Page 1
BIZ1Aseries
Safety and Regulatory Information
Notice for the USA
FCC Part 15: This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, this notice is not a guarantee that interference
will not occur in a particular installation.
CAUTION: To comply with the limits for the class B device, pursuant
to Part 15 of the FCC Rules, this device must be installed in computer
equipment certified to comply with the Class B limits.
All cables used to connect the computer and peripherals must be shielded and
grounded. Operation with non-certified computers or non-shielded cables
may result in interference to radio or television reception.
Any changes or modifications not expressly approved by the grantee of
this device could void the user’ s authority to operate the device.
COPYRIGHT: This publication, including all photographs, illustrations
and software, is protected under international copyright laws, with all rights
reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without the express written consent of the manufacturer.
DISCLAIMER: The information in this document is subject to change
without notice. The manufacture makes no representations or warranties with
respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose.
~0~
Page 2
BIZ1Aseries
TABLE OF CONTENTS
CH1. MOTHERBOARD FEATURE ..................................................... 2
1.1 ABOUT THE MANUAL ...................................................... 2
1.2 SPECIFICATIONS............................................................. 3
1.3
COLOR CODING FOR PC99 CONNECTORS................. 5
1.4 POWER OFF CONTROL SOFTWARE ............................ 6
1.5 PACKING CHECK LIST .................................................... 7
CH2. SETUP GUIDE............................................................................ 8
2.1 MOTHERBOARD LAYOUT............................................... 8
2.2 CONNECTOR & JUMPER REFERENCE CHART ........... 9
2.3 THE SETUP STEPS........................................................ 10
2.3-1 JUMPER & CONNECTOR SETTING ................... 10
2.3-2 MEMORY INSTALLATION.................................... 26
2.3-3 HOW TO INSTALL THE CPU ............................... 29
2.3-4 INSTALLING THE MOTHERBOARD.................... 33
2.3-5 INSTALLING THE INTERFACE CARD ................ 33
2.3-6 INSTALLING ACCESSORY CABLES .................. 34
CH3. AWARD BIOS SETUP ............................................................. 37
3.1 THE MAIN MENU............................................................ 39
3.2 STANDARD CMOS SETUP............................................ 41
3.3 BIOS FEATURES SETUP............................................... 43
3.4 CHIPSET FEATURES SETUP........................................ 48
3.5 POWER MANAGEMENT ................................................ 51
3.6 PNP / PCI CONFIGURATION SETUP............................ 56
3.7 INTEGRATED PERIPHERALS ....................................... 58
3.8 SUPERVISOR PASSWORD & USER PASSWORD ...... 61
3.9 IDE HDD AUTO DETECTION OPTION.......................... 61
3.10 SAVE AND EXIT SETUP OPTION ............................... 62
3.11 EXIT WITHOUT SAVING OPTION ............................... 62
CH4. SOFTWARE SETUP ................................................................ 63
4.1 INSTALLING THE IDE BUS MASTER DRIVER ............. 63
4.2 THE TEMPERATURE SENSOR - W8378ID .................. 65
~1~
Page 3
BIZ1Aseries
Chapter 1
Motherboard Feature Introduction
Congratulations on purchasing your Pro-Motherboard – BIZ1Aseries.
The BIZ1A
function position and provide your system with stable performance.
The BIZ1A
170mm and uses a 4-layer printed circuit board. This board features a SLOT
1 processor socket. This socket can be installed with the new generation of
Intel the PentiumII processors.
The BIZ1A
that permits the use of inexpensive 66 MHz memory chips or highperformance 100 MHz memory chips. Two DIMM sockets are provided, for
a maximum memory capacity of 256 MB. It is also ready for PC99 – the
color-coding of connectors. By the way, when you setup up your PC will be
no confused and obvious. The motherboard has the Intel chipset supports an
AGP graphics card. Four PCI slots and two ISA slots are provided for system
expansion. An anti-virus function is built-in in the BIOS component. This
protects the system from boot viruses and ensures that a clean environment is
maintained at all times. This is a powerful platform that leverages the low-
series motherboard will increase your computer system into a full-
series motherboard is an ATX board measuring 304mm by
series motherboard supports a system bus of 66 and 100 MHz
cost/high-performance features of the new generation Intel ZX chipsets. You
will be able to feel for yourself how convenient it is when you use it.
1.1 ABOUT THE MANUAL
The manual consist of the following chapters:
CH1. Motherboard feature introduction – Introduce the features of
BIZ1A
package.
series and the checklist of items that are shipped with the
~2~
Page 4
BIZ1Aseries
CH2. Setup guide – Let you learn how to install the motherboard and get
your system up and running.
CH3. Award BIOS setup – Configure the BIOS of motherboard for optimum
performance.
CH4. Software setup – Let you learn how to install the software drivers and
support programs that are provided with this motherboard.
1.2 SPECIFICATIONS
System Chipset
Processor
Bus Architecture
Clock Generator
DRAM Modules
BIOS
Intel 82440ZX PCIset (82443ZX + 82371EB) w/AGP
solution
Single Slot 1 support
Intel Pentium
Intel Pentium
Intel Celeron processor at 266-366Mhz
AGP/PCI/ISA
66.8, 68.5, 75, 83.3, 100, *103, *112, and *133Mhz
( * For your reference only )
168 pin DIMMs x 2.
Support 8MB to 256MB SDRAM.
2MB Award PnP BIOS with enhanced ACPI feature for
PC98 compliance.
Supports 120MB ATAPI floppy disk.
Supports ZIP disk drive.
Supports multi-boot from IDE,SCSI,CD-ROM and FDD.
Supports software clock control.
Supports Trend ™ ChipAway AntiVirus.
Supports HDD S.M.A.R.T.
®
II processor 233Mhz ~ 450Mhz.
®
III processor 450Mhz ~ 550Mhz.
~3~
Page 5
BIZ1Aseries
1 Floppy port (up to 2.88MB, 3 mode floppy supported &
LS-120).
On Board I/O
On Board IDE
Port
Expansion slot
PC99 connectors
I/O Chip
Other Feature
2 Serial ports, 1 Parallel port (SPP/EPP/ECP).
2 USB, 1 PS/2 mouse, 1 PS/2 keyboard.
1 IrDA.
Dual Ultra DMA/33 IDE ports support greater than 8.4GB
HDD.
ATAPI IDE CD-ROM & LS-120.
1 x 32-bit AGP slot.
4 x 32-bit PCI slots.
2 x 16-bit ISA slots.
Ready for PC99 color connectors
Winbond super I/O W83977TF-AW.
Supports keyboard & mouse power on feature with ATX
power.
Onboard Creative
CPU & power supply temperature header. (Optional)
Wake-up On LAN header.
®
SB-Link header.
Board Size
ATX form factor
Size : 304mm x 170mm (12" x 6.7")
~4~
Page 6
BIZ1Aseries
1.3 COLOR CODING FOR PC99 CONNECTORS
The color scheme is a careful balance of a number of criteria aimed at
making the PC easier for the consumer to understand and set up. The colorcoding of connectors has proven to be an effective tactic in helping end users
associate the peripheral connector with its mate on either the CPU or monitor.
It is expected that standard industry icons and possibly the physical shape of
the connector overloads themselves can also contribute to the "obviousness"
of a first-time set up.
PC99 Connector Guidelines
The following are the primary criteria established by the design team to
make the selection of the colors:
1. PCs are often set up in low light conditions. Therefore, use vibrant
colors wherever possible.
2. About 4% of people have some level of red/green color blindness.
Avoid using red and green together in situations where shape, size, or
labeling can be confused.
3. With older age, the eye's cornea may yellow. For this reason, similar
connectors should use colors that are different in ways other than their
yellow content.
4. Color selection should be considerate of cultural, social, and
psychological meaning. In some cases, related industries have
established a certain level of standardization of color coding (for
example, red/white/yellow in consumer electronics) that should also
be considered when making the final selection.
5. Colors should be easily discernable when used on small labels on the
backside of a CPU.
6. Try not to duplicate colors, even if connectors are obviously different,
for the sake of communication in user assistance collateral or phone
support calls.
7. Be sensitive to the overall impression of a personal computer and its
aesthetic intentions. Realize these colors will be used on PCs with
housings that could range in color value from almost white to black.
~5~
Page 7
BIZ1Aseries
,
PC99 color connector definition
Connector Color Panton
Analog VGA Blue 661C
Audio line in Light blue 284C
Audio line out Lime 577C
Digital monitor White
IEEE 1394 Grey 424C
Microphone Pink 701C
MIDI/Gameport Gold 131C
Parallel Burgundy 235C
PS/2-compatible keyboardPurple 2715C
PS/2-compatible mouse Green 3395C
Serial Teal or Turquoise 322C
Speaker out/subwoofer Orange 157C
Right-to-left speaker Brown 4645C
USB Black 426C
Video out Yellow 123C
SCSI, network, telephone
modem, and so on
None
1.4 POWER OFF CONTROL SOFTWARE
The motherboard design supports the software power off Control feature
through the SMI code in the BIOS under Win98/95 operating system
environment. It is an ATX form factor, so you should use ATX power
supply.
First, connect the power switch cable (provided by the ATX/AT case
Supplier) to the connector [ PS_BT ] on the motherboard (Please refer to the
following illustration). In the BIOS screen of “POWER MANAGEMENT
SETUP”, choose “User Defined”(or min power saving or Max power saving)
in “POWER MANAGEMENT” and choose “Yes” in “PM Control by APM”.
