Proceq PaperSchmidt, 342 10 000 Operating Instructions Manual
... more than 50 years of know-how you can measure!
Made in Switzerland
Operating Instructions
Paper Roll Hardness Tester
Operating Instructions
1. Getting Started 3
2. Safety and Liability 4
2.1 General Information 4
2.2 Liability 4
2.3 Safety Instructions 4
2.4 Correct Usage 4
3. Real Tests 5
3.1 Preparation 6
3.2 Define a Roll ID for the Test Series 6
3.3 Measure the Roll Hardness Profile 7
3.4 Terminate the Series and review 7
3.5 Entering a Roll ID manually 8
3.6 Accept or modify limits 8
3.7 Review list 9
4. Technical Specifications 9
5 Part Numbers and Accessories 10
5.1 Units 10
5.2 Parts and Accessories 10
6. Maintenance and Support 10
6.1 Self test function 10
6.2 Checking the calibration on the anvil 10
6.3 Support Concept 10
6.4 Standard Warranty and Extended Warranty 10
7 Paperlink Software 11
7.1 Starting Paperlink 11
7.2 Viewing the data 11
7.3 Adjusting the max/min settings 13
7.4 Adjusting the date and time 13
7.5 Exporting data 13
7.6 Deleting and restoring data 14
7.7 Further Functions 14
7.8 Pre-define Roll IDs 15
7.9 Technical Information Paperlink software 15
3 © 2009 by Proceq SA
1. Getting Started
Note: First time user: Complete the tutorial OR see a demo by a qualified Proceq
representative. If you only need to do simple measurements, please go to chapter
3.3.
Charging the PaperSchmidt
The PaperSchmidt uses a built-in Lithium Polymer accumulator. In case of a low battery alert, you
can still record approximately 100 to 200 impacts. When the display indicates a low battery, connect
the PaperSchmidt to the charger or to a PC. Approximately 90 minutes of charging will bring your
PaperSchmidt to its full capacity. The PaperSchmidt can be recharged at any time.
Power ON
Press the SELECT button to power on.
Plunger USB port LC Display SELECT button
Check the calibration of the hammer
Perform a calibration check on your hammer as described in chapter 6.
Congratulations! Your new PaperSchmidt is fully operational and you can now continue with your
measurements.
Performing a reset
In case a reset is required, this can be done by performing an impact with the select button
pressed.
Note: This will remove any lower and upper limits that may have been set.
Note: Should your instrument be fully discharged, start with a reset after recharging.
Power OFF
The PaperSchmidt will shut down automatically after 5 minutes of inactivity.
Standards and Regulations Applied
The following standard has been applied in the PaperSchmidt.
TAPPI T 834 om-07 (Determination of containerboard roll hardness)
The following recommendation has been taken into consideration in the PaperSchmidt.
TAPPI TIP 1004-01 (TAPPI Roll Number for inventory/tracking systems and bar codes)
This standard recommends a 12 digit roll number. The PaperSchmidt is able to accept roll identifier
names (Roll IDs) in this format.
4 © 2009 by Proceq SA
2. Safety and Liability
2.1 General Information
This manual contains important information on the safety, use and maintenance of the PaperSchmidt.
Read through the manual carefully before the first use of the instrument. Keep the manual in a safe
place for future reference.
2.2 Liability
Our “General Terms and Conditions of Sales and Delivery” apply in all cases. Warranty and liability
claims arising from personal injury and damage to property cannot be upheld if they are due to one
or more of the following causes:
Failure to use the instrument in accordance with its designated use as described in this manual.•
Incorrect performance check for operation and maintenance of the instrument and its compo-•
nents.
Failure to adhere to the sections of the manual dealing with the performance check, operation •
and maintenance of the instrument and its components.
Unauthorised modifications to the instrument and its components. •
Serious damage resulting from the effects of foreign bodies, accidents, vandalism and force •
majeure.
All information contained in this documentation is presented in good faith and believed to be correct.
Proceq SA makes no warranties and excludes all liability as to the completeness and/or accuracy of
the information.
2.3 Safety Instructions
The equipment is not allowed to be operated by children or anyone under the influence of alcohol,
drugs or pharmaceutical preparations. Anyone who is not familiar with this manual must be supervised when using the equipment.
Carry out the stipulated maintenance properly and at the correct time. •
Following completion of the maintenance tasks, perform a functional check.•
2.4 Correct Usage
The instrument is only to be used to determine the roll hardness profile of paper and film rolls.•
Replace faulty components only with original replacement parts from Proceq.•
Accessories should only be installed or connected to the instrument if they are expressly autho-•
rized by Proceq. If other accessories are installed or connected to the instrument then Proceq will
accept no liability and the product guarantee is forfeit.
5 © 2009 by Proceq SA
3. Real Tests
3.6 Accept or modify limits
C omplete G etting S tarted
7.8 Pre-define R oll IDs in
P aperlink a nd download to
hammer
Method 1: P erform a n
impact (Roll ID = Counter)
Method 2: Ma nually
enter R oll ID
Method 3: S e le ct a pre-
defined R oll ID
3.3 Meas ure the R oll H ardness Profile
3.4 T erminate the S eries and review
3.1 Preparation
3.2 Define a R oll ID for the T es t S eries
Loading...