Page 1
Model No. 831.15629.0
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
• Assembly
• Adjustments
• Part List and Drawing
WEIGHT BENCH EXERCISER
User’s Manual
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manu
al for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL
60179
Page 2
TABLE OF CONTENTS
ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
W
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
A
ABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
C
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
FULL 90-DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly.
WARNING DECAL PLACEMENT
The decal shown here has been
placed on the weight bench. If the
decal is missing or illegible, please
call toll-free 1-888-533-1333, Monday
through Friday, 6 a.m. until 6 p.m.
Mountain Time, and order a free
replacement decal. Apply the decal
in the location shown.
2
Page 3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual and all
arnings on the weight bench before using
w
the weight bench. Use the weight bench only
as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
4. Keep the weight bench indoors, away from
moisture and dust. Place the weight bench
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
bench to mount, dismount, and use the
weight bench.
5. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
6. Keep hands and feet away from moving parts.
7. Keep children under 12 and pets away from
the weight bench at all times.
8. Always wear athletic shoes for foot protec-
tion while exercising.
10. Always make sure that the backrest knob is
ully inserted into the backrest frame before
f
exercising.
11. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys. Replace all
cables at least every two years.
12. Always set both barbell stops at the same
height.
13 Make sure that the set screws attaching the
barbell adapters are properly tightened each
time the adapters are used.
14. Always place an equal amount of weight on
each side of the weight carriage or barbell.
15. Always secure the weights with the weight
clips when they are mounted on the weight
carriage or barbell.
16. Always lower the weight carriage in a con-
trolled manner; never let the weight carriage
drop.
17. Always remove the lat bar when performing
an exercise that does not require the use of
the lat bar
.
9. The weight bench is designed to support a
maximum user weight of 300 pounds and a
maximum total weight of 610 pounds. Do not
place more than 310 pounds on the barbell.
Do not place more than 150 pounds on the
leg lever or the weight carriage. Note: The
weight bench does not include weights.
18. Always move your bench out of the way
when performing an exercise that does not
use the bench.
19. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Page 4
BEFORE YOU BEGIN
hank you for selecting the versatile PROFORM
T
300 weight bench. The weight bench is designed to
elp develop every major muscle group of the body.
h
Whether your goal is to tone your body, build dramatic
muscle size and strength, or improve your cardiovascular system, the weight bench will help you to
achieve the specific results you want.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
ASSEMBLED DIMENSIONS:
Height:
Width: 85 in. / 216 cm
Depth: 48 in. / 122 cm
85 in. / 216 cm
®
P
X
eading this manual, call 1-800-4-MY-HOME
r
(1-800-469-4663). To help us assist you, please note
he product model number and serial number before
t
calling. The model number is 831.15629.0. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
®
Lat Bar
Barbell
Locking Bar
Curl Pad
Seat
Curl Knob
Leg Lever
Right Side
Left Side
Backrest
Weight Carriage
Storage T
Barbell Stop
ube
Row Bar
Note: The terms “right side” and “left side” are determined relative to a person sitting on the
bench; they do not correspond to right and left on the drawings in the manual.
4
Page 5
ASSEMBLY
ake Things Easier for Yourself
M
Everything in this manual is designed to ensure
hat the weight bench can be assembled suc-
t
cessfully by anyone. Most people find that by
setting aside plenty of time, assembly will go
smoothly.
Before beginning assembly, carefully read the
following information and instructions:
Assembly requires two people.
•
• Make sure that there is enough clearance to walk
around the weight bench as you assemble it.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• Tighten all parts as you assemble them, unless
nstructed to do otherwise.
i
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The included Allen wrenches , and
the following tools (not included) may be
required for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Clear tape or masking tape, and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1.
Before beginning assembly, make sure you
understand the information in the box
above.
Make sure that the Left Seat Base (3) is oriented
as shown. Attach a Seat Base Bumper (31) to the
Left Seat Base with an M4 x 16mm Self-tapping
Screw (91) and an M4 Washer (84).
Attach a Bench Foot (15) to the Left Seat Base
(3) with two M4 x 16mm Self-tapping Screws (91)
and two M4 Washers (84).
Repeat this step with the Right Seat Base (2).
Make sure that the Right Seat Base is oriented
as shown.