~6~
Page 8
BIZ1Aseries
Note: BIOS Setup. Please refer the “Chapter 3 Award BIOS Setup”
PS_BT
In Windows 98/95, under the “SHUT DOWN” option, the computer’s
power will switch off automatically and put the PC in a suspend mode. A
blinking power light will indicate this. To restart the system, simply press the
Power Button.
1.5 PACKAGING CHECK LIST
The Motherboard comes securely packed in a gift box and shipping carton.
If any of the above items are missing or damaged, please contact your
supplier.
The motherboard contains:
Q’ TY Description
1 Motherboard : With Intel ZX chipset
1 Driver : CD-Title w/Installation label
• PC-Cillin Software
• Motherboard Bus master Driver
• W83781D Temperature sensor Driver
1 Resister : For Temperature Sensor (Optional)
1 Cable
1 Cable : Floppy Cable
1 User’ s guide : PC-Cillin
1 Manual
: IDE Cable
: User’ s manual
~7~
Page 9
BIZ1Aseries
Chapter 2
Setup Guide
2.1 Motherboard layout
~8~
Page 10
BIZ1Aseries
2.2 Connector & Jumper Reference Chart
T : Mouse
B : K/B
USB 1/2
T : LPT1
B : COM1
COM2
(Optional)
SUPER
I/O
ATX POWER
Connector
SLOT1
DIMM1
ˆˇ
DIMM2
3V
Battery
˄
˄
FAN1
FAN3
˄
BIOS
Connector Front View
MS
LPT
KB
USB
~9~
COM1
COM2
J 3
P
Page 11
BIZ1Aseries
2.3 The setup steps
Please refer to the following steps to setup your computer:
I. Refer to the Jumper Setup section to set up the jumpers correctly.
II. Install the DIMM modules on the motherboard; be sure to set up
safely.
III. Install the CPU on the motherboard (please refer to the CPU
installation manual).
IV. Choose a case and install the motherboard into this case.
V. Plug in all the interface cards of your system equipment.
VI. Connect the cable, power supply and other message lines in the
correct position.
VII. Turn on the power and set up your computer system software.
VIII. Reboot, and enter the Award BIOS setup Menu to correct the
definitions.
2.3-1 Jumper & Connector Setting
PS1- PS/2 Keyboard Connector
This connector can connect PS/2 Keyboard and has better
performance.
Pin Description Pin Description
1 Keyboard Data 2,6 N.C.
3 Ground 4 +5V
5 Keyboard Clock
DIMM2
DIMM1
˄
˄
3V
Batt ery
SLOT 1
BIOS
SUP ER
I /O
ˆˇ
ATX PO WER
Connect or
˄
~10~
Page 12
BIZ1Aseries
PS2- PS/2 Mouse Connector
This connector can connect PS/2 Mouse and has better performance.
Pin Description Pin Description
1 Mouse Data 2,6 N.C.
3 Ground 4 +5V
5 Mouse Clock
DIMM2
DIMM1
˄
˄
3V
Batt ery
SLOT 1
ˆˇ
ATX PO WER
Connect or
˄
BIOS
SUP ER
I/O
J16 - ATX Power Supply Connector
This connector allows the motherboard to draw the power form ATX
power supply. It requires an ATX power supply of 250 watt at least.
Pin Description Pin Description
1,2,11 + 3.3 V 3,5,7,13,1
Ground
5,16,17
4,6,19,20 + 5 V 8 POWER GOOD
9 5VSB 10 +12 V
12 -12 V 14 PS-ON
18 - 5 V
ˆˇ
ATX POWER
Connector
˄
˄
˄
3V
Batter y
DIMM2
DIMM1
SLOT1
BIOS
SUPER
I/O
~11~
Page 13
BIZ1Aseries
LPT1 - Printer Connector
This Connector can transfer the data to printer for printing on paper.
Pin Signal Name Pin Signal Name
1 Strobe- 14 AFD
2 Data Bit 0 15 Error
3 Data Bit 1 16 INIT
4 Data Bit 2 17 SLCTIN
5 Data Bit 3 18 GND
6 Data Bit 4 19 GND
7 Data Bit 5 20 GND
8 Data Bit 6 21 GND
9 Data Bit 7 22 GND
10 ACK 23 GND
11 Busy 24 GND
12 PE 25 GND
13 SLCT 26 GND
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
BIOS
SUPER
I/O
ˆˇ
ATX POWER
Con nector
˄
~12~
Page 14
BIZ1Aseries
COM1,COM2 –Serial Connectors
type connector for transferring data between computer and devices.
Pin Signal Name Pin Signal Name
These connectors allow mouse or the other device which use this
1 DCD 6 DSR
2 SIN 7 RTS
3 SOUT 8 CTS
4 DTR 9 RI
5 GND 10 NC
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
ˆˇ
ATX POWER
Connector
˄
BIOS
SUPER
I/O
J14 - Universal Serial Bus (USB1, USB2) Connectors
These connectors allow the device which use this type connector
for transferring information between computer and devices.
USB1 Pin Signal Name USB2 Pin Signal Name
1 USB VCC 0 1 USB VCC 1
2 USB Data - 2 USB Data -
3 USB Data + 3 USB Data +
4 USB GND 0 4 USB GND 1
5 GND 5 GND
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
BIOS
SUPER
I/O
ˆˇ
ATX POWER
Conn ector
˄
~13~
Page 15
BIZ1Aseries
SB LINK – For Sideband Signals Connector
PCI Sound Card. Ex. Creative SB-LINK Connector
This connector is as a bridge between the motherboard and Creative's
Pin Signal Name Pin Signal Name
1 GNT#A 2 GND
3 ------ 4 REQ#A
5 GND 6 GPI7
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
SUPER
I/O
ˆˇ
ATX POWER
Conn ector
˄
J15 - Infrared Connector: IR
This connector is used to connect IR Device.
Pin Signal Name
1
2
3
4
VCC
NC
SIRRX
GND
BIOS
5
IRTX
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
ˆˇ
ATX POWER
Conn ector
˄
~14~
BIOS
SUPER
I/O
Page 16
BIZ1Aseries
WOL – Wake-up On LAN Connector
Interface Card ) which gives WOL function to the motherboard. Enable
this function for remotely managing PC on a network. When a PC
receives the wake up command during sleep, the LAN controller will
wake up the PC.
Pin Signal Name
This connector is used to connect an add-in NIC ( Network
1
2
3
5VSB
GND
LID
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
ˆˇ
ATX POWER
Conn ector
˄
BIOS
SUPER
I/O
JP4 – Keyboard & PS/2 Mouse ON NOW Connector
This connector is used to enable keyboard & PS/2 mouse power
on with hot keys or mouse button.
Pin Signal Name
1-2
2-3
Disable
Enable
ˆˇ
ATX POWER
˄
Connector
˄
˄
3V
Batter y
DIMM2
DIMM1
SLOT1
~15~
BIOS
SUPER
I/O
Page 17
BIZ1Aseries
JP2 – CMOS Clear
This jumper is able to clear the current data stored in the CMOS
memory.
JP2 Description
1-2 Normal (default)
2-3 Clear CMOS
DIMM2
DIMM1
˄
˄
3V
Battery
SLOT1
ˆˇ
AT X P O W E R
Conne ctor
˄
BIOS
SUPER
I/O
JP1 – POWER BUTTON
This connector is used to control your system power.
Pin Description
1 5V Stand-by
3 Power Button
DIMM2
DIMM1
˄
˄
3V
Battery
ˆˇ
˄
SLOT1
ATX PO W E R
Conne ctor
BIOS
SUPER
I/O
~16~
Page 18
BIZ1Aseries
OTHER JUMPER SETTING
Locate the bank of switch and indicator connectors. These connectors
provide control functions to your system case. Such as Speaker, HD LED,
Power LED, Key Lock, SMI Switch, SMI ED and Reset … etc. Please use
the cable below to make the connections.
Qpxfs`MFE LFZ`Mpdl
TQL
Q3 Q33
Q2
Sftfu
IEE`MFE
ˆˇ
ATX POWER
Connec tor
TNJ
˄
˄
˄
3V
Battery
DIMM2
DIMM1
SLOT1
SUPER
I/O
TNJ`MFE
BIOS
Q32
Pin Name Description
1 - 3 Reset Reset buttom
7 - 9 HDD_LED Hard Disk LED
13 - 15 SMI Suspend mode
19 - 21 SMI_LED Suspend LED
2 - 6 Power_LED Power LED
8 – 10 KEY_ Lock Key Lock
14 – 20 SPK Speaker
~17~
Page 19
BIZ1Aseries
FAN2
FAN1, FAN2, FAN3 - FAN CONNECTORS
These connectors allow the fans of CPU and AGP to draw the power
from the motherboard.
FAN1 FAN3
GND
Fan In
Fan Out
ˆˇ
ATX POWER
Connector
GND
˄
DIMM2
DIMM1
Fan In
˄
˄
3V
Battery
SLOT1
Fan Out
SUPER
I/O
Fan In
GND
BIOS
FAN1 : CPU FAN CONNECTOR.
FAN2 : For SYSTEM COOL FAN CONNECTOR.
FAN3 : For SYSTEM COOL FAN CONNECTOR.
Fan Out
~18~
Page 20
BIZ1Aseries
CPU TYPE SELECT
The Intel Pentium
frequency, one is 66 MHz and the other is 100 MHz. But not all
!
Pentium
®
II CPU have two kinds of external frequency. Please
refer your CPU specifications to set the BUS speed firstly.
