Profile PCD970R User Manual

INSTALLATION INSTRUCTIONS / OWNER S MANUAL

,

PCD970R

AM/FM HIGH POWER FLIP DOWN DETACHABLE FACE
CD PLAYER

INTRODUCTION

Congratulations on your purchase of a Profile state-of-the-art single disc CD player.
Your selection of a Profile car audio product indicates a true appreciation of fine musical
reproduction. Whether adding to an existing system or including your Profile CD player in
a new system, you are certain to notice immediate performance benefits.

FEATURES

50W x 4 Power Output
Flip Down Detachable Face

Remote Control
Dual RCA Line Output(Front & Rear)
Auxiliary RCA Line Input
Clock

30 Station Memory

4 Band Preset Equalizer
Loud Function

Power Level Meter
ISO/DIN Mounting
Blinking Security L.E.D.
Full Electronic Function Controls
Disc Scan, Random & Repeat Play

KEEP YOUR SALES RECEIPT

Take this time to attach your sales receipt to the manual and put in a safe place.
In case of any reason this product may need warranty service, your receipt will be
necessary to establish purchase date.

IMPORTANT! Before making any connections, disconnect the car s battery
until the installation is completed to avoid possible damage to the electrical
system.

,

Serial #

Purchase Date

1

SAFETY PRECAUTIONS

Secure the CD player

When installing your CD player in the vehicle, make sure it is mounted properly in the dash,
using an after market installation kit if needed. When using the supplied mounting sleeve,

it is a must that you also use the supplied back brace to support the back of the CD
player.

.

Use caution when mounting the CD player.

Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment
wires. Make sure you know where they are when mounting the CD player to avoid puncturing
lines, and shorting wires.

Use high grade wire connectors.

To ensure maximum power transfer and secure safe connections, it is recommended to use
high grade barrel or crimp cap connectors.

Do not run any wires underneath the vehicle.

Exposed wires can be cut or damaged. It is best to run all wires through the vehicle under the
carpet and/or side panels. This enables to a cleaner installation and less risk of damage.

Run signal wires away from electrical wires

To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or
engine noise), run signal wires away from the car's electrical wiring.

Make all ground wires as short as possible and terminated at the same point.

In order to reduce the chance of ground loops (i.e. engine noise), make the grounded wire as
short as possible to reduce the wire's resistance. Also, when using multiple components, make
sure all units are grounded at the same point.

Avoid sharp edges when running the wires.

To avoid the possibility of power, signal or speaker shorts, be careful not to allow the amplifier
wires to come in contact with sharp edges. Use a grommet to protect the wire when running
through the fire wall .

2

PCD970R

CARE AND MAINTENANCE

Cleaning the CD player

When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only
the exterior surface of the unit with a dry, clean soft towel using no chemical solvents.

Operating in extreme temperatures

Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case,
wait until the temperature in the vehicle is normal, then resume operation.

Protect your CDs.

When not using the disc player, it is recommended that you remove the CD.
Do not leave an ejected disc sitting on the edge of the disc player for long periods of time.
The disc will warp under direct sunlight. Always put each disc in its case to protect them
during times of non-use.

CD operation.

Never attempt to force anything other than a compact disc in the disc slot. This disc player
is a precision instrument that could be damaged by a foreign object.

Disc skip

When driving down a very rough road, the disc may skip. This will not scratch or damage the disc.

Removing and protecting detachable face plate.

The face plate of the unit may be removed as a theft deterrent. After removing the face
plate, use the case provided to keep the face plate from getting damaged.

PROTECTIVE CASE

FACE PLATE

( FIG.1)

OPEN BUTTON

FACE PLATE

( FIG.2)

Press the OPEN button to flip down the face plate (Fig 1). Then slightly push the face plate
towards the left side before pulling it out from the unit (Fig.2)
Store the face plate in the protective case provided for safe keeping (Fig.3).

3

DISC CARE AND PLAY:

Before playing, clean the disc with a clean, lint-free cloth.
Wipe the disc in the direction of the arrow.

Do not use solvents such as benzine or thinners. Commercially available
cleaners or anti static spray will damage the unit.

Insert a disc with the labeled surface up.

Label
surface up

Do not try to insert another disc when one has already been inserted.
Doing so may damage the unit.

Handle the disc by its edge to keep the disc clean and do not touch
the surface.

Do not stick paper or tape on the disc.

Do not expose the disc to direct sunlight which can cause the disc to warp.