1
2
3
15
31
84
91
84
91
5
Page 6
2. Attach the Bench Foot (15) to the Seat Base (1)
with two M4 x 16mm Self-tapping Screws (91)
nd two M4 Washers (84).
a
2
3. Insert two M10 x 100mm Screws (26) up through
the Base Plate (34), and the Seat Base (1), and
the Right and Left Seat Bases (2, 3).
Attach the Right and Left Seat Bases (2, 3) to the
Seat Base (1) with two M10 x 58mm Button Bolts
(95) and two M10 Nylon Locknuts (77).
34
1
3
77
15
84
84
91
3
2
95
1
26
4. Attach the Seat Frame (5) to the Seat Base (1)
with the indicated two M10 x 100mm Screws (26).
4
5
26
26
1
6
Page 7
5. Attach the Backrest (11) to the Backrest Frame
(8) with four M6 x 15mm Button Screws (17).
5
11
17
8
17
6. Grease the M10 x 87mm Button Bolt (94). Attach
the Backrest Frame (8) to the Seat Frame (5)
with the Bolt and an M10 Nylon Locknut (77). Do
not overtighten the Locknut; the Backrest
Frame must be able to pivot easily.
Engage the Backrest Frame (8) with the Backrest
Knob (22) and fully tighten the Knob into the Seat
Frame (5).
Attach the Seat Bumper (27) to the Seat Frame
7.
(5) with an M4 x 16mm Self-tapping Screw (91)
and an M4 Washer (84).
Grease an M10 x 82mm Button Bolt (93).
the Leg Lever (6) to the Seat Frame (5) with the
Bolt and an M10 Nylon Locknut (77). Do not
overtighten the Locknut; the Leg Lever must
be able to pivot easily
.
Attach
6
Grease
94
22
5
7
Grease
93
6
91
84
77
27
8
5
77
7
Page 8
8. Attach the Seat (12) to the Seat Frame (5) with
four M6 x 63mm Button Screws (92) and four M6
ashers (81).
W
8
2
1
5
81
9. Insert a Pad Tube (10) into the Leg Lever (6).
Slide two Foam Pads (14) onto the Pad Tube.
Assemble the other two Pad Tubes (10) to the
Leg Lever (6) and the Seat Frame (5) in the
same manner.
Attach the Curl Pad (13) to the Curl Post (7) with
10.
two M6 x 15mm Button
Screws (17).
9
10
14
92
14
6
10
92
5
10
14
10
14
13
7
17
8
Page 9
11. Attach the Left Rack Base (37) to the Center
Rack Base (39) with two M10 x 67mm Bolts (86),
n M10 Washer (80), and an M10 Nylon Locknut
a
Do not tighten the Bolts.
(77).
Repeat this step with the Right Rack Base (38).
11
86
12. Attach the Rear Rack Base (40) to the Rear
Upright (41) with two M10 x 67mm Bolts (86), two
M10 Washers (80), and an M10 Nylon Locknut
(77). Do not tighten the Bolts.
12
38
40
77
41
80
39
77
37
86
80
13. Attach the Foot Plate (49) and the Rear Rack
Base (40) to the Center Rack Base (39) with two
M10 x 63mm Button Bolts (90) and two M10
Nylon Locknuts (77).
Locknuts.
Attach the Foot Plate (49) to the Center Rack
Base (39) with an M10 x 63mm Button Bolt (90),
an M10 W
(77).
asher (80), and an M10 Nylon Locknut
Do not tighten the Locknut.
Do not tighten the
13
77
80
39
90
49
40
77
9
Page 10
14. Insert the M10 x 20mm Bolt (89) into the Weight
Carriage (42) from the side shown.
14
Slide the Weight Carriage Stop (58) onto the
ear Upright (41). Slide the Weight Carriage (42)
R
onto the Rear Upright.
15. Attach a Guide Rod (46) to the Left Rack Base
(37) with an M8 x 53mm Bolt (9), two M8
Washers (83), an 11mm x 8mm Spacer (82), and
an M8 Nylon Locknut (78).
Locknut.
Attach a Guide Rod (46) to the Right Rack
Base (38) in the same manner.
