Proform 831297480 Owner’s Manual
PRO.FORM
E,,R a s, s A
I
SW :RS
Model No. 831.297480
Serial No.
Thesedalnumberisfoundinthelocation
shownbelow.Writetheserialnumberin
thespaceaboveforfuturereference.
Sedal Number
F-x E_. R C i S lEE
EQUIPMENT
L¶m,m =m.-m-- ...-- _m.-_
HELPLINE!
1-800-736-6879
USER'S MANUAL
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
TABLE OF CONTENTS
IMPORTANTPRECAUTIONS ....
BEFORE YOU BEGIN .......................................
ASSEMBLY ......................................................................
OPERATION AND ADJUSTMENT .................................. . . . .. . , ...........
HOW TO FOLD AND MOVE THE TREADMILL ..........................................
TROUBLE-SHOOTING ....................................................... . ... .
CONDITIONING GUIDELINES ..................................................... ..
o= e,.e° o.oo,4o o.,, oo,oQ= o..oopm.o ooooom.o, o°,o, °,o,._o,°_oee_*
o • ° o
...... .o.oo. ............... .4
...... ,..5
_e,eeeoee7
....... ,11
........ 12
........ 14
ORDERING REPLACEMENT PARTS ...................................... ... .... .... . BackCover
FULL 90 DAY WARRANTY ................................................... ......... Back Cover
Note: A HARDWARE IDENTIFICATION CHART, aP F_,XPLODEDDRAWING, and a PART UST are attached to
the center of this manual. Please save them for future reference.
IMPORTANT PRECAUTIONS
2
The decal shown at the right has been
placed on your treadmill. If the decal Is
missing, or if it is not legible, please call
our toll-free HELPLINE to order a free re-
placement decal (see the back cover of
this manual). Apply the decal in the loca-
tion shown.
J_ WARNI..NG!
• Never allow ch,ldren
to play on or around
• treadmill.
5torage latch must be
fully en.qaged before
treadmill is moved or
stored.
o oII
© 1
o °11
3
BEFORE YOU BEGIN
Thank you for selecting the PROFORIVP CROSSWALK
PLUS treadmill. The CROSSWAIJ( PLUS treadmill
blends advanced technology with Innovative design to
letyou enjoy an excellent form of cardiovascular exer-
cise in the convenience and privacy of your home.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our toll-free HELPL|NE .at1-800-736-6879,
Monday through Saturday, 7 a.m. until7 p.m. Central
Accesso_Trey
Time (excluding holidays). To help us assist you,
please note the product model number and eadal num-
ber before calling. The model number of the treadmill
is 831.297480. The sedal number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the partsthat are
labeled.
Book Rack
Holder (Water
Bottle is not
Included)
LlpperBody
Arms
BACK
Rear Roller
Adjustment Bolt
;ushloned Walking
Ptatform
FRONT
RIGHT SIDE
4
ASSEMBLY
CAUTION: Read and follow step I below before removing the r_lnlng fie (see drewlng 1). If the restral.n-
Ing fie is removed prematurely, esdous bodily Injury may result. Assembly requires two people. Set the tread-
mill in a cleared ares and remove the packing materials except for the restraining tie. Do not dispose ofthe
pacldng materials until assembly iscompleted. Use the HARDWARE IDENTIFICATION CHART inthe center ofthis
manual to identifythe pads used in assembly. Assembly requires the Included allen wrench L, a phillips
screwdriver -=====_, and two adjustable wrenches €1:_=_.
1. Slide the Left Upright (1) onto the left side of the Base
(59). It may be necessary to firmly push down on the
Left Upright until it is fully seated on the Base.
Remove the restraining tie from the Base.
Attach the lefthandrailto the Base (59) with a Handrail
Bolt(93), 3/8" Washer (67), and Handrail Nut (4). Do not
tighten the Handrail Bolt yeL Using the allen wrench,
tighten two UprightScrews (63) intothe Left Upright (1)
and the Base.
2. Slide the Right Upright (44) onto the right side of the
Base (59). It may be necessary to firmly push down
on the Right Upright until it is fully seated on the
Base. Be careful not to pinch the Wire Harness (25)
between the Right Upright and the Base.
Restraining
59
Attach the right handrail to the Base (59) with a Handrail
Boll (93), 3/8" Washer (67), and Handrail Nut (4). Do not
tighten the Handrail Bolt yet. Using the allen wrench,
tighten two Upright Screws (63) into the Right Upright
(44) and the Base.
Hand tighten the Handrail Nuts (4) used in steps I and 2.
Using a wrench, tighten the Handrail Bolts (93) used in
steps 1 and 2. Remove the wire ties (not shown) attach-
ing the Console Base (9) to the Right Upright (44).
3. Set the Console Base (9) on the Left and Right Updghts
(1, 44). Attach the Console Base with four Screws (75).
While one person carefully feed= any slack Wire Hamess
(25) down into the Right Upright (44), a second person
should carefully pull the slack Wire Harness from the
lower end of the Right Upright.
Align the holes !n the Book Rack (62) with those in the
Console BaseJ'9). Attach the Book Rack to the Console
Base with four Screws (75) as shown.
75
75
5
4. With the help of a second person, carefully lower the Left
and Right Uprights (1,44) untilthe handrails are resting
on the floor.
1
Attach six Base Pads (57) to the bottom of the Base (59)
in the indicated locations. Note: One extra Base Pad
may be included.
See drawing 4 above. With the help of a second person,
raise the Left and Right Updghts (1,44) until the Base
(59) is restingfiat on the floor.
Before moving the treadmill, see HOW TO MOVE THE
TREADMILL on page 11.
4
6. Insed two Resistance Bracket Bolts (107) with Bracket
WasherS (70) into the Left Updght (.1). Slide two Star
Washers.(.€03), a_,p_.r..(106), ,andtwo more Star
•Washers (103) onto the Bolts. Make sure that the
Spacer is turned so the widest slde is facing the Left
UpdghL Tighten the Boltsinto the Resistance Bracket
(104) at the lower end of the left Upper Body Arm (96).
(Note: It may be necessary to loosen the Resistance
Knob [97] and pivotthe Resistance BmckeL)
Attach the right Upper Body Arm (96) as desqdbed
above. Make sure that both Upper Body Arms are on the
correct side of the Console Base (9) as shown.
See drawing 2 on page 5. Feed the slack Wire Hameas
(25) intothe Base (59).
6
7. Remove the backing from the Adhesive Clip (7"/). Press
the Adhesive Clip onto the Rear Roller Endcap (78) in the "
indicated location. Press the Allen Wrench (76) into the
Adhesive Clip.
Make sure that all partsare tightened before you use the
treadmill. Note: To protect the floor or carpet, place a
mat under the treadmill. For Information On ordering a
mat, see REPLACEMENT PARTS on the back cover.
76
Loading...