Procom FBN280RHAC, FBL280RHAC, FBN280TAC, FBL280TAC Owner's Operation And Installation Manual

1

WARNING: If the information in this manual

is not followed exactly, a fire or explosion may
result causing property damage, personal injury,
or loss of life.

*Aftermarket: Completion of sale, not for purpose of resale,
from the manufacturer.

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

WHAT TO DO IF YOU SMELL GAS

l Do not try to light any appliance.

l Do not touch any electrical switch;do not use any
phone in your building.
l Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
l If you cannot reach your gas supplier, call
the fire department.

Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.

This appliance may be installed in an aftermarket*,
permanently located, manufactured (mobile) home,
where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases.

CUSTOMER CARE: 1-877-866-5989

FBN280RHAC Series Remote Control Fireplace
FBL280RHAC Series Remote Control Fireplace
FBN280TAC Series Thermostat Control Fireplace
FBL280TAC Series Thermostat Control Fireplace

Continental Appliance Inc./U.S. Office

5 Musick 4600 Highlands Parkway S.E.
Irvine Suite# D/E
CA 92618 Smyrna GA 30082

WARNING: This is an unvented gas-

fired heater. It uses air (oxygen) from the room
in which it is installed. Provisions for ad­equate combustion and ventilation air must be
provided. Refer to Air For Combustion and
Ventilation section on page 5 of this manual.

Consumer: Please retain these instructions for future
use.

InstaIIer: Please Leave these instructions with the con­sumer

FULL SIZE VENT-FREE
FIREPLACE

OWNER’S OPERATION AND
INSTALLATION MANUAL

WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Refer to this manual for correct
installation and operational procedures. For assis­tance or additional information consult a qualified
installer, service agency, or gas supplier.

www.usaprocom.com

PC-FBL035-01HR/T-0607

2

IMPORTANT: Read this owner’s
manual carefully and completely
before trying to assemble, operate,
or service this heater. Improper
use of this heater can cause seri­ous injury or death from burns,
fire, explosion, electrical shock,
and carbon monoxide poisoning.

IMPORTIANT SAFETY

INFORMATION

DANGER: Carbon monoxide

poisoning may lead to death!

Carbon Monoxide Poisoning:

Early signs of carbon monoxide poi­soning resemble the flu with
headaches, dizziness, or nausea.
If you have these signs, the heater
may not be working properly. Get
fresh air immediately! Have heater
serviced. Some people are more af­fected by carbon monoxide than
others.These include pregnant
women, people with heart, or lung
disease, anemia, those under the in­fluence of alcohol, and those at high
altitudes.

WARNING: Any change to this fire-

place or its controls can be
dangerous.

WARNING: Do not allow fans to

blow directly into the heater. Avoid any
drafts that alter burner flame patterns.
Ceiling fans can create drafts that al­ter burner flame patterns. Altered
burner patterns can cause sooting.

Do not place clothing or other flam­mable material on or near the
appliance. Never place any objects
in the fireplace.

Due to high temperatures, the appli­ance should be located out of traffic
and away from furniture and
draperies.

WARNING: Do not use a blower

insert, heat exchanger insert, or other
accessory not approved for use with
this heater.

Heater becomes very hot when
running fireplace. Keep children and
adults away from hot surfaces to
avoid burns or clothing ignition.
Fireplace will remain hot for a time
after shutdown. Allow surfaces to cool
before touching.

Carefully supervise young children
when they are in the room with
fireplace.

You must operate this heater with
the heater screen in place. Make
sure heater screen is in place
before running heater.

Keep the appliance area clear and
free from combustible materials,
gasoline,and other flammable
vapors and liquids.

1. This appliance is only for use with
the type of gas indicated on the rat
ing plate. This appliance is not con
vertible for use with other gases.

2. Do not place Propane/LP supply
tank(s) inside any structure.
Locate Propane/LP supply tank(s)
outdoors.

3. If you smell gas

l Shut off gas supply.
l Do not try to light any appliance.
l Do not touch any electrical switch:

do not use any phone in your
building.
l Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
l If you cannot reach your gas
supplier, call the fire department.
and to replace any part of the con­ trol system, and any gas control,
which has been under water.

Important Safety Information ..............2

Air for Combustion and Ventilation.....5

Installation.............................................7

Operating Heater, RHA Models........11

Operating Heater, TA Models............11

Cleaning & Maintenance.....................12

Specifications..................................... 15

Troubleshooting..................................16

Replacement ......................................17

Parts List..............................................18

Installtion Instructions........................22

WARNING

Models FBN280 are equipped for Natu­ral gas. Field conversion is not
permitted.
Models FBL280 are equipped for Pro­pane gas. Field conversion is not
permitted.

Natual and Propane/LP Gas: Natural
and Propane/LP gas is odorless. An
odor-making agent is added to the gas.
The odor helps you detect a gas leak.
However, the odor added to the gas can
fade. Gas may be present even though
no odor exists.

Make certain you read and understand
all warnings. Keep this manual for
reference. It is your guide to safe

and proper operation of this heater.

Table of Contents

4. This heater shall not be installed
in a bedroom or bathroom.

5. Do not use this heater as a
wood-burning heater. Use only
the logs provided with the heater.

6. Do not add extra logs or ornaments

such as pine cones, vermiculite, or

rock wool.Using these added items
can cause sooting. Do not add lava
rock around base. Rock and debris
could fall into the control area of
heater. After servicing, always
replace screen before operating
heater.

7. You must operate this heater with
sure heater screen is in place
before running heater.

3

8. This heater is designed to be
smokeless. If logs ever appear to
smoke, turn off heater and call a
qualified service person.
Note: During initial operation, slight
smoking could occur due to log
curing and heater burning manufac
turing residues.

9. To prevent the creation of soot,
follow the instructions in Cleaning

and Maintenance(page 12).

10. Before using furniture polish, wax,
carpet cleaner, or similar products,
turn heater off. If heated, the vapors
from these products may create a
white powder residue within burner
box or on adjacent walls or furniture.

