Page 1
FUSION LED
WALLPACK/
FLOOD LIGHT KIT
INSTALLATION,
USAGE, & CARE GUIDE
Model No.
Mfr. SKU
FSN50-PC-4K-BZ
103-08400001-1
Questions? / Missing Parts? / Need Accessories?
Before returning to the store, call or email PROBRITE
Customer Service 9am-5pm EST Monday to Friday.
1-844-507-5651
PROBRITE.COM
Visit us online anytime or call us to get information on our product range, download
detailed spec & photometric files, find product and mounting accessories, view
installation tutorials and videos, and learn about our DLC® rebate eligible products.
Page 2
Table of Contents
Pre-Installation
Table of Contents......................... 2
Safety Information........................ 2
Pre-Installation.............................. 3
Planning Installation...................... 3
Specifications.................................. 3
Tools Required................................ 3
Package Contents......................... 4
Installation..................................... 5
Operation......................................10
Troubleshooting............................11
Care & Cleaning............................12
Warranty.........................................12
Hardware Included........................ 4
Safety Information
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
NATIONAL ELECTRICAL CODE AND LOCAL BUILDING CODES BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
PRECAUTIONS
☐ Please read and understand this entire
manual before attempting to assemble,
install, or operate this light fixture.
☐ This light fixture requires a 120-277Volt
AC power source.
☐ Some codes require installation by a
qualified electrician.
☐ This light fixture must be properly
grounded.
☐ Make sure connections are secure using
wire nuts, crimp-on lugs or other approved connecting devices
☐ This light fixture should be installed out-
doors to a wall or to the ground.
☐ This product may contain chemicals
known to be hazardous. Thoroughly
wash hands after installing, handling,
cleaning or otherwise touching the
product.
Save these instructions
WARNING: Turn the power o at the circuit
breaker or fuse. Place tape over the circuit
breaker switch and verify power is o at the
light fixture.
WARNING: Risk of fire. Keep the lamp heads at
least 3 in. (76mm) from combustible materials.
CAUTION: Burn hazard. Allow the light fixture
to cool before touching.
NOTICE: Do not connect this fixture to a
dimmer switch.
NOTICE: FCC Regulations state that any
unauthorized changes or modifications to
this equipment not expressly approved by the
manufacturer could void the user’s authorization to operate this equipment.
PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the
Hardware Included and Package Contents sections. If any part is missing or damaged, do
not attempt to assemble, install, or operate this light fixture.
Estimated installation time: 20 minutes
SPECIFICATIONS
MODEL FUSION 50W
Lumens (Light Output)
Watts (Power Consumption)
Replaces
Lumens/Watts (Efficacy)
Power Requirements (Input Voltage)
Light Color (CCT)
Dimmable
Operating Modes
5000 Lumens
50 Watts LED
150 Watt Metal Halide
100 lumens per watt
120-277VAC
4000 Kelvins (Bright White)
Non-Dimming (Do not wire to dimming switch)
Dusk-to-Dawn:
Automatically turns light fixture ON during night
and OFF during day.
Switch-Controlled:
Flip switch to turn light fixture ON and OFF. Use
included light sensor cap on fixture's light sensor
to utilize this mode setting.
TOOLS REQUIRED
Phillips
Screwdriver
Silicone
Sealant
Wire strippers/
cutters
Work
gloves
Circuit tester
Ladder
2
Visit www.probrite.com/install for installation video tutorials and product support
Safety
goggles
3
Please call 1-844-507-5651 or email [email protected] for further assistance.
PROBRITE.COM
Page 3
Pre-Installation (continued)
Installation
HARDWARE KIT
NOTE: Hardware not shown to actual size.
AA
Part Description Quantity
#8-32 x 3/4" philips mounting bracket screw 2
AA
Wire nut 3
BB
Allen key 1
CC
DD
Photocell (light sensor) screw-on clear cap 1
BB
CC
PACKAGE CONTENTS
C
H
A
B
Part Description Quantity
Light fixture 1
A
1/2" NPS threaded knuckle mount handle 1
B
Wall/Eave mounting base plate 1
C
Universal junction box mounting plate 1
D
E
Mounting plate hex bolt 2
F
Hands-Free Hooking Wire 1
G
Tightening washer for knuckle mount 1
H
Photocell (light sensor) screw-on opaque cap 1
NOTE: The junction box cover plate is not provided in the box. It is available separately
with your retailer.