CPU Bus Speed – 66 MHz Part:
1. 233MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Open Open Short Short Short
®
II processor has two kinds of external (Bus)
2. 266MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Short Short Open Short Short
ATX POWER
Connector
SUPER
I/O
BIOS
ATX POWER
Connector
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
SLO T1
˄
˄
3V
Battery
ˆˇ
˄
DIMM1
DIMM2
˄
˄
3V
Battery
1
23456
1
SUPER
I/O
BIOS
~19~
Page 21
BIZ1Aseries
3. 300MHz
4. 333MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Open Short Open Short Short
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Short Open Open Short Short
5. 366MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Open Open Open Short Short
ATX POWER
Connector
SUPER
I/O
BIOS
ATX POWER
Connector
ˆˇ
23456
˄
DIMM1
DIMM2
SLOT 1
SLO T1
˄
˄
3V
Battery
ˆˇ
˄
DIMM1
DIMM2
˄
˄
3V
Battery
1
23456
1
SUPER
I/O
BIOS
~20~
Page 22
BIZ1Aseries
6. 400MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Open Short Short Short Short Short
7. 433MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Open Open Short Short Short Short
ATX POWER
Connector
SUPER
I/O
BIOS
ATX POWER
Connector
SUPER
I/O
BIOS
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
SLOT 1
˄
˄
3V
Battery
ˆˇ
˄
DIMM1
DIMM2
˄
˄
3V
Battery
1
23456
1
8. 466MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Open Short Open Short Short Short
ATX POWER
Connector
SUPER
I/O
BIOS
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
˄
˄
3V
Battery
1
~21~
Page 23
BIZ1Aseries
9. 500MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Open Open Open Short Short Short
10. 533MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Open Short Short Open Short Short
ATX POWER
Connector
SUPER
I/O
BIOS
ATX POWER
Connector
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
SLOT 1
˄
˄
3V
Battery
ˆˇ
˄
DIMM1
DIMM2
˄
˄
3V
Battery
1
23456
1
SUPER
I/O
BIOS
~22~
Page 24
BIZ1Aseries
CPU Bus Speed – 100 MHz Part:
1. 300MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Short Open Short Open Short
2. 350MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Open Open Short Open Short
ATX POWER
Connector
SUPER
I/O
BIOS
ATX POWER
Connector
SUPER
I/O
BIOS
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
SLO T1
˄
˄
3V
Battery
ˆˇ
˄
DIMM1
DIMM2
˄
˄
3V
Battery
1
23456
1
3. 400MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Short Short Open Open Short
ATX POWER
Connector
SUPER
I/O
BIOS
ˆˇ
23456
˄
DIMM1
DIMM2
SLOT1
˄
˄
3V
Battery
1
~23~
Page 25
BIZ1Aseries
4. 450MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Open Short Open Open Short
5. 500MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Short Open Open Open Short
ATX POWER
Connector
SUPER
I/O
BIOS
ATX POWER
Connector
SUPER
I/O
BIOS
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
SLO T1
˄
˄
3V
Battery
ˆˇ
˄
DIMM1
DIMM2
˄
˄
3V
Battery
1
23456
1
6. 550MHz
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6
Short Open Open Open Open Short
ATX POWER
Connector
SUPER
I/O
BIOS
ˆˇ
23456
˄
DIMM1
DIMM2
SLO T1
˄
˄
3V
Battery
1
~24~
Page 26
BIZ1Aseries
CPU TYPE SELECTION LIST
SW1-1,2,3,4 (For RATIO select)
RATIO SW1-1 SW1-2 SW1-3 SW1-4
3.0 ON ON OFF ON
3.5 ON OFF OFF ON
4.0 ON ON ON OFF
4.5 ON OFF ON OFF
5.0 ON ON OFF OFF
5.5 ON OFF OFF OFF
6.0 OFF ON ON ON
SW1-5 (For BUS clock)
CLOCK SW1-5
66 MHz ON
100 MHz OFF
SW1-6 (CPU BUS Clock manual / Auto detect)
CLOCK SW1-6
Default (Auto Detect) ON
Force BUS CLOCK up to 100 MHz OFF
Short Open
~25~
Page 27
BIZ1Aseries
2.3-2 Memory installation
No jumper setting is necessary for DRAM setting; BIOS will check
DRAM type and size automatically. This motherboard contains 2 by 168-pin
DIMM socket (DIMM1, DIMM2). The motherboard has a table-free (or
auto-bank) feature; the user can install DIMM into any bank. The two DIMM
Sockets permit system memory expansion from 8MB to 256MB. Each bank
provides a 64-bit wide data path. You can install 100MHz SPD RAM or
66MHz SD RAM into the motherboard, using your CPU clock to make the
selection.
If you want to install more memory and there are no sockets available,
you must remove some installed modules and replace them with the upgrade
modules.
If you have to do this, be sure to identify what type of memory is already
installed. In some cases, there may be a mix of module types. You can
confirm this by checking the configuration screen that appears while the
computer is starting up. Press the pause key to temporarily interrupt the startup so that you have more time to read the screen. When you’ re done, press
any key to resume.
Remove the lowest performance and smallest size modules and replace
them with the upgrades.
168-pin DIMM Module
BIOS
SUPER
I/O
ATX POWER
Connec tor
SLOT1
DIMM1
DIMM2
3V
Batter y
˄
˄
˄
ˆˇ
~26~
Page 28
BIZ1Aseries
How to Install DIMM Modules on Motherboard
1. The SDRAM sockets are keyed with notches and the DIMMs are keyed
with cut-outs so that they cannot be installed incorrectly. Check that the
cut-outs on the DIMM edge connector match the notches in the SDRAM
socket. In other words, before inserting the DIMM, make sure the pin1 of
the DIMM matches with the pin1 on the DIMM socket.
2. Push down the latches on each side of the SDRAM socket.
3. Install the DIMM into the socket and press it carefully but firmly down so
that it seats correctly. The latches at either side of the socket will be
levered upwards and latch on the edges of the DIMM when it is installed
correctly.
How to Remove DIMM Modules from Motherboard
1. Press the holding the latches at either side of the socket outward to release
the DIMM.
2. Gently pull the DIMM out of the socket.
~27~
Page 29
BIZ1Aseries
NOTE: Samples of System Memory Combinations Options
DIMM1 DIMM2 TOTAL
8MB --- 8MBytes
--- 8MB 8MBytes
8MB 8MB 16MBytes
16MB --- 16MBytes
--- 16MB 16MBytes
8MB 16MB 24MBytes
16MB 8MB 24MBytes
16MB 16MB 32MBytes
32MB --- 32MBytes
--- 32MB 32MBytes
64MB --- 64Mbytes
--- 64MB 64Mbytes
32MB 32MB 64Mbytes
64MB 64MB 128Mbytes
128MB --- 128Mbytes
--- 128MB 128Mbytes
128MB 128MB 256Mbytes
: : :
: : :
: : :
DIMM type : 3.3V, unbuffered or registered, 64/72-bit Synchronous DRAM
with SPD. Supports Single/Double-side 16/32/64/128 Mbytes
module size with parity or non-parity.
~28~
Page 30
BIZ1Aseries
2.3-3 How to install the CPU
Prepare the motherboard by installing the supplied Slot 1 CPU, then
install the CPU according to the instructions supplied. Complete the
processor installation by installing the supplied heat-sink support, and
connecting the heat sink power cable to the motherboard connector.
Referential Steps of installing the Slot 1 CPU
This part is only for CPU installation. Regarding to the heat-sink part, please
refer the instructions supplied.
1. Inspect the area around Slot1, verify the position of four aroundsockets, and then locate the small protruding rectangular tab on the side
of Slot1 (see diagram).
2. Examine the CPU Retention and attachments. There are three sets of
attachments: 1. The stand itself. 2. The CPU locking caps (two). 3.
The plastic screws (four).
~29~
Page 31
BIZ1Aseries
y
t
y
3. Once the above two steps have been completed, slot the CPU Retention
into Slot1. Pull up the CPU stays on both side of the CPU Retention so
they are horizontal, at an angle of 90°. Then the side of the CPU
Retention with no mark on it and the side of Slot1 with the small
rectangular tab should be on the same side.
! The CPU Retention has
to go in a particular direction.
Make sure that it is the right wa
round before slotting it in. Do no
force it in, otherwise you ma
damage the motherboard and
CPU Retention.
4. Ensure that the CPU Retention has been slotted all the way in, then
screw the four plastic screws into the sockets on each side of Slot1 to
make sure that the CPU Retention is fixed firmly in position.
~30~
Page 32
BIZ1Aseries
5. Slide the CPU slowly into Slot1 along the two sides of the CPU
Retention.
Note: Some Slot 1 processors with different packing maybe need the caps to
let them be fixed. So if it need the caps during installing Slot 1 CPU,
please follow this step: “ Fix the CPU locking caps onto the two
ends of the CPU stays ”.
6. Connect the CPU Fan head to the CPU Fan connector on the
motherboard, and make sure that the CPU has been fixed firmly onto
the motherboard. You have now completed assembly.
~31~
Page 33
BIZ1Aseries
SLOT 1 CPU Disassembly/Replacement Procedures
1. Move the protruding part on top of the CPU locking caps gently
outwards, so that the locking caps come off.
2. Pull the CPU Fan connector off the motherboard, and then gently pull
the CPU out from Slot1.
3. If you need to install another CPU, follow the instructions for Slot1
CPU installation given above.
CPU & Power Supply Fan Connectors (3-pin FanPWR)
These connector support cooling fans of 500mAMP (6WATT) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard
heat sink(s) instead of expansion slots. Depending on the fan manufacturer,
the wiring and plug may be different. The red wire should be positive, while
the black should be ground. Connect the fan’ s plug to the board taking into
consideration the polarity of this connector.
The “Rotation” signal is to be used only by a specially designed fan with
rotation signal.
!
