

screwdriver (]__, mallet (z_ , wire cutters _, and needle-nose pliers _.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal

condition and does not affect treadmill performance. Ifthere is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Long Screw (79)-4

1©

Screw (101)-4

1. With the help of a second person, carefully raise the

Uprights (82) untilthe treadmill is in the position shown.

Insert one of the Extension Legs (103) into the treedmill

as shown. Make sure that the Thick Base Pad (97) is on
the indicated side. Note: It may be helpful to tip the
Uprights (82) In the direction shown by the arrows as you
insert the Extension Leg. To fully insert the Extension

Leg, it may be necessary to tap it with a mallet.

Insert the other Extension Leg (not shown) in the same
way.

2. Refer to drawing 2a. If there are plastic ties in the Cage

Nuts (36) inthe Right Handrail (85), remove the plastic
ties. Pull about 6_of the Wire Hamess (17) out of the
Right Upright (82). Route the Wire Hamass through the
bracket on the Right Handrail and out of the indicated
hole. If necessary, use needle-nose pliers to gdp the con-

hectors on the Wire Harness. Thread the includedwire tie
through the indicated hole in the Right Handrail (85).

Handrail Bolt (89)-4

2a

Handrail Washer (92)-4

85

2cy23 17 _

Refer to drawing 2b. Look into the Right Handrail (85)
and make sure that the Wire Hamess (17) is on the indi-
cated side of the wire tie. Tighten the wire tie and cut the

excess off the end.

Refer to drawing 2c. Insert the bracket on the Right

Handrail (85) into the upper end of the rightUpright(82).

Hand tighten a Handrail Bolt (89) with a Handrail Washer

(92) into each side of the Upright as shown.

Attach the Left Handrail (23) as described above. Note:
There is not a wire in the left Upright (82).

5

84 92

_82 I

2b Tie

3. Withthe help of a second person, carefully tip the Uprights

(82) down as shown. Note: It may be helpful to place a
foot on one of the Wheels (95) as you tip the treadmill.

Attach each Extension Leg (103) with two Screws (101)
and a Base Pad (52) as shown. Make sure that the
Extension Legs are fully inserted into the Uprights (82);
push down on the Uprights as you tighten the Screws.

Note: One replacement Base Pad (52) and Spacer (not
shown) may be included. If a Base Pad becomes worn
and needs to be replaced, use the replacement Base

Pad. If a Thick Base Pad (97) needs to be replaced, use

the replacement Base Pad with the Spacer.

3

52

"_101

With the help of a second person, carefully tip the

Uprights (82) back to the upright position.

4. Place the Console Base (87) on the Handrails (85, 23).
Make a loop with the indicated plastic tie and insert the

two Wires (17) through the loop. Pull out just enough of
the two Wires to connect them to the connectors in the

Console Base, and then plug the Wires into the connec-

tors. Important: Make sure that the Wi=_s are fully in-
serted. Tighten the loop and cut off the excess plastic tie.
WARNING: Do not disconnect or connect the Wires

while the treadmill power cord is plugged in.

Refer to drawing 4b. Thread four Long Screws (79) intothe

Handrails (85, 23) and the Console Base (87). After all four
Long Screws have been started, tighten the Screws

until they are snug; do not overtighten the Screws.

Refer to drawing 2c. Tighten the four Handrail Bolts (89).

5. Remove the Lock Knob (105) from the Lock Pin (11).

95

4a

Tie

79

Make sure that the Lock Pin Collar (14) and the Spring

(56) are on the Lock Pin as shown. Insert the Lock Pin

into the Latch Bracket (77).

Tighten the Lock Knob (105) onto the Lock Pin (11).

105

77 14 11

6. Make sure that all parts are tightened before you use the treadmill, Keep the includedallen wrench in a

secure place. The allen wrench is used to adjust the walking belt (see page 13). To protectthe floor, place a
mat under the treadmill.