Do not tighten the
89
42
58
41
15
38
46
16. Attach a Barbell Stop Hook (48) to a Barbell Stop
(47) with an M10 x 25mm Bolt (88) and an M10
Nylon Locknut (77).
Locknut; the Stop Hook must be able to pivot
easily.
Slide a Bumper (4) and the Barbell Stop (47) onto
the right Guide Rod (46).
Identify the Right Barbell Guide (53) by the location of the screw hole. Slide the Barbell Guide
onto the right Guide Rod (46).
Repeat this step with the left Guide Rod (not
shown).
Do not overtighten the
16
Screw
Hole
48
77
4
53
47
37
46
9
83
83
88
82
78
10
46
Page 11
17. Attach a Front Upright (43) to the Right Rack
Base (38) with two M10 x 82mm Bolts (85), two
10 Washers (80), and an M10 Nylon Locknut
M
Do not tighten the Bolts.
(77).
Attach the Front Upright (43) to the right Guide
Rod (46) with an M10 x 25mm Bolts (88).
Repeat this step with the other Front Upright
(not shown).
17
88
46
43
18. Attach the Cross Frame (44) to the right Front
Upright (43) with two M10 x 82mm Bolts (85), two
M10 Washers (80), and an M10 Nylon Locknut
(77). Do not tighten the Bolts.
Repeat this step with the left Front Upright
(not shown).
19. Attach the Top Frame (45) to the Rear Upright
(41) with two M10 x 67mm Bolts (86), four M10
Washers (80), and two M10 Nylon Locknuts (77).
Do not tighten the Locknuts.
op Frame (45) to the Cross Frame
Attach the
(44) with two M10 x 78mm Bolts (87), two M10
Washers (80), and two M10 Nylon Locknuts (77).
Do not tighten the Locknuts.
T
18
19
85
85
80
43
87
80
80
44
45
86
77
38
44
77
77
80
80
80
41
11
80
77
Page 12
20. Orient the Locking Bar (50) as shown. Slide the
Barbell (51) through the Left Barbell Guide (52),
he Locking Bar, and the Right Barbell Guide (53).
t
Make sure that the Barbell is centered in the
arbell Guides. Engage the Locking Bar into the
B
Uprights (43) at the lowest position.
20
3
5
0
5
Hole
52
43
51
21. Handtighten an M8 x 20mm Button Screw (16)
into the Left Barbell Guide (52).
Slide a Weight Stop (69) onto the Barbell (51).
Handtighten an M6 x 15mm Button Screw (17)
into the Weight Stop. Make sure that the Screw
is tightened enough to engage the hole (see
drawing 20) in the Barbell.
Repeat this step on the other side of the
Barbell (51).
Tighten the screws used in this step, and the
bolts and locknuts used in steps 11–15 and
17–19.
Press two Center Base Feet (60) onto the Center
Rack Base (39). Press the Rear Upright Foot (59)
onto the Rear Upright (41). Press two Front
Upright Feet (64) onto the Front Uprights (43).
22. Route a Cable (61) up through the Top Frame
(45) and over a Pulley (63). Attach the Pulley
inside the Top Frame with an M10 x 67mm Bolt
(86), two M10 W
12.5mm Spacers (76), and an M10 Nylon Locknut
(77).
ashers (80), two 16mm x
21
22
77
60
76
61
80
52
43
76
63
80
64
16
45
86
51
41
17
59
39
60
69
23. Route the Cable (61) over a Pulley (63) and down
through the Top Frame (45). Attach the Pulley
inside the Top Frame with an M10 x 67mm Bolt
(86), two M10 Washers (80), two 16mm x
12.5mm Spacers (76), and an M10 Nylon Locknut
(77).
12
23
77
80
76
61
63
45
76
80
86
Page 13
24. Route the Cable (61) under a Pulley (63). Attach
the Pulley, a Cable Trap (66), and two Half Finger
uards (65) to the two Pulley Plates (35) with an
G
M10 x 50mm Bolt (79) and an M10 Nylon Locknut
ake sure that the Cable Trap is oriented
77). M
(
to hold the Cable in the groove of the Pulley.
24
77
5
6
35
66
61
63
65
79
35
25. Route the Cable (61) over a Pulley (63). Attach
the Pulley inside the Top Frame (45) with an M10
x 78mm Bolt (87) and an M10 Nylon Locknut
(77).