The CPU and motherboard will overheat if there is no airflow
across the CPU and onboard heatsinks. Damage may occur to the
motherboard and the CPU fan if these pins are incorrectly used.
~32~
Page 34
BIZ1Aseries
2.3-4 Installing the Motherboard
The BIZ1Aseries motherboard complies with the specifications for an ATX
board, so you can also install this kind of board into a full-size ATX case.
Some features on the motherboard are implemented by cabling connectors on
the motherboard to indicators and switches on the system case. Ensure that
your case supports all the features required. The BIZ1A
can support one or two floppy diskette drives and four enhanced IDE drives.
Ensure that your case has sufficient power and space for all the drives that
you intend to install.
series motherboard
! Caution: Make sure that you have already installed the system
board components like the CPU and memory, and have set the appropriate
jumpers before you proceed.
2.3-5 Installing the interface card
This section explains how to install new interface cards on your
motherboard. It covers installing ISA cards, PCI cards and AGP card. There
are seven expansion card slots on the motherboard, one AGP slot, four PCI
slots and two ISA slots. When you get an expansion card, it will come with
instructions on how to install it, so this section covers relevant information
for the motherboard only.
AGP Card and Slot
The AGP (Accelerated Graphics Port) slot is for an AGP display card.
With the Optimum Settings loaded in the BIOS Setup Utility the AGP has a
default memory aperture of 4MB, expandable to 256MB.
PCI Cards and Slots
With very few exceptions, any PCI expansion card you are likely to get
will be Plug and Play compliant. If you are using an Operating System that
supports PnP, such as Windows 98/95, you should be able to follow the
installation instructions that come with the card and have the Operating
System automatically recognize and configure the card.
~33~
Page 35
BIZ1Aseries
The PCI slots on the motherboard all have “Bus Master” capability. For
installed PCI cards to use this feature, an Operating system specific Bus
Master software driver that comes with this motherboard must be installed
under your Operating System. These drivers are located on the support Disk.
ISA Cards and Slots
ISA expansion cards often use system resources in the form of IRQs and
DMA channels. Newer cards that comply with the Plug and Play (PnP)
standard are designed to allow the Operating System to automatically
configure system resources. Cards that do not support PnP may require
manual configuration of both the card hardware and settings in the CMOS
Setup Utility.
If you have a PnP compliant card to install, there should be little to do
other than follow the installation instructions. If, however, you have a nonPnP card and it requires configuring system resources, you may need to setup
the configuring expansion card resources in CMOS Setup.
2.3-6 Installing Accessory Cables
This section describes how to connector the accessory cables that
motherboard or system housing supports. In the case of ATX, there is no need
to use a bracket to extend the connectors to the rear panel, so here we will
discuss only the installation instructions for Floppy, IDE. Power supply and
Front Panel switch/LED cables.
! Caution: Make sure that the power supply is OFF before
connecting or disconnecting any bracket or cable.
ATX Power Cable
The 20-pin ATX power cable supports 5V standby current and soft
power-on switch. The soft power switch can be either momentary or toggle
~34~
Page 36
BIZ1Aseries
type and must comply with the ATX specification.
Plug in the power cable to the onboard power connector.
SUPER
I/O
BIOS
SLOT1
DIMM1
DIMM2
3V
Battery
˄
˄
ATX POWER
Connecto r
ˆˇ
˄
Front Panel Switch and LED Cables
Normally, the front-panel housing has power switch, power LED, reset
switch, suspend switch, speaker, keylock and HDD LED. These accessories
are included in the housing package and are connector.
Refer to the 2.3-1 “OTHER JUMPER SETTING” for proper location of
the connector.
˄
˄
˄
3V
ˆˇ
ATX POWER
Connecto r
Battery
DIMM2
DIMM1
SLOT1
BIOS
SUPER
I/O
Floppy Cable
The floppy cable for floppy driver is a 34-pin flat cable with 5
connectors classified as follows:
1. Female header (For floppy connector onboard)
2. Female header and Edge connector (For driver B)
3. Female header and Edge connector (For driver A)
The end-most connector cable is twisted to support floppy drive A,
while the middle connectors are for floppy drive B. The drive B connectors
are designed to accommodate both 1.44MB and 1.2MB drives. The female
header supports the 1.44MB drive, while the female edge connector supports
~35~
Page 37
BIZ1Aseries
the 1.2MB drive. When connecting the drive, make sure that pin1 of the cable
(ie., the red-colored wire) matches pin1 of the drive.
˄
˄
˄
3 V
ˆˇ
Battery
DIMM2
DIMM1
ATX POWER
Connector
SLOT1
BIOS
SUPER
I/O
IDE Cables for HDD and CDROM
The motherboard comes with two IDE interfaces; primary IDE and
secondary IDE connectors. Each channel supports two IDE devices via 34pin flat cable; thus enabling the system to accommodate a maximum of four
devices.
˄
˄
˄
3V
ˆˇ
ATX P O WE R
Connector
Batte ry
DIMM2
DIMM1
SLOT 1
BIOS
SUPER
I/O
~36~
Page 38
BIZ1Aseries
Chapter 3
Award BIOS Setup
This chapter explains how to use and modify the BIOS setup utility that
is stored on the motherboard. The setup utility stores information about the
motherboard components, and the configuration of other devices that are
connected to it. The system uses this information to test and initialize
components when it is started up, and to make sure everything runs property
when the system is operating.
The setup utility is installed with a set of default values. The default
values are designed to ensure that the system will operate adequately. You
will probably have to make changes to the setup utility whenever you add
new components to your system such as new disk drives. You may be able to
generate increased performance by changing some of the timing values in the
setup, but this can be limited by the kind of hardware you are using, for
example the rating of your memory chips. In certain circumstances, the
system may generate an error message which asks you to make changes to
the setup utility. This happens when the system finds an error during the
POST (power on self test) that it carries out at start up.
Starting the Setup Utility
You can only start the setup utility shortly after the computer has been
turned on. A prompt appears on the computer display which says " Press
DEL to run Setup”. When you see this prompt press the Delete key, and the
system will start the setup utility and display ft main menu of the utility.
Using the Setup Utility
When you press the Delete key to start setup, the main menu of the
utility appears.
The main menu of the setup utility shows a list of the options that are
available in the utility. A highlight shows which option is currently selected.
You can use the cursor arrow keys to move the highlight to other options.
~37~
Page 39
BIZ1Aseries
When an option is highlighted, you can execute the option by pressing the
Enter key. Some options lead to dialog boxes which ask you verify that that
you wish to execute that option. You usually answer these dialogs by typing
Y for yes and N for no.
Some options lead to dialog boxes which ask for more information.
Setting the User Password or Supervisor Password has this kind of dialog
box.
PRESS F1 TO CONTINUE, CTRL-ALT-ESC OR DEL TO ENTER
SETUP
Control Keys
Up Arrow Move to previous item
Down Arrow Move to next item
Left Arrow Move to the item in the left hand
Right Arrow Move to the item in the right hand
Esc Key Main Menu Quit and not to save changes to CMOS
Status Page setup menu and Option Page
Setup Menu Exit current page and return to Main Menu
PgUp Key Increase the numeric value or make changes
PgDn Key Decrease the numeric value or make changes
F1 Key General help, only for Status Page Setup Menu and Option
Setup Menu
F2 Key Change color from total 16 colors
F3 Key Calendar, only for Status Page Setup Menu
F4 Key Reserved
F5 Key Restore the previous CMOS value from BIOS, only for
Option Page Setup Menu
F6 Key Load the default CMOS value from BIOS default table, only
for Option Page Setup Menu
F7 Key Load the default
F8 Key Reserved
F9 Key Reserved
F10 Key Save all the CMOS changes, only for Main Menu
~38~
Page 40
BIZ1Aseries
3.1 The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu will
appear on the Screen. Use arrow keys to select among the items and press to
accept or enter the sub-menu.
Some options lead to tables of items. These items usually have a value
on the right side. The value of the fust item is highlighted, and you can use
the cursor arrow keys to select any of the other values in the table of items.
When an item is highlighted, you can change the value by pressing the
PageUp or PageDown keys, or the Plus or Minus keys. The PageUp and
Plus keys cycle forward through the available values, the PageDown and
Minus keys cycle backwards through the values.
When you are in the main menu, you can exit the utility by pressing the
Escape key. You can save the current selections and exit the utility by
pressing the F10 key. You can change the color scheme of the utility by
pressing the F2 key while holding down die Shift key. When you are in one
of the options that displays a dialog box, you can return to the main menu by
pressing the Escape key.
When you are in one of the options that displays a table of items, you
can return to the main menu by pressing the Escape key. For some items, you
can display a help message by pressing the Fl key. You can change the color
scheme of the utility by pressing the F2 key while holding down the Shift
key. You can press FS to discard any changes you have made and return all
items to the value that they held when the setup utility was started. You can
press F6 to load the displayed items with a list of default values. You can
press F7 to load the displayed items with a high-performance list of default
values.
~39~
Page 41
BIZ1Aseries
ROM PC/ISA BIOS (2A69KPNI)
CMOS SETUP UTILITY
AWARD SOFTWARE, INC.
STANDARD CMOS SETUP
BIOS FEATURE SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
Esc : Quit ↑ ↓ → ← : Select Item
F10 : Save & Exit Setup (Shift) F2 : Change Color
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
Standard CMOS Setup
This setup page includes all the items in standard compatible BIOS.
BIOS Features Setup
This setup page includes all the items of Award special enhanced features.
Chipset Features Setup
This setup page includes all the items of chipset special features.
Power Management Setup
This menu provides functions for Green products by allowing users to set the
timeout value for monitor and HDD.
