Procom Heating MN100HPA, MN060HPA, MN100TPA User Manual

VENT-FREE NATURAL GAS

SPACE HEATER

OWNER’S OPERATION AND

INSTALLATION MANUAL

INFRARED MODELS

MN060HPA, MN100HPA

MN100TPA

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable va-

pors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

—

Installation and service must be performed by a qualied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Questions, problems, missing parts? Before returning to your retailer, call

our customer service department at 1-866-573-0674, 7:30 am - 4:15 pm CST,

Monday through Friday or email customerservice@usaprocom.com

TABLE OF CONTENTS

Safety ........................................................ 3

Specications ............................................ 4

Product Identication ................................. 5

Qualied Installing Agency ........................ 5

Product Features ....................................... 5

Local Codes............................................... 6

Unpacking.................................................. 6

Water Vapor: A By-Product Of

Unvented Room Heaters ..................... 6

Air For Combustion and Ventilation ........... 7

Installation ................................................. 9

Operation ................................................. 15

Inspecting Heater .................................... 18

Care And Maintenance ............................ 19

Troubleshooting ....................................... 20

Replacement Parts .................................. 23

Accessories ............................................. 23

Service Hints ........................................... 23

Technical Service..................................... 23

Parts ........................................................ 24

Warranty .................................................. 32

SAVE THIS BOOK

This is an unvented gas-red heater. It uses air (oxygen)

from the room in which it is installed. Provisions for ad-

equate combustion and ventilation air must be provided.

Refer to Air For Combustion and Ventilation section on page 7 of this manual.

WARNING: Improper installation, adjustment, al-

teration, service or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance

or additional information consult a qualied installer,

service agency or the gas supplier.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convert-

ible for use with other gases.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.

www.usaprocom.com

200048-01D2

SAFETY

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death

from burns, fire, explosion, electrical shock and carbon

monoxide poisoning.

Only a qualied installer, service

agent, or local gas supplier may install and service this product.

WARNING: Keep the appli-

ance area clear and free from

combustible materials, gasoline, and other ammable vapors and

liquids.

This heater is equipped for natural gas. Field conversion is not permitted.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance

is not convertible for use with

other gases.

DANGER: Carbon monoxide

poisoning may lead to death!

CARBON MONOXIDE POISONING: Early

signs of carbon monoxide poisoning resemble the u, with headaches, dizziness or nausea. If you have these signs, the heater may not be working properly. Get fresh air at once! Have heater serviced. Some people are more affected by carbon monoxide than others. These include pregnant women, people with heart or lung disease or anemia, those under the inuence of alcohol and those at high altitudes.

NATURAL GAS: Natural gas is odorless. An odor-making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas can fade. Gas may be present even though no odor exists.

WARNING: Any change to

this heater or its controls can

be dangerous.

WARNING: Do not use any accessories not approved for use with this heater.

WARNING: Carefully supervise young children when they are in the room with the heater.

WARNING: Make sure grill guard is in place before running

heater.

WARNING: Due to high temperatures, the appliance should

be located out of trafc and away

from furniture and draperies.

WARNING: Heater becomes

very hot when running. Keep children and adults away from

hot surfaces to avoid burns or

clothing ignition. Heater will remain hot for a time after shutoff.

Allow surfaces to cool before

touching.

WARNING: Do not place

clothing or other flammable

material on or near the appli-

ance. Never place any objects

in the heater.

www.usaprocom.com

3200048-01D

SAFETY

1. Heaters with a maximum input over 6,000 Btu/Hr shall not be installed in a bathroom. Heaters with a maximum input over 10,000 Btu/Hr shall not be installed in a bedroom.

2. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, pages 7 and 8. If heater keeps shutting off, see Troubleshooting, page 20.

3. Keep all air openings in front and bottom of heater clear and free of debris. This will ensure enough air for proper combustion.

4. If heater shuts off, do not relight until you have provided fresh, outside air. If heater keeps shutting off, have it serviced.

5. Do not run heater:

• Where ammable liquids or vapors are

used or stored.

• Under dusty conditions.

6. Always run heater with control knob at ON, LOW or HIGH locked positions. Never set control knob between locked positions. Poor combustion and higher levels of carbon monoxide may result.

7. Before using furniture polish, wax, carpet cleaner, or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls or furniture.

8. Do not use heater if any part has been under water. Immediately call a qualied service technician to inspect the room heater and to replace any part of the control system and any gas control which has been under water.

9. Turn off heater and let cool before servicing. Only a qualied service person should service and repair heater.

10. Operating heater above elevations of 4,500 feet could cause pilot outage.

SPECIFICATIONS

MODEL MN060HPA MN100HPA MN100TPA

Ignition Piezo Piezo Piezo

Gas Type Natural Gas Natural Gas Natural Gas

BTU (available) 6,000 5,500/10,000 10,000

Pressure Regulator Setting 6" W.C. 6" W.C. 6" W.C.

Inlet Gas Pressure* (inches of water)

Heater Weight 12 lbs 13 lbs 14 lbs

Shipping Weight 15 lbs 16 lbs 17 lbs

Heater Dimensions (HxWxD) 19 1/8" × 14 1/8" × 6 3/8"

Carton Dimensions (HxWxD) 22" × 16 3/4" × 8 1/8"

Note: Dimensions listed are outer most points on the heater (includes control knobs and grill).

* For purposes of input adjustment.