11. This heater needs fresh air ventila­ tion to run properly. This heater has
an Oxygen Depletion Sensing
(ODS) safety shutoff system.
The ODS shuts down the heater if not
enough fresh air is available. See Air for
Combustion and Ventilation, pages 5
through 6. If heater keeps shutting off,
see Troubleshooting, pages 14
through 15.

12. Do not run heater:

l Where flammable liquids or
vapors are used or stored.
l Under dusty conditions.

13. Do not use this heater to cook
food or burn paper or other objects.

14. Do not use this heater if any part

has been under water. lmmedia­ tely call a qualified service techni­ cian to inspect the room heater.

SAFETY INFORMATION

Continued

QUALIFIED INSTALLING AGENCY

Installation and replacement of gas
piping, gas utilization equipment or ac­cessories and repair and servicing of
equipment shall be performed only by
a qualified agency. The term “qualified
agency” means any individual, firm,
corporation, or company that either in
person or through a representative is
engaged in and is responsible for (a)
the installation,testing,or replacement
of gas piping or(b)the connection,
installation,testing,repair,or servicing
of equipment; that is experienced in
such work; that is familiar with all pre­cautions required,and that has com­plied with all the requirement of the
authorty having jurisdiction.

15. Turn off and unplug heater and
let cool before servicing. Only a

qualified service person should
service and repair heater.

16. Operating heater above
elevations.

18. To prevent performance
problems, do not use propane/
LP fuel tank of less than 100 lbs.
capacity.

PRODUCT FEATURES
SAFETY PILOT

This heater has a pilot with an
Oxygen Depletion Sensing (ODS)
safety shutoff system. The ODS/pilot
is a required feature for vent-free
room heaters. The ODS/pilot shuts
off the heater if there is not enough
fresh air.

MANUAL OVERRIDE CONTROL SYS­TEM

This heater has two operation
functions: Remote Control and Manual
Override Control. The Remote Control
has a transmitter, which requires three
AAA batteries and electric power out­let to operate. If no electric power is
available, then you can operate the
heater by manual override.
The ignitor require one AAA battery.

State of Massachusetts: The instal­lation must be made by a licensed
plumber or gas fitter in the Common­wealth of Massachusetts.
Sellers of unvented propane or natu­ral gas-fired supplemental room heat­ers shall provide to each purchaser a
copy of 527 CMR 30 upon sale of the
unit.
In the state of Massachusetts,
unvented propane or natural gas-fired
space heaters shall be prohibited in
bedrooms and bathrooms.

In the State of Massachusetts the
gas cock must be a “T” handle type.
The State of Massachusetts re­quires that a flexible appliance con­nector cannot exceed three feet in
length.

17. Do not operate heater if any log
is broken. Do not operate heater
if any log is chipped (dime-sized
or larger).of 4,500 feet could
cause pilot outage.

(FBN(L)280RHAC Series)

4

UNPACKING

1. Remove top inner pack.

2. Tilt carton so that fireplace is upright.

3. Remove protective side packaging.

4. Slide fireplace out of carton.

5. Remove protective plastic wrap.

6. Inastall fireplace according to instal
lation instructiona for corner.

7. Hold the screen lift and pulling
forward.

8. Remove log set by cutting plastic
ties.

9. Carefully unwrap log.

10. Check for any shipping damage. If

stove or log is damaged, promptly
inform dealer where you bought
stove.

PRODUCT IDENTIFICATION

Figure1- Vent Free LP/NG Gas Stove

WATER VAPOR: A BY-PRODUCT OF UNVENTED ROOM HEATERS

Water vapor is a by-product of gas combustion. An unvented room heater produces approximately one(1) ounce
(30ml) of water for every 1,000 BTU’s(.3KW’s)of gas input per hour.
Unvented room heaters are recommended as supplemental heater(a room). Rather than a primary heat source
(an entire house). In most supplemental heat applications, the water vapor does not creat a problem. In most
applications,the water vapor enhances the low humidity atmosphere experienced during cold weather.The following
steps will help insure that water vapor does not become a problem.

1.Be sure the heater is a sized properly for the application, including ample combustion air and circulation air.

2.If high humidity is experienced,dehumidifier may be used to help lower the water vapor content of the air.

3.Do not use an unvented room heater as the primary heat source.

lnstall and use heater with care.
Follow all local codes. In the
absence of local codes, use the
latest edition of The National Fuel
Gas Code, ANSZ 223.1, also known
as NFPA 54*.
*Available from:
American National Standards
lnstitute, lnc.
1430 Broadway

New York, NY 10018
National Fire Protection
Association, lnc.

Batterymarch Park

Quincy. MA 02269
This heater is designed for vent­free operation. State and local codes
in some areas prohibit the use of
vent-free heaters.

LOCAL CODES

5

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater

shall not be installed in a confined
space or unusually tight construc­tion unless provisions are provided
for adequate combustion and ven­tilation air. Read the following in­structions to insure proper fresh
air for this andother fuel-burning
appliances in your home.

PROVIDING ADEQUATE
VENTILATION

The following are excerpts from

National Fuel Gas Code, NFPA 54/
ANSI Z 223.1,Section 5.3, Air for
Combustion and Ventilation.

All spaces in homes fall into one of
the three following ventilation
classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space
The information on pages 5 through 6
will help you classify your space and
provide adequate ventilation.

Confined and Unconfined Space

The National Fuel Gas Code, ANS
Z223.1 defines a confined space as a

space whose volume is less than 50
cubic feet per 1,000 Btu per hour (4.8
m3 per kw) of the aggregate input
rating of all appliances installed in that
space and an unconfining space as a
space whose volume is not less
than 50 cubic feet per 1,000 Btu per
hour (4.8 m3 per kw) of the aggregate
input rating of all appliances installed
in that space. Rooms communicat­ing directly with the space in which
the appliances are installed*, through
openings not furnished with doors,
are considered a part of the
unconfined space.

This heater shall not be installed in
a confined space or unusually tight
construction unless provisions are
provided for adequate combustion
and ventilation air.

* Adjoining rooms are communicat­ing only if there are doorless pas­sageways or ventilation grills be­tween them.

Unusually Tight Construction

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.
Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways
or ventilation grills between the rooms.

