Page 1
Made in Switzerland
60 Years of Innovation
PUNDIT® PL-200PE
OPERATING INSTRUCTIONS
Made in Switzerland
60 Years of Innovation
Page 2
© 2014 Proceq SA 2
A
Pundit Touchscreen
B
Battery
C
Pundit Pulse Echo Transducer*
D
Pundit Pulse Echo Cable*
E
Pundit Pulse Echo Contact Tester*
F
Battery Charger
G
USB Cable
H
DVD with Software
I
Documentation*
J
Carrying Strap
K
Calibrated Tape*
*Part of the “Pundit Pulse Echo Transducer” package (Part No. 327 40 130)
A
F
J
G
B
H
I
Scope of Delivery
D
E
C
K
Page 3
9
9
9
9
9
9
9
9
9
9
23
23
9
3.2
23
3 © 2014 Proceq SA
Overview Pundit PL-200PE
1
1
2
3
4
5
6
7
8
9
10
2
Page 4
© 2014 Proceq SA 4
Table of Contents
1. Safety and Liability ...................................................... 5
1.1 General Information ...........................................................5
1.2 Liability ...............................................................................5
1.3 Safety Instructions ............................................................5
1.4 Correct Usage ...................................................................5
2. Technical Specifications .............................................. 6
3. Operation ...................................................................... 6
3.1 Getting Started ..................................................................6
3.2 Main Menu .........................................................................7
3.3 Settings ..............................................................................7
3.4 Measurement Screen ........................................................9
3.5 Measurement Modes ......................................................11
3.6 Measuring with Pundit PL-200PE ...................................12
4. Explorer ...................................................................... 12
4.1 Analysis of B-Scans ........................................................13
5. Ordering Information ................................................. 13
5.1 Units .................................................................................13
5.2 Transducers .....................................................................13
5.3 Accessories .....................................................................14
6. Maintenance and Support ......................................... 14
6.1 Maintenance ....................................................................14
6.2 Support Concept ............................................................14
6.3 Warranty Information .......................................................14
6.4 Disposal ...........................................................................14
7. PL-Link Software ....................................................... 15
7.1 Starting PL-Link ...............................................................15
7.2 Viewing the Data ............................................................15
7.3 Adjusting the Settings .....................................................16
7.4 Analysis of B-Scans ........................................................16
7.5 Exporting Data .................................................................17
7.6 Further Functions ............................................................17
Page 5
© 2014 Proceq SA 5
1. Safety and Liability
1.1 General Information
This manual contains important information on the safety, use and maintenance of the Pundit PL-200PE. Read through the manual carefully before the first use of the instrument. Keep the manual in a safe place for
future reference.
1.2 Liability
Our “General Terms and Conditions of Sales and Delivery” apply in all
cases. Warranty and liability claims arising from personal injury and damage to property cannot be upheld if they are due to one or more of the
following causes:
• Failure to use the instrument in accordance with its designated use as
described in this manual.
• Incorrect performance check for operation and maintenance of the instrument and its components.
• Failure to adhere to the sections of the manual dealing with the performance check, operation and maintenance of the instrument and its
components.
• Unauthorised modifications to the instrument and its components.
• Serious damage resulting from the effects of foreign bodies, accidents,
vandalism and force majeure
All information contained in this documentation is presented in good faith
and believed to be correct. Proceq SA makes no warranties and excludes
all liability as to the completeness and/or accuracy of the information.
1.3 Safety Instructions
The equipment is not allowed to be operated by children or anyone under
the influence of alcohol, drugs or pharmaceutical preparations. Anyone
who is not familiar with this manual must be supervised when using the
equipment.
• Carry out the stipulated maintenance properly and at the correct time.
• Following completion of the maintenance tasks, perform a functional
check.
1.4 Correct Usage
• The instrument is only to be used for its designated purpose as describe herein.
• Replace faulty components only with original replacement parts from
Proceq.
• Accessories should only be installed or connected to the instrument
if they are expressly authorized by Proceq. If other accessories are
installed or connected to the instrument then Proceq will accept no
liability and the product guarantee is forfeit.
