Profile CD7200 User Manual

INSTALLATION INSTRUCTIONS / OWNER S MANUAL

,

CD7200

AM/FM HIGH POWER DETACHABLE FACE
CD PLAYER

INTRODUCTION

Congratulations on your purchase of a Profile state-of-the-art single disc CD
player. Your selection of a Profile car audio product indicates a true appreciation
of fine musical reproduction. Whether adding to an existing system or including
your Profile CD player in a new system, you are certain to notice immediate
performance benefits.

FEATURES

35W x 4 Power Output Power Level Meter
Dual RCA Line Output(Front & Rear) ISO/DIN Mounting
Clock Blinking Security L.E.D.
30 Station Memory Full Electronic Function Controls
4 Band Preset Equalizer Disc Scan, Random & Repeat Play

KEEP YOUR SALES RECEIPT

Take this time to attach your sales receipt to the manual and put in a safe place.
In case of any reason this product may need warranty service, your receipt will
be necessary to establish purchase date.

IMPORTANT! Before making any connections, disconnect the car s battery
until the installation is completed to avoid possible damage to the electrical
system.

Serial #

Purchase Date

1

,

SAFETY PRECAUTIONS

Secure the CD player

When installing your CD player in the vehicle, make sure it is mounted properly in the dash,
using an after market installation kit if needed. When using the supplied mounting sleeve,

it is a must that you also use the supplied back brace to support the back of the CD
player.

.

Use caution when mounting the CD player.

Remember there are many electrical wires, vacuum lines, brake lines and air bag deployment
wires. Make sure you know where they are when mounting the CD player to avoid puncturing
lines, and shorting wires.

Use high grade wire connectors.

To ensure maximum power transfer and secure safe connections, it is recommended to use
high grade barrel or crimp cap connectors.

Do not run any wires underneath the vehicle.

Exposed wires can be cut or damaged. It is best to run all wires through the vehicle under the
carpet and/or side panels. This enables to a cleaner installation and less risk of damage.

.

Run signal wires away from electrical wires

To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or
engine noise), run signal wires away from the car's electrical wiring.

Make all ground wires as short as possible and terminated at the same point.

In order to reduce the chance of ground loops (i.e. engine noise), make the grounded wire as
short as possible to reduce the wire's resistance. Also, when using multiple components, make
sure all units are grounded at the same point.

Avoid sharp edges when running the wires.

To avoid the possibility of power, signal or speaker shorts, be careful not to allow the amplifier
wires to come in contact with sharp edges. Use a grommet to protect the wire when running
through the fire wall .

2

CD7200

CARE AND MAINTENANCE

Cleaning the CD player

When cleaning the vehicle, be sure not to get any water in or on the CD player. Clean only the
exterior surface of the unit with a dry, clean soft towel using no chemical solvents.

.

Operating in extreme temperatures

Sometimes the unit will not operate in extreme, hot or cold temperatures. If this is the case,
wait until the temperature in the vehicle is normal, then resume operation.

Protect your CDs.

When not using the disc player, it is recommended that you remove the CD.
Do not leave an
ejected disc sitting on the edge of the disc player for long periods of time.
The disc will warp
under direct sunlight. Always put each disc in its case to protect them during times of non-use.

CD operation.

Never attempt to force anything other than a compact disc in the disc slot. This disc player is
a precision instrument that could be damaged by a foreign object.

Disc skip

When driving down a very rough road, the disc may skip. This will not scratch or damage the disc.

.

Removing and protecting detachable front panel.

The front panel of the radio may be removed as a theft deterrent. After removing the front
panel, use the case provided to keep the front panel from getting damaged.

Press the OPEN button to detach the front panel, then take the front panel away
from the head unit(fig.1) and put it in the protective case (fig.2) for safe keeping.

3

DISC CARE AND PLAY:

Before playing, clean the disc with a clean, lint-free cloth.
Wipe the disc in the direction of the arrow.

Do not use solvents such as benzine or thinners. Commercially available
cleaners or anti static spray will damage the unit.

Insert a disc with the labeled surface up.

Label
surface up

Do not try to insert another disc when one has already been inserted.
Doing so may damage the unit.

Handle the disc by its edge to keep the disc clean and do not touch
the surface.

Do not stick paper or tape on the disc.

Do not expose the disc to direct sunlight which can cause the disc to warp.

Always store the disc in its case for protection. Scratched up discs will
produce poor sound performance and cause CD player to skip.

4

CD7200

ELECTRICAL AND SIGNAL CONNECTIONS

Before making the following connections, take time to look over the vehicle s wiring and

,

determine the location and wires you will be connecting to. If you do not wish to cut or tap into
the vehicles existing factory wiring, there are wiring kits available at your car audio retailer
that will allow you to plug directly into the factory wiring harness. Make sure to test all wires
before connecting to the CD Player.

!

Connect Black wire to chassis ground.

!

Connect the Yellow memory backup wire to a Constant +12 Volt power source wire.

!

Connect the Red ignition wire to a switched +12 Volt power source wire. (The power

wire that is energized when the key is in the accessory position).

!

The blue wire is connected only if a power antenna or an amplifier is used in the
system. This wire supplies +12 Volt output when the CD Player is turned on,
which activates most power antenna relays or amplifier turn on circuits.

FOUR SPEAKER SYSTEM

ANTENNA CONNECTOR

Low level signal output for

MEMORY +12V

+

-

BATTERY
+12V

RED (B+)

SWITCHED +12V
(ON WITH IGNITION)

BLUE AUTO ANTENNA

FRONT LEFT
SPEAKER

REAR LEFT
SPEAKER

YELLOW

BLACK(GND)

++

++

10A Fuse

FILTER

BOX

0.5A Fuse

0.5 A
FUSE

WHITE

WHITE/BLACK

GREEN

GREEN/BLACK

connection to amplifier or
signal processors.

FRONT RCA OUTPUT

BLACK

REAR RCA OUTPUT

GRAY

GRAY

GRAY/BLACK

VIOLET

VIOLET/BLACK

++

R

R CH RED

L

L CH WHITE

R

R CH RED

L

L CH WHITE

++

FRONT RIGHT
SPEAKER

REAR RIGHT
SPEAKER

5