Model No. 831.24723.7
Serial No.
TREADMILL EXERCISER
Write the serial number in the space
above for future reference.
Serial
Number
Decal
• Assembly
• Operation
• Maintenance
• Part List and Drawing
User’s Manual
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
PERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
O
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
90 DAY FULL WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
The decals shown here have been applied in the locations shown. If a decal
is missing or illegible, call 1-888533-1333 and request a free replacement decal. Apply the decal in
the location shown. Note: The decals
may not be shown at actual size.
2
IMPORTANT PRECAUTIONS
WARNING: T
structions in this manual and all warnings on your treadmill before using your treadmill. Sears assumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons
with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill.
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
8. The treadmill should be used only by persons
weighing 250 lbs. (113 kg) or less.
o reduce the risk of serious injury, read all important precautions and in-
should be on the same circuit. Do not use an
extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local Sears store or call the telephone
number on the back cover of this manual and
order part number 146148, or see your local
electronics store.
13. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 18 if the treadmill is
not working properly.)
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 13).
9. Never allow more than one person on the
treadmill at a time.
Wear appropriate exercise clothes when
10.
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women.
Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
11. When connecting the power cord (see page
11), plug the power cord into a surge suppressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
17. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails or crosswalk arms while using the
treadmill.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensor is not a medical device.
Various factors, including the user's move
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
3
-
0. Never leave the treadmill unattended while it
2
s running. Always remove the key, unplug
i
the power cord, and switch the reset/off circuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 17.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4. Inspect and properly tighten all parts of the
2
readmill regularly.
t
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning the
readmill, and before performing the mainte-
t
nance and adjustment procedures described in
this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
4
BEFORE YOU BEGIN
hank you for selecting the revolutionary PROFORM
T
ROSSWALK 415 treadmill. The CROSSWALK 415
C
treadmill offers an impressive array of features designed to make your workouts at home more enjoyable
and effective. And when you’re not exercising, the
unique CROSSWALK 415 treadmill can be folded up,
requiring less than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Crosswalk Arm
Accessory Tray
Handrail
Storage Latch
®
ng this manual, please see the front cover of this man-
i
al. To help us assist you, note the product model num-
u
ber and serial number before contacting us. The model
number and the location of the serial number decal are
shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Book Holder
Console
Pulse Sensor
Key/Clip
Upright
Walking Belt
Foot Rail
Rear Roller
Adjustment Bolts
Reset/Off
Circuit Breaker
Power Cord
Platform Cushion
5
ASSEMBLY
Base Pad Spacer
(104)–2
M8 Star
Washer (10)–4
M10 Star
Washer (8)–8
M4 x 19mm
Screw (1)–6
M8 x 25mm Bolt (6)–4
1/2" Screw
(22)–1
1/4" Washer
(9)–4
M4 x 25mm
Screw (2)–4
1/4" x 3 1/2" Bolt (4)–4
M10 x 96mm Bolt (5)–4
Bolt Spacer (79)–4
ssembly requires two persons.Set the treadmill in a cleared area and remove all packing materials. Do not
A
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver and
adjustable wrench .
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. Extra hardware may be included. If a part is missing, call 1-888-533-
1333. To avoid damaging plastic parts, do not use power tools for assembly.
1. Make sure that the power cord is unplugged.
With the help of a second person, carefully
the treadmill onto its left side. Partially fold the
Frame (48) so that the treadmill is more stable;
do not fully fold the Frame yet.
Cut the tie securing the Upright Wire (77) to the
Base (85). Locate the tie in the indicated hole in
the Base, and use the tie to pull the Upright Wire
out of the hole.
Attach a Base Pad (81) to the Base (85) in the
location shown with a Base Pad Spacer (104)
and an M4 x 25mm Screw (2). Then, attach another Base Pad (81) with only a Screw (2).
tip
1
48
6
Tie
85
104
77
81
2
Hole
81
2
. Remove the M10 Nut (33) and the M10 x 50mm
2
Bolt (27) from the Base (85). Attach a Wheel
(86) with the Bolt and the Nut that you just removed. Do not overtighten the Nut; the Wheel
must turn freely.