Page 6
6 © 2014 Proceq SA
2. Technical Specifications
Pundit PL-200 Pundit PL-200PE
Range
0.1 – 7930 μs
Resolution
0.1 μs (< 793 μs), 1 μs (> 793 μs)
Display
7” colour display 800x480 pixels
Pulse Voltage UPV
100 – 450 Vpp
UPE
– 100 – 400 Vpp
Bandwidth
20 – 500 kHz
Receiver Gain
1x – 10’000x (0 – 80dB) [11 steps]
Memory
Internal 8 GB Flash memory
Regional Settings
Metric and imperial units and multi-language
supported
Battery
Lithium Polymer, 3.6 V, 14.0 Ah
Battery Lifetime
> 8h (in standard operating mode)
Operating
Temperature
0°C – 30°C (Charging, running instrument)
0°C – 40°C (Charging, instrument is off)
-10°C – 50°C (Non-charging)
Humidity
< 95 % RH, non condensing
IP Classification
IP54
Pulse Echo Range
0.1 – 1200 μs
Transducer
Frequency
50 kHz
Aperture Size
2x25 cm
2
3. Operation
The information provided in this manual covers the Pulse Echo application
only. The Pundit PL-200PE also supports all functionality provided by the
Pundit PL-200. It is necessary to purchase the BNC adapter cable (Part
No. 327 01 049) for operation with standard P-wave transducers. A full
listing of the standard transducers can be found on the Proceq website.
The Pundit PL-200 operating manual is provided on the product DVD.
3.1 Getting Started
Battery Installation
To install the Battery (B) into the Pundit Touchscreen (A), lift the stand as
shown. Insert the battery and fasten in place with the screw.
There are three status LEDs
1
(see page page 3). The middle LED is
red while charging and turns to green when fully charged. The other LEDs
are application specific.
NOTE! Only use the battery charger provided.
Page 7
© 2014 Proceq SA 7
• A complete charge requires <9h (Instrument not operating).
• Charging time is much longer if the instrument is in use.
• An optional quick charger (Part No. 327 01 053) can be used to charge
a spare battery outside of the instrument. In this case it takes <4h for
a complete charge.
Energy Saving
Energy saving, time to dim display and time to turn off display, may be
programmed as desired under System/Power settings.
Connecting the transducer
(D)
Connect the Pulse Echo Transducer (C) to the Pundit Touchscreen (A)
using the Pulse Echo Cable (D).
Buttons
Lift the protective visor.
The upper right of the screen there are three buttons
2
(see page 3).
Power On/Off – Press to power on. Press and hold to power off.
Soft Key – Switches in and out of full screen view.
Back Button – Returns to previous screen.
3.2 Main Menu
On start up the main menu is displayed. All functions may be accessed
directly via the touchscreen. Return to the previous menu by pressing the
back button or the return icon (arrow) at the top left of the touchscreen.
Measurement:
Application specific measurement screen.
Settings:
For application specific settings.
Explorer:
File manager functionality for reviewing measurements saved on the instrument.
System:
For system settings, eg. language, display options,
power saving
Information:
For device information.
Exit:
Power Off.
3.3 Settings
Scroll up and down the screen by dragging your finger up or down the
screen. The current setting is displayed on the right hand side. Tap on an
item to adjust it.
Transducer
Connected Transducer
If a Pulse Echo Transducer is connected this will be recognized automatically.
Test Transducer
Each individual dry contact transducer can be tested for correct functionality.
The graphic on the right hand side of the screen indicates which transducer pair is to be tested (blue highlight). Press the Pulse Echo Contact
Page 8
8 © 2014 Proceq SA
Tester (E) onto the transducer pair as shown.
A successful test is indicated by the
transducer pair being highlighted green.
The next pair to be tested is then highlighted blue.
Continue until each transducer pair has
been tested.
If one contact pair fails the test, it may
be repeated before continuing.
B-Scan
Distance between measurements
Set the spacing between measurements. For good resolution images,
a spacing of 1 cm is recommended. For a quicker initial scan a coarser
spacing may be used, e. g. 2.5 cm corresponding to the spacing markers
on the Pulse Echo Transducer. When searching for larger objects such as
delaminations or thickness variations, much coarser grid spacings may
be used, e. g. 10 cm and upwards.
2.5 cm
Units
Choose between metric and imperial units
Echo Tracking
This is particularly useful if a quick read-out of slab thickness is desired.
For complex objects containing internal defects, pipes and rebars it is
recommended to perform a complete B-Scan for analysis of the object.
Filter
Filters are used to filter out unwanted noise, to make it easier to identify
the correct echo.
• OFF – No filter is applied. The raw signal is displayed.
• Normal – Applies a medium band filter to the received signal.