PNP / PCI CONFIGURATION SETUP
This menu allows the user to modify PNP / PCI configuration function.
Load BIOS Defaults
BIOS defaults indicates the most appropriate value of the system parameter
which the system would be in minimum performance.
Load Setup Defaults
Chipset defaults indicates the values required by the system for the maximum
performance.
~40~
Page 42
BIZ1Aseries
INTEGRATED PERIPHERALS
This section page includes all the items of IDE hard drive and Programmed
Input / Output features.
Supervisor / User Password Setting
Change, set, or disable password. It allows you to limit access to the system
and Setup, or just to setup.
IDE HDD Auto Detection
Automatically configure hard disk parameters.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
3.2 Standard CMOS Setup
The item in Standard CMOS Setup Menu are divided into several
categories. Each category includes no, one or more than one setup items.
Use the arrow keys to highlight the item and then use the <PgUp> or
<PgDn> keys to select the value you want in each item.
SPN!QDJ0JTB!CJPT!)3B7:LQOJ*
TUBOEBSE!DNPT!TFUVQ
BXBSE!TPGUXBSF-!JOD/
Ebuf!)nn;ee;zz*!;!Uvf-!Efd!3:!2::9
Ujnf!)ii;nn;tt*!;!!:!;!63!;!53
IBSE!EJTLT UZQF
Qsjnbsz!Nbtufs!!!!!!!!
Qsjnbsz!Tmbwf!!!!!!!!!!!
Tfdpoebsz!Nbtufs
Tfdpoebsz!Tmbwf
Esjwf!B!!!;!2/55N-!4/6!jo/
Esjwf!C!!!;!Opof
Gmpqqz!4!Npef!Tvqqpsu!;!Ejtbcmf
Wjefp!!!!;!FHB0WHB
Ibmu!Po!;!Bmm-!Cvu!Lfzcpbse
FTD!!!;!!Rvju
G2!!!!;!!Ifmq
;
;
;
;
TJ[F DZMT IFBE QSFDPNQ MBOE[ TFDUPS NPEF
1
1
1
1
1
1
1
1
1
1
1
1
!!!!!!!!!!!!!;!Tfmfdu!Jufn!!!!!!!!!!!!!!!!!!!!QV0QE0,0.;Npejgz
)Tijgu*!G3!!!;!Dibohf!Dpmps
1
1
1
1
1
1
1
1
!!!!Cbtf!Nfnpsz;!!!!!1L
Fyufoefe!Nfnpsz;!!!!!1L
!!!Puifs!Nfnpsz;!!!623L
!!!Upubm!Nfnpsz;!!!632L
1
1
1
1
1
1
1
1
~41~
Page 43
BIZ1Aseries
Date and Time
The Date and Time items show the current date and time held by your
computer. If you are running a Windows operating system, these items will
automatically be updated whenever you make changes to the Windows Date
and Time Properties utility.
Hard Disks
Default: Auto
These items show the characteristics of any hard disk drives on the four
available IDE channels. (Note that SCSI hard disk drives do not appear here.)
You can automatically install most modem hard disks using the IDE HDD
Auto Detect Option from the main menu. However, if you find that a drive
cannot be automatically detected, you can use these items to select USER,
and then manually enter the characteristics of the drive. The documentation
provided with your drive provides the data you need to fill in the values for
CYLS (cylinders), HEAD (read/write heads), and so on.
The documentation provided with the drive may not tell you what value to
use under the MODE heading. If the drive is smaller than 528 NM, set
MODE to Normal. If the drive is larger dm 528 NM and it supports Logical
Block Addressing, set MODE to LBA- Very few high-capacity drives do not
support Logical Block Addressing. If you have such a drive, you might be
able to configure it by setting the MODE to Large. If you're not sure which
MODE setting is required by your drive, set MODE to Auto and let the setup
utility try to determine the mode automatically.
Drive A and Drive B
Default: 1.44M, 3.5 in., None
These items define the characteristics of any diskette drive attached to the
system. You can connect one or two diskette drives.
Floppy 3 Mode Support
Default: Disabled
Floppy 3 mode refers to a 3.5" diskette with a capacity of 1.2MB. Floppy 3
mode is sometimes used in Japan.
Video
Default: Disabled
This item defines the video mode of the system. This motherboard has a
built-in VGA graphics system so you must leave this item at the default
value.
Halt On
Default: All. But Keyboard
This item defines the operation of the system POST (Power On Self Test)
~42~
Page 44
BIZ1Aseries
routine. You can use this item to select which kind of errors in the POST is
sufficient to halt the system.
Base, Extended and Other Memory
Default: All. But Keyboard
These items show how much memory is available on the system. They are
automatically detected by the system so you cannot manually make changes
to these items.
3.3 BIOS Features Setup
This option displays a table of items which defines more advanced
information about your system you can make modifications to most of these
items without introducing fatal errors to your system.
ROM PCI/ISA BIOS (2A69KPNI)
BIOS FEATURE SETUP
AWARD SOFTWARE, INC
Anti-Virus Protection : Enabled Video BIOS Shadow
CPU Internal Cache : Enabled C8000-CBFFF Shadow
External Cache : Enabled CC000-CFFFF Shadow
CPU L2 Cache ECC Checking : Enabled D0000-D3FFF Shadow
Processor Number Feature : Enabled D4000-D7FFF Shadow
Quick Power On Self Test : Enabled D8000-DBFFF Shadow
Boot Sequence : A, C ,SCSI DC000-DFFFF Shadow
Swap Floppy Drive : Disabled
Boot Up Floppy Seek
Boot Up NumLock Status : On
Gate A20 Option : Fast
Typematic Rate Setting : Disabled
Typematic Rate (Chars/Sec) : 6
Typematic Delay (Msec) : 250
Security Option : Setup
PCI/VGA Palette Snoop : Disabled
OS Select For DRAM > 64MB
HDD S.M.A.R.T. capability
Report No FDD For Win95
:
Disabled
: Non-OS2
: Enabled
: No
Esc : Quit ↑↓→← : Selection Item
F1 : Help PU/PD/+/- : Modify
F5 : Old Values (Shift) F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
: Enabled
: Disabled
: Disabled
: Disabled
: Disabled
: Disabled
: Disabled
~43~
Page 45
BIZ1Aseries
Anti-Virus Protection Default: Enabled
Anti-Virus program could locate and remove the problem before any
damage is done. So when this item is enabled, the Award BIOS will monitor
the boot sector and partition table of the hard disk drive for any attempt at
modification. If an attempt is made, the Anti-Virus program built-in the BIOS
will be run for protecting your system to be clean.
! WARNING:
Disk boot sector is to be modified
Type 'Y' to accept write or 'N' to abort write
Award Software, Inc.
Enabled : Activates automatically when the system boots up, if anything
attempts to access the boot sector or hard disk partition table will
cause a warning message to appear.
Disabled : No warning message will appear when anything attempts to access
the boot sector or hard disk partition table.
Many disk diagnostic programs which attempt to access the boot sector table
can cause the above warning message.
CPU Internal Cache
Default: Enabled
All the processors that can be installed in this motherboard use internal (level
1) cache memory to improve performance. Leave this item at the default
value Enabled for better performance.
External Cache
Default: Enabled
Most of the processor cartridges that can be installed in this
motherboard have (level 2) external cache memory (the Celeron266MHz is an exception). Only enable this item if your processor
cartridge has external cache memory.
CPU L2 Cache ECC Checking
Default: Enabled
This item can be used to enable ECC (Error Checking Code) for the level-2
cache memory. We recommend that you leave this item at the default value
Enabled.
~44~
Page 46
BIZ1Aseries
Processor Number Feature
Default: Enabled
This item can be used to enable Intel Pentium III processor serial number. It
can let others know who is you when you on the web. If you want keep your
secrets, please choose disabled.
Quick Power On Self Test
Default: Enabled
You can enable this item to shorten the power on testing and have your
system start up a little faster.
Boot Sequence
Default: A, C, SCSI
This item defines where the system will look for an operating system, and the
order of priority. You can boot an operating system from many locations
including a SCSI device, a ZEP drive, a floppy diskette drive, or an LS-120
high-capacity diskette drive.
Swap Floppy Drive
Default: Disabled
If you have two floppy diskette drives in your system, this item allows
you to swap around the assigned drive letters so that drive A becomes
drive B, and drive B becomes drive A.
Boot Up Floppy Seek
Default: Disabled
During POST, BIOS will determine if the Floppy disk drive installed is 40 or
80 tracks. 360 K type is 40 tracks while 720K, 1.2M and 1.44M drive type as
they are all 80 tracks.
Enabled: BIOS searches for floppy disk drive to determine if it is 40
or 80 tracks. Note that BIOS can not tell from 720K, 1.2M or
1.44M drive type as they are all 80 tracks.
Disabled:
BIOS will not search for the type of floppy disk drive by
track number. Note that there will not be any warning
message if the drive installed is 360K.
Boot Up NumLock Status
Default: On
This item defines if the keyboard Num Lock key is active when your system
is started.
Gate A20 Option
Default: Fast
This option provides compatibility with older software written for the 286
processor. Leave this item at the default value Fast.
~45~
Page 47
BIZ1Aseries
Typematic Rate Setting
Default: Disabled
This determines if the typematic rate is to be used. When disabled,
continually holding down a key on your keyboard will generate only one key
instance. In other words, the BIOS will only report that the key is down.
When the typematic rate is enabled, the BIOS will report as before, but it will
then wait a moment, and, if the key is still down, it will begin the report that
the key has been depressed repeatedly. For example, you would use such a
feature to accelerate cursor movements with the arrow keys.