2
7
7
7
2
85
86
33
3. Identify the Right Upright (78) and the Right
Upright Spacer (80), which are marked with
stickers. Insert the Upright Wire (77) through the
Right Upright Spacer as shown.
See the inset drawing. Tie the wire tie in the
Right Upright (78) securely around the end of
the Upright Wire (77). With the help of a second
person, hold the Right Upright near the Base
(85). Then, pull the other end of the wire tie until
the Upright Wire is routed completely through
the Right Upright.
4. Hold a Bolt Spacer (79) inside the lower end of
the Right Upright (78). Insert an M10 x 96mm
Bolt (5) with an M10 Star Washer (8) into the
Right Upright and the Bolt Spacer. Repeat this
step with a second Bolt Spacer (79), M10 x
96mm Bolt (5), and M10 Star Washer (8).
Hold the Right Upright Spacer (80) and the
Right Upright (78) against the Base (85). Be
careful not to pinch the Upright Wire (77).
Finger tighten the M10 x 96mm Bolts (5); do not
fully tighten the Bolts yet.
Press a Base Endcap (82) into the Base (85).
3
77
4
77
78
Wire
Tie
78
85
85
Wire Tie
78
77
80
5
8
77
79
82
79
80
7
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
rame (48) so the treadmill is more stable; d
F
not fully fold the Frame yet.
5
o
Attach a Base Pad (81) to the Base (85) in the
location shown with a Base Pad Spacer (104)
and an M4 x 25mm Screw (2). Then, attach another Base Pad (81) with only a Screw (2).
Remove the M10 Nut (33) and M10 x 50mm Bolt
(27) from the Base (85). Attach a Wheel (86)
with the Bolt and the Nut that you just removed.
Do not overtighten the Nut; the Wheel must
turn freely.
6. With the help of a second person, hold a Bolt
Spacer (79) inside the lower end of the Left
Upright (73). Insert an M10 x 96mm Bolt (5) with
an M10 Star Washer (8) into the Left Upright
and the Bolt Spacer. Repeat this step with a
second Bolt Spacer (79), M10 x 96mm Bolt
(5), and M10 Star Washer (8).
Orient the Left Upright (73) and the Left Upright
Spacer (83) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(85). Finger tighten the M10 x 96mm Bolts (5);
do not fully tighten the Bolts yet.
85
81
2
104
2
6
5
8
83
79
79
82
85
48
27
86
81
33
73
Press a Base Endcap (82) into the Base (85).
With the help of a second person, tip the treadmill so that the Base (85) is flat on the floor.
7. Set the Console (87) face down on a soft surface to avoid scratching the Console. Identify
the Right Handrail (90), which has a large hole
in the location shown. Hold the Right Handrail
near the Console. Attach the console ground
wire to the Right Handrail with a 1/2" Screw (22).
Next, insert the console wire into the large hole
in the Right Handrail (90) and out of the top as
shown. Attach the Right Handrail with three M4
x 19mm Screws (1). Make sure that no wires
are pinched. Start all three Screws before
tightening any of them; do not overtighten
the Screws.
Attach the Left Handrail (not shown) to the
Console (87) in the same way.
no wires on the left side of the Console.
Note: There are
7
90
Console
Ground Wire
87
22
Console
1
Wire
Large Hole
1
8
8. Have a second person hold the console assem-
ly near the Right Upright (78). Remove the wire
b
tie from the Upright Wire (77) and console wire.
Cut the plastic ties from the brackets on the Right
Handrail (90) and Left Handrail (not shown).
Connect the Upright Wire (77) to the console
wire.
See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON.
the Right Upright (78).
Set the console assembly on the Right Upright
(78) and the Left Upright (not shown). Make sure
that no wires are pinched.