1. Determine the volume of the space (length×width×height).
Length×Width×Height= cu.ft. (volume of space)
Example: Space size 20ft. (length)×16ft.(width)×8ft. (ceiling height)=2560cu. ft. (volume of space)
If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these
rooms to the total volume of the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.
(volume of space)÷50 cu. ft.=(Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space)÷50 cu.ft.=51.2 or 51,200(maximum Btu/Hr the space can support)

The air that leaks around doors and
windows may provide enough fresh
air for combustion and ventilation.
However, in buildings of unusually
tight construction, you must provide
additional fresh air.
Unusually tight construction is
defined as construction where:
a) walls and ceilings exposed to the
outside atmosphere have a
continuous water vapor retarder

with a rating of one perm (6×10

-11

kg
per pa-sec-m2) or less with
openings gasketed or sealed and

b) weather stripping has been added

on windows that can be opened
and doors and

c) caulking or sealants are applied
to areas such as joints around
window and door frames, between
sole plates and floors, between
wall-ceiling joints, between wall
panels, at penetrations for
plumbing, electrical, and gas
lines, and at other openings.
If your home meets all of the three
criteria above, you must provide
additional fresh air. See Ventilation Air
From Outdoors (page 6).
If your home does not meet all of the
three criteria above, proceed to

Determining Fresh-Air Flow For
Heater Location (below).

6

WARNING: Rework worksheet, adding
the space of the adjoining unconfined
space. The combined spaces must have
enough fresh air to supply all appliances in
both spaces.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an
unconfined space. You will need no additional fresh air ventilation.

3. Add the Btu/Hr of all fuel burning appliances in the space.
Vent-free heater Btu/Hr
Gas water heater* Btu/Hr
Gas furnace Btu/Hr
Vented gas heater Btu/Hr
Gas heater logs Btu/Hr
Other gas appliances* + Btu/Hr
Total = Btu/Hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and
vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

Btu/Hr (maximum the space can support)
Btu/Hr (actual amount of Btu/Hr used)
Example : 51,200 Btu/Hr(maximum the space can support)

56,000 Btu/Hr(actual amount of Btu/Hr used)
The space in the above example is a confined space because the actual Btu/Hr used is more than the
maximum Btu/Hr the space can support.
You must provide additional fresh air. Your options are as follows:
A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined
space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From
Inside Building (below).
B. Vent room directly to the outdoors. See Ventilation Air From Outdoors (below).
C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

Figure 2 -Ventilation Air from Inside Building

Example:
Gas water heater 30,000 Btu/Hr
Vent-free heater + 26,000 Btu/Hr
Total = 56,000 Btu/Hr

WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined
space or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one
of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3 or applicable local codes.

This fresh air would come from an adjoining uncon­fined space. When ventilating to an adjoining uncon­fined space, you must provide two permanent openings:
one within 12" of the ceiling and one within 12" of the
floor on the wall connecting the two spaces (see
options 1 and 2, Figure 2). You can also remove door
into adjoining room (see option 3, Figure 2). Follow the

National Fuel Gas Code. NFPA 54/ANSI Z223.1, Sec­tion 5.3, Air for Combustion and Ventilation for re-

quired size of ventilation grills or ducts.

Ventilation Air From lnside Building

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts.
You must provide two permanent openings: one within
12" of the ceiling and one within 12" of the floor. Connect
these items directly to the outdoors or spaces open to
the outdoors. These spaces include attics and crawl
spaces. Follow the National Fuel Gas Code, NFPA 54/

ANSI Z223.1, Section 5.3, Air for Combustion and Ven­tilation for required size of ventilation grills or ducts.

IMPORTANT: Do not provide openings for inlet or outlet
air into attic if attic has a thermostat-controlled power
vent. Heated air entering the attic will activate the power
vent.

Figure 3 -Ventilation Air from Outdoors

7

NOTICE: This heater is

intended for use as supplemen­tal heat. Use this heater along with
your primary heating system. Do
not install this heater as your
primary heat source. If you have
a central heating system, you
may run system's circulating
blower while using heater. This
will help circulate the heat
throughout the house.

INSTALLATION

WARNING: A qualified techni­cian person must install heater. Fol­low all local codes.

WARNING: Never install the
heater

l in a bedroom or bathroom
l in a recreational vehicle

l where curtains, furniture, clothing,

or other flammable objects are
less than 42 inches from the
front, top, or sides of the heater

l in high traffic areas
l in windy or drafty areas

WARNING: Maintain the mini­mum clearances. If you can, pro­vide greater clearances from floor,
ceiling, and adjoining side and
back walls.

warm air currents. These currents
move heat to wall surfaces next to
heater. Installing heater next to vinyl
or cloth wall coverings or operating
heater where impurities (such as
tobacco smoke, aromatic candles,
cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may
discolor walls.

IMPORTANT: Vent-free heaters add
moisture to the air. Although this is
beneficial, installing heater in rooms
without enough ventilation air may
cause mildew to form from too much
moisture. See Air for Combustion and
Ventilation, pages 5 through 6.

CHECK GAS TYPE

Use only the type of gas indicated on
the plate. If your gas supply can not
meet that requirement, do not install
heater. Call the dealer where you pur­chased heater, for the proper type of
heater.

Figure 4 -Minimum Clearance to Wall and Ceiling

CLEARANCES TO COMBUSTIBLES
(Vent-Free Operation Only)

Carefully follow the instructions below.
This fireplace is a freestanding unit
designed to set directly on the floor.

IMPORTANT: You must maintain
minimum wall and ceiling clearances
during installation. The minimum
clearances are shown in Figure 4.
Measure from outermost point of stove
top.

Minimum Wall and Ceiling Clearances

(see Figure 4)
A. Clearances from outermost point

of stove top to any combustible side
wall should not be less than 0
inches.

B. Clearances from the stove top to

the ceiling should not be less than
48 inches.

CAUTION: This heater creates

8

CONNECTING TO GAS
SUPPLY

WARNING: A qualified techni­cian must connect heater to gas
supply. Follow all local codes.