Maximum 10.5" Maximum 10.5" Maximum 10.5"

Minimum 7" Minimum 7" Minimum 7"

www.usaprocom.com

200048-01D4

PRODUCT IDENTIFICATION

Ignitor Button

Front Panel

Heater Cabinet

Figure 1 - Vent-Free Gas Heater

QUALIFIED INSTALLING AGENCY

Only a qualied agency should install and replace gas piping, gas utilization equipment or accessories, and repair and equipment servicing. The term “qualied agency” means any individual, rm, corporation, or company that either in person or through a representative is engaged in and is responsible for:

Control Knob

Grill

Burner

a) Installing, testing, or replacing gas piping

or

b) Connecting, installing, testing, repairing,

or servicing equipment; that is experienced in such work; that is familiar with all precautions required; and that has complied with all the requirement of the authority having jurisdiction.

PRODUCT FEATURES

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS/pilot shuts off the heater if there is not enough fresh air.

PIEZO IGNITION SYSTEM

This heater is equipped with a piezo ignitor. this system requires no matches, batteries, or other sources to light heater.

www.usaprocom.com

THERMOSTATIC CONTROL

(Thermostat Models Only)

These heaters have a control valve with a thermostat sensing bulb. This results in the greatest heater comfort and may result in lower gas bills.

5200048-01D

LOCAL CODES

Install and use heater with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code, ANSI Z223.1/NFPA 54*.

*Available from:

American National Standards Institute, Inc.

25 West 43rd Street

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02269-9101

UNPACKING

1. Remove heater from carton.

2. Remove all protective packaging applied to heater for shipping

WATER VAPOR: A BY-PRODUCT OF

UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one (1) ounce (30 mL) of water for every 1,000 BTUs (0.3 KWs) of gas input per hour. Unvented room heaters are recommended as supplemental heat (a room) rather than a primary heat source (an entire house). In most supplemental heat applications, the water vapor does not create a problem. In most applications, the water vapor enhances the low humidity atmosphere experienced during cold weather.

State of Massachusetts: The installation must be made by a licensed plumber or gas tter in the Commonwealth of Massachusetts.

Sellers of unvented propane or natural gas-red supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

In the State of Massachusetts the gas cock must be a T-handle type. The State of Massachusetts requires that a exible appliance connector cannot exceed three feet in length.

3. Check heater for any shipping damage. If heater is damaged, promptly inform dealer where you bought heater.

The following steps will help ensure that water vapor does not become a problem.

1. Be sure the heater is sized properly for the application, including ample combustion air and circulation air.

2. If high humidity is experienced, a dehumidier may be used to help lower the water vapor content of the air.

3. Do not use an unvented room heater as the primary heat source.

www.usaprocom.com

200048-01D6

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall

not be installed in a conned

space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other

fuel-burning appliances in your

home.

Today’s homes are built more energy efcient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Home owners weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, home owners want their homes as airtight as possible. While it is good to make your home energy efcient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation. Exhaust fans, replaces, clothes dryers and fuel burning appliances draw air from the house to operate. You must provide adequate fresh air for these appliances. This will insure proper venting of vented fuel-burning appliances.

WARNING: This heater shall

not be installed in a room or

space unless the required vol-

ume of indoor combustion air is provided by the method described in the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or

applicable local codes.

WARNING: If the area in which

the heater may be operated does

not meet the required volume for

indoor combustion air, combustion and ventilation air shall be provided by one of the methods described in the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code,

or applicable local codes.

www.usaprocom.com

7200048-01D

AIR FOR COMBUSTION AND VENTILATION

Ventilation

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconned space. When ventilating to an adjoining unconned space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the oor on the wall connecting the two spaces (see options 1 and 2, Figure 2). You can also remove door into adjoining room (see option 3, Figure 2). Follow the National Fuel Gas Code, ANSI

Z223.1/NFPA 54, Air for Combustion and Ventilation for required size of ventilation

grills or ducts.

12"

Ventilation Grills

Into Adjoining Room,

Grills into Adjoining

Room,

Option 1

Or

Remove Door into Adjoining

Room,

Option 3

12"

Option 2

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the oor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation for required size

of ventilation grills or ducts. IMPORTANT: Do not provide openings

for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent. Rework worksheet, adding the space of the adjoining unconned space. The combined spaces must have enough fresh air to supply all appliances in both spaces.

Ventilated Attic

Crawl Space

Ventilated

To Attic

To

Crawl

Space

Outlet Air

Inlet Air

Outlet Air

Inlet Air

Figure 3 - Ventilation Air from Outdoors

Figure 2 - Ventilation Air from Inside

Building

www.usaprocom.com

200048-01D8

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may

run system’s circulating blower

while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

CAUTION: When installing

heater in a home garage

• heater pilot and burner must be at least 18" above oor

• locate heater where moving vehicle will not hit it

WARNING: A qualied service person must install heater. Follow all local codes.

WARNING: Never install the heater

• Models MN100HPA or

MN100TPA in a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other ammable objects are less than 36" from

the front, top, or sides of the heater

• in high trafc areas

• in windy or drafty areas

WARNING: MODEL

MN060HPA ONLY! When

installed in a bathroom, do not use ammable products such

as aerosol hair spray or any

product that contains ammable

vapors. Keep towels and other

ammable materials away from

heater.

CAUTION: This heater creates warm air currents. These currents move heat to wall surfaces next to heater. Installing heater next to vinyl or cloth wall coverings or operating heater

where impurities (such as tobacco smoke, aromatic candles, cleaning uids, oil or kerosene lamps, etc.) in the air exist, may

cause walls to discolor.