Typematic Rate (Chars/Sec)
Default: 6
When the typematic rate is enabled, this section allows you select the rate at
which the keys are repeated.
6 6 characters per second
15 15 characters per second
8 8 characters per second 20 20 characters per second
1 0 1 0 characters per second 24 24 characters per second
12 12 characters per second 30 30 characters per second
Typematic Delay (Msec)
Default: 250
When the typematic rate is enabled, this section allows you select the delay
between when the key was first depressed and when the acceleration begins.
250 250 msec
500 500 msec
750 750 msec
1000 1000 msec
Security Option
Default: Setup
If you have installed password protection, this item defines if the password is
required at system start up, or if it is only required when a user tries to enter
the setup utility.
PCI/VGA Palette Snoop
Default: Disabled
This item can help overcome problems that are caused by some non-standard
VGA cards. We recommend that you leave this item at the default value
Disabled.
OS Select For DRAM > 64 MB
Default: Non-OS2
This item is required if you have installed more than 64 NM of memory and
you are running the OS/2 operating system. Otherwise, leave this item at the
default Non-OS2.
~46~
Page 48
BIZ1Aseries
HDD S.M.A.R.T Capability
Default: Enabled
S.M.A.R.T is an industry acronym for Self-monitoring, Analysis and
Reporting Technology. If the documentation of your hard disk states that
S.M.A.R.T. is supported, you can enable this item.
Report No FDD For WIN 95
Default: No
Set this item to Yes BIOS will report FDD to Win95. If in standard CMOS
setup, set Drive A to none, and set this item to yes. Inside Win95, My
Computer and File manager Disk(A:) will show Removable Disk (A:).
Video BIOS Shadow
Default: Enabled
This item allows the video BIOS to be copied to system memory for faster
performance.
XXXXX-XXXXX Shadow
Default: Disabled
These items allow the BIOS of other devices to be copied to system memory
for faster performance.
~47~
Page 49
BIZ1Aseries
3.4 Chipset Features Setup
This option displays a table of items which define timing parameters of the
motherboard components including the graphics system, the memory, and the
system logic. In general rule, you should leave the items on this page at the
default values unless you are very familiar with the technical specifications
of your hardware. If you change the values, you may introduce fatal errors or
recurring instability into your system.
ROM PCI/ISA BIOS (2A69KPNI)
CHIPSET FEATURES SETUP
AWARD SOFTWARE, INC
Auto Configuration
EDO DRAM Speed Selection
EDO CASX# MA Wait State
EDO RASX# Wait State
SDRAM RAS-to-CAS Delay
SDRAM RAS Precharge Time
SDRAM CAS latency Time
SDRAM Precharge Control
System BIOS Cacheable
Video BIOS Cacheable : Enabled IN2 (V) : +5V
Video RAM Cacheable : Enabled +12 V : -12V : -
8 Bit I/O Recovery Time : 1 - 5 V : -
16 Bit I/O Recovery Time : 1 Shutdown Temperature : 60oC/140oF
Memory Hole At 15M-16M : Disabled
Passive Release : Enabled
Delayed Transaction
AGP Aperture Size (MB)
: Enabled
: 60ns
: 1
: 2
: 3
: 3
: 3
: Disabled
: Enabled
: Disabled
: 64
Auto Detect DIMM/PCI Clk
Spread Spectrum Modulated
CPU Host/PCI Clock
CPU Warning Temperature
Current System Temp.
Current CPU1 Temperature
Current CPUFAN1 Speed
Current CPUFAN2 Speed
IN0 (V) : IN1(V)
Esc : Quit ↑↓→← : Selection Item
F1 : Help PU/PD/+/- : Modify
F5 : Old Values
F6 : Load BIOS Default
F7 : Load Setup Default
(Shift) F2 : Color
: Enabled
: Disabled
: Default
: Disabled
:
:
:
:
:
Auto Configuration
Default: Enabled
This function can make BIOS auto-setting the best DRAM parameter.
EDO DRAM Speed Selection
Default: 60ns
This item defines the timing parameters for the system memory. We
recommend that you leave these items at the default values EDO 60ns.
~48~
Page 50
BIZ1Aseries
EDO CASX# MA Wait State
EDO RASX# Wait State
SDRAM RAS-to-CAS Delay
SDRAM RAS Precharge Time
SDRAM CAS latency Time
SDRAM Precharge Control
Default: 1
Default: 2
Default: 3
Default: 3
Default: 3
Default: Disabled
These items are setting by Auto Configuration.
Auto Configuration : By default, this parameter is set to Enabled. This
automatically enters and locks the optimum settings for the chipset. Disable
the parameter to unlock the settings without changing them.
System BIOS Cacheable
Default: Enabled
System BIOS segment is cacheable if this item been enable.
Video BIOS Cacheable
Default: Enabled
Video BIOS segment is cacheable if this item been enable.
Video RAM Cacheable
Default: Enabled
Video RAM segment is cacheable if this item been enable.
8 Bit I/O Recovery Time
Default: 1
The recovery time is the length of time, measured in CPU clocks, which the
system will be delay after the completion of an I/O request. This delay takes
place because the CPU is operating so much faster than the input/output bus
that the CPU must be delayed to allow for the completion of the I/O. This
item allows you to determine the recovery time allowed for 8- bit 1/0.
Choices are from NA, 1 to 8 CPU clocks,
16 Bit I/O Recovery Time
Default: 1
This item allows you to determine the recovery time allowed for 16-bit 1/0.
Choices are from NA, I to 4 CPU clocks.
Memory Hole At 15M-16M
Default: Disabled
In order to improve performance, certain space in memory can be reserved
for ISA cards. This memory must be mapped into the memory below 16MB.
~49~
Page 51
BIZ1Aseries
Passive Release
Default: Enabled
When Enabled, CPU to PCI bus accesses is allowed during passive release.
Otherwise, the arbiter only accepts another PCI master access to local
DRAM.
Delayed Transaction
Default: Disabled
This chipset has an embedded 32-bit posted write buffer to support deadly
transactions cycles. Select Enabled to support compliance with PCI
specification version 2. 1.
AGP Aperture Size (MB)
Default: 64
Select the size of the AGP aperture. The aperture is a portion of the PCI
memory address range dedicated for graphics memory address space. Host
cycle that hit the aperture range is forwarded to the AGP without any
translation. The choice 4, 8, 16, 32, 64, 128, 256.
Auto Detect DIMM/PCI Clk
Default: Enabled
If this item is enabled, the unused DIMM and PCI slot clock will be disabled.
If this item is disabled the unused DIMM and PCI slot will still get the active
clock signal.
Spread Spectrum Modulated
Default: Disabled
Enable / Disable this item the BIOS will Enable / Disable the clock generator
spread spectrum.
CPU Host/PCI Clock
Default: Default
This item allows other PCI devices to work concurrently with the host PCI
IDE channel. We recommend that you leave this item at the default value
Disabled.
CPU Warning Temperature
Default: Disabled
When this item is enabled, we can set the CPU warning temperature. If the
CPU temperature is higher than the setting temperature, the system will beep.
Current System Temp.
This field displays the current system temperature, if your computer contains
a monitoring system.
Current CPU1 Temperature
It shows the current CPU temperature.
~50~
Page 52
BIZ1Aseries
Current CPUFAN1 Speed
Current CPUFAN2 Speed
Current CPUFAN3 Speed
It shows the running speed of the system fan, Chassis fan and power fan.
The value will be changing when the system is running. If you do not
install the fan, the value will show 0.
Shutdown Temperature
Default: 60OC/140OF
When the system temperature up to 60OC/140OF, it will be shutdown.
Note:
The items on the right side of the Chipset Features option are
concerned with monitoring certain temperatures, voltages, and so on in
your system. These items do not function unless you have installed an
optional system-monitoring clip on your motherboard.
3.5 Power Management
This option displays a table of items which lets you control the power
management of the system. Modern operating systems take care of much of
the routine power management. This motherboard supports ACPI (advanced
configuration and power interface).
This system supports three levels of power-saving modes; doze mode,
standby mode, and suspend mode. Standby mode uses less power than doze
mode and suspend mode uses the least power.
The power management in the setup utility lets you specify a timeout for
each of the power-saving modes, and a timeout for a hard disk drive power
down. A timeout, means a period of time when the system (or the hard disk
drive) is inactive. If the timeout completes, the system power-saving mode
will execute, or the hard disk drive will power down.
~51~
Page 53
BIZ1Aseries
You can resume from the power-saving modes by carrying out any of
the activities which are enabled in the list Reload Global Timer Events. If the
hard disk has been powered down it will automation resume to full power
when an access to the hard disk is required (this takes just a few seconds).
ROM PCI/ISA BIOS (2A69KPNI)
POWER MANAGEMENT SETUP
AWARD SOFTWARE, INC.
ACPI function : Enabled ** Reload Global Timer Events **
Power Management : User Define IRQ [3-7,9-15],NMI : Disabled
PM Control by APM : Yes Primary IDE 0 : Disabled
Video Off Method : V/H SYNC+Blank Primary IDE 1 : Disabled
Video off After : Standby Secondary IDE 0 : Disabled
MODEM Use IRQ : 3 Secondary IDE 1 : Disabled
Doze Mode : Disable Floppy Disk : Disabled
Standby Mode : Disable Serial Port : Enabled
Suspend Mode : Disable Parallel Port : Disabled
HDD Power Down : Disable
Throttle Duty Cycle : 62.5%
PCI/VGA Act-Monitor : Enabled
Soft-off by PWR-BTTN : Instant-off
CPUFAN off In Suspend : Enabled
Poweron by Ring : Enabled
Resume by Alarm : Disabled
Wake Up on LAN : Enabled F6 : Load BIOS Defaults
IRQ 8 Break Suspend : Disabled F7 : Load Setup Defaults
ECS
: Quit ↑↓→← : Selection Item
F1 : Help PU / PD / + / - : Modify
F5 : Old Values (Shift)F2 : Color
ACPI function
Default: Enabled
When Enabled, this function can save the power of your system.