Always store the disc in its case for protection. Scratched up discs will
produce poor sound performance and cause CD player to skip.

4

PCD970R

ELECTRICAL AND SIGNAL CONNECTIONS

Before making the following connections, take time to look over the vehicle's wiring and
determine the location and wires you will be connecting to. If you do not wish to cut or tap
into the vehicles existing factory wiring, there are wiring kits available at your car audio
retailer that will allow you to plug directly into the factory wiring harness. Make sure to
test all wires before connecting to the CD Player.

!

Connect Black wire to chassis ground.

!

Connect the Yellow memory backup wire to a Constant +12 Volt power source wire.

!

Connect the Red ignition wire to a switched +12 Volt power source wire. (The power

wire that is energized when the key is in the accessory position).

!

The blue wire is connected only if a power antenna or an amplifier is used in the
system. This wire supplies +12 Volt output when the CD Player is turned on,
which activates most power antenna relays or amplifier turn on circuits.

FOUR SPEAKER SYSTEM

ANTENNA CONNECTOR

R CH RED

L CH WHITE

MEMORY +12V

AUX RCA INPUT

R

BROWN

L

+

-

BATTERY
+12V

FRONT LEFT
SPEAKER

BLACK(GND)

RED (B+)

SWITCHED +12V
(ON WITH IGNITION)

BLUE AUTO ANTENNA

REAR LEFT
SPEAKER

YELLOW

++

++

15A Fuse

FILTER

BOX

0.5A Fuse

0.5 A
FUSE

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

Low level signal output for
connection to amplifier or
signal processors.

FRONT RCA OUTPUT

BLACK

REAR RCA OUTPUT

GRAY

GRAY

GRAY/BLACK

VIOLET

VIOLET/BLACK

R

L

R

L

++

++

R CH RED

L CH WHITE

R CH RED

L CH WHITE

FRONT RIGHT
SPEAKER

REAR RIGHT
SPEAKER

5

R CH RED

L CH WHITE

MEMORY +12V

AUX RCA INPUT

R

BROWN

L

YELLOW

-

BLACK(GND)

+

BATTERY
+12V

RED (B+)

SWITCHED +12V
(ON WITH IGNITION)

BLUE AUTO ANTENNA

FRONT LEFT
SPEAKER

TWO SPEAKER SYSTEM

15A Fuse

FILTER

BOX

0.5A Fuse

0.5 A

++

FUSE

WHITE

WHITE/BLACK

NOT USED

NOT USED

ANTENNA CONNECTOR

Low level signal output for
connection to amplifier or
signal processors.

FRONT RCA OUTPUT

BLACK

REAR RCA OUTPUT

GRAY

GRAY

GRAY/BLACK

NOT USED

NOT USED

R

L

R

L

++

R CH RED

L CH WHITE

R CH RED

L CH WHITE

FRONT RIGHT
SPEAKER

CAUTION! Tape unused wires so they do not short against other wires or
chassis ground.

6

PCD970R

MOUNTING THE CD PLAYER

There are two different ways to mount the CD Player. In most Japanese vehicles you can
use the factory mounting brackets, taking advantage of the ISO/DIN opening. If your vehicle
does not have ISO/DIN opening, you can mount the CD Player using the supplied DIN sleeve
and rear support bracket. When considering your mounting location, make sure the unit will
be leveled. If you cannot mount the CD Player level, due to your vehicles design, make sure
there is no more than a 30 degree tilt. Keeping this in mind will assure proper CD play and
overall reliability.

DIN SLEEVE MOUNTING

Insert the mounting sleeve into a
standard DIN cutout in the dash
kit, dashboard or Console.

Bend the mounting tabs of the sleeve
with a screwdriver to secure the bracket
firmly in place.

7

Insert the CD Player in the
mounting sleeve until it locks.

Attach the back brace to the CD

player using the supplied hardware.

Then attach the other end of the

brace to a firm mounting surface

(i.e. Dash brace, fire wall, e.t.c.)

This will brace the back of the CD

player to ensure solid mounting to

prevent theft and provide optimal

CD play.

Once the CD player is secured, fit the trim
ring over outside edge of the radio until it
snaps into place.

To Attach the Face Plate:

Basically, the face plate should be attached
to the unit in the reverse order of removal.
1 Hold the right side of the plate with the
plate facing down.
First attach the left side of the plate to the
unit by inserting the hole into the left holder.
2 Then slightly push the plate to the left
before attaching the right side hole into the
right holder.
3 Finally push up the face plate until click sound is heard.