G
D
E
For best results
1
☐ Install light 8-20 feet above the ground
for wall applications or on ground for
DD
flood application.
☐ The fixture can be mounted in multiple
ways:
A. Wall/Eave Mount: Using the
wall mounting base (C) and the
mounting plate (D) over a junction
box.
B. Swivel Knuckle Flood Mount: Can
be used with a domed cover plate
(not provided) on a junction box.
☐ When installing two fixtures on one
switch, make sure the switch is rated for
at least a 1A inductive load.
☐ Do NOT wire to a dimming switch.
Mount with
Universal
Junction
Box Wall/
Eave Base
(included)
Eave Mount (A or B Mount)
Mount with 1/2" NPS
Threaded Flood
Mount (Junction box
dome cover plate
with center hole not
included)
Wall Mount (A or B Mount)
F
IMPORTANT INFORMATION: Domed cover
plates for junction boxes, landscape posts,
and other mounting arms and accessories
are available. Please contact your retailer or
PROBRITE's customer support.
Junction box
domed cover
plate with
center hole
Swivel Knuckle Flood Mount (B Mount)
Landscape
Post
Shut electric power off
2
☐ At wall switch verify it is in the o
position (fig 1).
☐ At the main electrical panel turn o
the circuit breaker that supplies power
to the outlet box you are working on
(fig 2).
☐ For screw-in type fuses unscrew the
fuse that supplies power to the outlet
box you are working on (fig 3).
(fig 1).
(fig 2).
(fig 3).
4
Visit www.probrite.com/install for installation video tutorials and product support
5
Please call 1-844-507-5651 or email [email protected] for further assistance.
PROBRITE.COM
Page 4
Installation (continued)
Installation (continued)
Installing Wall/Eave Mount Base
3A
Wall/Eave Mount Base Set Up on Standard Junction Boxes
☐ Using allen key, remove the screw from
the center of the knuckle handle as
shown in fig. 2.
☐ Use the wall mount base plate (C),
provided separately in the box, and
thread wires through the hole of the
plate, being careful not to pinch the
wires.
☐ Place the fixture head in required
orientation with the plate and tighten
the screw on the knuckle which was
removed earlier. (fig. 3).
(Optional if desired)
NOTE: The fixture comes with the knuckle
handle (Fig. 1) and the wall mount base plate
(C) is available separately within the box.
(fig 1).
(fig 3).
Installing with Swivel Knuckle Mount
3B
For Ground and Wall/Eave Mounting
☐ Place wires through the hole in the domed
junction box cover plate or landscape post.
☐ Place tightening washer on back side of
domed cover plate.
☐ Screw 1/2" NPS threaded knuckle mount (B)
into the center hole of the domed plate or
landscape post and, if hole isn't threaded,
use tightening washer (G) to tighten fixture
into place.
☐ Use provided allen key (CC) to loosen
bolt in center of knuckle mount and select
desired angle. Tighten bolt to secure into
place.
For mounting to domed junction box cover plate (sold
separately) or landscape post (sold separately)
NOTE: The fixture comes with the 1/2" threaded
NPS swivel knuckle mount (B) and is compatible
with standard domed junction box cover plates
with a center hole or landscape posts
Remove the
screw here
C
B
B
(fig 2).
(fig 4).
(Domed
junction box
cover plate)
G
(Landscape
post)
4A
Wall / Eave Mount using the base plate
☐ Remove the mounting plate (D) from
the back of the fixture by loosening the
screws using the allen key (CC)(Fig. 1)
☐ Align the holes of the mounting plate
with the "TOP" marking oriented
upwards (or closest to wall if eave
mounted) with the junction box on the
wall and fix the mounting plate (D) on
the junction box by using the two #8
screws (AA). (Fig. 2)
and Fixing it on the Wall/Eave
(Only Applicable for Wall/Eave Mount if using the base plate)
TIP: Only unscrew the tightening bolt (E) far
enough to remove the mounting plate (D).
Do not fully remove the tightening bolt (E).
NOTE: Use any other suitable bolts or fasteners
as applicable to your mounting surface.