CAUTION: Never connect heater
directly to the gas supply. This heater
requires an external regulator (not
supplied). lnstall the external regu­lator between the heater and gas
supply.

INSTALLATION ITEMS NEEDED

Before installing heater, make sure
you have the items listed below.

l piping (check local codes)
l sealant (resistant to propane/LP

gas)

l equipment shutoff valve*
l test gauge connection**
l sediment trap
l tee joint
l pipe wrench
l Flexible Gas hose(check local code)

* A CSA design-certified equipment
shutoff valve with 1/8" NPT tap is an
acceptable alternative to test gauge
connection. Purchase the optional
CSA design-certified equipment
shutoff valve from your dealer. See
Accessories.

Figure 5 -Gas Regulator Location
and Gas Line Access Into Stove
Cabinet

Figure 6 -External Regulator With
Vent Pointing Down

Figure 7 -Gas Connection

The installer must supply an external
regulator. The external regulator will
reduce incoming gas pressure. You
must reduce incoming gas pressure
to between 11 and 14 inches of water.
If you do not reduce incoming gas
pressure, heater regulator damage
could occur. lnstall external regulator
with the vent pointing down as shown
in Figure 6. Pointing the vent down
protects it from freezing rain or sleet.

* Purchase the optional CSA design-certified equipment shutoff valve
from your dealer. See Accessories.
** Minimum inlet pressure for purpose of input adjustment.

NG Models:
5” to 10.5” W.C.
Gas supplier provide external
regulator for natural gas

INSTALLATION

Continued

WARNING: Never connect
heater to private (non-utility) gas
wells. This gas is commonly known
as wellhead gas.

Front View

CAUTION: Only use a new black
iron or steel pipe. Internally-tinned
copper tubing may be used in
certain areas. Check you local

codes. Use pipe of 1/2" diameter or
greater to allow proper volume gas

to heater. If pipe is too small, undue
loss of pressure will occur.

Installation must include an equip­ment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT
tap within reach for test gauge hook
up. NPT tap must be upstream
from heater (see Figure 7).

IMPORTANT: Install equipment
shutoff valve in an accessible location.
The equipment shutoff valve is for
turning on or shutting off the gas to
the appliance. Apply pipe joint sealant
lightly to male threads.This will pre­vent excess sealant from going into
pipe. Excess sealant in pipe could
result in clogged heater valves.

CAUTION: Use pipe joint seal­ant that is resistant to gas
(PROPANE or NG).

We recommend that you install a
sediment trap in a supply line as
shown in Figure 7. Locate sediment
trap where it is within reach for cleaning.
Install in the piping system between
fuel supply and heater. Locate sedi­ment trap where trapped matter is not
likely to freeze. A sediment trap traps
moisture and contaminants. This
keeps them from going into heater
controls. If sediment trap is not in­stalled or is installed incorrectly,
heater may not run properly.

CAUTION: Avoid damage to
regulator. Hold gas regulator with
wrench when connecting into gas
piping and/or fittings.

Propane/LP

Supply Tank

9

WARNING: Never use an open
flame to check for a leak. Apply a
mixture of liquid soap and water to
all joints. Bubbles forming show a
leak. Correct all leaks immediately.

CAUTION: Make sure external
regulator has been installed be­tween gas supply and heater. See
guidelines under Connecting to Gas
Supply (page8).

Figure 8 -Equipment Shutoff Valve

Pressure Testing Gas
Supply Piping System

Test Pressures In Excess Of 1/2
PSIG(3.5kPa)

1. Disconnect heater with its
appliance main gas valve (control
valve) and equipment shutoff valve
from gas supply piping system.
Pressures in excess of 1/2 psig
will damage heater regulator.

2. Cap off open end of gas pipe
where equipment shutoff valve
was connected.

3. Pressurize supply piping system
by either using compressed air or
opening gas supply tank valve.

4. Check all joints of gas supply
piping system. Apply mixture of
liquid soap and water to gas
joints. Bubbles forming show a
leak.

5. Correct all leaks immediately.

6. Reconnect heater and equipment
shutoff valve to gas supply. Check
reconnected fittings for leaks.

Pressure Testing Heater
Gas Connections

1. Open equipment shutoff valve
(see Figure 8).

Figure 9 -Checking Gas Joints

CHECKING GAS CON­NECTIONS

WARNING: Test all gas piping
and connections for leaks after
installing or servicing. Correct all
leaks immediately.

INSTALLATION

Continued

2. Open gas supply tank valve.

3. Make sure control knob of heater is
in the OFF position.

4. Check all joints from equipment
shutoff valve to control valve
(Figure 9). Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.

5. Correct all leaks immediately.

6. Light heater (see Operating
Heater, page 11).Check all other
internal joints for leaks.

7. Turn off heater (see Operation of

Turn-Off , page 11).

Test Pressures Equal To or
Less Than 1/2 PSIG(3.5 kPa)

1. Close equipment shutoff valve
(see Figure 8).

2. Pressurize supply piping system
by either using compressed air
or opening gas supply tank valve.

3. Check all joints from gas meter to
equipment shutoff valve(see
Figure 9). Apply mixture of liquid
soap and water to gas joints.
Bubbles forming show a leak.

4. Correct all leaks immediately.

10

INSTALLATION

Continued

WARNING: Failure to position
the parts in accordance with these
diagrams or failure to use only parts
may result in property damage or
personal injury.

CAUTION: After installation and
periodically thereafter, check to en­sure that no flame comes in
contact with any log. With the heater
set to High, check to see if flames
contact any log. If so, reposition logs
according to the log installation
instructions in this manual. Flames
contacting logs will create soot.

INSTALLING LOGS

It is very important. To install the logs exactly as instructed. Do not modify
logs. Only use logs supplied wall heater.

IMPORTANT: Make sure log does not cover any burner ports (see
Figure 10).

Figure 10 -Installing Log Set

FIG(1) FIG(2)

STEP 1: Install the log 1on the left
rear angle iron. See FIG(2).

STEP 2:Install the log 2 on the right rear
iron. See FIG(3).

STEP 3:Install the log 3 on the front
angle. See FIG(4).

