Proform 831297364 Owner’s Manual
I I IIIIIIIIIII IIII II I I II
ER O
SE / S
Model No. 831_9_64
Serial No.
The sedalnumberisfoundinthelocation
shownbelow.Writetheserialnumberin
theSPaCeabovefor futurereference.
Sedal Number
E_X E£: RC I S E_
EQUIPMENT
HELPLINE!
1-800-736-6879
USER'S MANUAL
SEARS, ROEBUCK AND CO, HOFFMAN ESTATES, IL 60179
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ................... .
ASSEMB'_'.......... :::: :: :::: ::
OPE_TION AND ADJUSTMENT .................
HOW TO FOLD AND MOVE THE TI:I_DMIIA- ......
TROUBLE,.SHOOTING .........................
CONDITIONING GUIDELINES .......................................... . . .
ORDERING REPLACEMENT PARTS ........... Back Cover
FULL 90 DAY WARFI.q_ ............... Back Cover
Note: A HARDWARE IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART UST and am attached
to the center of this manual. Please save them for future reference.
°1_ • 1oooo ,o °°o o.°. °_°o o_
• =.o ,,,,t • • • ,,,_•,_ Q o J ... *•I*Q Q ° •• ° aqa•
IolqoooleQo=oog_
!........."........7••
• *o_o II • •
................. 14
....... 10
.... 12
IMPORTANT PRECAUTIONS
2
Thedecalshownattherighthasbeen
placedonyourtreadmill.Ifthedecalis
missing_orif itisnotlegible,pleasecall
ourtoll-freeHELPLINEtoorderafreere-
placementdecal(seethebackcoverof
thismanual).Applythedecalintheloca-
tionshown.
AWARNING!
• Storage latch must be
fully engaged before
treadmill is moved or
stored.
° °II
© 1
° °11
3
BEFORE YOU 13EGIN
Thank you for selecting the PROFORk, P CROSS-
WALK SI treadmill. The CROSSWALK SI treadmill
blends advanced technology with Innovative design to
let you enjoy an excellent form of cardiovascular exer-
cise In the convenience and pdvacy of your home.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our toU-free HELPUNE at 1-800-736-6879,
Monday through Saturday, 7 a.m. until 7 p.m. Central
AccessoryTray
Time (excluding holidays). To help us esslst you,
please note the product model number and Serial num-
ber before calling. The model number ofthe treadmill
is831.297364. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please mvtew the drawing
below and familiarize yourself with the pads that are
labeled.
Rack
"Bottle
Holder(Water
Boffieisnct
Induded)
Upper Body
Arms
BACK
Rear Roller
Adjustment Bolt
Handrails
FRONT
WalldngBelt_
FootRails
RIGHT SIDE
Platform
4
ASSEMBLY
CAUTION: Read and follow step I below before rernovlng the restraining Ue (sep cl_'a_ng "1).ffthe restrain-
ing tie Is removed prematurely, serious bodily injury may result. Assembly requires_v/o people.. Set the tread-
mill in a cleared area and remove the packing materials except for the restraining tle"Do not dispose of the
packing materials untilassembly Iscompleted. Use the HARDWARE IDENTIRC_.TION CHART in the center of
this manual to identify the parts used in assembly. Assembly requires the Included allen wrench L==-, a
phillips screwdriver ..==_, and two adjustable wrenches G_==:_.
1. Slide the Left Upright (1) onto the left side of the Base
(59). It may be necessary to firmly push down on the
Left Upright until it Is fully seated on the Base.
Remove the restrainingtie from the Base.
Attach the left handrailto the Base (59) witha Handrail
Bolt(93), 3/8" Washer (67), and Handrail Nut (4). Do not
tighten the Handrail Bolt yeL Using the allen wrench,
tighten two UprightScrews (63) with two of the four
Updght Washers (111) intothe Left Updght (1) and Base. Restralnlng
2. Slide the Right Upright (44) onto the rightside of the
Base (59). It may be necessary to firmly push down
on the Right Upright until it is fully seated on the
Base. Be careful not to pinch the Wire Harness (25)
between the Right Updght and the Base.
Attach the right handrail to the Base (59) with a Handrail
Bolt (93), 3/8" Washer (67), and Handrail Nut (4). Do not
tighten the Handrail Bolt yet. Using the allen wrench,
tighten two Updght Screws (63) withthe remaining Upright
Washers (111) into the Right Upright (44) and Base.
Hand tighten the Handrail Nuts (4) used insteps I and 2.
Using a wrench, tighten the Handrail Bolts (93) used in
steps I end 2.
Remove the wire ties (not shown) attaching the Console
Base (9) to the Right Upright(44).
3. Set the Console Base (9) on the Left and Right Updghts
(1, 44).
While one person carefully fesds any slack Wire Hamess
(25) down intothe Right Upright (44), a second person
should carefully pullthe slackWire Hamess from the
lower end of the Right Upright.
Attach the Console Base (9) withfour Screws (75).
Align the holes in the Book Rack (62) with those in the
Console Base (9). Attach the Book Rack to the Console
Base with four Screws (75) as shown.
75
4. With the help of a secondperson, carefully lower the Left
and Right Uprights(1, 44) until the handrails are resting
on the floor.
. Attach six Base Pads (57) to the bottom of the Base (59)
in the indicated locations.Note: An extra Base Pad may
be included.
(See drawing 4 above.) With the help of a second person,
raise the Left and Right Uprights (1, 44) until the Base
(59) is resting flat on the floor.
Before moving the treadmill, see HOW TO MOVE THE
TREADMILL on page 11.
. •
44
59
Remove the Resistance Knob (97), 3/8" Washers (67),
So
Spdng Washer (5), Thrust Washers (101), Thrust Bearing
(102), and Resistance Cone (98) from the Resistance
Boll (105). Be sure to keep all parts in order. Insert one
of the Upper Body Arms (96) into the Resistance Cone
(98), making sure that it is turned as shown. Slide all
parts back onto the Resistance Boll (105). Refer to the
HARDWARE IDENTIFICATION CHART to make sure
that all partsare in the correct order. Tighten the
Resistance Knob (97) onto the Res!stance Boll
Insert two Resistance BracketBolts (107) with Bracket
Washers (70) into the LeftUpdght (1). Slide two Star
Washers (103), a Spacer (106), and two more Star
Washers (103) onto the Bolts.Tighten the Bolts into the
:Resistance Bracket (104). (Note: It may be necessary to
loosen the Resistance Knob [97] and pivotthe
Resistance Bracket.)
Attach the other Upper BodyArm (96) as descn'bed
above. Make sure that bothUpper Body Arms are in the
position shown onpage 4. Feed the slack Wire Harness
(25) into the Base (59).
105
Body
Arm must be
tumed in this
direction
104 --96
102
97
.
Remove the backing from the Adhesive Clip (77). Press
the Adhesive Clip onto the Rear Roller Endcap (78) in the
indicated location. Press the AllenWrench (76) into the
Adhesive Clip.
Make sure that all parts are tightened before you use the
treadmill. Note: To protect the floor or carpet, place a
mat under the treadmill. For information on ordering a
mat, see REPLACEMENT PARTS on the back cover.
6
7
78
76
Loading...