8

PCD970R

ISO/DIN MOUNTING

If you own a Japanese vehicle, you can use the standard ISO/DIN mounting screw holes on
the side of the CD player to attach to the existing factory mounting bracket, without using
the provided DIN sleeve.

!

Remove the factory ISO/DIN mounting bracket from the car along with the factory radio.

!

Remove the factory radio from the bracket by unscrewing the two Phillips screws on each

side of the radio paying close attention to their screw positions and saving the screws to

mount the CD player.

!

Remove the two spring clips from each side of the CD player by removing the screws.

These clips are not used in ISO/DIN mounting method and must be removed to expose the

ISO/DIN mounting holes.

!

Also remove the detachable face and rectangular trim ring from the CD player and mount
the CD player to the factory ISO/DIN bracket using the screws that you removed from
the factory radio.

Connect the wire harness and antenna plug to the back of the CD player. Then mount the

!

factory ISO-DIN bracket to the car.

Note: It is not necessary to attach the outer rectangular trim ring for ISO/DIN mounting
method.

REMOVING THE CD PLAYER

!

To remove the CD player from an ISO/DIN mount, follow the above mounting procedure
in reverse order.

!

To remove the CD player from a sleeve mount, use the pair of keys provided.

Remove the rectangular trim ring by
applying pressure with your finger
tips, then gently pull out away from
the dash.

PLACE FINGER TIPS HERE

Insert the provided removal key into the opening on each side of the CD player.
Push the keys inward until they snap in place. Firmly grab the keys and slowly
pull the CD player out away from the dash.

9

LOCATION AND FUNCTION OF CONTROLS

10

PCD970R

1 POWER
To turn ON the unit, press any button except the OPEN button.
To turn OFF the unit, press the PWR button for more than 2 seconds.

2 FLIP DOWN PANEL
Press the OPEN button to flip down the face plate. This will allow you to insert
or eject a CD and also remove the face plate.

3 CD PLAY
To play a CD, press the OPEN button to flip down the face plate exposing the CD
inserting slot. Gently insert the CD into the slot with the label side facing up. The
disc will automatically be loaded into the unit and start playing the first track of
the disc. The digital display will indicate the track number.

4 EJECT CD
To remove a CD once inserted, press the OPEN button to flip down the face plate
and press the ( ) button located on the left hand side of the CD inserting slot.
Once the CD is ejected, the unit switches to radio mode.

5 VOLUME UP/DOWN
Rotate the VOL knob in clockwise direction to raise the system s volume
and in counter clockwise direction to lower the system s volume.

Note: For remote control, press the button to raise the volume and press
the button to lower the volume.

6 MODE
Press the MOD button to change among tuner (radio), CD (if disc is loaded),
and auxiliary input playing mode.

Radio CD AUX.

7 BAND
Under radio mode press the BND button to change between three FM bands and
two AM bands.

FM 1 FM 2 F M 3 AM 1 AM 2

-

+

,

,

11

8 9 RADIO TUNE & CD TRACK UP/DOWN, CD FAST FORWARD/REWIND

I

Under radio mode, press the 8 or 9 button momentarily and repeatedly to

I

change the frequency number up or down one step. Under SEEK 1 mode, press and
hold the 8 or 9 button for more than 2 seconds to seek to the next or previous

I

clear station. Under SEEK 2 mode, press and hold the 8 or 9 button to speedily

I

I

I

change stations up or down. Changing stations will stop once the button is released.
(Please refer to SEEK on page 13 on how to set the seek mode between SEEK 1
and SEEK 2.)

In CD play mode, press the 8 or 9 button to move to the next or previous track.

I

In CD play mode, press and hold the 8 or 9 button to fast forward or fast

I

I

I

reverse through the song. The CD resumes playing when the button is released.

10 PRESET STATIONS
There are 6 numbered buttons to store into memory and recall stations for each
band. Select a band (if needed) as explained in 7 . Tune to a radio station that
you wish to store. Select, press, and hold a preset numbered button for 2 seconds
until you hear a beep indicating that the station has been stored in memory. To
recall a preset station, simply push the numbered preset button.

11 FUNCTION SELECT
SEL button allows you to display different functions for adjustments. Press the
SEL button momentarily and repeatedly to move the display from Volume, Bass,
Treble, Balance, and Fader functions. Use the VOL knob 5 to adjust the selected
mode. When the mode has not been adjusted for several seconds, display and mode
returns to normal radio or CD operation.