26. Attach the Cable (61) to the M10 x 20mm Bolt
(89) with an M10 Nylon Locknut (77). Make sure
that the Cable can pivot easily on the Bolt.
27. Route the second Cable (61) under a Pulley (63).
Attach the Pulley to the Center Rack Base (39)
with an M10 x 45mm Bolt (75) and an M10 Nylon
Locknut (77).
25
26
27
77
61
77
77
45
87
63
61
61
89
63
75
28. Route the Cable (61) over a Pulley (63). Attach
rap (66), and two Half Finger
the Pulley
Guards (65) to the two Pulley Plates (35) at the
indicated hole with an M10 x 50mm Bolt (79) and
an M10 Nylon Locknut (77). Make sure that the
Cable Trap is oriented to hold the Cable in the
groove of the Pulley.
, a Cable
T
13
28
77
65
39
35
65
79
66
63
61
Page 14
29. Attach the Cable (61) to the Rear Rack Base (40)
with an M10 x 67mm Bolt (86), two M10 Washers
80), and an M10 Nylon Locknut (77).
(
30. Make sure that all parts are properly tightened.
The use of the remaining parts will be explained
in ADJUSTMENTS starting below.
29
61
7
7
0
8
40
0
8
86
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 18 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ATTACHING THE CURL PAD
Remove the 56mm Round Cap (20) from the Seat
Frame (5). Secure the Curl Post (7) in the Seat
Frame with the Curl Knob (23).
Replace the 56mm Round Cap (20) into the Seat
Frame (5) when the Curl Pad (13) is not being used.
ADJUSTING THE BACKREST
Hold the top of the Backrest (11) with one hand and
pull out the Backrest Knob (22). Move the Backrest to
the desired position and reengage the Knob into the
Backrest Frame (8).
13
7
20
5
11
23
14
8
22
Page 15
ATTACHING ACCESSORIES
The Lat Bar (55) can be attached to a Cable (61) with
a Cable Clip (71). For some exercises the Chain (24)
should be attached between the Cable and the Lat
Bar with two Cable Clips.
6
71
1
he other accessories can be attached to the Cables
T
(61) in the same manner.
ATTACHING THE BARBELL ADAPTER
Slide the Barbell Adapter (54) onto the Barbell (51)
and secure it in place with an M8 x 10mm Set Screw
(62). Repeat this process on the other side of the
Barbell.
24
71
55
62
51
54
ADDING WEIGHT
Slide the desired amount of weight (not included)
onto the Weight Carriage (42). Secure the weight with
the Spring Clips (72).
Add weight to the Barbell (51) or Leg Lever (not
shown) in the same manner.
Weights can be stored on the Center Rack Base (39)
when they are not being used.
WARNING: Always place an equal
amount of weight on each side of the Weight
Carriage (42) or Barbell (51). Do not place more
than 150 pounds on the Weight Carriage or Leg
Lever (not shown). Do not place more than 310
pounds on the Barbell.
Weight
42
72
51
39
15
Page 16
ADJUSTING THE BARBELL STOPS
Hold the handle on the Barbell Stop Hook (48) and
disengage the Hook from the Front Upright (43).
Move the Barbell Stop (47) to the lowest point you
want the Barbell (51) to go during the exercise.
Reengage the Hook into the Upright. Repeat with the
ther Barbell Stop.
o
WARNING: Always set both
Barbell Stops (47) at the same height.
USING THE BARBELL
First, attach the desired amount of weight to the
Barbell (51) (see ADDING WEIGHT on the previous
page). Then, adjust the barbell stops (see ADJUSTING THE BARBELL STOPS above). Finally, lift the
Locking Bar (50) and disengage it from the Front
Uprights (43). When finished with the exercise, reengage the Locking Bar into the Uprights.
43
51
43
Handle
51
50
48
4
7
43
ADJUSTING THE CABLE
Woven cable, the type of cable used on your weight
rack, can stretch slightly when it is first used. Slack
can be removed from the Cable (61) by moving the
lower Pulley (63) closer to the upper Pulley.