Then, insert the connectors into
8
90
77
Console Wire
Console Assembly
Console
Wire
9. Finger tighten two M8 x 25mm Bolts (6) with two
M8 Star Washers (10) into the Left Upright (73)
and the Left Handrail (89).
Next, finger tighten two M8 x 25mm Bolts (6)
with two M8 Star Washers (10) into the Right
Upright (78) and the Right Handrail (90). Then,
tighten all four Handrail Bolts.
See steps 4 and 6. Tighten the four M10 x
96mm Bolts (5).
78
9
89
6
6
10
73
77
6
90
10
10
6
78
9
10. Press the Latch Insert (70) into the Left Upright
73).
(
0
1
Locate the Latch Pin (72). Remove the knob
from the Latch Pin. Make sure that the collar
nd the spring are on the Latch Pin. Insert the
a
Latch Pin into the Latch Insert (70), and tighten
the knob back onto the Latch Pin.
Orient the Left Crosswalk Arm (71) as shown.
11.
ttach the Left Crosswalk Arm to the Left Upright
A
(73) with two 1/4" x 3 1/2" Bolts (4), two 1/4"
Washers (9), and two M10 Star Washers (8).
Make sure that the Left Crosswalk Arm is on
the side of the Console (87) shown.
Attach the Right Crosswalk Arm (not shown)
in the same way.
Knob
70
Spring
Collar
72
73
11
87
71
73
8
9
4
12. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt (see
pages 19 and 20).
10
OPERATION AND ADJUSTMENT
HE PRE-LUBRICATED WALKING BELT
T
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply sil-
cone spray or other substances to the walking
i
elt or the walking platform. Such substances will
b
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local Sears store or call the telephone number
on the back cover of this manual and order part
number 146148, or see your local electronics store.
n equipment-grounding conductor and a grounding
a
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
ccordance with all local codes and ordinances.
a
mportant: The treadmill is not compatible with
I
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Grounding Pin
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Plug
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpectedly, which may result in a fall and serious injury.
This product must be grounded.
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec
tric shock. This product is equipped with a cord having
If it should malfunc-
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw.
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
-
Some 2-pole receptacle outlet box
1112
CONSOLE DIAGRAM
Note: If there are sheets of clear plas-
Key
tic on the console, remove the plastic.
FEATURES OF THE CONSOLE
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable.
When you use the manual mode, you can change the
speed and incline of the treadmill with the touch of a
button. As you exercise, the console will display instant
exercise feedback. You can even measure your heart
rate using the handgrip pulse sensor.
In addition, the console offers six iFit custom-fit preset
workouts; three of these use the crosswalk arms. Each
workout automatically controls the speed and incline of
the treadmill as it guides you through an effective exer
cise session.
Clip
To use the manual mode of the console, follow the
steps beginning on page 13. To use a preset work-
out, see page 15.
IMPORTANT: If there is a sheet of clear plastic on
the console, remove the plastic. To prevent damage to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if necessary (see pages 19 and 20).
ote: The console can display speed and distance in
N
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea
-
surement, see THE INFORMATION MODE on page
16. Note: For simplicity, all instructions in this section
refer to miles.
-
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
old temperatures, allow it to warm to room tem-
c
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
lug in the power cord (see
P
page 11). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Switch the circuit
breaker to the reset position.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
16 to turn off the demo mode.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 12)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.
Reset
Position
1. Insert the key into the console.
See HOW TO TURN ON THE POWER to the left.
2. Select the manual mode.
hen the key is inserted, the manual mode will be
W
selected. If a preset workout has been selected, remove the key and then reinsert it.
3. Start the walking belt.
To start the walking belt, press the Go button, the
Speed increase button, or one of the speed buttons
numbered 2 through 10.
If you press the Go button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase and
decrease buttons. Each time you press a button,
the speed setting will change by 0.1 mph; if you
hold down a button, the speed setting will change
in increments of 0.5 mph. Note: After you press a
button, it may take a moment for the walking belt to
reach the selected speed setting.
If you press one of the numbered speed buttons, the
walking belt will gradually increase in speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To restart
the walking belt, press the Go button or the Speed
increase button.
4. Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
ncline increase or de-
I
crease buttons. Each time
you press the Incline increase or decrease button, the incline will change by 0.5%. Note:
press a button, it may take a moment for the treadmill to reach the selected incline setting.
After you
13
5. Follow your progress with the displays.
6. Measure your heart rate if desired.
The lower left display—
s you exercise, the
A
lower left display can
show the elapsed time
and the distance that you
ave walked or run. The
h
ower left display will also show the incline of the
l
treadmill each time the incline level changes.
The lower right display—The lower right
display can show the approximate number of
calories that you have
burned and the speed of
the walking belt. The display also shows your heart
rate when you use the handgrip pulse sensor (see
step 6).
The upper dis-
—The upper
play
display can show
the elapsed time,
the distance that
you have walked
or run, the approximate number of calories that you
have burned, or the speed of the walking belt. Press
the Display button repeatedly until the upper display
shows the information that you are most interested
in viewing. Note: While information is shown in the
upper display, the same information will not be
shown in the lower displays.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
Before using the
andgrip pulse
h
sensor, remove
the sheets of
clear plastic from
he metal con-
t
acts on the pulse
t
bar. In addition,
make sure that
your hands are clean.
To measure your heart rate,
rails and hold the pulse bar with your palms on the
metal contacts. Avoid moving your hands. When
your pulse is detected, a heart symbol in the lower
right display will flash each time your heart beats,
one or two dashes will appear, and then your heart
rate will be shown.
rate reading, continue to hold the contacts for
about 15 seconds.
7. When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
or you may damage the treadmill when you fold
it to the storage position. Next, remove the key
from the console and put it in a secure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmill’s electrical components may wear prematurely.
For the most accurate heart
Contacts
stand on the foot
14
HOW TO USE A PRESET WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on
page 13.
. Select a preset workout.
2
To select a preset workout, press the Select
Workout button repeatedly until the number of
the desired workout appears in the upper display. Note: The name, number, and profile of each
workout is listed on the console.
When you select a preset workout, the incline level
of the workout will flash in the lower left display, the
speed setting will flash in the upper display, and
then the workout length will appear in the lower left
display.
3. Select length of workout if desired.
If you have selected workout 1, 2, or 3, you can set
the length of the workout to a time between 15 and
45 minutes, in increments of 5 minutes. To set the
length of the workout press the Set Time increase
or decrease button until the desired time is selected. The new workout settings will appear in the
displays.
4. Press the Go button or the Speed increase button to start the workout.
Tones will sound at the end of each segment.
hree seconds before the speed and/or incline of
T
the treadmill is about to change, the Speed display
nd/or Incline display will flash and a series of tones
a
will sound to alert you. The treadmill will then automatically adjust to the speed and/or incline settings
for the next segment.
f you have selected workout 4, 5 or 6, you will be
I
prompted to use the crosswalk arms. When the
crosswalk indicator on the console lights up, move
the crosswalk arms forward and backward as you
walk or run on the treadmill. This action exercises
your arms, shoulders, and back for a total body
workout.
The workout will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or incline
buttons;
workout begins, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Go button.
The walking belt will begin to move at 1 mph. When
the next segment of the workout begins, the treadmill will automatically adjust to the speed and incline
settings for the next segment.
5. Follow your progress with the displays.
however, when the next segment of the
A moment after you press the button, the treadmill
will automatically adjust to the first speed and incline settings of the workout. Hold the handrails and
begin walking.
Each workout is divided into 30 one-minute segments, unless you have changed the length of the
workout (see step 3). One speed setting and one
incline setting are programmed for each segment.
Note: The same speed setting and/or incline setting
may be programmed for consecutive segments.
See step 5 on page 14.
6. Measure your heart rate if desired.
See step 6 on page 14.
7. When you are finished exercising, remove the
key from the console.
See step 7 on page 14.
