1
GP-3500/3600/3700 Series
Installation Guide
Package Contents
(1) GP Unit (1)
(2) English and Japanese installation
Guides (1 of each) <This Guide>
(3) Warning/Caution Information (1)
(4) Installation Gasket (1, attached to the
GP unit)
(5) Installation Fasteners (Set of 4)
(2 sets of 4 for AGP-3750T only)
(6) RCA-BNC Convertor (1)
(Only for AGP-3550T, AGP-3560T,
AGP-3650T/U, AGP-3750T)
(7) AUX Connector
(1, Attached to the GP unit)
(8) Power Connector (1)
(Attached to the G P unit for DC type)
(9) USB Cable Clamp (2 port) (1 set)
(Holder: 1, Cover: 2)
This unit has been carefully packed, with
special attention to qualit y. However,
should you find anything damaged or
missing, please contact your local GP
distributor immediately.
About the Manual
For the detailed information on GP3000
series, refer to the following manuals.
• GP3000 Series Hardware Manual
• Maintenance/Troubleshooting
The manuals can be selected from the
help menu of GP-Pro EX or downloaded
from Pro-face Home Page.
URL
http://www.pro-face.com/otasuke/
About Revision
The nameplate on the GP has the
revision number of the GP. In the
example below, the asterisk, which is
placed at the “5” position, shows that the
revision number is “5”.
Caution
Be sure to read the “Warning/Caution
Information” on the attached sheet
before using the product.
2
Part Names and Functions
Name Description
AStatus LED
B Ex p ans i o n U n i t I n t erf a c e ( E X T ) Used to connect an expan sion unit tha t can tran smit dat a.
C Ethernet Interface (LAN)
10BASE-T/100BASE-TX
This interface uses an RJ-45 type modular jack
connector (8 pins).
D USB Host Interface (USB)
2 ports
Complies with USB 1.1. Uses a “TYPE-A” connector.
Power supply voltage:5 VDC
±5%,
Output current:500mA(max.)
The maximum communication distance: 5m
E Expansion Unit Interface
*1
Used to connect an expansion unit that can transmit
data.
Front Left Side Rear
Bottom
(With CF Card Cover open)
AGP-3650T
AGP-3650T AGP-3650T
AGP-35*0T
A
B
C
F
G
H
E
D
I
JK
M
N
O
L
P
Color Indicator
Operation Mode
(Drawing)
Logic execution mode
(when logic is enabled)
Green
ON
OFFLINE
-
In operation RUN
Flashing
In operation STOP
Red
ON When power is turned on.
Flashing
In operation Major Error
Orange
ON Backlight burnout or GP malfuction
*1
*1 Please see GP3000 Series H ardware Manual "Replacing
the Backlight" for the details.
Flashing
During software startup
3
F VM Unit Interface
*1
The interface which connects the VM unit
manufactured by Digital Electronics Corporation.
(This interface is available only in units with embedded
color LCD TFT display.)
G
Auxiliary input/output /
Voice Output Interface (AUX)
This interface is External Reset, Alarm Output,
Buzzer Output, and sound output.
H
Expansion Memory Interface
Cover
Remove the cover to add more memory.
I CF Card Access LED
Lit in green when the CF Card is inserted and the cover
is closed, or when the CF Card is being accessed.
• Do not remove or insert the CF Card when the LED
lamp is on. Doing so may damage data on the CF
Card.
J Power Connector
DC model: Power Socket Connector
AC model: Power Input Terminal Block
KCF Card Cover
-
L
AUDIO Input Interface
(L-IN/MIC)
It’s an interface to whic h a microphone is connected. A
mini jack connector (∅3.5 mm) is used. (Supported by
AGP-3550T, AGP-3560T, AGP-3650T/U, AGP-3750T
only)
M
VIDEO Input Interface
(V-IN)
It’s an interface to which a video camera is connected.
NTSC (59.9 Hz) and PAL (50 Hz) are supported. A
RCA connector (75Ω) is used. (Supported by AGP3550T, AGP-3560T, AGP-3650T/U, AGP-3750T only)
N Serial Interface (COM1)
D-Sub 9-pin plug type. RS232C, RS422, and RS485
are switched by software.
O Serial Interface (COM2)
D-Sub 9-pin socket type. RS422 and RS485 are
supported.
P Dip Switches Located inside the CF Card Cover.
*1 The Expansion Unit Interface 1 and VM Unit Interface cannot be used simultaneously with AGP-
3500T/3550T/3560T.
