Procom V50TYLA-O, V50TYLA-DO, V50TYLAR-BC, V50TYLA-C, V50TYLA-BC User Manual

Installation Instructions and Homeowner’s Manual

WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

FLAMMABLE VAPORS OR LIQUIDS
IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE

INSTALLER: DO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER

FOR YOUR SAFETY

DO NOT STORE

OR USE GASOLINE OR OTHER

1

PC(220)-VCL100-01-0709

PLEASE READ THE INSTALLATION & OPERATION INSTRUCTIONS BEFORE

USING THIS APPLIANCE

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these

instructions may result in a possible electric shock, fire hazard and will void the warranty.

Important instructions ……………………………………………………………3

General…………………………………………………………………………….…3

Locating Your Electric Fireplace…………………………………… …………… 3

Clearance To Combustibles………………………………………… …………... 4

Electrical Connections…..……………………………………………… ………. 4

Electrical Specifications………………………………………… ……………..… 4

Service Instructions…………………………………………………………… … 4

Replacing Light Bulbs…………………………………… …………………………4

Glass Information……………………………………………… ………………… 5

Maintenance of Motors………………………………………… …………… … 5

Electrical Wiring Diagram……………………………………… ………………… 5

Operating Instructions…………………………………………………………… 6

On/Off Switch……………………………………………………………………. .. 6

Heater Control…………………………………………………………………… .. 6

Instructions for power………………………………………………………………. 6

Specifications………………………………………………………………….. …. 7

Replacement Parts Pictures…………………………………………………….. 8

Replacement Parts List (V50TYLA-O)…………………………………………… 9

Replacement Parts List (V50TYLA-C)……………………………………………10

Replacement Parts List (V50TYLA-DO)………………………………………… 11

Replacement Parts List (V50TYLA-BC)………………………………………… 12

Replacement Parts List (V50TYLAR-BC)……………………………………… 13

2

GENERAL

1.Read all instructions before using this

appliance.

2.This appliance is hot when in use. To avoid

burns, do not let bare skin touch hot surfaces.

Keep combustible materials, such as furniture,

pillows, bedding, papers, clothes, and curtains

at least 3 feet(1m.) from the front of this

appliance.

3.CAUTION: Extreme caution is necessary when

any heater is used by or near children or inva-

lids and whenever the heater is left Operating

and unattended.

4.Always unplug heater when not in use.

5.Do not operate any heater with a damaged

cord or plug or after the heater malfunctions,

has been dropped or damaged in any manner.

6.Any repairs to this appliance should be carried

out by a qualified service person.

7.Under no circumstances should this electric fire-

place be modified. Parts having to be removed

for servicing must be replaced prior to operat-

ing this electric fireplace again.

8.Do not use outdoors.

13.Do not insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause

electric shock, fire or damage to the appliance.

14.To prevent fire, do not block air intakes or exhaust

in any manner. Do not use on soft surfaces, such

as a bed, where openings may become blocked.

15.This appliance has hot and arcing or sparking parts

inside. Do not use it in areas where gasoline, paint,

or flammable liquids are used or stored. This elec-

tric fireplace should not be used as a drying rack

for clothing, Also, do not have Christmas stock-

ings or decorations hung on or near it.

16.Use this appliance only as described in this

manual. All other uses not recommended by the

manufacturer may cause fire, electric shock, or

injury.

17.Avoid the use of an extension cord because it may

overheat and cause a fire hazard. However if you

must use an extension cord, the cord shall be

2

1.0 mm

be a three wire cord with grounding type plug

and cord connector.

,1900 Watts. The extension cord must

18.SAVE THESE INSTRUCTIONS.

9.This heater is not intended for use in bathrooms,

laundry areas or similar indoor locations. Never

use this appliance near a bathtub or other wa-

ter container.

10.Do not run cord under carpeting. Do not cover

cord with throw rugs, runners or the like. Arrange

cord away from traffic areas and where it will not

be tripped over.

11.To disconnect this appliance, turn controls to

the off position and remove plug from outlet.

12.Connect to properly grounded outlets only.

LOCATING YOUR ELECTRIC FIREPLACE

Your new freestanding electric fireplace may be

installed virtually anywhere in your home.

However when choosing a location for your

new electric fireplace, ensure that the general

instructions are followed. For best effect results, install

the electric fireplace out of direct sunlight.

3

CLEARANCE TO COMBUSTIBLES

WARNING: Electrical outlet wiring

must comply with local building

codes and all other applicable

regulations to reduce the risk of

WARNING: Do not use this

it has been

under water. Immediately call a

qualified service technician to

and replace

any part of the electrical system if

Back…………………………0mm

Sides……………..…………0mm

Floor……………. .…………0mm

Top………………. .…………610mm

ELECTRICAL CONNECTION

A 10 AMP, 220 Volt,50Hz circuit with a properly

grounded outlet is required. Preferably, the stove will

be on a dedicated circuit. Other appliances on the

same circuit may cause the circuit breaker to trip or

the fuse to blow when the heater is on operation.

The unit comes standard with a 6’ (1828mm) long

three wire cord exiting from the rear of the fireplace.

Plan the installation to avoid the use of an extension

cord. If an extention cord must be used, it must be a

minumum 1.0 mm2 three wire with grounding type

plug connector and rated no less than 1900 Watts.

fire, electrical shock and injury.

fireplace if any part of

inspect the fireplace

necessary.

ELECTRICAL SPECIFICATIONS

Voltage………………220 VAC/50Hz

Total Amps…………..6.5 Amps

Total Watts…………..1350 Watts

Heater Ratings………1200 Watts

SERVICE INSTRUCTIONS

WARNING: Disconnect power before

attempting any maintenance or cleaning

to reduce the risk of fire, electrical shock

or personal injury

REPLACING LIGHT BULBS

This fireplace uses two clear 220 Volt, 60 Watt, E-14 socket
base light bulbs (small base, chandelier candle type).The
60 Watt bulbs are located under the log set/ember bed. For
convenience, if one of the bulbs burns out, it may be a good

idea to replace both of the light bulbs.

1. Turn off power to the unit by unplugging the power cord.

2. Let fireplace cool if it has been operating.

3.Remove the two fixing self-tapping screws on the screen.

Pull the screen upward a little bit, and then out.

4.Remove the two screws that secure the log set in position.

5.Examine the bulbs to determine which bulbs need to be

replaced.

6. While holding the socket, unscrew the defective bulb (s).

7.Install the new light bulb(s) by holding the socket

and screwing them.

8. Reinstall the log set and screen. Follow the above

procedure in reverse order.

9. The diameter of the pilot light bulb is 5mm. If the pilot

light bulb need to be replaced, follow steps 1,2,3,4

above. Then use the pilot light bulb socket w/wiring

assembly replace the primary pilot part, and connect

wires according to primary connection . Then follow

step 8 above.

WARNING: Do not exceed 60

Watts per bulb. Use of higher

rated bulbs may result in a fire

causing property damage and

personal injury.

4