15
THE INFORMATION MODE
HOW TO USE THE CROSSWALK ARMS
The console features an information mode that keeps
rack of the total distance that the walking belt has
t
moved and the total number of hours that the treadmill
has been used. The information mode also allows you
to select a measurement system of miles or kilome-
ers, and turn on and off the display demo mode.
t
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
An “E” for English miles or
an “M” for metric kilometers
will appear in the lower right
display. Press the Speed increase button to change the
unit of measurement if desired.
The lower left display will
show the total number of
miles (or kilometers) that the
walking belt has moved.
As you walk on the treadmill, you can hold the
andrails or use the crosswalk arms. To exercise your
h
arms, shoulders, and back for a total body workout,
move the crosswalk arms forward and backward as
you walk on the treadmill.
o vary the intensity of your upper body exercise, the
T
resistance of the crosswalk arms can be adjusted. To
increase the resistance, turn the resistance knobs
clockwise; to decrease the resistance, turn the knobs
counterclockwise.
Crosswalk
Arms
The upper display will show
the total number of hours
the treadmill has been used.
Note: The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. While the demo mode is turned on, the console
will function normally when you plug in the power cord,
switch the circuit breaker to the reset position, and insert the key into the console. However, when you re
move the key, the displays will remain lit, although the
buttons will not function. If the demo mode is turned on,
a “d” will appear in the lower right display while the in
formation mode is selected. To turn on or off the demo
mode, press the Speed decrease button.
To exit the information mode, remove the key from the
console.
-
-
Resistance
Knobs
16
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
efore folding the treadmill, adjust the incline to the
B
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic
foot rails. Make sure to bend your legs and keep your
back straight as you raise the frame.
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the latch pin is
aligned with the gap between the frame and the platform,
and then slowly release the latch knob.
the latch pin is fully inserted into the gap.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° F (30° C).
Raise the frame
Make sure that
Frame
Latch
Knob
Pin
HOW TO MOVE THE TREADMILL
Frame
Before moving the treadmill, convert it to the storage position
as described above. Make sure that the frame is held se-
curely by the latch pin.
Handrail
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheels
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left. It may be necessary to
push the frame forward as you pull the knob to the left. Pivot the frame downward and release the latch knob.
Base
2. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not grip only the plastic
foot rails or drop the frame to the floor. Bend your legs and keep your back straight.
17
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call the telephone number listed on
he back cover of this manual.
t
PROBLEM: The power does not turn on
SOLUTION:
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
PROBLEM: The incline of the treadmill does not change correctly
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the back cover of this manual.
IMPORTANT: The treadmill is not
c
Tripped
Reset
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
he displays of the console do not function properly
PROBLEM:
SOLUTION:a.
T
Remove the key from the console and
THE POWER CORD.With the help of a second
person, carefully tip the Uprights (73, 78) down.
There may be two M4 x 16mm Screws (12) in the
bottom of the Belly Pan (69). If there are, remove
them. Note: A Phillips screwdriver with a shaft at
least 5 in. (13 cm) long is required. Then, raise the
Uprights.
UNPLUG
a
78
73
69
12
12
18
Remove the three M4 x 19mm Washer Head
Screws (13) and carefully pivot the Hood (53) off.
Locate the Reed Switch (54) and the Magnet (42)
on the left side of the Pulley (44). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If neces-
sary, loosen the M4 x 19mm Screw (1), move the
Reed Switch slightly, and then retighten the Screw.
Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a correct speed
reading.
Top
View
1/8 in.
54
13
53
1
42
44
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 16 to turn off the demo mode.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill perfor-
mance may decrease and the walking belt may be
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to 7
cm) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
insert the key, and run the treadmill for a few min
utes. Repeat until the walking belt is properly tight
ened.
If the walking belt still slows when walked on, see the back cover of this manual.
c.
-
-
-
b
2–3 in.