VOL BAS TRE BAL FAD
(Volume) (Bass) (Treble) (Balance) (Fader)

VOLUME - Press the SEL button once. Adjust the volume level using the VOL knob
5 .

BASS - Press the SEL button twice. Adjust the bass level using the VOL knob 5 .

TREBLE - Press the SEL button three times. Adjust the treble level using the VOL
knob 5 .

BALANCE - Press the SEL button four times. Adjust the sound balance between
left and right speakers using the VOL knob 5 .

FADER - Press the SEL button five times. Adjust the sound balance between front
and rear speakers using the VOL knob 5 .

12

PCD970R

Press the SEL button for more than 2 seconds to display additional set of functions
for adjustments, such as DSP, Beep On/Off, Seek 1 or 2 , Clock 12 or24, and
Volume Last/Adjust.

DSP - The unit is equipped with 4 preset equalization modes. Press the SEL button
for more than 2 seconds to display DSP OFF. Then turn in
the clockwise direction to choose one of 4 following preset EQ s in the

the VOL knob 5

,

following order.
When using preset EQ modes you will not have access to Bass and Treble
settings.

DSP OFF

FLAT CLASSIC ROCK POP

BEEP - The beep sound when you press a button on the unit can be turned on or
off. Press the SEL button for more than 2 seconds to display the DSP
function. Press the SEL button again momentarily to display BEEP ON/OFF.
Then use to turn on/off the beep sound.

the VOL knob 5

SEEK- The unit is equipped with two types of seeks, SEEK 1 and SEEK 2, for radio
stations. Press the SEL button for more than 2 seconds to display the DSP
function. Press the SEL button twice momentarily to display SEEK 1 or 2.
Then use the VOL knob 5 to switch between SEEK 1 and SEEK 2. (This
adjustment is only available during radio operation)

SEEK 1 mode: Pressing 8 or 9 button for more than 2 seconds will seek

I

I

up or down to the next strong station during radio operation.
SEEK 2 mode: Pressing 8 or 9 button continuously will speedily change

I

I

station up or down until the button is released.

CLOCK- The unit is equipped with two types of clock formats, 12 hour and 24 hour.
Press the SEL button for more than 2 seconds to display the DSP function.
Press the SEL button three times momentarily to display CLOCK 12 or 24.
Then use the VOL knob 5 to choose between 12 and 24 .

SET VOL - A certain volume level can be set to come on when the unit is turned
on or can be set to come on at the same last level before the unit was
turned off. Press the SEL button for more than 2 seconds to display
the DSP function. Press the SEL button four times momentarily to
display VOL LAST/ADJ. Use the VOL knob 5 to choose between
VOL LAST and VOL ADJ. To set the volume to a certain level, press the
SEL button momentarily when VOL ADJ is displayed. Then use the VOL
knob 5 to adjust to certain volume level when A-VOL is displayed.

13

12 CD TOP/PAUSE
In CD play mode, press the TOP 12 button to pause CD play. Press again to
resume normal play.

In CD play mode, press the TOP 12 button for more than 2 seconds to go back
to the top of the disc and play the first track.

13 CD SCAN
In CD play mode, press the INT 13 button to turn on intro playing first 10 seconds
of each track. When wish to listen to the whole track during intro mode,
press the button again to turn off intro.

14 REPEAT PLAY
In CD play mode, press the RPT 14 button to continuously playing the current
track. Press it again to cancel the repeat feature.

15 RANDOM PLAY
In CD play mode, press the RDM 15 button to play all tracks of the disc in random
sequence. Press it again to cancel random play.

16 AUTOMATIC STORING & PRESET SCANNING
In radio mode, press and hold the APS 16 button for more than 2 seconds to
activate the automatic storing function. Once activated, the radio starts search­ ing for first 6 strong signaled stations and stores them into the preset memory.
After completion, the radio will tune back to the first preset memory station.

In radio mode, press the APS 16 button for momentarily to activate the preset
scanning function. Once activated, the radio starts scanning all preset memory
stations for few seconds at a time while the preset memory number flashes on
the LCD. Pressing the button again will stop the scan.