The received signal is saved post-filtering, so it is not possible to alter the
filter afterwards. Switching the filter off allows the raw data to be viewed.
Time Gain Compensation
When switched on amplifies signals that are further away from the transducer.
Envelope
When this setting is activated it uses an envelope of the A-Scan to generate the B-Scan image. This can also help to generate a clearer B-Scan
image.
Color Range and Color Scheme
Color range may be automatic or manual. When set to manual, the color
gain icon
9
appears on the measurement screen.
Four different color schemes may be chosen according to preference.
Page 9
© 2014 Proceq SA 9
Original – Original signal is used to generate the B-Scan.
Envelope – Envelope signals is used to generate the B-Scan.
SAFT
When activated, applies a Synthetic Aperture Focusing Technique to the
raw data to produce a sharper image.
SAFT uses path length and positioning information to correct the image.
The quality of the final image is dependent on the spacing of the measurements.
3.4 Measurement Screen
The standard measurement screen is shown on page 3. All settings
are directly accessible from the measurement screen.
Zoom
Zoom in by placing thumb and index finger together on the
screen and spreading them apart. This can be used in both the
horizontal and vertical directions when making a measurement.
Zoom out by placing thumb and index finger apart on the
screen and pinching them together.
Pan
Pan the image from left to right by dragging.
Measuring screen controls (see page 3)
1
Filename: Enter the file name and press return. Saved measure-
ments will be stored with this file name. If several measurements are
made under the same file name, a suffix increments after each measurement.
2
Measurement mode: Select the type of measurement to be carried
out (see section “3.5 Measurement Modes”).
3
The top right hand corner of the display shows the current trans-
ducer selected, current time and the battery status.
4
Gain: Adjust the receiver gain, from 1x up to a maximum of 10 000x.
5
Voltage: Adjust the transmitter voltage. For best results, it is best to
begin with low transmitter voltage and a low gain setting. Then increase
until a stable signal level is achieved. Signal clipping should be avoided.
Page 10
10 © 2014 Proceq SA
6
Settings: Enter the settings menu.
7
Stop/Save (Right Button on Transducer):
Stop the current measurement.
Save the current measurement.
Save the current series and continue the measurement.
8
Start/Snapshot (Left Button on Transducer):
Begin the measurement.
Save the current measurement as displayed on the
screen and continue measuring.
L
R
9
Cursor Selection
Automatic triggering.
Manual triggering. Set the cursor position manually, by
dragging it to the left or right. The trigger position may
also be adjusted later on the saved waveform in the
Explorer or in PL-Link.
Available in transmission time mode only. Allows a
marker to be set on a second echo and the difference
between thet two echos is displayed.
Manually adjust the colour intensity.
10
Automatic Estimation of Pulse Velocity
This setting is available in the Distance and B-Scan
modes. The pulse velocity may be entered manually after having made a control measurement on an
object of known thickness. Alternatively, it is possible
to estimate the pulse velocity directly on surface of the
test object. Tap on this button and press the transducer
against the surface to make a measurement. A number
of measurements can be made and an average value
is calculated. Tap to apply the pulse velocity setting. Pulse velocity may be subsequently adjusted on
saved files in the Explorer or in PL-Link.
NOTE! Typical shear wave pulse velocities for concrete are in
the region 2000 - 2500 m/s
Page 11
© 2014 Proceq SA 11
3.5 Measurement Modes
Transmission time
The measured transmission time between the transmitter and receiver.
Distance
Enter the pulse velocity of the material under test or perform an “Automatic Estimation of Pulse Velocity” as described in the previous chapter.
The result is the thickness of the slab or distance to the internal object
(e. g. void, delamination) that is the source of the echo.
Pulse Velocity
Enter the thickness of the object under test.
The result is the transmission time and pulse velocity of the material under test.
B-Scan
Provides a cross sectional image of the test object perpendicular to the
scanning surface in the plane through which the individual A-scans have
been collected.
The spacing between A-Scans is entered in the “Settings” menu.
Position the transducer at the starting position.
Press the start icon to begin or the left button on the
transducer.
Record the first measurement. The measurement may
also be recorded by pressing the left button on the
transducer.
• The LED’s on the transducer provide a visual feedback when a measurement has taken place successfully. This is accompanied by an
acoustic tone on the display device. The volume of the tone may be
adjusted in system settings.
• Move the transducers to the next point of the scan. Make the second
measurement and continue.
• The current A-Scan is shown on the right hand side of the screen.