FIG(3)

FIG(4)

STEP 4:Insert the pinhole on the upper
part on the left side of log 1. Place the
lower part of log 4 on the flat roof at the left
side of log 3. See FIG(5).

STEP 5:Insert the pinhole on the upper
part of log 5 in the pin on the log 2. Place
the lower part of log 5 on the flat roof at
the left side of log . See FIG(6).

FIG(5)

FIG(6)

1. All logs. See FIG(1).

11

OPERATING HEATER

FOR YOUR SAFETY

RHA Series Models

A. This appliance has a pilot which

must be lighted by control system,
When lighting the pilot, follow
these instructions exactly.

B. BEFORE LIGHTING smell all

around the appliance area for
gas. Be sure to smell next to the
floor because some gas is
heavier than air and will settle
on the floor.

WHAT TO DO IF YOU SMELL GAS

CAUTION: Do not try to adjust
heating levels by using the
equipment shutoff valve.

1. STOP! Read the safety information,
page 2.

2. Make sure equipment shutoff
valve is fully open.

Note: If operating by remote control,
you must set the Control Knob on
ELECTRIC position.

Do not set the control knob between
the locked position, otherwise there
will be no power to the heater.

Note: Please wait one minute after

shutting off fireplace to allow the
electronic module to reset before

starting again.

Note: To operate your heater the ON/

OFF switch on front of heater must be
in the ON position. The RED light on
the front of heater indicates there is
electrical power to your heater when
the ON/OFF switch is in the ON po­sition. The GREEN light on the fr­ont of heater indicates the pilot light
is ON. (See Figure 11)

WARNING: If you do not
follow these instructions exactly, a
fire or explosion may result causing
property damage, personal injury or
loss of life.

NOTICE: During initial operation
of new fireplace, burning logs will
give off a paper-burning smell. Or­ange flame will also be present.
Open a window to vent smell. This
will only last a few hours.

Do not try to light any appliance.
Do not touch any electrical switch;

do not use any phone in your
building.
Immediately call your gas sup
plier from a neighbor’s phone.
Follow the gas supplier’s
instructions.
If you cannot reach your gas
supplier, call the fire department.

C. Use only your hand to push in
control knob. Never use tools. If the
the appli ance could not operate , don't
try to repair it, Call a qualified service
technician or gas supplier.Forced or at­tempted re-pair may result in a fire or
explosion.

D. Do not use this appliance if any
part has been under water. Imme­diately call a qualified service techni­cian to inspect the appliance and to
replace any part of the control system
and any gas control which has been
under water.

Function of power ON/OFF swith.

LIGHTING INSTRUCTIONS

Figure 11 - ON/OFF Switch location

OPERATIONS OF

REMOTE TRANSMITTER

1. Install three AAA batteries in the
battery holder. The initial start-up on
the LCD is: SET TEMP is 85°F,
ROOM TEMP is 85°F, and fan is on

“AUTO” select.

Fig 12 Initial start-up on the LCD

2. When in operation, point the
remote transmitter to the remote

receiver on the front of fireplace at
a maximum distance of 20 feet
without any obstruction between
them.

OPERATIONS OF

BURNER

1. Before plugging into the outlet
make sure that the appliance is
connected to the gas supply. Plug
fireplace into a properly grounded
120 Volt, 60Hz, 15 amp outlet. You
will hear a high pitch sound and
power light(red) on the door will
be lit that indicates that the
burner is ready to be operated.

2. Point the remote transmitter to
the burner. Press IGN/OFF button,
the electric spark starts igniting
the pilot and then the burner. Wait
five (5) minutes to clear out any
air. If you smell gas. STOP!
Please check the gas connection.
The green operation light on the
front of fireplace will be lit when
pilot and burner are on.

Note: The main burner does not
respond immediately to the set
temperature until about one
minute later.

3. To shut off, press IGN/OFF button
on remote or on front of fireplace.

Note: The pilot will also shut off.

12

Fig13 Control board

OPERATING HEATER

Continued

Auto off: when the burner is in
operation, press TIMER button. Then
press or to change to the sched­uled time, then press the TIMER button
again, the TIMER starts timing and the
TIMER will flash and the green opera­tion light flashes. Burner will automati-

cally shut off at set time.

OPERATIONS OF

TIMER

LOCKING REMOTE

CONTROL

( child proof )

1. To Lock: Press LOCK button , a
symbol will appear on control board.

2. To Unlock: Press LOCK button and
hold until lock image shows un-

locked (typically 6 secs.).

Fig14 “AUTO” select

▼

▼

We provide the manual override con­trol system in the event of power
outage.

Install battery for manual Ignitor:

1. Unscrew the ignitor cap.

2. Insert a AAA type battery with its
anode (“+”) pointing out.

3. Screw the ignitor cap back.
Note: We recommend that the battery
be taken out of the ignitor when the
power supply resumes.

LIGHTING INSTRUCTIONS

If power is off, you can operate the
fireplace manually.

1. STOP! Read the safety information
on page 11.

2. Check that gas supply to heater is
on.

3. Open bottom front access panel.

4. With Control Knob in the on ELEC­TRIC position, press in the Control
Knob and turn counterclockwise to
OFF position.

NOTE: Knob cannot be turned

from PILOT/IGN to “OFF” unless
knob is pushed in slightly. Do not
force.

5. Wait five (5) minutes to clear out
any gas. Then smell for gas,
including near the floor. If you smell
gas, STOP! Follow “B” in the safety
information on page 11. If you do
not smell gas, go to the next step.

6. Push in gas control slightly and turn
counterclockwise to PILOT/IGN
and depress for five (5) seconds.

NOTE: The first time that the heater

is operated after connecting the
gas supply, the control knob should
be depressed for about thirty (30)
seconds. This will allow air to
bleed from the gas system.

7. With Control Knob pressed in,
push ignitor button. This will light
the pilot. If needed, keep ignitor
button until pilot lights.

