Probuilt Professional Lighting Uplight User Manual

Uplight v2

Safety, operation & maintenance instructions

CONTENTS

Ground Fault Interrupter (GFI) Page 2

Important Safety Information Page 2-3

Electrical Safety Guidelines Page 3-4

Getting Uplight v2 Started Page 4-5

Self-Righting Properties Page 6

6 egaPsnoitceriD gnikniL

Lighting Tube Replacement Page 7

Cleaning Page 7

Service Recommendations Page 7

Questions & Answers Page 8

Replacement Parts Page 8

What Uplight v2 Can Be Used For Page 8

Product Specification Page 8

9 egaPeetnarauG

9 egaPyciloP eetnarauG

Parts Diagram Page 10

Parts List Page 11

Certificate of Conformity Page 12

THANK YOU FOR BUYING UPLIGHT v2

You should read the entire operator’s manual before you use your Uplight v2 and you should
restrict its use to persons who have read, understood, and who will follow all warnings and
instructions contained in this manual. In addition, you should follow all warnings and
instructions affixed to your Uplight v2.

IMPORTANT SAFETY INFORMATION

The safety of this appliance complies with current safety regulations and with applicable
directives. Should you have any queries relating to the safe operation of your Uplight v2,
please refer to your Defender vendor or tool hire agent.

Please read these instructions carefully prior to using this product. There is a possible risk of
personal injury if you fail to follow the advice laid down in this guide.

After use, ensure that these instructions are stored in a safe place for future reference.

ESSENTIAL SAFETY INSTRUCTIONS TO NOTE:

• UPLIGHT v2 should only be used by a competent person, who has read and understood
these instructions. If in doubt, please refer to a suitably qualified person.

• UPLIGHT v2 must not be modified in any way. Alterations of any description may
invalidate the product warranty and technical approvals.

• UPLIGHT v2 must only be used
(refer to the ‘What Uplight v2 Can Be Used For’ section).

• Never use this equipment if you are ill, feeling tired, or under the
influence of alcohol or drugs.

• Always switch OFF at power supply and unplug the unit when not in use
and prior to cleaning.

• Always unplug the unit from the power supply before moving or repositioning it.

• Ensure the cable is coiled to prevent a trip hazard when repositioning.

• Always ensure that the unit has cooled completely before storing it.

• Do not work near flammable gases or liquids.

• Make sure that you know how to switch this unit OFF before you switch it ON.

• Keep power cord(s) out of harm’s way and clear of the work area.

• Keep Uplight v2 dry wherever possible.

• Never leave the unit in use without supervision.

• Do not use if the unit or the power cord appears to be damaged.

• Do not place the unit near a source of heat.

for its intended purpose

• If the unit is to be positioned horizontally on the ground ensure it does not pose a
trip hazard.

• If the Uplight v2 is to be used whilst propped against a vertical surface, ensure the unit is
positioned on its rubber base.

• If Uplight v2 is suspended only use the fixing point on the unit.
If the removable eyelets are used ensure they are connected to the correct anchorage
points and ensure nothing else is suspended on the unit.

• Ensure the mains cable does not present a trip hazard. Do not run cable across
walkways. Once the cable has been routed secure cable in position.

• Ensure the mains power cable is fully unwound before use.

• Do not remove plug from mains supply by pulling on power cord.

ELECTRICAL SAFETY GUIDELINES

PLEASE COMPLY WITH THE SPECIFIED ELECTRICAL REQUIREMENTS.

Power Supply Identification
The power supply of this UPLIGHT v2 unit is shown on the identification label and the rating
plate, which are found on the external packaging and the base of the unit respectively.

Model Numbers

110Volt
Uplight v2 2ft (18Watt) E712505
Uplight v2 4ft (36Watt) E712500