• The current status of the B-Scan is shown on the main part of the
screen.
Press this icon or the right button on the transducer to
save the current B-Scan.
Press this icon or the right button on the transducer to
continue the current B-Scan.
Use this icon to delete the last measurement made.
Press the to save the current series and reset the instrument for a new series.
The green cursor (cross-hairs) may be moved to any point on the B-Scan
simply by dragging. The actually cursor position is displayed on the axes.
The current A-Scan selected changes with the cursor position. This is
indicated by the A-Scan number at the top of the chart and also on the
A-Scan display at the right side of the measurement screen. This feature
is also available on saved B-Scans in the Explorer or in PL-Link.
Page 12
12 © 2014 Proceq SA
3.6 Measuring with Pundit PL-200PE
NOTE! Testing with Pulse Echo Technology requires in-depth
knowledge of the test object and application characteristics.
Proceq offers comprehensive ultrasonic training seminars
imparting this knowledge as well as all functionalities and
features of the Pundit instruments. Pundit PL-200PE users
are recommended by Proceq to register for the Advanced
Ultrasonic Tomography Applications training. Details can be
found on the Proceq website.
Preparation
• Very few preparations are necessary when measuring with the Pulse
Echo Transducer.
• The dry-contact transducer means that acoustic coupling is ensured
without the use of any couplant.
• The contacts are sprung and can accommodate surface irregularities
to a depth of 7 mm, so smoothing of the surface is also unnecessary.
• For B-Scans a test grid should be drawn out on the surface. Alternatively Proceq provide a calibrated tape (Part No. 327 010 71) that can
be stuck on the surface for the test and then removed afterwards.
Calibration
The most accurate results can be obtained if the instrument is calibrated
for the material under test.
• This is done by performing a pulse velocity measurement on a section
of the structure of known thickness.
• Alternatively, perform the automatic estimation of pulse velocity as described in chapter 3.4.
Physical influences on the Measurement
Inhomogeneities (e. g. aggregate particles, voids) in concrete influence
the propagation of an ultrasound pulse. They will scatter the signal. The
effect is very large if the size of the aggregate is equal to or larger than the
wavelength of the ultrasonic signal. This influence is significantly reduced
when the wavelength is at least twice as large as the aggregate size. It
also follows that it is very difficult to detect an anomaly if it is smaller than
half the wavelength.
The Pulse Echo Transducer is a shear wave transducer with a frequency
of 50 kHz.
Assuming a typical pulse velocity of 2500 m/s, the wavelength is 50 mm.
This means that anomalies smaller than 25 mm will be invisible.
Effect of sample size
The geometry of the object is very important for obtaining good results.
• The maximum penetration depth depends on the quality of the concrete and also on the amount of rebars present. Typically the maximum
transmission depth lies between 50 cm (19.7”) and 1m (39.4”).
• Generally, the minimum lateral dimension should be two times the
thickness of the object, or the depth of the anomaly you are trying to
detect. The reason for this is that if the object is too narrow, reflections
from the side walls will interfere with the echo from the rear wall.
4. Explorer
From the main menu select Explorer to review saved files.
Tap on a saved file to open it.
Return to the Explorer list by pressing the back button.
To delete a file tap in the check box
to the left of the file and delete it
Page 13
© 2014 Proceq SA 13
4.1 Analysis of B-Scans
Please refer to the separate booklet Pundit PL-200PE B-Scan Measurement Examples.
Explorer provides a number of tools that assist in the analysis of B-Scans.
• Drag the cross hairs to a point of interest. (e. g. back wall of sample
as shown here)
• The object thickness (e. g. 0.3m) is displayed on the y-axis.
• The object position from the beginning of the scan is displayed on the
x-axis.
• The current A-Scan (e. g. #22) is indicated above the B-Scan and also
in the the A-Scan window.
• The current transmission time is displayed at the right hand side of the
of the screen.
• The cursor position may also be adjusted by dragging on the position
display boxes.
• SAFT and Envelope may be switched ON/OFF in Settings.
• Pulse velocity may be corrected.
• Spacing between measurements may be corrected.
• The color scheme may be adjusted.
• Any modifications made to the scan may be saved.
• All of these items may be adjusted later in PL-Link once the files have
been downloaded to a PC.