Remove the M10 x 50mm Bolt (79) from the Pulley
(63), the two Pulley Plates (35), the two Half Finger
Guards (65), the Cable Trap (66), and the M10 Nylon
Locknut (77). Reattach the Pulley, Cable Trap, and
Finger Guards at a higher set of holes in the Pulley
Plates with the Bolt and Locknut.
63
79
35
65
65
77
66
63
61
16
Page 17
CABLE DIAGRAM
The cable diagram shows the proper routing of the
Cables (61). Use the diagrams to make sure that the
cables and the cable traps have been assembled correctly. If the cables have not been correctly routed,
he weight bench will not function properly and dam-
t
age may occur. The numbers show the correct route
for each cable. Make sure that the cable traps do
not touch or bind the cables.
2
1
2
4
3
1
5
3
17
Page 18
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
o increase the size and strength of your muscles,
T
push them close to their maximum capacity. Your muscles will adapt and grow as you progressively increase
the intensity of your exercise. You can adjust the intensity level of an individual exercise in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is right
for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of weight.
Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of weight and increase the number of repetitions in each set. Complete as many sets of 15 to 20
repetitions as possible without discomfort. Rest for 1
minute after each set. Work your muscles by completing more sets rather than by using high amounts of
weight.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross Training
Cross training is an ef
well-balanced fitness program. An example of a balanced program is:
Plan strength training workouts on Monday,
•
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an elliptical or
exercise bike, on
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of strength training and aerobic exercise will reshape and strengthen your body, plus develop your heart and lungs.
ficient way to get a complete and
uesday and Thursday.
T
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
s well as the number of repetitions or sets completed,
a
is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
-
18
Page 19
Rest for a short period of time after each set. The
O
P
Q
R
S
T
U
V
X
W
N
M
J
G
F
H
I
K
E
C
D
B
A
L
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
ideal resting periods are:
Rest for three minutes after each set for a muscle
•
building workout.
Rest for one minute after each set for a toning work-
•
out.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
ithout strain. Stretching at the end of each workout
w
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List the
date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to achieving the greatest results is to make exercise a regular
and enjoyable part of your everyday life.
19
Page 20
M8 Nylon Locknut (78)M10 Nylon Locknut (77)
M6 Washer (81)
M8 Washer (83)
M4 Washer (84)
M10 Washer (80)
M10 x 82mm Button Bolt (93)
M10 x 87mm Button Bolt (94)
M8 x 53mm Bolt (9)
M8 x 20mm Button Screw (16)
M8 x 10mm Set Screw (62)
M6 x 63mm Button Screw (92)
M6 x 15mm Button Screw (17)
M4 x 16mm Self-tapping Screw (91)
M10 x 50mm Bolt (79)
M10 x 45mm Bolt (75)
M10 x 82mm Bolt (85)
M10 x 78mm Bolt (87)
M10 x 67mm Bolt (86)
M10 x 20mm Bolt (89)
M10 x 25mm Bolt (88)
M10 x 63mm Button Bolt (90)
M10 x 58mm Button Bolt (95)
M10 x 100mm Screw (26)
PART IDENTIFICATION CHART
efer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
R
ing is the key number of the part, from the PART LIST in the center of this manual.
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached. If
a part is missing, call toll-free 1-888-533-1333.
