Procom V50HYLD, V50HYLC User Manual

PRO-COM

V50HYLC
V50HYLD

Freestanding

Electric Fireplace

V50HYLC SHOWN

Installation Instructions and Homeowner’s Manual

WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

FLAMMABLE VAPORS OR LIQUIDS
IN THE VICINITY OF THIS OR ANY
OTHER APPLIANCE

FOR YOUR SAFETY

DO NOT STORE

OR USE GASOLINE OR OTHER

ANSI/UL1278. MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS

INSTALLER: DO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER

CUSTOMER： PLEASE RETAIN THIS MANUAL FOR FUTURE USE

TABLE OF CONTENTS

1

PLEASE READ THE INSTALLATION & OPERATION INSTRUCTIONS BEFORE

USING THIS APPLIANCE

WE ARE PLEASED THAT YOU HAVE CHOSEN TO PURCHASE AN ELECTRIC FIREPLACE MANUFACTURED BY

NANJING PRO-COM ELECTRIC APPLIANCE CO., LTD

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to

follow these instructions may result in a possible electric shock, fire hazard and will void the

warranty.

Important instructions ……………………………………………………………………2

General…………………………………………………………………………………..2

Locating Your Electric Fireplace………………………………………………………2
Clearance To Combustibles…………………………………………………………...3
Electrical Connections…..………………………………………………… ………….3
Electrical Specifications………………………………………………………………..3

Service Instructions…………………………………………………………………………..3

Replacing Light Bulbs…………………………………………………………………..3
Glass Information……………………………………………………………………….4
Maintenance of Motors…………………………………………………………………4
Electrical Wiring Diagram………………………………………………………………4

Operating Instructions……………………………………………………………………….5
On/Off Switch…………………………………………………………………………...5
Heater Control…………………………………………………………………………..5
Instructions for power…………………………………………………………………..5、6
Specifications………………………………………………………………………..….6

Replacement Parts List (V50HYLC) ………………………………………………………7
Replacement Parts Pictures…………………………………………………………...7、8
Replacement Parts List (V50HYLD)…………………………………………………………9

Replacement Parts Pictures……………………………….………………………....9、10

IMPORTANT INSTRUCTIONS

r

f

A

t

r

r

1. Read all instructions before using this appliance.

2. This appliance is hot when in use. To avoid burns, do

not let bare skin touch hot surfaces. Keep
combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 3
feet(1m.) from the front of this appliance.

3. CAUTION: Extreme caution is
necessary when any heater is used
by or near children or invalids and
whenever the heater is left Operating
and unattended.

4. Always unplug heater when not in
use.

5. Do not operate any heater with a
damaged cord or plug or after the
heater malfunctions, has been
dropped or damaged in any manner.

6. Any repairs to this appliance should be carried out by

a qualified service person.

7. Under no circumstances should this electric fireplace

be modified. Parts having to be removed fo
servicing must be replaced prior to operating this

electric fireplace again

8. Do not use outdoors.

9. This heater is not intended for use in bathrooms,

laundry areas or similar indoor locations. Never use
this appliance near a bathtub or vicinity of water.

.

10. Do not run cord under carpeting. Do not cover cord

with throw rugs, runners or the like.
away from traffic areas and where it will not be
tripped over.

Arrange cord

11. To disconnect this appliance, turn controls to the of

position and remove plug from outlet.

12. Connect to properly grounded outlets only.

GENERAL

13. When this appliance is installed, it must be

14. Do not insert or allow foreign objects to enter any

15. To prevent fire, do not block air intakes or exhaust

16. Caution this appliance gets hot and it contains

17. Use this appliance only as described in this

18. Avoid the use of an extension cord because it may

19. SAVE THESE INSTRUCTIONS.

LOCATING YOUR ELECTRIC
FIREPLACE

Your new freestanding electric fireplace may be
installed virtually anywhere in your home.
However when choosing a location for your
new electric fireplace, ensure that the general
instructions are followed. For best effect results, install
the electric fireplace out of direct sunlight.

electrically grounded in accordance with local
codes with the current CSA C22.1 Canadian local
codes of for USA installations. Follow local codes
and National Electrical Code,

ANSI/NFP

NO.70 and Canadian Code: CZ 22.2 NO.0.

ventilation or exhaust opening as this may cause
electric shock, fire or damage to the appliance.

in any manner. Do not use on soft surfaces, such
as a bed, where

internal parts that could arc or spark. Do not use i
in areas where gasoline, paint, or flammable
liquids are used or stored. This electric fireplace
should not be used as a drying rack for clothing.
Also, do not have Christmas stockings o
decorations hung on or near it.

manual. All other uses not recommended by the
manufacturer may cause fire, electric shock, o
injury.

overheat and cause a fire hazard. However if you
must use an extension cord, the cord shall be
NO.16, 1900 Watts. The extension cord must be a
three wire cord with grounding type plug and cord
connector.

openings may become blocked.

2

A

f

f

r

b

r

CLEARANCE TO COMBUSTIBLES

Back………………2”/50.8mm
Sides……………..6”/156.4mm
Floor……………..0”/0mm
Top……………….24”/610mm

ELECTRICAL CONNECTION

15 AMP, 120 Volt, 60Hz circuit with a properly grounded
outlet is required. Preferably, the heater will be on a
dedicated circuit. Other appliances on the same circuit
may cause the circuit breaker to trip or the fuse to blow
when the heater is on operation. The unit comes standard
with a 6’ (1828mm) long three wire cord exiting from the
rear of the fireplace. Plan the installation to avoid the use
of an extension cord. If an extended cord must be used, it
must be a minimum 16 AWG three wire with grounding
type plug connector and rated no less than 1900 Watts.

WARNING: Electrical outlet wiring
must comply with local building
codes and all other applicable
regulations to reduce the risk o
fire, electrical shock and injury.

WARNING: Do not use this
fireplace if any part of it has been
under water. Immediately call a
qualified service technician to
inspect the fireplace and replace
any part of the electrical system i
necessary.

ELECTRICAL SPECIFICATIONS

Voltage………………120 VAC/60Hz
T ot al Amps…………..1 1.3 Amps
Total Watts…………..1345 Watts
Heater Ratings………1200 Watts

SERVICE INSTRUCTIONS

WARNING: Disconnect powe

This fireplace uses two clear 120 Volt, 60 Watt, E-12
socket base light bulbs (small base, chandelier candle
type).The 60 Watt bulbs are located under the log
set/ember bed. For convenience, if one of the bulbs

urns out, it may be a good idea to replace both of the

light bulbs.

1. Turn off power to the unit by unplugging the powe

cord.

2. Let fireplace cool if it has been operating.

3. Open the front door by pulling the handle.

4. Remove the two screws that secure the log set in

position.

before attempting any
maintenance or cleaning to
reduce the risk of fire, electrical
shock or personal injury

REPLACING LIGHT BULBS

5. Remove the two screws of the front baffle and
take them out.

6. Examine the bulbs to determine which one
needs to be replaced.

7. While holding the socket, unscrew the defective
bulb(s).

8. Install the new light bulb(s) by holding the socket
and screwing them in.

9. Reinstall the baffle、log set and screen. Follow

the above procedure in reverse order.

WARNING: Do not exceed 60

Watts per bulb. Use of higher
rated bulbs may result in a fire
causing property damage and
personal injury.

3