IMPORTANT: Vent-free heaters add moisture to the air. Although this is benecial, installing heater in rooms without enough ventilation air may cause mildew to form too much moisture. See Air for Combustion and Ventilation, pages 7 and 8.

CHECK GAS TYPE

Be sure your gas supply is right for your heater. Otherwise, call dealer where you bought the heater for proper type heater.

CLEARANCES TO

COMBUSTIBLES

WARNING: Maintain the minimum clearances shown in Figure 4, page 10. If you can, provide

greater clearances from oor,

ceiling, and joining wall.

www.usaprocom.com

9200048-01D

INSTALLATION

CEILING

36"

8"

Minimum From Sides of Heater

Left Side

2" Minimum to Top Surface of Carpeting, Tile or Other Combustible Material

FLOOR

Minimum

Right Side

Figure 4 - Mounting Clearances as

Viewed From Front of Heater

LOCATING HEATER

This heater is designed to be mounted on a wall. You can locate heater on the oor, away from a wall. An optional oor mounting stand is needed. See Accessories, page 23.

For convenience and efciency, install heater:

1. Where there is easy access for operation, inspection, and service.

2. In the coldest part of room.

An optional fan kit is available from your dealer See Accessories, page 23. If planning to use fan, locate heater near an electrical outlet.

FASTENING HEATER TO WALL

The mounting bracket is located on back panel of heater (see Figure 5). It has been taped there for shipping. Remove mounting bracket from back panel.

Mounting Bracket

Removing Front Panel of Heater

1. Remove two screws near bottom corners of lower front panel.

2. Pull bottom of lower front panel forward, then down (see Figure 6).

Figure 6 - Removing Front Panel Of

Heater

Methods For Attaching Mounting

Bracket To Wall

Use only the last hole on each end of mounting bracket to attach bracket to wall. Attach mounting bracket to a wall only in one of two ways:

1. Attaching to wall stud: This method pro- vides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

2. Attaching to wall anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Mounting Bracket

Figure 5 - Mounting Bracket Location

www.usaprocom.com

200048-01D10

INSTALLATION

Marking Screw Locations

1. Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

WARNING: Maintain minimum clearances shown in Figure 4, page 10. If you can, provide

greater clearances from oor and

joining wall.

2. Mark screw locations on wall (see Figure

7). Note: Mark only last hole on each end

of mounting bracket. Insert mounting screws through these holes only.

3. Remove tape and mounting bracket from wall.

3

/4"

6

Min.

Only Insert Mounting

Screws Through Last

Adjoining Wall

121/8"

Hole On Each End

Floor

141/2"

Min.

1. Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1" deep.

2. Fold wall anchor as shown in Figure 8.

3. Insert wall anchor (wings rst) into hole. Tap anchor ush to wall.

4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 9).

IMPORTANT: Do not hammer anchor key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.

5. Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors.

6. Insert mounting screws through bracket and into wall anchors.

7. Tighten screws until mounting bracket is rmly fastened to wall.

Figure 8 - Folding Anchor

Figure 7 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hardware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs:

1. Drill holes at marked locations using 9/64" drill bit.

2. Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3. Insert mounting screws through bracket and into wall studs.

4. Tighten screws until mounting bracket is rmly fastened to wall studs.

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry):

www.usaprocom.com

Figure 9 - Popping Open Anchor Wings

Placing Heater On Mounting

1. Locate two horizontal slots on back panel of heater (see Figure 10).

2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Stand-Out Tab

Figure 10 - Mounting Heater Onto

For Thin Walls

Bracket

Horizontal Slots

Mounting Bracket (attached to wall)

Mounting Bracket

11200048-01D

INSTALLATION

Installing Bottom Mounting Bracket

1. Install bottom bracket to heater bottom with two screws. It may be more convenient to remove heater from wall bracket to attach.

2. Place heater on wall mounting bracket.

3. Mark screw locations on wall.

4. Remove heater from mounting bracket.

5. If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 under Attaching To Wall Anchor Method, page 11. If installing bottom mounting screw into wall stud, drill holes at marked locations using 9/64" drill bit.

6. Replace heater onto mounting bracket.

7. Place spacers between bottom mounting holes and wall anchor or drilled hole.

8. Hold spacer in place with one hand. With other hand, insert mounting screw though bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

CONNECTING TO GAS SUPPLY

WARNING: A qualied service technician must connect heater to gas supply. Follow all local codes.

WARNING: This appliance

requires a 3/8" NPT (National Pipe Thread) inlet connection to

the pressure regulator.

9. Tighten both screws until heater is rmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks.

Front View

Wall

Heater

Spacer

Side View

Figure 11 - Installing Bottom Mounting

Screws

CAUTION: Use only new,

black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check

your local codes. Use pipe of

1/2" diameter or greater to allow

proper gas volume to heater. If pipe is too small, undue loss of pressure will occur.

WARNING: Never connect

heater to private (non-utility)

gas wells. This gas is commonly

known as wellhead gas.

WARNING: Do not over-

tighten gas connections.

www.usaprocom.com

CAUTION: Check your gas

line pressure before connect-

ing heater to gas line. Gas line

pressure must be no greater than

10.5" of water. If gas line pres-

sure is higher, heater regulator damage could occur.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting

into gas piping and/or ttings.

