Probuilt Professional Lighting Wobblelight User Manual
Manufactured by ProBuilt Professional Lighting: 877-707-0800
Thank you for purchasing Wobblelight® WL85F
IMPORTANT SAFETY INSTRUCTIONS
WARNING !!!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS
QUESTIONS OR PROBLEMS?
Call ProBuilt Professional Lighting Customer Service and Technical Support at 877-707-0800 (Monday-Friday from 8:30 a.m. until 5 p.m. Central
time) or e-mail customerservice@probuiltlighting.com
This manual contains important safety and operating instructions for Wobblelight® WL85F portable lighting. Before using Wobblelight® WL85F please review all of
the following safety instructions carefully and read all labels on the Wobblelight
INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS:
WARNING: To reduce the risk of fire, electric shock, or injury to persons:
DO NOT connect Wobblelight® WL85F to power source until the bulb is installed and the unit is completely assembled.
DO NOT attempt to remove the protective lens to change bulbs unless the Wobblelight
has completely cooled.
Not for use in wet locations. DO NOT use Wobblelight
spray or standing water.
Connect Wobblelight
protection which is rated no higher than 15 amps. Any other connection voids warranty and may result in damage to the product, fire, property damage
and injury.
Keep away from flammable materials.
Wobblelight
®
WL85F must be operated in the upright position only. DO NOT mount Wobblelight® WL85F units upside down or restrain them such that
they lay on their side.
Use only approved extension cords in good condition and of the appropriate type, gauge and length.
Keep extensions cords dry and use ground fault circuit interrupter (GCFI) devices in accordance with all applicable electrical code requirements.
®
WL85F only to 120 volt, 60 Hz power source which is protected with a ground-fault circuit interrupter (GFCI) and over-current
anytime.
®
WL85F unit.
®
WL85F unit is disconnected from the power source and the bulb
®
WL85F where there is potential for exposure to excessive moisture from rain, snow, ice, water
DO NOT operate Wobblelight® WL85F units with the protective dome and cap missing or broken. DO NOT use Wobblelight® WL85F units with a broken
housing or damaged electrical cord. Take any damaged units out of service immediately. Replacement bulbs and parts are available from ProBuilt
Professional Lighting or a local authorized distributor or retailer.
Use ONLY designated replacement bulbs of the appropriate type and wattage.
DO NOT expose Wobblelight
DO NOT expose Wobblelight
Disassembly (other than re-lamping) of Wobblelight
®
WL85F to intense heat or sparks from welding slag, cutting torches, metal saws, etc.
®
WL85F to corrosive chemicals, excessive paint spray or abrasive blasting materials.
®
WL85F will void the warranty. Contact ProBuilt Professional Lighting or a local authorized service
center for repairs and replacement parts.
DO NOT remove silicone bumpers from fluorescent lamp tubes.
Avoid excessive bumping and bouncing during operation since mechanical shock can cause shattering of the fluorescent lamp.
Always operate the lamp with the Wobblelight
®
WL85F dome/cap assembly in place to prevent personal injury or property damage.
Install and remove lamp by grasping the plastic base only.
WARNING: Deviation from these instructions may result in the increased risk of fire, electric shock, injury to persons or property damage.
The Wobblelight
intended for use with emergency exit fixtures or emergency exit lights.
®
85-watt compact fluorescent bulb is self-ballasted and must not be used in any other fluorescent fixture with an external starter or ballast. This device is not
RE-LAMPING AND ASSEMBLY INSTRUCTIONS
Your Wobblelight® WL85F carton should include the following parts:
Wobblelight
®
WL85F fixture.
Dome / cap assembly.
Lamp (85-watt self-ballasted fluorescent bulb).
Dome screw packet containing four (4) screws (1/4” x 5/8” Phillips button-head sheet metal screw).
If there are any parts missing or damaged, DO NOT contact your Wobblelight® retailer. Please contact ProBuilt Professional Lighting
Customer Service toll-free at 877-707-0800.
Instructions for Wobblelight
1. Remove and verify the contents of your Wobblelight
2. Install the bulb into the socket by screwing the lamp firmly but not forcibly into socket in order to avoid breakage.
3. Grasp bulb by the plastic base and not the glass tubes. DO NOT REMOVE SILICONE BUMPERS which are in place to protect the bulb from breakage.
4. Tighten bulb until it is secure in the socket – do not over tighten.
5. Install the Wobblelight® WL85F dome / cap assembly by aligning the four mounting holes with the four mounting nuts (note that the dome handle should be aligned with the
Wobblelight
6. Secure dome with the four mounting screws – do not over tighten.
7. Your assembled Wobblelight
8. Use only Wobblelight
®
logo). The fit will be snug, but the dome will slide over the four mounting nuts if properly aligned.
®
WL85F assembly:
®
®
WL85F is now ready for use.
WL85F replacement bulbs.
®
WL85F carton.
OPERATION and USE OF Wobblelight® WL85F
Loading...