Hooking Hands-Free Install Wire
Removing the Mounting Plate from Wall Base
5A
☐ Take the round "ball" head of the
☐ Ensure the fixture can now hang-free
(For install with Wall/Eave Mount Base Plate Only)
hands-free wire (F), attached to back
of base plate, and place it behind the
bottom-center "notch" of the mounting
plate (D)
to allow for hands-free connection of
the electrical wires
NOTE: After electrical connections are made
un-hook the hands-free wire (F) and then
mount the fixture onto the mounting plate (D).
CC
AA
Wall Mount
Wall/Eave Mount
D
D
E
(fig 1).
(fig 2).
TOP
D
F
TOP
D
F
6
Visit www.probrite.com/install for installation video tutorials and product support
7
Please call 1-844-507-5651 or email [email protected] for further assistance.
PROBRITE.COM
Page 5
Installation (continued)
Installation (continued)
Making the electrical
5A/B 7A
☐ If necessary, strip 3/8" of insulation
from junction box or fixture (A) wires
(fig 1).
Wiring Instructions
☐ Connect fixture black wire to house
black wire, the (+) line, and fixture
white wire to house white wire, the (-)
common by twisting the exposed wires
together and using the wire nuts (BB).
Ensure no loose wires.
☐ Connect house ground wire to the
green fixture ground wire, which is
attached to the mounting plate (D), by
twisting the exposed wires together
and using the wire nuts (BB).
TIP: Hold stripped ends near each other and
align any frayed strands (do not twist wires).
Push the wires into wire nut (BB) and use your
fingers to twist the wire nut clockwise until tight.
Check for tightness by pulling wires.
6A
Securing the fixture and wiring
connections
(fig 1).
BB
Wall Mount
BB
Swivel Knuckle Flood Mount
(+) LINE
(-) COMMON
GROUND
BLACK
WHITE
GREEN
LIGHTING
FIXTURE
D
☐ Caulk around the mounting plate (D)
and surface with silicone sealant (not
included).
☐ If applicable, plug all unused holes and
seal threads with silicone.
8A/B
☐ Loosen the screw on swivel portion of
the knuckle (B), adjust the fixture to a
suitable orientation, and then tighten
the screw.
☐ Restore power to the breaker and light
switch and test if light turns on.
Caulking around the
light fixture
Adjusting the light
head and testing
B
Plug unused
holes, if any
Swivel Knuckle Flood Mount
Seal around
hole
D
Use the hex screw
here to adjust the
orientation using
provided allen key
(CC)
Wall/Eave Mount
☐ Once the fixture is wired, place the
fixture on the mounting plate and use
the two screws(E) to tighten the fixture
on the plate (D) by using the allen key
(CC).
8
Visit www.probrite.com/install for installation video tutorials and product support
CC
D
E
B
9
Please call 1-844-507-5651 or email [email protected] for further assistance.
Use the hex screw
here to adjust the
orientation using
provided allen key
(CC)
PROBRITE.COM
Page 6
Operation
Troubleshooting
Selecting Dusk-to-Dawn or
1
Switch-Activated control
OPTION 1: DUSK-TO-DAWN OPERATION
Dusk-to-dawn operation enables the light fixture to automatically turn
ON when dark outside and turn OFF when the sun rises, thus saving you
energy.
Swap
☐ To enable dusk-to-dawn operation
remove black cap cover (H) and ensure
the photocell has clear cap cover (DD)
on it and is unobstructed.
☐ Ensure the switch powering the outlet
connected to the light fixture is turned
to the ON position and leave it ON
at all times to enable dusk-to-dawn
functionality to operate automatically.
TIP: To test if the light fixture (A) and
photocell (B) works properly run power to
the fixture and cover the photocell to turn
fixture ON. Shine a light into the photocell to
see if fixture turns OFF.
Remove Opaque Cap Cover (DD )and
replace with Clear Cap Cover (H) on
photocell for Dusk-to-Dawn Operation
H
A
NOTE: If photocell (B) is located in an area
under heavy shade the photocell may not
detect enough light and may turn the light
fixture on. Either move fixture to less shaded
area or operate as normal switch-controlled
OPTION 2: SWITCH-CONTROLLED
Switch-controlled operation enables the light fixture to turn ON and OFF by
flipping a standard light switch.
☐ Once the fixture is installed, turn power
back on from the circuit breaker and
switch.