Note: Some small parts
Page 21
PART LIST—Model No. 831.15629.0 R0905A
Key No. Qty. Description Key No. Qty. Description
1 1 Seat Base
2 1 Right Seat Base
3 1 Left Seat Base
4 2 Bumper
5 1 Seat Frame
6
7
8
9 2 M8 x 53mm Bolt
10 3 Pad Tube
11 1 Backrest
12 1 Seat
13 1 Curl Pad
14 6 Foam Pad
15 3 Bench Foot
16 2 M8 x 20mm Button Screw
17 8 M6 x 15mm Button Screw
18 1 Ankle Strap
19 2 50mm Round Cap
20 2 56mm Round Cap
21 1 Left Seat Cap
22 1 Backrest Knob
23 1 Curl Knob
24 1 Chain
25 6 19mm Round Cap
26 2 M10 x 100mm Screw
27 1 Seat Bumper
28 2 Backrest Frame Bushing
29 2 Leg Lever Bushing
30 1 48mm Thin Round Cap
31 2 Seat Base Bumper
32 1 Right Seat Cap
33 2 Locking Bar Bushing
34 1 Base Plate
35 2 Pulley Plate
36
37 1 Left Rack Base
38 1 Right Rack Base
39 1 Center Rack Base
40 1
41 1 Rear Upright
42 1 Weight Carriage
43 2 Front Upright
44 1 Cross Frame
45 1 Top Frame
46
47 2 Barbell Stop
48 2 Barbell Stop Hook
49
50 1
1 Leg Lever
1 Curl Post
1 Backrest Frame
1
2
1 Foot Plate
25mm x 50mm Cap
Rear Rack Base
Guide Rod
Locking Bar
51 1 Barbell
52 1 Left Barbell Guide
53 1 Right Barbell Guide
54 2 Barbell Adapter
55 1 Lat Bar
6 4 Handgrip
5
7 2 Weight Carriage Bushing
5
8 1 Weight Carriage Stop
5
59 1 Rear Upright Foot
60 2 Center Base Foot
61 2 Cable
62 2 M8 x 10mm Set Screw
63 6 Pulley
64 2 Front Upright Foot
65 4 Half Finger Guard
66 2 Cable Trap
67 8 Barbell Guide Bushing
68 4 Barbell Bushing
69 2 Weight Stop
70 6 48mm Round Inner Cap
71 2 Cable Clip
72 2 Spring Clip
73 1 Row Bar
74 1 50mm Square Inner Cap
75 1 M10 x 45mm Bolt
76 4 16mm x 12.5mm Spacer
77 28 M10 Nylon Locknut
78 2 M8 Nylon Locknut
79 2 M10 x 50mm Bolt
80 25 M10 Washer
81 4 M6 Washer
82 2 11mm x 8mm Spacer
83 4 M8 Washer
84 9 M4 Washer
85 8 M10 x 82mm Bolt
1
86
87 3 M10 x 78mm Bolt
88 4 M10 x 25mm Bolt
89 1 M10 x 20mm Bolt
90 3
91 13 M4 x 16mm Self-tapping Screw
92 4 M6 x 63mm Button Screw
93 1 M10 x 82mm Button Bolt
94 1 M10 x 87mm Button Bolt
95 2 M10 x 58mm Button Bolt
#
# 2 Allen Wrench
# 1 Grease Pack
#
1
1
1 Exercise Guide
M10 x 67mm Bolt
M10 x 63mm Button Bolt
s Manual
’
User
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
this manual for information about ordering replacement parts. If a part is missing, call toll-free 1-888-533-1333.
Page 22
7
3
56
56
21
32
5
12
23
20
20
27
22
15
15
31
31
15
1
10
14
25
25
14
10
14
25
25
14
10
14
25
25
14
6
19
19
29
30
3
2
8
11
28
28
36
17
17
7
13
17
94
91
93
77
77
81
92
92
81
84
91
84
91
84
91
77
84
91
26
34
84
84
91
84
91
95
55
56
5
6
71
52
68
68
69
67
67
16
33
50
51
53
5
4
68
68
69
67
67
70
62
17
16
33
17
54
70
62
18
24
EXPLODED DRAWING A—Model No. 831.15629.0 R0905A
Page 23
72
72
38
9
83
82
83
78
77
77
61
71
43
64
80
85
85
80
88
43
64
85
85
80
85
80
88
44
77
77
80
80
77
45
61
6
3
63
6
3
76
7
6
76
7
6
74
80
77
87
77
8
0
80
86
87
77
86
80
86
80
80
48
47
67
67
77
88
4
46
46
47
48
67
67
88
77
4
42
57
57
58
61
70
70
77
89
63
63
65
65
65
65
66
66
79
77
35
35
39
60
60
63
75
77
77
80
86
80
86
80
70
70
37
9
83
77
83
78
82
77
49
90
41
40
59
61
86
80
80
86
77
77
80
77
77
EXPLODED DRAWING B—Model No. 831.15629.0 R0905A
Page 24
FULL 90-DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States
and Sears will repair or replace the WEIGHT
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for
rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 60179
Part No. 230326 R0905A Printed in China © 2005 Sears, Roebuck and Co.
BENCH EXERCISER, free of charge.
Loading...