17 MUTE
Press the MU button to silence the system. Press a second time to resume
listening.

18 LOUDNESS
Press the LOUD button once to enhance the bass effect.
Press again to cancel the loudness effect.

19 MONO/STEREO
Monaural (Mono) or Stereo mode can be selected for FM tuner s reception. For
best quality sound, stereo mode should be selected. However, Mono mode can be
selected to help the reception of distant radio stations. Press the ST button to
select between Mono and Stereo modes.

14

,

PCD970R

20 CLOCK
Press the CLK button to display the time on the LCD for 5 seconds. To adjust the
time, press and hold the CLK button until the hour flashes and use the VOL 5
knob to adjust the hour. Press and hold the CLK button again until the minute
flashes and use the VOL 5 knob to adjust the minute.

21 RADIO SCAN (Only from Remote)
Pressing the SCN button from the remote control, the unit will scan and search
for the next strong station while playing each station for 5 seconds with station
number flashing. Pressing the SCN button again will stop the radio scan.

22 LOCAL/DX
This button is used to control the sensitivity of the FM radio tuner while searching
for a station. When the radio is powered on, the local mode is off by default. Press
the LOC button to turn on the local mode only to receive the strongest stations.

23 INFRARED REMOTE CONTROL SENSOR

24 SECURITY LED
Designed as a theft deterrent, the red LED will flash when the unit is turned off
and face plate removed.

25 RESET
The reset button should be pressed when installation is complete and also when
all buttons do not operate.

15

MAINTENANCE OF REMOTE CONTROL

Before using the remote control, the insulating patch must be removed. This
patch was installed to insulate the battery from draining until ready to use.

BATTERY INFORMATION:

Lithium Battery: CR2025 3V
Battery Life: Approximately 6 months.

Replacing the Battery from the Remote Control:

1) Turn over the remote control so the rear side of the remote is facing up.

2) Remove the battery holder by pressing the locking tab with your thumb
and pulling it out.

3) Replace the battery with the same type and the + side facing up.

4) Gently push in the holder until securely locked into place.

WARNING:

Do not recharge, disassemble or dispose of in fire.

Battery leakage may cause damage to the unit.

To avoid the risk of accident, keep batteries out of reach of children.

16

PCD970R

TROUBLE SHOOTING THE SYSTEM

The following chart will help in solving most problems that may occur. Should any problem
persist after you have made these checks, please consult your nearest Profile retailer.
Before going through this check list, refer back to the wiring and operating procedures.

ERROR CODES

E 1~ E 10 The unit cannot be operated because of trouble. Press t

button . If the indicator still appears after pressing the "RESET"

25

25

button , your unit needs repair. Please refer to the warranty section
of this manual for details on getting the unit serviced.

.

SYMPTOM CAUSE SOLUTION

25

25

No Power

Disc cannot

be loaded or

ejected.

No sound.

The function

buttons do

not work.

New installation.
The vehicle's ignition switch

is not on.

The fuse is blown. Replace the fuse with another fuse of the

There is a disc already in

the player.

You are trying to put the

compact disc in upside down.

The compact disc is

extremely dirty or

defective.

The temperature in the car

is too hot.

Condensation build-up on the

inside of the unit.

The volume control is all the

way down.

The speakers are bad. Test the speakers to determine if they need

The built-in microprocessor

is operating incorrectly.

Press the RESET button.

Turn the ignition switch to the accessory

position. If there is still no power, check the

fuses at the vehicle's fuse block or the

radio's fuse leads.

same recommended value

Remove the disc in the player, then put in

the new one.

Insert the compact disc with the label facing

up.

Clean the compact disc with a compact disc

cleaning solution or replace the defective

compact disc.

Cool the inside of the vehicle, then try again.

Leave the disc player off and turn the

vehicle's air conditioner on to remove the

condensation build-up inside the unit.
Adjust the volume control.

replacing.
Remove the disc, then re-insert it. Press the

reset button .

he "RESET"

17

SYMPTOM CAUSE SOLUTION

The compact

disc skips.

The installation angle is

greater than 30 degrees

Adjust the angle of the unit to less than 30

degrees

The radio

does not

work. The

Radio station

automatic

selection

does not

work.

The disc player is installed

incorrectly

The compact disc is

extremely dirty or defective

disc.
Condensation build-up on the

inside of the unit.

The antenna is not

connected or the antenna is

bad.

The signals in your listening

area are weak.

Check to see if the unit is fastened securely

with the back brace supporting the rear of

the unit.

Clean the compact disc with a compact disc

cleaning solution or replace the defective

compact disc.
Leave the disc player off and turn the

vehicle's air conditioner on to remove the

condensation build-up inside the unit.