200048-01D12

INSTALLATION

CAUTION: Use pipe joint sealant that is resistant to natural gas.

Before installing heater, make sure you have the items listed below:

• external regulator for propane/LP unit only (supplied by installer)

• piping (check local codes)

• sealant (resistant to natural gas and propane/LP gas)

• equipment shutoff valve*

• test gauge connection*

• sediment trap

• tee joint

• pipe wrench

• exible gas hose (check local codes)

* A CSA design-certied equipment shutoff valve with 1/8” NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design certied equipment shutoff valve from your dealer.

Pressure Regulator

Typical Inlet Pipe Diameters

Models up to 20,000 BTU/hr use 3/8" black iron pipe or greater. Models 25,000 BTU/hr and higher use 1/2" black iron pipe or greater. Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 12).

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves.

Install sediment trap in supply line as shown in Figure 12. Place sediment trap where it is within reach for cleaning. Place sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

Ground Joint Union

Tee Joint

Reducer

Test Gauge Connection*

Sediment

Trap

* Purchase the optional CSA design-certied equipment shutoff valve from your dealer.

Bushing to 1/8" NPT

1/8" NPT Plug Tap

Tee Joint

Pipe Nipple

Gap

Figure 12 - Gas Connection

www.usaprocom.com

3" Minimum

3/8" NPT Pipe Nipple

Equipment Shutoff Valve

From Gas Meter

(7" W.C. to

10.5" W.C. Pressure)

13200048-01D

INSTALLATION

CHECKING GAS CONNECTIONS

WARNING: Test all gas piping

and connections for leaks after

installing or servicing. Correct

all leaks at once.

WARNING: Never use an open

ame to check for a leak. Apply a noncorrosive leak detection uid to all joints. If bubbles form, there is a leak. Correct all leaks

at once.

PRESSURE TESTING GAS SUPPLY

Test Pressures In Excess Of 1/2 PSIG

1. Disconnect heater with its appliance main

2. Cap off open end of gas pipe where equip-

3. Pressurize supply piping system by either

4. Check all joints of gas supply piping sys-

5. Correct all leaks at once.

6. Reconnect heater and equipment shutoff

Equipment Shutoff Valve

PIPING SYSTEM

(3.5 kPa)

gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 PSIG will damage heater regulator.

ment shutoff valve was connected.

opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air.

tem. Apply a noncorrosive leak detection uid to all joints. If bubbles form, there may be a leak.

valve to gas supply. Check reconnected ttings for leaks.

Open

Test Pressures Equal To or Less Than

1. Close equipment shutoff valve (see Fig-

2. Pressurize supply piping system by either

3. Check all joints from gas meter to equip-

4. Correct all leaks at once.

PRESSURE TESTING HEATER GAS

1. Open equipment shutoff valve (see Fig-

2. Open main gas valve located on or near

3. Make sure control knob of heater is in the

4. Check all joints from equipment shutoff

5. Correct all leaks at once.

6. Light heater (see Operation, page 15).

7. Turn off heater (see To Turn Off Gas Ap-

8. Replace lower front panel.

External Regulator Supplied by Gas Supplier

1/2 PSIG (3.5 kPa)

ure 13).

opening main gas valve located on or near gas meter or using compressed air.

ment shutoff valve (see Figure 14). Apply a noncorrosive leak detection uid to all joints. If bubbles form, there is a leak.

CONNECTIONS

ure 13).

gas meter.

OFF position.

valve to control valve (see Figure 14). Apply a noncorrosive leak detection uid to all joints. Bubbles forming show a leak.

Check all other internal joints for leaks.

pliance, page 17).

Gas Valve

Gas Meter

Closed

Figure 13 - Equipment Shutoff Valve

www.usaprocom.com

Equipment Shutoff Valve

Figure 14 - Natural Gas Supply

200048-01D14

OPERATION

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a re or explosion may result causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

B. BEFORE LIGHTING smell all around the

appliance area for gas. Be sure to smell

next to the oor because some gas is heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

MANUAL CONTROL MODELS

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. Check that gas supply to heater is on.

3. Push in gas control knob slightly and turn clockwise to the OFF position.

Note: Knob cannot be turned from PILOT to OFF unless knob is pushed in slightly. Do not force.

4. Wait ve (5) minutes to clear out any gas. Then smell for gas, including near the oor. If you smell gas, STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step.

5. Push in gas control knob slightly and turn counterclockwise to "PILOT/IGN" and press for ve (5) seconds

Note: The rst time that the heater is oper-

ated after connecting the gas supply, the control knob should be pressed for about thirty (30) seconds. This will allow air to bleed from the gas system.

6. With control knob pressed in, push down and release the ignitor button. This will light pilot. If needed, keep pressing ignitor button until pilot lights.

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier,

call the re department.

C. Use only your hand to push in or turn

the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualied

service technician. Force or attempted

repair may result in a re or explosion.

D. Do not use this appliance if any part

has been under water. Immediately call a qualied service technician to inspect

the appliance and to replace any part of the control system and any gas control

which has been under water.

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. If control knob does not pop up when released, contact a qualied service technician or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3

through 7. This heater has a safety interlock system. Wait one (1) minute before lighting pilot again.