Power Management
Default: User Define
This category allows you to select the type (or degree) of power saving and is
directly related to the following modes : Doze; Standby; Suspend; HDD
Power Down.
Min.Power Minimum power management. Doze =I hr.;
Saving Standby= I hr.; Suspend= I hr.; HDD Power Down=15min
Max. Power Maximum power management only
Saving available for SL CPU.Doze=lmin.;
Standby=lmin.;Suspend=l min.;HDD Power Down= l min
User Allows you to set each mode individually.
~52~
Page 54
BIZ1Aseries
Defined When not disabled, each of the ranges are from I min. to I
hr. except for HDD Power Down which ranges from I to
15min. and disable
If you would like to use Software Power-off Control function, you cannot
choose" Disabled "here, and should select "Yes" in PM Control by APM.
PM Control by APM
Default: Yes
Windows 95 and 98 have built-in power management capabilities called
APM (advanced power management). When you enable this item, you allow
the APM routines in Windows to operate on your system.
Video Off Method
Default: V/H SYNC+Blank
This determines the manner in which the monitor is blanked.
V/H SYNC+ Blank This selection will cause the system to turn off the
vertical and horizontal sync. ports and write
blanks to the video buffer
Blank This option only writes blanks to the
Screen video buffer
DPMS Initial display power management signaling
Video Off After
Default: Standby
When enabled, this feature allows the VGA adapter to operate in a power
saving mode.
N/A Monitor will remain on during power saving
modes.
Suspend Monitor blanked when the systems enters the
Suspend mode.
Standby Monitor blanked when the system enters Standby
mode.
Doze Monitor blanked when the system enters any
power saving mode.
MODEM Use IRQ
Default: 3
This item determines the IRQ in which the MODEM can be used.
The choice: 3,4,5,7,9, 10,11,N/A.
Doze Mode
Default: Disable
If you have selected User Define for the Power Management item, you can
set this item to a selection of timeouts from 20 seconds to 40 minutes.
~53~
Page 55
BIZ1Aseries
Standby Mode
Default: Disable
When enabled and after the set time of system inactivity, the fixed disk drive
and the video would be shut off while all other devices still operate at full
speed.
Suspend Mode
Default: Disable
If you have selected User Define for the Power Management item, you can
set this item to a selection of timeouts from 20 seconds to 40 minutes.
HDD Power Down
You can use this item to set a timeout for a hard disk powerdown. You can set a time
from I to 15 minutes. If the hard disk is inactive for the time specified, it will power
down. It will automatically return to full power when it is next accessed.
Throttle Duty Cycle
Default: Disable
Default: 62.5%
When the system enters Doze mode, the CPU clock runs only part of time.
You may select the percent of time that the clock runs.
PCI/VGA Act-Monitor
Default: Enabled
When Enabled, any video active restarts the global timer for standby mode.
Soft-off by PWR-BTTN
Default: Instant-off
Under ACPI (advanced configuration and power interface) the system can be
turned off mechanically (by the power button) or it can undergo a software
power off. If the system has been turned off by software, the system can be
resumed by a LAN, MODEM or ALARM wake up signal. This item allows
you to define a software power off using the power button. If the value is set
to Instant-Off, the power button will automatically cause a software power
off. If the value is set to Delay 4 Sec. the power button must be held down for
a full four seconds to cause a software power off.
CPUFAN off In Suspend
Default: Enabled
Enabled: under suspend mode, the CPU FAN will be turn off.
Disabled: suspend mode will not turn off CPU FAN.
PowerOn by Ring
Default: Enabled
Enabled: when system in suspend mode, it can be wake up by modem.
Disabled: it cannot be wake up by modem.
~54~
Page 56
BIZ1Aseries
Resume by Alarm
Default: Disabled
When Enabled, two additional lines will be added to the screen Date (of
Month) Alarm; Time (hh:mm:ss) Alarm to let user set the desired date and
time. After power off, the system will automatic power on at the specified
date and time.
Wake Up On LAN
Default: Enabled
Enabled: If you have installed LDCM administrator software, and any client
side is powered off, you can wake up by LAN through the LDCM
mechanism.
IRQ 8 Break Suspend
Default: Disabled
When enabled, the device which occupies the IRQ8 can wake up the system.
Reload Global Timer Events
When enabled, an event occurring on each device listed below restarts the
global time for Standby mode.
IRQ [3 -7, 9-15], NM;
Primary IDE 0;
Primary IDE 1;
Secondary IDEO;
Secondary IDEL;
Floppy Disk;
~55~
Page 57
BIZ1Aseries
3.6 PNP/PCI Configuration Setup
The PNP/PCI Configuration Setup allows you to configure the ISA and PCI
devices installed in your system. The following screen appears if you select
the option PNP/PCI Configuration setup from the main menu.
ROM PCI/ISA BIOS(2A69JPNE)
PNP/PCI CONFIGURATION
AWARD SOFTWARE, INC.
PNP OS Installed : No PCI IDE IRQ Map To : PCI-AUTO
Resources Contorlled By : Manual Primary IDE INT# : A
Reset Configuration Data : Disabled Secondary IDE INT# : B
IRQ-3 assigned to : PCI/ISA PnP
IRQ-4 assigned to : PCI/ISA PnP
IRQ-5 assigned to : PCI/ISA PnP
IRQ-7 assigned to : PCI/ISA PnP Used MEM base addr : N/A
IRQ-9 assigned to : PCI/ISA PnP
IRQ-10 assigned to : PCI/ISA PnP Assign IRQ For VGA : Enabled
IRQ-11 assigned to : PCI/ISA PnP Assign IRQ For USB : Enabled
IRQ-12 assigned to : PCI/ISA PnP
IRQ-14 assigned to : PCI/ISA PnP
IRQ-15 assigned to : PCI/ISA PnP
DMA-0 assigned to : PCI/ISA PnP
DMA-1 assigned to : PCI/ISA PnP
DMA-3 assigned to : PCI/ISA PnP F1 : Help PU / PD / + / - : Modify
DMA-5 assigned to : PCI/ISA PnP F5 : Old Values (Shift)F2 : Color
DMA-6 assigned to : PCI/ISA PnP F6 : Load BIOS Defaults
DMA-7 assigned to
: PCI/ISA PnP F7 : Load Setup Defaults
ESC: Quit ↑↓→←: Select Item
PNP OS Installed
Default: No
If you have installed a Plug and Play operating system such as Windows 95 or 98,
you can change this item to Yes. When the item is set to Yes you can use the Device
Manager utility in the operating system to make changes to the configuration of
expansion cards.
Resources Controlled By
Default: Manual
You should leave this item at the default Auto. If you find that you cannot get
a particular expansion card to work properly, you might be able to solve the
problem by changing this item to Manual, and defining the characteristics of
the card in the new items which appear.
If you change this item to Manual, the display will list a series of items that
~56~
Page 58
BIZ1Aseries
allow you to define the assignments of the system interrupt lines (IRQS) and
Direct Memory Access (DMA) channels. As a default, these items are set to
PCI/ISA PnP. If you install an ISA Bus card that does not support PNP, and it
requires a special IRQ and DMA, you can modify the list of assignments.
Change the values of the IRQ and DMA that are required to Legacy ISA.
Reset Configuration Data
Default: Disabled
If you enable this item and restart the system, any PNP configuration data
stored in the BIOS setup will be cleared from memory. New updated
configuration data will be created.
IRQ 3/4/5/7/9/10/11/12/14/15
DMA 1/3/5/6/7
This item allows you to determine the IRQ/DNM assigned to the ISA bus and
is not available to any PCI slot. Choices are Legacy ISA and PCI/ISA PnP.
PCI IDE IRQ MAP To
Default: PCI-AUTO
Primary IDE INT#
Secondary IDE INT#
This allows you to configure your system to the type of IDE disk controller in
use. By default, Setup assumes that your controller is an ISA device rather
than a PCI controller. The most apparent difference is the type of slot being
used. If you have equipped your INT# system with a PCI controller, changing
this allows you to specify which slot holds the controller and which PCI
interrupt (A,B,C,D) is associated with the connected hard disk. This setting
refers to the hard disk drive itself, rather than individual partitions. Since
each IDE controller supports two separate hard drives, you can select the
INT# for each. Again, you will note that the primary has a lower interrupt
than the secondary as described in " lot x Using INT# “above. Select “PCI
Auto” allows the system to automatically determine how your IDE disk
system is configured.
Used MEM base addr
This item allows you to determine which basic address will not be occupied by PCI
card and leave these address for some special ISA card used only.
Choices are C800, CCOO, DOOO, D400, D800, DCOO.
Default: N/A
~57~
Page 59
BIZ1Aseries
Assign IRQ For VGA
Default: Enabled
To assign an IRQ to VGA card if you enable this item.
Assign IRQ For USB
Default: Enabled
To assign an IRQ to USB Ports if you enable this item.
3.7 Integrated Peripherals
This option displays a list of items which defines the operation of some
peripheral items on the system's input/output ports.
ROM PC/ISA BIOS(2A69KPNI)
INTEGRATED PERIPHERALS
AWARD SOFTWARE, INC.
