Proform 831216412 Owner’s Manual
Model No. 83t.2t64t.2
Serial No.
Serial Number
• Assembly
• Operation
• Maintenance
• Part List and Drawing
BIKE EXERCISER
User's Manual
Decal
Sears, Roebuck and Co., Hoffman Estates, IL 60179
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS ................................................................ 2
BEFORE YOU BEGIN ...................................................................... 3
ASSEMBLY ............................................................................... 4
HOW TO OPERATE THE EXERCISE CYCLE .................................................... 8
MAINTENANCE AND TROUBLESHOOTING ................................................... 16
CONDITIONING GUIDELINES ............................................................... 17
PART LIST .............................................................................. 18
EXPLODED DRAWING .................................................................... 19
ORDERING REPLACEMENT PARTS .................................................. Back Cover
90 DAY FULL WARRANTY .......................................................... Back Cover
2
BEFORE YOU BEGIN
Congratulations for selecting the new PROFORM ®XP
100 U exercise cycle. Cycling is one of the most
effective exercises for increasing cardiovascular fit-
ness, building endurance, and toning the entire body.
The XP 100 U exercise cycle offers a selection of fea-
tures designed to let you enjoy this healthful exercise
in the convenience and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle. If you have questions
after reading this manual, call 1-800-4-MY-HOME ®
(1-800-469-4663). To help us assist you, please note
the product model number and serial number before
contacting us. The model number is 831.21641.2. The
serial number can be found on a decal attached to the
exercise cycle (see the front cover of this manual for
the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Pulse Sensor Fan
Console
Water Bottle Holder £
Seat
Seat Post
Seat Knob
• Misuseof this machine
may result in serious
injury,
• Read user's man_uall
prior to useand follow
all warnings and
instructions.
• Do not allow children
on or around machine.
• Peda s continue to
sp n when you stop
pedaling.
• Spinning pedals can
cause injury.
• Reduce pedal speed
in acontrolledmanner.
• User weight must not
exceed 250 pounds.
• Replace label if
damaged, illegible, or
removed,
REAR
Pedal/Strap
RIGHT SIDE
*No water bottle is included
3
ASSEMBLY
Assembly requires two persons. Place all parts of the exercise cycle in a cleared area and remove the packing
materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included tools and your own adjustable wrench _ and Phillips
screwdriver _.
Use the part drawings below to identify the small parts used in assembly. The number in parentheses below
each drawing refers to the key number of the part, from the PART LIST on page 18. The second number refers
to the quantity needed for assembly. Note: Some small parts may have been pre-attached for shipping. If a
part is not in the parts bag, check to see if it has been pre-attached. If a part is missing, call toll-free
t-888-533-t 333.
M8 Nylon
Locknut (37)-4
M10 x 20mm Button
Screw (35)-3
1. Identify the Front Stabilizer (2), which is narrower than
the Rear Stabilizer (not shown). While another person
lifts the front of the Frame (1), attach the Front
Stabilizer to the Frame with two M10 x 74ram Button
Screws (33).
M8 Split M10 Split M4 x 22ram
Washer (36)-4 Washer (34)-3 Screw (15)-2
M4 x 16ram
Screw (41)-4
M10 x 74ram Button Screw (33)-4
2
33
4
2. While another person lifts the rear of the Frame (1),
attach the Rear Stabilizer (14) to the Frame with two
M1O x 74mm Button Screws (33).
14
3. While another person holds the Upright (3) near the
Frame (1), connect the Upper Wire Harness (32) to the
Lower Wire Harness (31).
Gently pull the upper end of the Upper Wire Harness
(32) to remove the slack, and slide the Upright (3) onto
the Frame (1). Be careful to avoid pinching the Wire
Harnesses. Attach the Upright with three M10 x 20mm
Button Screws (35) and three M10 Split Washers (34).
4. Attach the Water Bottle Holder (29) to the Upright (3)
with two M4 x 22mm Screws (15).
3
Be careful to avoid
pinching the Wire
Harnesses (31, 32)
34 35
\
4
29
15
5
5. The Console (6) requires four "D" batteries (not
included); alkaline batteries are recommended.
IMPORTANT: If the exercise cycle has been
exposed to cold temperatures, allow it to warm to
room temperature before inserting batteries into
the Console• If you do not do this, the console dis-
plays or other electronic components may become
damaged. Press the tab on the battery cover and
remove the battery cover. Insert four batteries into the
console; make sure that the batteries are oriented
as shown• Then, reattach the battery cover.
5
_ 6Batt rl
• _j e 'es
attverr,
Batteries _)
6. While another person holds the Console (6) near the
Upright (3), connect the console wire harness to the
Upper Wire Harness (32).
Insert the excess Wire Harness (32) downward into the
Upright (3). Attach the Console (6) to the Upright with
four M4 x 16mm Screws (41). Make sure that the
Wire Harness is not pinched.
7. Attach the Seat (12) to the Seat Post (5) with four M8
Nylon Locknuts (37) and four M8 Split Washers (36).
Note: The Nylon Locknuts and Split Washers may
be preattached to the Seat.
6
Console Wire
Harness
41
\
6
7
37
36
Loading...