Rear Roller Bolts
19
PROBLEM: The walking belt is off-center or slips when walked on
OLUTION: a.I
S
PROBLEM: The crosswalk arms squeak during use
f the walking belt is off-center,first remove the
key and UNPLUG THE POWER CORD. If the
alking belt has shifted to the left,use the hex
w
key to turn the left rear roller bolt clockwise 1/2 of a
turn;
if the walking belt has shifted to the right,
turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
If the walking belt slips when walked on, first re-
b.
move the key and
Using the hex key, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side
of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt
centered. Then, plug in the power cord, insert the
key, and carefully walk on the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened.
UNPLUG THE POWER CORD.
a
b
SOLUTION: a. (Note: Correcting this problem requires a small
amount of white marine grease, available at hardware stores.) Turn the Resistance Knob (A) counterclockwise and remove it. Next, remove the
Resistance Cone (B) and the Crosswalk Arm (76 or
71), along with the Resistance Plate (C), Washers
(D), Spring Washer (E), Thrust Washers (F), and
Thrust Bearing (G). (Note: If the Resistance Plate
[C] comes out of the Resistance Cone [B], press it
back in.) Apply a thin layer of white marine grease
to the outer surface of the Resistance Cone (B).
Then, reattach all parts in the order shown at the
right.
B
76
F
E
A
C
G
D
20
EXERCISE GUIDELINES
WARNING: Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over the age of 35 or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is intended only as an exercise aid in determining
heart rate trends in general.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses
the first few minutes of exercise does your body begin
o use stored
t
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
carbohydrate calories
at calories
f
or energy. If your goal is to
f
for energy. Only after
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
WORKOUT GUIDELINES
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
Finish with 5 to 10 minutes of stretch-
21
PART LIST—Model No. 831.24723.7 R
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
Key No. Qty. Description Key No. Qty. Description
16 M4 x 19mm Screw
1
2 4 M4 x 25mm Screw
3 1 M4 x 13mm Lift Frame Screw
4 4 1/4" x 3 1/2" Bolt
5 4 M10 x 96mm Bolt
6 4 M8 x 25mm Bolt
7 1 3/8" Star Washer
8 8 M10 Star Washer
9 4 1/4" Washer
10 4 M8 Star Washer
11 5 M4 x 13mm Washer Head Screw
12 10 M4 x 16mm Screw
13 3 M4 x 19mm Washer Head Screw
14
15 2 M8 x 90mm Screw
16 1 Controller Ground Wire
17 2 M6 x 70mm Bolt
18 1 3/8" x 1 3/4" Bolt
19 1 3/8" x 1 1/2" Bolt
20 2 3/8" x 1" Bolt
21 1 M6 x 45mm Bolt
22 7 1/2" Screw
23 8 M5 x 25mm Screw
24 2 1/4" x 3/8" Bolt
25 2 3/8" x 3/4" Bolt
26 1 3/8" x 4" Bolt
27 2 M10 x 50mm Bolt
28 4 M4 x 13mm Screw
29 2 M6 Lock Washer
30 2 M6 Washer
31 3 3/8" Nut
32
33 4 M10 Nut
34 1 Motor Washer
35
36 2 3/8" Lock Nut
37 3 Hood Clip
38
39 1 Left Foot Rail
40 2 Walking Platform Cushion
41 2 Belt Guide
42
43 1 Motor Belt
44 1 Front Roller/Pulley
45 1 Walking Belt
46 1 Walking Platform
47 1 Right Foot Rail
48 1 Frame
49 1 Warning Decal
50 2 Rear Roller Bracket Plate
2 M8 x 35mm Screw
2
4
