Professional Series PS72001 User Manual

Beverage Center

User Manual

Model: PS72001

English

IMPORTANT SAFEGUARDS

When using this appliance, always exercise basic safety precautions, including the following:

1) Read all of the instructions before using this appliance.

2) Use this appliance only for its intended purpose as described in this use and care guide.

3) This entertainment center must be properly installed in accordance with the installation instructions before it is used. See grounding instructions in the installation section.

4) Never unplug your entertainment center by pulling on the power cord. Always grasp the plug firmly and pull straight out from the outlet.

5) Repair or replace immediately, all electric service cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length, the plug or the connector end.

6) Unplug your entertainment center before cleaning or before making any repairs. Note: If for any reason this product requires service, we strongly recommend that a certified technician performs the service.

7) If your old entertainment center is not being used, we recommend that you remove the doors and leave the shelves in place. This will reduce the possibility of danger to children.

8) This entertainment center should not be recessed or built-in in an enclosed cabinet. It is designed for freestanding installation only.

9) Do not operate your entertainment center in the presence of explosive fumes.

10) Your entertainment center was NOT designed to store perishable foods.

Store only bottled or canned beverages.

SAVE THESE INSTRUCTIONS

DANGER

Risk of child entrapment. Before you throw away your old

appliance, take off the doors. Leave the shelves in place so

that children may not easily climb inside.

Table Of Contents

PAGE

IMPORTANT SAFEGUARDS 1

PARTS AND FEATURES 3

INSTALLING YOUR ENTERTAINMENT CENTER 4-5

Unpacking your Entertainment Center 4 Leveling your Entertainment Center 4 Proper Air Circulation 4 Electrical Requirements 4 Use of Extension Cords 4 Installation Limitations 5 Door Reversal 5

ENTERTAINMENT CENTER FEATURES AND USE 6 General Features 6 Adjustable Temperature Dial 6 Entertainment Center Interior Shelves 6 Using the lock 6

PROPER ENTERTAINMENT CENTER CARE AND CLEANING 7 Cleaning and Maintenance 7 Defrosting 7 Power Interruptions 7 Vacation & Moving Care 7 Normal Operating Sounds 8

English

TROUBLESHOOTING 8

English

Knowing Your Entertainment Center

Parts and Features

1. Thermostat Dial (location varies by model)

2. Coated Storage Shelves (style and quantity vary by model)

3. See-through Glass Door

4. Leveling Legs

5. Recessed Door Handle

6. Work Top (Not on all models)

7. Dual Dispense Can Storage (On some models only)

8. Flip Shelf (Not on all models)

9. Lock with Key (Not on all models)

English

Installing Your Entertainment Center

Unpacking your Entertainment Center

1. Remove all packaging material. This includes the base and all adhesive tape holding the entertainment center accessories inside and outside.

2. Inspect and remove any remains of packing, tape or printed materials before powering on the entertainment center.

Leveling your Entertainment Center

• Your entertainment center has 2 leveling legs which are located at the

bottom front corners of your entertainment center. After properly placing your entertainment center in its final position, you can level your entertainment center.

• Leveling legs can be adjusted by turning them counterclockwise to raise your

entertainment center or by turning them clockwise to lower your entertainment center. The entertainment center door will close easier when the leveling legs are extended.

Proper Air Circulation

• To ensure that your entertainment center works at the maximum efficiency it

was designed for, you should install it in a location where there is proper air circulation and electrical connections.

• The following are recommended clearances around the entertainment center:

Sides……………3/4 “(19mm)

Top....................2” (50mm)

Back..................2” (50mm)

Electrical Requirement

• Make sure there is a suitable power Outlet (115 volts, 15 amps outlet) with

proper grounding to power the entertainment center.

• Avoid the use of three plug adapters or cutting off the third grounding in

order to accommodate a two plug outlet. This is a dangerous practice since it provides no effective grounding for the entertainment center and may result in shock hazard.

Use of Extension Cords

• Avoid the use of an extension cord because of potential safety hazards under

certain conditions. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot outlet that will accept the plug. The marked rating of the extension cord must be equal to or greater than the electrical rating of the appliance.

English

Installation Limitations

• Do not install your entertainment center in any location not properly insulated or heated e.g. garage etc. Your entertainment center was not designed to operate in temperature settings below 55˚ Fahrenheit.

• Select a suitable location for the entertainment center on a hard, even surface away from direct sunlight or heat source, e.g. radiators, baseboard heaters, cooking appliances etc. Any oor unevenness should be corrected with the leveling legs located at the bottom.

Door Reversal Instructions

Your entertainment center is built with a reversible door. You have the choice of either opening it from the left or the right side. In order to reserve the opening direction of your door, please follow these simple instructions. Tilt the entertainment center backwards. Secure the rear from sliding. Tape the door to the cabinet to prevent from falling.

1. Remove the 3 hexagonal screws from base bracket.

2. Remove the pivot holding the bottom of the door.

3. Separate the door from the cabinet and remove the pivot axle from the upper

side of the door. Remove and reinstall upper and lower axle door inserts to opposite side.

4. Install the pivot axle to the opposite side.

5. Re-attach the door to the cabinet and secure with tape.

6. Attach the base bracket to the opposite side

7. Install the bottom pivot aligning with the lower pivot insert on the door. Attach

the 3 hexagonal screws to base bracket.

8. Remove tape.

9. As the unit was tilted, wait 24 hours before plugging it in.

+ 13 hidden pages