MANUAL OVERRIDE
CONTROL SYSTEM OPERATING

INSTRUCTIONS

8. Keep Control Knob depressed for
ten (10) seconds after lighting
pilot. If pilot goes out, repeat steps
6, 7 and 8.

9. Turn counterclockwise to “ON”
position. Do not operate between
locked positions.

Shut off heater

Push in gas Control Knob slightly
and turn clockwise to the OFF
position. Do not force.

When electric power is available and
electric operation is desired, turn

clockwise to OFF position for
one minute to allow the electronic
module to reset before starting. Then
press down knob and rotate clock-

wise to ELECTRIC position.
Do not operate between locked
positions.

1. Open front door.

2. Follow steps 1 through 5 under

MANUAL OPERATING Lighting
Instructions.

3. With Control Knob in PILOT/IGN
position, strike match, and hold
near pilot. Press in Control Knob,
pilot should light.

4. Keep Control Knob pressed in for
30 seconds after lighting pilot.
After 30 seconds, release Control
Knob. Follow step 9 under

MANUAL OVERRIDE CONTROL
SYSTEM OPERATING
INSTRUCTIONS.

INSPECTING BURNERS

TO TURN OFF GAS

TO APPLIANCE

Check pilot flame pattern and burner
flame patterns often.

MANUAL LIGHTING

PROCEDURE

(match light)

TO TURN OFF GAS TO APPLIANCE
Shut off heater

1. Press the IGN/OFF button.(see fig-

ure 15)

2. Set the ON/ OFF Switch position or

unplug the electric power to the heater.

Set temperature: Press “Temp”
button, then press or to set desired
room temperature. Burner will operate

to maintain set room temperature.

a.

b. Set blower: Press “FAN” button. the
blower will shift between “AUTO” and

“OFF” option.

When “FAN” is in “AUTO” select: the
blower will be oprate depend on the tem­perature inside the heater. and automati­cally turn ON or OFF.
When Fan is in “ OFF” select the blower
will not operate.

▼

▼

13

Figure 15 -Correct Pilot Flame Pattern

PILOT FLAME PATTERN

Figure 15 shows a correct pilot
flame pattern. Figure 16 shows an
incorrect pilot flame pattern. The
incorrect pilot flame is not touching
the thermocouple.This will cause the
thermocouple to cool. When the
thermocouple cools, the heater
will shut down. If pilot flame pattern
is incorrect, as shown in Figure 18
l Turn heater off (see TO TURN OFF
GAS TO APPLIANCE, page 9)
l see troubleshooting, page 15.

Figure 16 -Incorrect Pilot Flame
Pattern

Figure 17 shows a correct burner
flame pattern. Figure 18 shows an
incorrect burner flame pattern. If
burner flame is incorrect:
l Turn heater off (see TO TURN OFF
GAS TO APPLIANCE, page 10)

l see troubleshooting, page 15.

BURNER FLAME PATTERN

Figure 17 -Correct Flame Pattern
with Control Knob Set to High Flame

Figure 18 -Incorrect Flame Pattern
with Control Knob Set to High Flame

DISCONNECT WIRNG OR CONTROL
MODULE

1. Remove four screws from the rear
control panel , take out thermostat
sensing bulb from the clip, then disco­nnect the wires to free to control
module from its mounting location .
Note: Do not confuse the mark on
the each wire.

2. Remove two screws and hex nuts,
take out the control module. When in­stalling , reverse the steps above.
(See Figure 19 and Figure 22)

Figure 19- Control Model

DISCONNECT FAN

1.Remove screws from the fan
bracket panel , pull the fan bracket
panel out to remove. Then disconne­ct two wires free to fan.

2.Mark or tag each wire removed
for its exact reconnection. Remove
the four screws from the fan .when
installing , reverse the steps above.
(See Figure 20 and Figure 22)

Figure 20- Fan

WARNING: Disconnect power be-

fore attempting any maintenance or
cleaning to reduce the risk of fire , elec­tric shook or personal injury. Turn off
heater and let cool before cleaning.

CLEANING AND MAINTENANCE

CAUTION:

Label all wires prior to

disconnection

when servicing

Wiring errors can cause

improper and dangerous operation.

Verify proper operation after servicing.

controls

.

CAUTION: You must keep control

areas, burner, and circulating air pas­sageways of heater clean. Inspect
these areas of heater before each
use. Have heater inspected yearly by
a qualified service person. Heater
may need more frequent cleaning due
to excessive lint from carpeting,
bedding material, pet hair, etc.

CLEANING ODS/IGNITOR AND
BURNER

Clean with a vacuum cleaner.

CLEANING BURNER
INJECTOR HOLDER AND
PILOT AIR INLET HOLE

We recommend that you clean the unit
every three months or after 2500 hours
of operation. We also recommend that
you keep the burner tube and pilot as­sembly clean and free of dust and
dirt. To clean these parts we recom­mend using compressed air no greater
than 30 PSI. You can use a vacuum
cleaner in the blow position. If using
compressed air in a can, please fol­low the directions on the can. If you don't
follow directions on the can, you could
damage the pilot assembly.

WARNING: Failure to keep
primary air openings of burners clean
may result in sooting and property
damage.

14

CLEANING AND MAINTENANCE

Continued

Figure 22 -Pilot Air Inlet Hole

CABINET

Air Passageways

l Use a vacuum cleaner or

pressurized air to clean.

MAIN BURNER

Periodically inspect all burner flame
holes with the heater running. All
slotted burner flame holes should
be open with yellow flame present. All
round burner flame holes should be
open with a small blue flame
present. Some burner flame holes
may become blocked by debris or
rust, with no flame present. If so,
turn off heater and let cool. Either
remove blockage or replace burner.
Blocked burner flame holes will
create soot.

1. Shut off the unit, including the
pilot. Allow the unit to cool for at
least thirty minutes.

2. Inspect burner, pilot and primary air
inlet holes on injector holder for
dust and dirt (see figure 21).

3. Blow air through the ports/slots
and holes in the burner.

4. Check the injector holder located
at the end of the burner tube
again. Remove any large particles
of dust, dirt, lint, or pet hair with a
soft cloth or vacuum cleaner
nozzle.