Model MN060HPA

OFF

PILOT/IGN

Ignitor Button

ON

Control Knob

Model MN100HPA

OFF

PILOT/IGN

Ignitor Button

HIGH

LOW

Control Knob

Figure 15 - Control Knob in the OFF

Position

www.usaprocom.com

15200048-01D

Control Knob

OFF

PILOT/IGN

ON

Control Knob

HIGH

LOW

OPERATION

8. To select the desired heating level, partially press down the control knob slightly and turn counterclockwise . Release downward pressure on the knob while continuing to turn until the knob locks at the desired setting. The main burner should light. Set control knob to the desired heating position.

Note: Both HIGH and LOW are locked

positions. You must press in the control knob before turning it from these positions.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

Thermocouple

1. STOP! Read the safety information on page 15.

2. Make sure equipment shutoff valve is fully open.

3. Turn control knob clockwise to the OFF position.

4. Wait ve (5) minutes to clear out any air. Then smell for gas, including near the oor. If you smell gas, STOP! Follow "B" in the safety information, page 15. If you do not smell gas, go to the next step.

5. Turn control knob counterclockwise to the PILOT position. Press in control knob for ve (5) seconds (see Figure 18).

Note: The rst time that the heater is oper-

ated after connecting the gas supply,the control knob should be pressed for about thirty (30) seconds. This will allow air to bleed from the gas system. If pilot does not stay lit, refer to Troubleshooting, pages

20 though 22. Also contact a qualied

Ignitor Electrode

Pilot Burner

Figure 16 - Pilot

LIGHTING INSTRUCTIONS

THERMOSTAT MODELS

www.usaprocom.com

MN060HPA

OFF

PILOT/IGN

OFF

ON

MN100HPA

OFF

PILOT/IGN

OFF

PILOT/IGN

OFF

PILOT/IGN

LOW

HIGH

LOW

OFF

Figure 17 - Burner Patterns

service technician or gas supplier for repairs. Until repairs are made, light pilot with match.

• If control knob does not pop up when released, contact a qualified service technician or gas supplier for repairs.

6. With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. The pilot can be seen through the grill. If needed, keep pressing ignitor button until pilot lights.

LO

PILOT

OFF

HI

Ignitor Button

Control Knob

Figure 18 - Control Knob in the OFF

Position

200048-01D16

OPERATION

Note: If pilot does not stay lit, refer to Troubleshooting, pages 20 though 22.

Also contact a qualied service technician

or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure.

7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. If control knob does not pop up when released, contact a qualied service technician or gas supplier for repairs.

Note: If pilot goes out, repeat steps 3

through 7. This heater has a safety interlock system. Wait one (1) minute before lighting pilot again.

8. Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between HI and LO.

CAUTION: Do not try to ad-

just heating levels by using the

equipment shutoff valve.

THERMOSTAT CONTROL OPERATION

The thermostatic control used on these models differ from standard thermostats. Standard thermostats simply turn the burner on and off. The thermostat used on this heater senses the room temperature. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any comfort level between HI and LO.

Thermocouple

Ignitor Electrode

Pilot Burner

Figure 19 - Pilot

Control Knob

OFF

HI

PILOT

OFF

HI

PILOT

LO

MN100TPA

LOW HIGH

OFF

Figure 20 - Burner Patterns

Note: The thermostat sensing bulb measures the temperature of air near the heater cabinet. This may not always agree with room temperature (depending on housing construction, installation location, room size, open air temperatures, etc.) Frequent use of your heater will let you determine your own comfort levels.

ALL MODELS

TO TURN OFF GAS TO APPLIANCE

Shutting Off Heater

Turn control knob clockwise to the OFF position.

MANUAL LIGHTING PROCEDURE

1. Remove lower front panel.

2. Follow steps 1 through 5 under Lighting Instructions, page 15 or 16.

3. With control knob pressed in, strike match. Hold match to pilot until pilot lights.

www.usaprocom.com

Shutting Off Burner Only

(pilot stays lit)

Turn control knob clockwise to the PILOT position.

4. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Follow step 8 under Lighting Instructions, page 15 or 16.

5. Replace lower front panel.

17200048-01D

INSPECTING HEATER

IMPORTANT: Owner’s should check pilot ame pattern and burner ame pattern often. Incorrect ame patterns indicate the need for cleaning (see Care and Maintenance,

page 19) or service.

WARNING: Only a qualied service person should service and repair heater. This includes maintenance requiring replacement or alteration of components.

PILOT FLAME PATTERN

Figure 21 shows a correct pilot ame pattern. Figure 22 shows an incorrect pilot ame pattern. The incorrect pilot ame is not touching the thermocouple. This will cause the thermocouple to cool, which shuts the heater off.

If pilot ame pattern is incorrect, as shown in Figure 22

• turn heater off (see To Turn Off Gas to Ap- pliance, page 17)

• see Troubleshooting pages 20 through 22.

Notice: Do not mistake orange ames with yellow tipping. Dirt or other ne particles enter

the heater and burn causing brief patches of

orange ame.

Figure 21 - Correct Pilot Flame Pattern

WARNING: If yellow tipping

occurs, your heater could pro-

duce increased levels of carbon monoxide. If the burner ame

pattern shows yellow tipping,

follow instructions below.

Figure 22 - Incorrect Pilot Flame Pattern

BURNER FLAME PATTERN

Figure 23 shows a correct burner ame pattern. Figure 24 shows an incorrect burner ame pattern. The incorrect burner ame pattern shows yellow tipping of the ame. It also shows the ame higher than 1/2 the heat shield height.