4 Cage Nut
1
3/8" Motor Nut
M8 Flange Nut
Magnet
1 1 Left Foot
5
52 1 Right Foot
53 1 Hood
54 1 Reed Switch
55 1 Reed Switch Clip
56 2 Frame Spacer
57 1 Lift Frame/Roller Ground Wire
58 1 Incline Motor
59 2 Rear Roller Bracket
60 1 Motor
61 1 Motor Bracket
62 3 Lift Frame Cable Tie
63 1 Lift Frame
64
65 1 Power Cord
66 1 Controller
67 1 Grommet
68 1 Reset/Off Circut Breaker
69 1 Belly Pan
70 1 Latch Insert
71 1 Left Crosswalk Arm
72 1 Latch Pin Assembly
73 1 Left Upright
74 2 Insert Screw
75 2 Crosswalk Arm Insert
76 1 Right Crosswalk Arm
77 1 Upright Wire
78 1 Right Upright
79 4 Bolt Spacer
80 1 Right Upright Spacer
81 4 Base Pad
82
83 1 Left Upright Spacer
84 2 Caution Decal
85
86 2 Wheel
87 1 Console
88
89 1 Left Handrail
90 1 Right Handrail
91 4 Handrail Endcap
92
93 1 Key/Clip
94 2 Releasable Tie
95 8 8" Cable Tie
96 2 Resistance Assembly
97 2 Handgrip
98 2 M10 x 30mm Screw
99 1 Lift Motor Spacer
100 1 Rear Roller
1 Filter Wire
2
1
1 Console Base
2
Base Endcap
Base
Cable Tie
0208A
22
Key No. Qty. Description Key No. Qty. Description
01 1 Hex Key
1
102 1 Lift Frame/Base Ground Wire
03 2 Frame Endcap
1
104 2 Base Pad Spacer
105 1 4mm Hex Key
106 1 5mm Hex Key
107 1 6mm Hex Key
108 3 15 1/2" Cable Tie
109 1 Incline Stop Bracket
* – 8" Blue Wire, 2F
*
* – 6" Blue Wire, M/F
*
* – 6" Black Wire, M/F
* – User’s Manual
*These parts are not illustrated.
Specifications are subject to change without notice.
If a part is missing, call 1-888-533-1333.
– 6" Blue Wire, 2F
– 6" Red Wire, M/F
23
98
44
14
46
45
42
43
98
14
23
23
35
41
39
23
23
15
22
40
17
50
30
30
50
17
100
22
15
35
51
52
1
1
23
23
35
28
1
47
23
40
1
23
41
35
48
28
49
29
29
59
59
105 106 107 101
103
103
EXPLODED DRAWING A—Model No. 831.24723.7 R
0208A
24
53
37
13
37
1
3
37
1
3
1
32
63
24
25
25
7
60
26
22
57
56
33
18
31
31
33
56
21
61
19
31
58
55
12
66
65
67
22
68
12
69
12
11
11
11
11
62
64
54
11
99
3
34
109
16
EXPLODED DRAWING B—Model No. 831.24723.7 R
0208A
25
6
10
70
73
6
10
72
4
9
8
5
83
82
6
10
6
10
20
36
4
9
20
36
81
2
5
8
78
82
80
81
2
81
2
27
86
33
85
81
2
33
86
27
79
79
77
77
84
84
74
71
8
75
8
97
96
74
8
75
76
97
96
22
102
104
104
EXPLODED DRAWING C—Model No. 831.24723.7 R
0208A
26
88
87
91
91
12
89
91
1
1
38
38
91
90
1
93
12
12
12
12
12
12
12
1
94
95
22
92
1
108
EXPLODED DRAWING D—Model No. 831.24723.7 R
0208A
27
Your Home
For repair—in your home—of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
®
(1-888-784-6427)
Get it fixed, at your home or ours!
® Registered Trademark /
TM
Trademark /
SM
Service Mark of Sears Brands, LLC
® Marca Registrada /
TM
Marca de Fábrica /
SM
Marca de Servicio de Sears Brands, LLC
90 DAY FULL WARRANTY
If this Sears Treadmill Exerciser fails due to a defect in material or workmanship within 90 days of the
date of purchase, call 1-800-4-MY-HOME®(1-800-469-4663) to arrange for free repair (or replacement if
repair proves impossible). The incline motor is warranted for 90 days from the date of purchase; the
drive motor is warranted for 5 years from the date of purchase.
This warranty does not apply when the Treadmill Exerciser is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
Part No. 259534 R0208A
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Printed in USA
© 2008 ICON IP, Inc.
Loading...