☐ Flip switch ON and OFF to ensure light
functions properly.
DD
AUTOMATIC
NIGHTTIME ON
DAYTIME OFF
SWITCH
CONTROLLED
Problem Possible Cause Solution
Check if circuit breaker is tripped
Confirm wall switch is ON
Verify wiring to fixture is correct
(turn power o to fixture
beforehand)
Cover photocell. Wait several
seconds until fixture turns ON.
Relocate light fixture to a location
where there is no reflected light.
OR place the optional photocell
cover over the photocell light
sensor and use the wall switch to
turn the light ON and OFF.
Do not use a dimmer switch to
control the light fixture. Replace
the dimmer with a standard
ON/OFF wall switch.
Shine a flashlight into the light
sensor and wait a couple minutes.
If the light turns OFF, the fixture
should be moved to a location
with enough light in the daylight
hours for the light sensor to work.
OR place the optional opaque
cover over the photocell light
sensor and use the wall switch to
turn the light ON and OFF.
If the light does not turn o when
a flashlight is shined on the light
sensor for a few minutes, then
the sensor may be faulty. Please
contact customer service.
Light does not
turn ON
Light cycles
ON and OFF
continuously
Light
FLICKERS
Light stays ON
No power to the fixture
Fixture is sensing daylight
Photocell light sensor is sensing reflected light
The light fixture is wired
through a dimmer switch.
Light sensor is in a shaded
area
Light Sensor is faulty
NOTE: This fixture is not dimmable, so it
is best to not wire to a dimming switch.
10
Visit www.probrite.com/install for installation video tutorials and product support
NOTE: Photocell may have a few minute delay, to reduce it's sensitivity
to sudden light changes. When testing shine a light/cover the
photocell for a few minutes to check if fixture functions properly
11
Please call 1-844-507-5651 or email [email protected] for further assistance.
PROBRITE.COM
Page 7
Care and Cleaning
☐ Shut o main power supply before cleaning the product. To prolong the original
appearance, clean the light fixture with clear water and a soft, damp cloth only.
☐ Do not use abrasive cleaners or cleaners that contain alcohol. Do not apply paints,
solvents, or any other chemicals on this light fixture. They could cause a premature
deterioration of the finish and may void the warranty.
☐ Do not spray the light fixture with a hose or power washer.
5-Year Limited Warranty
This is a limited warranty oered by Probrite for a period of five years from the date of purchase
to its customers. Probrite warrants to customers that the products will be free from defects
in material and workmanship. The obligation of Probrite under this warranty is limited to the
provision of replacement of products and is extended to the original purchaser of the product
on presenting valid purchase receipt or other proof of date of original purchase acceptable to
Probrite. The receipt is required for rendering the warranty performance. Any warranty claims
without original proof of purchase would not be accepted.
It should be noted that the warranty does not apply to Probrite products that have been
altered or repaired by unauthorized personnel, have been subjected to neglect, abuse, misuse
or accident or damages caused during shipping. Any other products not manufactured by
Probrite which have been supplied, installed and/or used in conjunction with Probrite products
are not covered under this warranty. Any damages caused by replacements bulbs, LEDs or
corrosion or discoloration of brass components are also not covered by this warranty.
Limitation of Liability:
In no event Probrite shall be liable for indirect, consequential, incidental or special damages, or
lost profits. Probrite is not liable for any claims or damage arising out of or connected with the
manufacture, sale, delivery, use, maintenance and repair or modification of Probrite products,
or supply of any replacement parts that, exceed the purchase price of Probrite products giving
rise to a claim. Labor charges to remove or install the fixtures will not be accepted.
To Claim:
Please contact PROBRITE customer service at 1-844-507-5651 or email support@PROBRITE.
com and include your name, address and contact number, along with a copy of the purchase
receipt and a brief description of the problem.
12
Visit www.probrite.com/install for installation video tutorials and product support
13
Please call 1-844-507-5651 or email [email protected] for further assistance.
PROBRITE.COM
Page 8
Questions? / Missing Parts? / Need Accessories?
Before returning to the store, call or email PROBRITE
Customer Service 9am-5pm EST Monday to Friday.
1-844-507-5651
PROBRITE.COM
RETAIN THIS MANUAL FOR FUTURE USE
Para las translaciones en español,
visit www.probrite.com/install
Loading...