5. Ordering Information
5.1 Units
PART NO. DESCRIPTION
327 10 002 Pundit Touchscreen without transducers
Consisting of: Pundit Touchscreen, BNC adapter cable,
battery charger, USB cable, DVD with software, documentation, carrying strap and carrying case
327 10 001
Pundit PL-200
Consisting of: Pundit Touchscreen, 2 Transducers 54 kHz,
2 BNC cables 1.5 m, couplant, calibration rod, BNC
adapter cable, battery charger, USB cable, DVD with software, documentation, carrying strap and carrying case
327 20 001 Pundit PL-200PE
Consisting of: Pundit Touchscreen, Pundit Pulse Echo
Transducer incl. cable, contact tester, battery charger,
USB cable, calibrated tape, DVD with software, documentation, carrying straps and carrying case
5.2 Transducers
PART NO. DESCRIPTION
325 40 026S 2 Transducers 24 kHz
325 40 131S 2 Transducers 54 kHz
325 40 141S 2 Transducers 150 kHz
325 40 177S 2 Transducers 250 kHz
325 40 175S 2 Transducers 500 kHz
325 40 176 2 Exponential Transducers 54 kHz, incl. calibration rod
325 40 049 2 S-Wave Transducers 250 kHz, incl. couplant
327 40 130 Pulse Echo Transducer, incl. cable and contact tester
Page 14
14 © 2014 Proceq SA
5.3 Accessories
PART NO. DESCRIPTION
327 01 043 Carrying strap complete
325 40 150 Transducer holder complete
327 01 049 BNC adapter cable for Pundit PL-200
325 40 021 Cable with BNC-plug, 1.5 m (5 ft)
325 40 022 Cable with BNC-plug, 10 m (33 ft)
710 10 031 Ultrasound couplant, 250 ml
325 40 048 Shear wave couplant, 100 g
327 01 033 Battery complete
327 01 053 Quick charger
710 10 028 Calibration rod 25 μs for Pundit PL-200
710 10 029 Calibration rod 100 μs for Pundit PL-200
327 01 070 Snap Ferrite for BNC Adapter cable*
327 01 051 Pundit Pulse Echo Cable
327 00 027 Pundit Pulse Echo Contact Tester complete
327 20 002 Pundit PL-200PE UPV Kit including BNC adapter cable,
2x cable with BNC-plug, L=1.5m (5ft), Ultrasound couplant, 250ml bottle, 2 transducers 54 kHz, calibration rod
327 01 071S Calibrated Tape (Set of 5)
* In the case that receiving equipment within a radius of 10m suffers from interference, it is possible to order a ferrite to fit onto the BNC adapter cable. This serves
to further reduce the electromagnetic radiation produced by the instrument.
6. Maintenance and Support
6.1 Maintenance
To guarantee consistent, reliable and accurate measurements, the instrument should be calibrated on a yearly basis. The customer may however,
determine the service interval based on his or her own experience and
usage.
6.2 Support Concept
Proceq is committed to providing a complete support service for
this instrument by means of our global service and support facilities. It is recommended that the user register the product on
www.proceq.com to obtain the latest on available updates.
6.3 Warranty Information
Each instrument is backed by the standard Proceq warranty and extended warranty options.
• Electronic portion of the instrument: 24 months
• Mechanical portion of the instrument: 6 months
6.4 Disposal
Disposal of electric appliances together with household waste is not
permissible. In observance of European Directives 2002/96/EC,
2006/66/EC and 2012/19/EC on waste, electrical and electronic equipment and its implementation, in accordance with national law, electric
tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Page 15
© 2014 Proceq SA 15
7. PL-Link Software
7.1 Starting PL-Link
Locate the file “PL-Link Setup.exe” on your computer or on
the CD and click on it. Follow the instructions on the screen.
Make sure that the “Launch USB Driver install”
tick is selected.
The USB driver installs a virtual com port which is
needed to communicate with the Pundit Touchscreen Unit.
Double click on the PL-Link Icon on your desktop or start the PL-Link
via the start menu.
The PL-Link starts with a blank list.
Application settings
The menu item “File – Application settings” allows the user to select the
language and the date and time format to be used.
Connecting to a Pundit Touchscreen Unit
Connect the Pundit Touchscreen Unit to a USB port, then select the following icon to download data from the Pundit Touchscreen Unit.
The following window will be displayed: Select “USB” as the communication type.
Select one or more measurements and click “Download”.
Click on “Next >”. When a Pundit Touchscreen Unit has been found its details
will be displayed on screen. Click on the
“Finish” button to establish the connection.