5. Blow air into the primary air holes
on the injector holder.

6. In case any large clumps of dust
have now been pushed into the
burner, repeat steps 3 and 4.

Figure 21 -Injector Holder On Outlet
Burner Tube

Exterior

l Use a soft cloth dampened with a

mild soap and water mixture. Wipe
the cabinet to remove dust.

LOGS

l If you remove logs for cleaning,

refer to Installing Logs (page 10)
to properly replace logs.

l Replace logs if broken or chipped

(dime-sized or larger).

Clean the pilot assembly also. A
yellow tip on the pilot flame
indicates dust and dirt in the pilot
assembly. There is a small pilot air

inlet hole about two inches from
where the pilot flame comes out of
the pilot assembly (see Figure 22).
With the unit off, lightly blow air
through the air inlet hole. You may
blow through a drinking straw if
compressed air is not vailable.

Figure 22- Remote Control System Diagram

15

SPECIFICATIONS

Btu(Variable) 28000 28000
Gas Type LP Gas Natural Gas
Ignition Piezo/Automatic Piezo/Automatic
Manifold Pressure 8"W.C. 3"W.C.
Inlet Gas Pressure
(In. of water)*
Maximum 14" 10.5"
Minimum 11" 5"
Dimensions, Inches (H×W×D)
Heater 36 1/4”×53 13/16”×29 1/2” 36 1/4”×53 13/16”×29 1/2”
Carton 40 5/8”×54 3/4”×18 1/8” 40 5/8”×54 3/4”×18 1/8”
Weight, lbs
Stove 130 130
Shipping 157 157
Voltage 120 120
Watt 27 27

*For purposes of input adjustment

FBL280TAC
FBL280RHAC

FBN280TAC
FBN280RHAC

16

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

1. Thermocouple connection loose
at control board

2. Pilot flame not touching

thermcouple which allows thermo­couple to cool, causing pilot
flame to go out. This problem
could be caused by one or both of
the following
A) Low gas pressure
B) Dirty or partially clogged
ODS/ pilot

3. Thermocouple damaged

4. Control valve damaged

1. Hand tighten until snug, then
tighten 1/4 turn more.

2. A) Contact local propane/LP gas
company.

B) Clean ODS/pilot (see Cleaning

and Maintenance, page 13) or

replace ODS/pilot assembly

3. Replace thermocouple

4. contact dealer or procom.

ODS/pilot lights but flame is continu­ous igniting and the main burner
couldn’t be lit.

TROUBLESHOOTING

WARNING:Make sure that power

is turn off before proceeding....

WARNING: Turn off and let cool
before servicing. Only a qualified
service person should service and

repair fireplace.

CAUTION: Never use a wire,
needle, or similar object to clean
ODS/pilot. This can damage ODS/
pilot unit.

Spark at ODS/pilot but no ignition

1. Gas supply turned off or equip­ment shut off valve closed

2. Air in gas lines when installed.

3. Depleted gas supply

4. ODS/pilot is clogged

5. Gas regulator setting is not correct

6. Pilot electrude position is not
correct

7. Wire is not correct or loosen

8 Gas valve is damage

1. Turn on gas supply or open equip­ment shutoff valve

2. Press ON/OFF button again
until air is removed .

3. Contact local propane/LP gas
company
4 Clean ODS/pilot (see Cleaning
and Maintenance,page 13 ) or
replace ODS/pilot assembly

5. Replace gas control

6. Replace Pilot

7. Check the wine and make wine
correct.

8. Contact dealer or procom.

No spark when ignition button is
pressed.

1. No power to heater

2. No battery in transmitter or battery
isn’t correctly assembly

1. Check the electric power

2. Place or replace the battery.

WARNING: If you smell gas

l Shut off gas supply.
l Do not try to light any appliance.
l Do not touch any electrical switch; do not use any phone in your

building.
l Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
l If you cannot reach your gas supplier, call the fire department.

17

Delayed ignition burner

1. Manifold pressure is too low

2. Burner orifice clogged

1. Contact local gas company

2. Clean burner (see Cleaning and
Maintenance, page 13)

Burner backfiring during combustion

1. Damaged burner

2. Gas regulator defective

1. Clean burner orifice (see
Cleaning and Maintenance, page

13)

2. Replace gas regulator

Slight smoke or odor during initial
operation

1. Residues from manufacturing
processes

2. Not enough air

3. Gas regulator defective

1. Problem will stop after a few
hours of operation

2. Check burner for dirt and debris.
If found, clean burner (see Cleaning
and Maintenance, page 13)

3. Replace gas regulator

Dark residue on logs or inside of
fireplace

1. Improper log placement

2. Air holes at burner inlet blocked

3. Burner flame holes blocked

1. Properly locate logs (see installing
logs, page 10)

2. Clean out air holes at burner inlet.

Periodically repeat as needed.

3. Remove blockage or replace burner

Heater produces a clicking/ticking
noise just after burner is lit or
shut off

1. Metal expanding while heating
or contracting while cooling

1. This is common with most
heaters. If noise is excessive,
contact qualified technician.

TROUBLESHOOTING

Continued

l Your name
l Your address
l Model and serial numbers

of your heater

l How heater was malfunctioning
l Type of gas used (propane/LP or

NG)

l Purchase date

REPLACEMENT PARTS

l Warranty card
Usually, we will ask you

to return the defective part to the
factory.

REPLACEMENT PARTS
NOTE: Use only original replace-

ment
parts. This will protect your warranty
coverage for parts replaced under
warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this
product. If they can't supply original
replacement part(s), call ProCom’s
toll free number at (1-877-886-5989)
for referral information.
When calling PRroCom or your
dealer, have ready:

PARTS NOT UNDER
WARRANTY

Contact authorized dealers of this
product. If they can’t supply original re­placement part(s) call ProCom’s toll free
number at (1-877-886-5989) for referral
information.
When calling ProCom, have ready

l Model number of your heater
l The replacement part number

Burner does not light after ODS/pilot
is lit

1. Burner orifice clogged

2. Inlet gas pressure is too low

3. Burner orifice diameter is too
small

4. Thermocouple leads discon­nected or improperly connected

5. Burners will not come in
remote position

1.Clean burner (see Cleaning

and Maintenance, page 13) or
replace burner orifice.