Check the antenna and connection to insure

proper performance.

Select stations manually and make sure the

tuner is in the distant stereo mode.

18

PCD970R

SPECIFICATIONS

GENERAL

Power Supply Requirements...........................................DC 12 Volts, Negative Ground

Chassis Dimensions ...............................................................7 (W) x 6 1/2 (D) x 2 (H)

||||

||||

||||

Tone Controls...........................................................................................................................

Bass @ 100Hz..........................................................................................+10dB / -10 dB

Treble @ 10Khz.......................................................................................+10dB / -10 dB

Equalizer..................................................................................................................4 Presets

Maximum Output Power.........................................................................................50W x 4

RMS Output Power..................................................................................................30W x 4

Maximum Current Consumption........................................................................15 Ampere

Fuses

Memory (Constant)........................................................................................15 Ampere

Accessory (Switched).................................................................................0.5 Ampere

RCA line out voltage.....................................................................................................3.7 V

CD PLAYER

Signal to Noise Ratio...................................................................................................>85dB

Channel Separation......................................................................................................>80dB

Frequency Response........................................................................................5Hz ~ 20Khz

Usable Disc....................................................................................CD/CD-R/CD-RW Discs

RADIO

FM

Frequency Coverage.....................................................................87.5 to 107.9MHz(US)

IF................................................................................................................................10.7MHz

Station Presets...................................................................................................................18

AM

Frequency Coverage........................................................................530 to 1710KHz(US)

IF.................................................................................................................................450KHz

Station Presets...................................................................................................................12

Due to continuing product improvement, specifications subject to change without notice.

19

Profile Consumer Electronics, Inc. warrants this product to be free from defects in
material and workmanship for a period of One (1) Year from the date of sale to the
original consumer purchaser. If this product is proven to be defective within this one
year period, Profile will repair it when said product is returned, with a copy of the
dated sales receipt, freight prepaid to Profile.

This warranty is valid only in the United States. This warranty does not cover any
expense incurred in the removal and/or re-installation of this product. This warranty
does not cover any Profile product damaged by accident, misuse, abuse, improper line
voltage, fire, water, lightning, or other acts of God. This warranty is void if any parts
and/or service is/are furnished by anyone other than Profile. This warranty is void if
the factory applied serial number is altered or removed from the product.

This warranty does not cover cartons, cases, batteries, broken or marred cabinets,
magnetic tapes, or any other accessories used in connection with this product or
consequential damages due to a defect in the product.

LIMITED WARRANTY

Any implied warranties, including fitness for use and merchantability, are limited in
duration to the period of the express warranty set forth above. No person is
authorized to assume for Profile any other liability in connection with the sale of the
product. Profile expressly disclaims liability for incidental and consequential
damages that might be caused by this product. The remedies provided under this
warranty are exclusive and lieu of all others.

This warranty gives you specific legal rights. You may have other rights which vary
from state to state or province to province. Some states or provinces do not allow
limitation on how long warranties last, so the above may not apply to you. Additionally,
some states/provinces do not allow the exclusion to limitation of consequential or
incidental damages, so the above limitation or exclusion may not apply to you.

* In the space below, record the serial number that is located on the back of the unit
along with the purchase date and location.

Model Number __________________

Serial Number

____________________

Purchase Date __________________ Where Purchased _________________

RETAIN YOUR SALES RECEIPT ALONG WITH THIS CARD. IT IS YOUR ONLY
VALID DOCUMENT TO RECEIVE WARRANTY SERVICE.

WARRANTY REPAIR POLICY

In the unlikely event of product failure, the following procedures
should be followed

1) The unit must be under the 1-year warranty period.

2) The unit must have no physical damage.

3) A copy of the original proof of purchase must be sent with the unit.

4) Include a brief description of the problem or failure with the unit.

5) Include the return street address and daytime telephone number.

6) Allow 2~3 weeks for repair (this period includes shipping time).

Send unit to: PROFILE CONSUMER ELECTRONICS, INC.

Note: All units failing to meet the above requirements will be

subject to a charge and or may not be repaired.

15060 SHOEMAKER AVE
SANTA FE SPRINGS, CA 90670
TEL: [phone]

PROFILE CONSUMER ELECTRONICS, INC.

15060 SHOEMAKER AVE

SANTA FE SPRINGS, CA 90670

TEL: [phone] FAX: [phone]

WWW.PROFILEUSA.COM