If burner ame pattern is incorrect, as shown in Figure 24

• turn heater off (see To Turn Off Gas to Ap- pliance, page 17)

• see Troubleshooting pages 20 through 22.

www.usaprocom.com

Figure 23 - Correct Burner Flame Pattern

Figure 24 - Incorrect Burner Flame

Pattern

200048-01D18

CARE AND MAINTENANCE

WARNING: Turn off heater and let cool before servicing.

CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualied service techni-

cian. Heater may need more frequent cleaning due to excessive lint

from carpeting, bedding material, pet hair, etc.

WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.

ODS/PILOT AND BURNER

Use a vacuum cleaner, pressurized air, or a small, soft bristled brush to clean.

BURNER PILOT AIR INLET

The primary air inlet hole allows the proper amount of air to mix with the gas. This provides a clean burning ame. Keep this hole clear of dust, dirt and lint. Clean this air inlet hole prior to each heating season. A blocked air hole will create soot. We recommend that you clean the unit every three months during operation and have heater inspected yearly by a qualied service person.

We also recommend that you keep the burner tube and pilot assembly clean and free of dust and dirt. To clean these parts we recommend using compressed air no greater than 30 PSl. Your local computer store, hardware store, or home center may carry compressed air in a can. You can use a vacuum cleaner in the blow position. If using compressed air in a can, please follow the directions on the can. If you don’t follow directions on the can, you could damage the pilot assembly.

1. Shut off the unit, including the pilot. Allow the unit to cool for at least thirty minutes.

2. Inspect burner and pilot for dust and dirt.

Air Passageways

Use pressurized air to clean.

Use a soft cloth dampened with a mild soap and water mixture. Wipe the cabinet to remove dust.

3. Blow air across the ports/slots and holes in the burner.

4. Never insert objects into the pilot tube.

Clean the pilot assembly also. A yellow tip on the pilot ame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet about 2" from where the pilot ame comes out of the pilot assembly (see Figure 25). With the unit off, lightly blow air through the air inlet. You may blow through a drinking straw if compressed air is not available.

Pilot Assembly

Pilot Air Inlet Hole

Figure 25 - Pilot Inlet Air Hole

CABINET

Exterior

www.usaprocom.com

19200048-01D

TROUBLESHOOTING

WARNING: If you smell gas:

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

WARNING: Only a qualied service technician should service and repair heater. Make sure that power is turned off before proceeding. Turn off and let cool before servicing.

CAUTION: Never use a wire, needle, or similar object to clean

ODS/pilot. This can damage ODS/ pilot unit.

IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes. These fumes may mix with combustion air and create odors.

Note: All troubleshooting items are listed in order of operation.

Problem Possible Cause Corrective Action

When ignitor button is pressed in, there is no spark at ODS/pilot.

When ignitor button is pressed in there is a spark at ODS/pilot but no ignition.

1. Ignitor electrode is positioned wrong. Ignitor electrode is broken.

2. Ignitor electrode is not connected to ignitor cable.

3. Ignitor cable is pinched or wet.

4 Broken ignitor cable.

5. Bad piezo ignitor.

1. Gas supply is turned off or equipment shutoff valve is closed.

2. Control knob not fully pressed in while pressing ignitor button.

3. Air in gas lines when installed.

4. ODS / pilot is clogged.

5. Incorrect inlet gas pressure or inlet regulator is damaged.

6. Control knob not in PILOT position.

1. Replace pilot assembly.

2. Replace ignitor cable.

3. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry.

4. Replace ignitor cable.

5. Replace piezo ignitor.

1. Turn on gas supply or open equipment shutoff valve.

2. Fully press in control knob while pressing ignitor button.

3. Continue holding down control knob. Repeat igniting operation until air is removed.

4.

Clean ODS/pilot (see Care and Maintenance, page 19) or

replace ODS/pilot assembly.

5. Check inlet gas pressure or replace inlet gas regulator.

6. Turn control knob to PILOT position.

www.usaprocom.com

200048-01D20

TROUBLESHOOTING

Problem Possible Cause Corrective Action

ODS/pilot lights but ame goes out when control knob is released.

Burner(s) does not light after ODS/pilot is lit.

Delayed ignition of burner(s).

Burner backring during combustion.

Burner plaque(s) does not glow.

Gas odor during combustion.

1. Control knob is not fully pressed in.

2. Control knob is not pressed in long enough.

3. Equipment shutoff valve is not fully open.

4. Thermocouple connection is loose at control valve.

5. Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot ame to go out. This problem could be caused by one or both of the following:

A) Low gas pressure B) Dirty or partially clogged

ODS/pilot

6. Thermocouple damaged.

7. Control valve damaged.

1. Burner orice is clogged.

2. Inlet gas pressure is too low.

1. Manifold pressure is too low.

2. Burner orice is clogged.

1. Burner orice is clogged or damaged.

2. Burner is damaged.

3. Gas regulator is damaged.

1. Plaque is damaged.

2. Inlet gas pressure is too low.

3. Control knob set between locked positions.

1. Foreign matter between control valve and burner.

2. Gas leak. (See Warning Statement at top of page 20).

1. Press in control knob fully.

2. After ODS/pilot lights, keep control knob pressed in 30 seconds.

3. Fully open equipment shutoff valve.

4. Hand tighten until snug, and then tighten 1/4 turn more.

5. A) Contact local natural or propane/LP gas company

B) Clean ODS/pilot (see

Care and Maintenance, page 19) or replace ODS/ pilot assembly

6. Replace thermocouple

7. Replace control valve.

1. Clean burner orifice (see Care and Maintenance, page 19.

2. Contact local gas supplier.

1. Contact local gas supplier.

2. Clean burner (see Care and Maintenance, page 19) or replace burner orice.

1. Clean burner orifice (see Care and Maintenance, page 19).

2. Replace burner.

3. Replace gas regulator.

1. Replace burner.

2. Contact local gas company.

3. Turn control knob until it locks at desired setting.

1. Take apart gas tubing and remove foreign matter.

2. Locate and correct all leaks (see Checking Gas Connec- tions, page 14).

www.usaprocom.com

21200048-01D

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Slight smoke or odor during initial operation.