IDE HDD Block Mode : Enabled Onboard Serial Port 1
IDE Primary Master PIO : AUTO Onboard Serial Port 2
IDE Primary Slave PIO : AUTO UART Mode Select
IDE Secondary Master PIO : AUTO
IDE Secondary Slave PIO : AUTO
IDE Primary Master UDMA : AUTO Onboard Parallel port
IDE Primary Slave UDMA : AUTO Parallel Port Mode
IDE Secondary Master UDMA : AUTO ECP Mode Use DMA : 3
IDE Secondary Slave UDMA : AUTO EPP Mode Select : EPP1.9
On-Chip Primary PCI IDE : Enabled
On-Chip Secondary PCI IDE : Enabled
USB keyboard Support : Disabled
Init Display First
POWER ON Function
KBC input clock
Onboard FDC Controller
FDC Write Protect
: PCI Slot
: BUTTON ONLY
: 8 MHz
: Enabled
: Disabled
Esc : Quit ↑↓→← : Selection Item
F1 : Help PU/PD/+/- : Modify
F5 : Old Values (Shift) F2 : Color
F6 : Load BIOS Default
F7 : Load Setup Default
: 3F8/IRQ4
: 2F8/IRQ3
: Normal
: 378/IRQ7
: ECP+EPP
~58~
Page 60
BIZ1Aseries
IDE HDD Block Mode
Default: Enabled
This allows your HDD controller to use the fast block mode to transfer data
to and from your HDD drive; Enabled IDE controller uses block mode ;
Disabled IDE controller uses standard mode.
IDE Primary Master/Slave PIO
Default: Auto
IDE Secondary Master/Slave PIO
PIO - Programmed Input / Output, it allows the BIOS to tell the controller
what it wants and then let the controller and the CPU to complete the task by
themselves. This is simpler and faster. Your system supports five modes, 0 - 4,
which primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.
IDE Primary Master/Slave UDMA
Default: Auto
Auto, will support the Ultra DMA function. Disabled, will not support the
Ultra DMA function.
On-Chip Primary PCI IDE
Default: Enabled
On-Chip Secondary PCI IDE
This setup item allows you to either enable or disable the primary/secondary
controller. You might choose to disable he controller if you were to add
higher performance or specialized controller.
USB Keyboard Support
Default: Disabled
Enabled will support USB keyboard in Win95 2.1 and NT 5.0 or above
operating system.
Init Display First
Default: PCI Slot
Use this item to define if your graphics adapter is installed in one of the PCI
slots, or if you have installed an AGP graphics adapter into the AC-RP slot.
POWER ON Function
Default: BUTTON ONLY
The Power On Function item allows you to power on the system by pressing
hot-keys. If you set this item to Hot Key, you can use the item Hot Key
Power On to choose which hot keys are installed.
KBC input clock
Default: 8 MHz
This item lets you set a frequency for the input clock of the keyboard
controller. Leave this item at the default value 8 MHz.
~59~
Page 61
BIZ1Aseries
Onboard FDC Controller
Default: Enabled
This item will enable or disable the floppy disk controller.
FDC Write Protect
Default: Disabled
To enable/disable the write protection of floppy.
Onboard Serial Port 1
Default: 3F8/IRQ4
User can select serial port IRQ. If set to Auto, system will assign an IRQ for
it. Note : Set to Auto is not recommended.
Onboard Serial Port 2
Default: 2F8/IRQ3
User can select serial port IRQ. If set to Auto, system will assign an IRQ for
it. Note : Set to Auto is not recommended.
UART Mode Select
Default: Normal
This lets you select the Infrared mode. Choices are Standard, HPIR, and
ASKIR. If you choose BPIR or ASKIR mode, the screen will show another
two lines to let you choose 'IR Function Duplex' (Full or Half) and “ RxD
TxD Active” (Hi Lo; Lo Hi; Hi Hi-,Lo Lo).
Onboard Parallel Port
Default: 378/IRQ7
This item lets you disable the built-in parallel port, or enable it by assigning a
1/0 address and an Interrupt Request Line (IRQ).
Parallel Port Mode
This item defines the operation of the parallel port. As a default it is set to ECP +
EPP. If you are connected to a parallel device that supports the higher-performance
EPP (enhanced parallel port) or the ECP (extended capabilities port) make the
appropriate changes to this item. If you change the parallel port to EPP or ECP, new
items appear that let you
ECP Mode Use DMA
Default: ECP+EPP
Default: 3
Select a DMA channel for the port. Choices are 3, 1.
EPP Mode Select
Default: EPP1.9
Select EPP mode for the port.
~60~
Page 62
BIZ1Aseries
3.8 Supervisor Password & User Password
These two items can be used to install a Supervisor Password and a User
Password. If you log on as Supervisor, you have full access to the system,
and you can restrict the permissions granted to someone who logs on as User.
For example, a Supervisor can restrict a User from entering the setup utility.
To install a Supervisor or User Password, follow these steps:
1. Highlight the item Supervisor/User password on the main menu and press
Enter.
2. The password dialog box will appear.
3. If you are installing a new password, carefully 4W in the password. You
cannot use more than 8 characters or numbers. The password will
differentiate between upper case and lower characters. Press Enter after
you have typed in the password. If you are deleting a password that is
already installed just press Enter when the password dialog box appears.
4. The system will ask you to confirm the new password by asking you to
type it in a second time, Carefully type the password again and press Enter,
or just press Enter if you are deleting a password that is already installed.
5. If you type the password correctly, the password will be installed.
3.9 IDE HDD Auto Detection Option
This feature allows you to check all the information on your hard disk
formation. When you access "IDE HDD Auto Detection", the system
executes auto detection.
At the prompt, it represents all the information on your HDD, and you
are asked:
Do you accept this drive C: (Y/N) ?
1. If you accept the test result, press [Y] then [Enter] and the result is saved,
then the system continues to detect another HDD.
7. If not, press [N] then [enter] and the system continues to detect
another HDD.
~61~
Page 63
BIZ1Aseries
3.10 Save and Exit Setup Option
This allows you to save the new setting values in the CMOS memory
and continue with the booting process. Select what you want to do, press
<Enter>.
3.11 Exit Without Saving Option
This allows you to exit the BIOS setup utility without recording any new
values or changing old ones.
Highlight this item and press Enter to save the change that you have made in
the setup utility and exit the setup program. When the Save and Exit dialog
box appears, press Y to discard changes and exit, or press N to return to the
setup main menu.
~62~
Page 64
BIZ1Aseries
Chapter 4
Software Setup
The support software for this motherboard may be supplied on a CDTitle, or it may be supplied on diskettes. All the support programs are stored
in separate folders, so you can find the program you need easily enough. The
support software contains the following programs:
! IDE Bus Master drivers for Win 95/NT.
! PC-Cillin 98 Software.
Note: Please refer the PC-Cillin 98 installation guide for installing the PC-
Cillin 98.
4.1 Installing the IDE Bus Master Driver
After you have finished the hardware setup, you have to install the IDE
Bus Master software of the motherboard, then you can enjoy the advance
Motherboard.
Note: If your system is Win98, please skip this section. Because Windows
98 have been built-in the IDE Bus Master Driver, you don’ t need to
install the software again.
According the follow steps for IDE Bus Master driver installation:
1. Turn on your PC then put the “CD title” into your CD-ROM drive.
(Please make sure it’ s under Win98/95 mode)
2. The CD title will be auto-run. If not, please click the “start” button and
select “Run” item. Then type-> D:\setup (D is assigned your CD-
ROM Device)
~63~
Page 65
BIZ1Aseries
3. Press “Intel BX,ZX,LX,EX” button.
Intel BX.ZX,LX,ZX button
4. Press “WINDOWS 95 BUS MASTER” and follow the instructions to
this software. Then Re-boot your PC.
WINDOWS 95 BUS MASTER button
5. Click Next when the Welcome screen appears.
6. Follow the instructions to complete the software installation, then re-
boot your PC.
~64~
Page 66
BIZ1Aseries
Click here
Click here
4.2 The Temperature Sensor
– W83781D (Optional)
This program is concerned with monitoring certain temperatures,
voltages, and so on in your system. These items do not function unless
your motherboard has W83781D sensor chip and you have installed
following software on your motherboard.
Hardware Doctor Setup for Windows 95 or 98:
1. Turn on your PC and put the “CD title” into your CD-ROM drive.
(Please make sure it’ s under Win98/95 mode)
2. The CD title will be auto-run. If not, please click the “start” button and
select “Run” item. Then type-> D:\setup (D is assigned your CD-
ROM Device)
3. Click the Install Hardware Doctor Utility.
3. Click the W83781D and follow the instruction to finish the installation,
then reboot your computer.
Run the Hardware Doctor program.
~65~
Page 67
BIZ1Aseries
♦ Voltage default -
The Application of W83781D also controls the fan speed. The
default of CPU Fan, SYS1 Fan and SYS2 Fan is “Enable”.
♦ When you connect just only one CPU Fan -
If your system is using CPU Fan only, please disable the function of SYS1
Fan and SYS2 Fan by the following steps:
1. When you complete the setup and reboot the system, the system will
alarm with a warning “beep“ sound. Please click the “START”
!”PROGRAM” buttons and select the “Hardware Doctor”, the system
will display the message as next page:
~66~
Page 68
BIZ1Aseries
2. Click the “Disable” of the warning icon of Fan 3, then it shows the
warning icon of Fan 2. You just click the “Disable” icon as previous
step. Then “Save” and “Exit”.
The correct setup is completed.
~67~
Page 69
BIZ1Aseries
This page was intentionally left blank
~68~
Page 70
BIZ1Aseries
This page was intentionally left blank
~69~
Loading...