7.2 Viewing the Data
Measurement files stored on the device will be displayed in the following
window:
Select one or more measurements and click “Download”.
The selected measurements on your Pundit Touchscreen Unit will be displayed on the screen:
Page 16
16 © 2014 Proceq SA
Click on the double arrow icon in the first column to see more details:
NOTE! Click on “Add” to attach a comment to the object.
7.3 Adjusting the Settings
Each of the settings that were used in the Pundit Touchscreen Unit at
the time of the measurement series can be adjusted subsequently in PLLink. This can be done either by right clicking directly on the item in the
appropriate column, or by clicking on the blue setting item in the detailed
view of a measurement object.
In each case a drop down selection box will appear with the choice of
setting.
7.4 Analysis of B-Scans
PL-Link provides a number of tools that assist in the analysis of B-Scans.
• Zoom into the B-Scan using the zoom boxes. A separate zoom box is
available for the currently selected A-Scan
• Move the B-Scan in both x- and y-directions by dragging with the left
mouse button.
• Move the A-Scan in the y-direction by dragging with the left mouse
button.
• Drag the cross hairs to a point of interest using the right mouse button.
The position is shown in the details on the right hand side.
• The current A-Scan (e. g. #22) is indicated in the table.
Adjusting the date and time
Right click in the “Date & Time” column.
Page 17
© 2014 Proceq SA 17
The time will be adjusted for the selected series only.
In “Data Logging” mode it is the date and time at which the measurement
was made.
7.5 Exporting Data
PL-Link allows you to export selected objects or the entire project for use
in third party programs. Click on the measurement object you wish to
export. It will be highlighted as shown.
Click on the “Export as CSV file(s)” icon. The data for this
measurement object is exported as a Microsoft Office Excel
comma separated file or files. The export options may be
chosen in the following window:
Click on the “Export as graphic” icon to open the following
window which allows the various export options to be chosen.
In both cases, the preview window shows the effects of the current output selection.
Finish by clicking on export to select the file location, name the file and
in the case of a graphical output to set the output graphic format: .png,
.bmp or .jpg
7.6 Further Functions
The following menu items are available via the icons at the top of the
screen:
“PQUpgrade” icon - Allows you to upgrade your firmware via
the internet or from local files.
“Open project” icon – Allows you to open a previously saved
.pql project.
“Save project” icon – Allows you to save the current project.
“Print” icon – Allows you to print out the project. You may
select in the printer dialog, if you want to print out all of the
data or selected readings only.
Clicking “Auto Scale” adjusts the zoom parameters of the
waveform display to an optimum setting.
Page 18
Made in Switzerland
Subject to change. Copyright © 2014 by Proceq SA, Schwerzenbach. All rights reserved.
820 327 03E ver 05 2014
Proceq Europe
Ringstrasse 2
CH-8603 Schwerzenbach
Phone +41-43-355 38 00
Fax +41-43-355 38 12
info-europe@proceq.com
Proceq UK Ltd.
Bedford i-lab, Priory Business Park
Stannard Way
Bedford MK44 3RZ
United Kingdom
Phone +44-12-3483-4515
info-uk@proceq.com
Proceq USA, Inc.
117 Corporation Drive
Aliquippa, PA 15001
Phone +1-724-512-0330
Fax +1-724-512-0331
info-usa@proceq.com
Proceq Asia Pte Ltd
12 New Industrial Road
#02-02A Morningstar Centre
Singapore 536202
Phone +65-6382-3966
Fax +65-6382-3307
info-asia@proceq.com
Proceq Rus LLC
Ul. Optikov 4
korp. 2, lit. A, Office 410
197374 St. Petersburg
Russia
Phone/Fax + 7 812 448 35 00
info-russia@proceq.com
Proceq Middle East
P. O. Box 8365, SAIF Zone,
Sharjah, United Arab Emirates
Phone +971-6-557-8505
Fax +971-6-557-8606
info-middleeast@proceq.com
Proceq SAO Ltd.
South American Operations
Alameda Jaú, 1905, cj 54
Jardim Paulista, São Paulo
Brasil Cep. 01420-007
Phone +55 11 3083 38 89
info-southamerica@proceq.com
Proceq China
Unit B, 19th Floor
Five Continent International Mansion, No. 807
Zhao Jia Bang Road
Shanghai 200032
Phone +86 21-63177479
Fax +86 21 63175015
info-china@proceq.com
Loading...