2. Contact local propane/LP

gas company

3. Replace burner orifice

4. Reconnect leads (see wiring

diagram)

5. Replace battery in transmitter

and receiver

18

PARTS LIST

FBN280TAC
FBL280TAC

LPNG

SIT545-218T-STAT VALVE1

SIT545-200T-STAT VALVE1
NRV81F1-3REGULATOR1
NRV81F1-8REGULATOR1

BL023-01INJECTOR1

BL024-01INJECTOR1
NBY28-025B3BURNER ASSEMBLY1
NBY28-160B3BURNER ASSEMBLY1

ND1703X400X4ODS1
ND1908X400X4ODS1

6FBB106

ODS INLET TUBE ASSEMBLY

11
7FBB104INLET TUBE ASSEMBLY11
8FBB105OUTLET TUBE ASSEMBLY11

QUALITY

KEY NOPART NUMBERDESCRIPTION

5

1

2

3

4

This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.

19

PARTS LIST

FBN280TAC
FBL280TAC

This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.

LPNG

1

BB26000LOGS11

2

FB280AC6-01

TOP PANEL11

3

FB280AC6-03

SIDE PANEL11

4

FB280AC6-04

SIDE PANEL11

5

FB280AC6-05

BASE11

6

FB280AC6-02

UPPER PANEL11

7

FBL001-01BODY TOP COVER11

8

FBL008-01BBAFFLE11

9

FBL006-01BSIDE REFLECTOR22

10

FBL007-01AFIREBOX FLOOR11

11

FBL002-01LOUVER88

12

FBL001-03RHBODY BOTTOM COVER11

13

FBL001-02SBODY BOARDING11

14

FBL010-01BUPPER PANEL11

15

FBB102SCREEN11

16

ML083-02IGNITOR11

17

FBL015-01T-STA VALVE BRACKET11

18

QL016-03RBLOWER MOUNT PANEL11

19

PF06-YJLF-FFAN 11

QUALITY

KEY NOPART NUMBERDESCRIPTION

20

PARTS LIST

FBN280RHA
FBL280RHA

LPNG

1NV2020-22*

OVERRIDE CONTROL SYSTEM

11

2BL015-03RA

T-STAT VALVE BRACKET

11

3FBB33000RH

ODS INLET TUBE ASSEMBLY

11

4FBB31000RHINLET TUBE ASSEMBLY11

NRV81F1-3REGULATOR1

NRV81F1-8REGULATOR1
ND4703X400-RHODS1
ND4808X400-RHODS1

NBY28-025B3BURNER ASSEMBLY1

NBY28-160B3BURNER ASSEMBLY1

BL023-01INJECTOR1
BL024-01INJECTOR1

9FBB32000RH

OUTLET TUBE ASSEMBLY

11

QUALITY

KEY NOPART NUMBERDESCRIPTION

8

5

6

7

This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.

21

PARTS LIST

FBN280RHA
FBL280RHA

This list contains replaceable parts used in your heater. When ordering
parts, follow the instructions listed under Replacement Parts on page 17
of this manual.

Key No.Part NumberDescriptionQTY

1QL016-03RBLOWER MOUNT PANEL1
2PF06-Y JLF-FBLOWER 1
3NAYB03-00CONTROL CABINET ASSEMBLE1
4NAYB01-00REMOTE1
5NAYB02-00RECEIVER ASSEMBLE1
6FBB102SCREEN1

22

INSTALLATION:

1.Surround must be installed flush with wall. Baseboards
will prevent proper installation of surround.
Baseboards can be altered to fit surround by cutting
that part within 34 1/2” distance from the wall corner.

2.Surround must be attached to either a wall stud or wall
anchor. Use a tape measure to determine correct
height from floor to location of mounting strips. (See
Figure 1). Make sure point of the mitered edge of
mounting strip touches the corner. Use a level to en­sure mounting strips are evenly balanced.

IMPORTANT: Failure to balance mounting strips
with a level could result in uneven surfaces on
fully assembled surround.

3.Fasten mounting strip to wall by inserting 2" screws
provided along the predrilled holes of mounting strip.
If predrilled holes of mounting strip do not line up with
wall studs, drill new holes where wall studs are or at­tach to wall with wall anchors. (See Step 4 below.)

4.To use wall anchors, drill holes at marked location
using 5/16” drill bit. Fold wall anchor (see Figure 2)
and insert (wings first) into hole. Tap anchor flush into
wall. For thin walls, insert red key into wall anchor and
push to “pop” open anchor wings (see Figure 3).

5.Repeat steps above to attach other mounting strips
to wall. Make sure mitered edges fit together to form
a clean joint in the corner of the wall.

INSTALLATION INSTRUCTIONS

For CORNER SURROUND AND HEARTH

READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION. Check to see that you have
the following. If any part or parts are missing, contact the dealer where you bought the sur­round and hearth.

TOOLS REQUIRED:

Measuring Tape, Pencil, Level, #2 Phillips Screw Driver, Hammer, Electric Drill, 5/6" Drill Bit,
Hand or Electric Saw

Figure 1

Figure 3

Figure 2

19 1/2”

19 1/2”

23

6. Place the assembled fireplace on the middle where it is 30” from the corner and
form a 45 degree angle to each side wall. Move the assembled surround to the
corner, with side panels close to side walls. Move the fireplace to where it can prop­erly attach the surround.

7. Move the surround away, mark floor or wall behind fireplace for gas line entrance.
Connect inlet gas pipe.

IMPORTANT: Make sure there are no electrical lines where gas piping will
go through floor or wall.

8. Turn up the back of mantel top, the special spring will lock the rear mantel top in
position, then use screws to secure bracket as show in Figure 5 make sure the front
and rear mantel top are in the same level.

9. Move the surround back. Set surround top on top of mounting strips and mantel
front. After properly installing the top, attach surround top to mounting strip using
finishing nails.

10.Push the base to the bottom of surround, close to the right and left sides.

11.Install fireplace per Homeowner’s Installation Manual.

Figure 4

Figure 5

Figure 6

19 11/16”