Heater produces a clicking/ticking noise just after burner is lit or shut off.

White powder residue forming within burner box or on adjacent walls or furniture.

Heater produces unwanted odors.

Heater shuts off in use (ODS operates).

Gas odor exists even when control knob is in OFF position.

Moisture/condensation noticed on windows.

1. Residues from manufacturing process.

1. Metal is expanding while heating or contracting while cooling.

1. When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue.

1. Heater is burning vapors from paint, hair spray, glues, etc. See IMPORTANT statement, page 20.

2. Gas leak. See Warning State- ment at the top of page 20.

3. Low fuel supply (propane/LP gas only).

1. Not enough fresh air is available.

2. Low line pressure.

3. ODS/pilot is partially clogged.

1. Gas leak. See Warning Statement at top of page 20.

2. Control valve is defective.

1. Not enough combustion/ ventilation air.

1. Problem will stop after a few hours of operation.

1. This is common with most heaters. If noise is excessive, contact qualied service technician.

1. Turn heater off when using furniture polish, wax, carpet cleaner or similar products.

1. Ventilate room. Stop using odor causing products while heater is running.

2. Locate and correct all leaks (see Checking Gas Connec- tions, page 14).

3. Rell supply tank (Propane/ LP models).

1. Open window and/or door for ventilation.

2. Contact local gas supplier.

3. Clean ODS/pilot (see Care and Maintenance, page 19).

1. Locate and correct all leaks (see Checking Gas Connec- tions, page 14).

2. Replace control valve.

1. Refer to Air for Combus- tion and Ventilation requirements, page 7.

www.usaprocom.com

200048-01D22

REPLACEMENT PARTS

Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement parts, call Customer Service toll free at 1-866-573-0674 for referral information.

When calling Customer Service or your dealer, have ready:

• Your name

• Your address

• Model and serial number of your heater

• How heater was malfunctioning

• Type of gas used (Propane/LP or Natural gas/NG)

• Purchase date

Usually, we will ask you to return the defective part to the factory

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s) call Customer Service toll free at 1-866-573-0674 for referral information.

When calling Customer Service have ready:

• Model number of your heater

• The replacement part number

ACCESSORIES

Purchase these heater accessories from your local dealer. If they can not supply these accessories, contact ProCom Heating, Inc. at 1-866-573-0674 for information.

EQUIPMENT SHUTOFF VALVE

For all models. Equipment shutoff valve with 1/8" NPT tap.

FLOOR MOUNTING STAND

PF09B For locating heater on the oor, away from a wall. Complete

installation instructions provided with oor mounting stand.

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• replace will not produce specied heat

• propane/LP gas supply might be low (propane/LP units only)

You may feel your gas pressure is too low. If so, contact your local gas supplier.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. If so, contact ProCom Heating, Inc. at 1-866-573-0674.

When calling, please have your model and serial numbers of your heater ready.

www.usaprocom.com

23200048-01D

13

PARTS

MODEL MN060HPA

12

www.usaprocom.com

200048-01D24

PARTS

MODEL MN060HPA

This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 23 of this manual.

ITEM PART # DESCRIPTION QTY

1 **MB10008 Cabinet Assembly 1

2 MB09003 Lower Front Panel 1

3 **ML006-02 Reector Unit 1

4 **MB19007 Burner Assembly 1

5 ND1206-600 ODS Pilot 1

5-1 ND0803-6 Thermocouple 1

5-2 ND0807 Ignitor Electrode 1

6 **ML026-03 ODS Mounting Bracket 1

7 **ML069-02 Self Tapping Screws 10

8 NV2020-12 Control Valve 1

9 ML073-02 Ignitor Cable 1

10 ML029-01 Control Valve Fixed Nut 1

11 **MB40033 Main Inlet Tube Assembly 1

12 ML083-03 Ignitor 1

13 **ML105-05 ODS Deector 1

14 **ML090-01 Injector 1

15 ML031-03 Control Knob 1

16 **RV81FI-6 Pressure Regulator 1

17 **ML129-02 Regulator Mounting Bracket 1

18 **ML079-01 Self Locking Screws 4

19 **ML119-01 Pressure Tap 1

20 MB29003 Grill Guard 1

21 161132-01 Mounting Bracket 1

PARTS AVAILABLE - NOT SHOWN

161607-01 Hardware Package 1

**Not a eld replaceable part.

www.usaprocom.com

25200048-01D

24

PARTS

MODEL MN100HPA

www.usaprocom.com

200048-01D26

PARTS

MODEL MN100HPA

This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 23 of this manual.