4
General Specifications
Electrical Specifications
DC Model AC Model
Power Supply
Input Voltage DC 24V AC 100 to 240 V
Rated Voltage DC 19.2 to 28.8 V AC 85 to 265 V
Allowable V oltage
Drop
10 ms (max.)
1 cycle or less (Voltage drop interval
must be 1s or more.)
Power Consumption
AGP-3500L
AGP-3500S
DC 24 V 2.08 A or less
(TYP 1.08 A)
AC 100 V 0.90 A or less
(TYP 0.45 A)
AC 240 V 0.45 A or less
(TYP 0.26 A)
AGP-3500T
AGP-3510T
AGP-3550T
AGP-3560T
DC 24 V 2.08 A or less
(TYP 1.22 A)
AC 100 V 0.90 A or less
(TYP 0.58 A)
AC 240 V 0.45 A or less
(TYP 0.29 A)
AGP-3600T
AGP-3650T
• When GP Rev.5 is NOT
marked
*1
DC 24 V 2.08 A or less
(TYP 1.30 A)
• When GP Rev .5 is ma rked
*1
DC 24 V 2.08 A or less
(TYP 1.0 A)
*1 For details on how to check the revision, See "About Revision" (page 1)
• When GP Rev.5 is NOT
marked
*1
AC 100 V 0.90 A or less
(TYP 0.55 A)
AC240 V 0.45A or less
(TYP 0.30A)
• When GP Rev.5 is marked
*1
AC 100 V 0.90 A or less
(TYP 0.40 A)
AC240 V 0.45A or less
(TYP 0.23A)
AGP-3600U
AGP-3650U
DC 24 V 2.08 A or less
(TYP 1.50 A)
AC 100 V 0.90 A or less
(TYP 0.55 A)
AC240 V 0.45A or less
(TYP 0.30A)
GP-3700
Series
50 W or less
AC 100 V 1.1 A or less
(TYP0.75 A)
AC 240 V 0.7 A or less
(TYP0.44 A)
In-Rush Current 30 A (max.) 60 A (max.)
Voltage Endurance
AC 1000 V 2 0 mA for
1 minute (between charging and
FG terminals)
AC 1500 V 20 mA for
1 minute (bet we en ch argin g an d
FG terminals)
Insulation Resistance DC 500 V 10 MΩ (min.) (between charging and FG terminals)
5
Environmental Specifications
Structural Specifications
Physical
Surrounding Air
Temperature
0 to 50 °C
*1
*1 When using STN Colo r L CD m odel i n a n en viro nment w her e the tem peratu re b ecome s or e xceeds
40 °C for an extended period of time, the screen contrast level may decrease from its original level
of brightness .
Storage Temperature -20 to +60 °C
Ambient Humidity
10 to 90 % RH (Wet bulb temperature: 39 °C max. - no
condensation.)
Storage Humidity
10 to 90 % RH (Wet bulb temperature: 39 °C max. - no
condensation.)
Dust 0.1 mg/m
3
and below (non-conductive levels)
Pollution Degree For use in Pollution Degree 2 environment.
GP-35/36/3700 Series
except AGP-36*0U
AGP-36*0U
Installation
Grounding
Grounding resistance of 100Ω, 2mm
2
or thicker wire, or your
country’s applicable st andard.(Same for FG and SG terminals)
Structure
*1
*1 The front face of the GP unit, installed in a solid panel, has been tested using conditions equivalent to
the standards shown in the specification. Even though the GP unit’s level of resistance is equivalent to
these standards, oils that should have no effect on the GP can possibly harm the unit. This can occur in
areas where either vaporized oils are present, or where low viscosity cutting oils are allowed to adhere
to the unit for long periods of time. If the GP’s front face protection sheet becomes peeled off, these
conditions can lead to the ingress of oil into the GP and separate protection measures are suggested.
Also, if non-approved oils are present, it may cause deformation or corrosion of the front panel’s plastic
cover. Therefore, prior to installing the GP be sure to confirm the type of conditions that will be present
in the GP’s operating environment.
If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from
the panel, the original level of the protection cannot be guaranteed. To maintain the original protection
level, be sure to replace the installation gasket regularly.
Rating: Equivalent to IP65f
NEMA #250 TYPE 4X/13
(Front surface at panel embedding)
Feature size: All-in-one
Installation configuration: Panel
embedding
Rating: IP65f
(Front surface at p anel em bedding)
Feature size: All-in-one
Installation configuration: Panel
embedding
Cooling Method Natural air circulation
Loading...