ITEM PART # DESCRIPTION QTY

1 **MB10008 Cabinet Assembly 1

2 MB09003 Lower Front Panel 1

3 **ML006-01 Reector Unit 1

4 **MB19005 Burner Assembly 1

5 ND1206-600 ODS Pilot 1

5-1 ND0803-6 Thermocouple 1

5-2 ND0807 Ignitor Electrode 1

6 ML026-02 ODS Mounting Bracket 1

7 **ML069-02 Self Tapping Screws 10

8 NV2020-13 Control Valve 1

9 ML073-01 Ignitor Cable 1

10 ML029-01 Control Valve Fixed Nut 1

11 **MB40033 Main Inlet Tube Assembly 1

12 **MB40034 ODS Gas Line Assembly 1

13 **MB40035 Burner Gas Line Assembly A 1

14 **MB40036 Burner Gas Line Assembly B 1

15 **ML090-03 Injector 2

16 ML031-03 Control Knob 1

17 **RV81FI-6 Pressure Regulator 1

18 **ML129-02 Regulator Mounting Bracket 1

19 **ML079-01 Self Locking Screws 4

20 **ML119-01 Pressure Tap 1

21 MB29003 Grill Guard 1

22 161132-01 Mounting Bracket 1

23 ML083-03 Ignitor 1

24 **ML105-05 ODS Deector 1

PARTS AVAILABLE - NOT SHOWN

161607-01 Hardware Package 1

**Not a eld replaceable part.

www.usaprocom.com

27200048-01D

25

PARTS

MODEL MN100TPA

24

www.usaprocom.com

200048-01D28

PARTS

MODEL MN100TPA

This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 23 of this manual.

ITEM PART # DESCRIPTION QTY

1 **MB10007 Cabinet Assembly 1

2 MB09003 Lower Front Panel 1

3 **ML006-01 Reector Unit 1

4 **MB19005 Burner Assembly 1

5 ND1206-600 ODS Pilot 1

5-1 ND0803-6 Thermocouple 1

5-2 ND0807 Ignitor Electrode 1

6 **ML026-02 ODS Mounting Bracket 1

7 **ML069-02 Self Tapping Screws 10

8 **845-4.8 x 60Z Screws 1

9 161130-01 Thermostat Valve 1

10 **ML111-02A Thermostat Valve Bracket 1

11 **ML056-03 "T" Joint 1

12 **MB40037 Main Inlet Tube Assembly 1

13 **MB40039 ODS Gas Line Assembly 1

14 **MB40038 Main Outlet Tube Assembly 1

15 **MB40040 Burner Gas Line Assembly A 1

16 **ML090-03 Injector 2

17 **MB40041 Burner Gas Line Assembly B 1

18 **RV81FI-6 Pressure Regulator 1

19 **ML129-02 Regulator Mounting Bracket 1

20 **ML079-01 Self Locking Screws 4

21 MB29003 Grill Guard 1

22 161132-01 Mounting Bracket 1

23 ML083-03 Ignitor 1

24 **ML105-05 ODS Deector 1

25 ML073-01 Ignitor Cable 1

PARTS AVAILABLE - NOT SHOWN

161607-01 Hardware Package 1

**Not a eld replaceable part.

www.usaprocom.com

29200048-01D

NOTES

________________________________________________________________________

www.usaprocom.com

200048-01D30

NOTES

________________________________________________________________________

www.usaprocom.com

31200048-01D

WARRANTY

KEEP THIS WARRANTY

Model _______________________________

Serial No. ____________________________

Date Purchased _______________________

Keep receipt for warranty verication.

REGISTER YOUR PRODUCT AT WWW.USAPROCOM.COM

IMPORTANT: We urge you to register your product within 10 days of date of installation, complete

with entire serial number which can be found on the rating plate. Please ll out the warranty information above for your personal records. Retain this manual for future reference.

Always specify model and serial numbers when communicating with customer service.

We reserve the right to amend these specications at any time without notice. The only warranty applicable is our standard written warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

ProCom Heating, Inc. warrants this product to be free from defects in materials and components for ONE (1) year from the date of rst purchase, provided that the product has been properly installed by a qualied installer in accordance with all local codes and instructions furnished with the unit, operated and maintained in accordance with all applicable instructions. To make a claim under this warranty, the Bill of Sale or cancelled check must be presented.

RESPONSIBILITY OF OWNER

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this heater to proper operating condition. Warranty part(s) MUST be obtained through ProCom Heating, Inc. who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.

IMPORTANT: The heater MUST be installed by a qualied installer in accordance with all local codes

and instructions furnished with the unit or the warranty is voided.

WHAT IS NOT COVERED

This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT, THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES. INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO ONE (1) YEAR ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE. PROCOM HEATING, INC.'S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND PROCOM HEATING, INC. SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT. INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of accidental or consequential damages, the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specic legal right, and you may also have other rights that vary from state to state.

ProCom Heating, Inc. Bowling Green, KY 42101 www.usaprocom.com 1-866-573-0674

200048-01 Rev. D 01/17

Procom Heating MN100HPA, MN060HPA, MN100TPA User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

SAFETY

SPECIFICATIONS

PRODUCT IDENTIFICATION

QUALIFIED INSTALLING AGENCY

PRODUCT FEATURES

LOCAL CODES

UNPACKING

AIR FOR COMBUSTION AND VENTILATION

INSTALLATION

OPERATION

INSPECTING HEATER

CARE AND MAINTENANCE

TROUBLESHOOTING

REPLACEMENT PARTS

ACCESSORIES

SERVICE HINTS

TECHNICAL SERVICE

PARTS

WARRANTY