PRM PR736, PR7310, PR738 Operating Manual & Parts List

operating manual & parts list PR736, PR738 and PR7310
6, 8& 10
BENCH GRINDER
Read carefully and follow all safety rules and operating instructions before first use of this product.
36626.00-0912
PR736, PR738 and PR7310
DESCRIPTION
PRM Bench Grinders are equipped with a totally enclosed ball bearing motor. Armature assembly is dynamically balanced for smooth operation. Motor housing is compact so long pieces of work can press against both wheels without touching the motor frame. Removable wheel guards allow for easy changing of wheels. Two-way tool rests are adjustable for wheel wear and angle grind­ing. Grinders come complete with spark guards, safety eyeshields and dust collection hose. (Dust Collection hose not included with PR736).
UNPACKING
Check for shipping damage. If damage has occurred, a claim must be filed with the carrier immediately. Check for completeness. Immediately report missing parts to dealer.
To be certain the grinding wheels have not been damaged in ship­ment, strike the edges slightly with a metal object. A ringing sound indicates a good wheel, but a dull noise may signal a fracture.
WARNING: If you suspect a wheel of being fractured, replace it
immediately. Fractured wheels may shatter, causing serious injury.
SPECIFICATIONS
PR736 - 6” Bench Grinder
Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120/240
Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5/1.75
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Single
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3450
Rotation (viewed from left side) . . . . . . . . . . . . . . . . . . . . . . . . .Clockwise
Wheel diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6”
Wheel bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PR738 - 8” Bench Grinder
Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120/240
Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7.0/3.5
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Single
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3450
Rotation (viewed from left side) . . . . . . . . . . . . . . . . . . . . . . . . .Clockwise
Wheel diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8”
Wheel bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PR7310 - 10” Bench Grinder
Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120/240
Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.0/5.0
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Single
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1725
Rotation (viewed from left side) . . . . . . . . . . . . . . . . . . . . . . . . .Clockwise
Wheel diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10”
Wheel bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1”
1
5
SAFETY RULES
WARNING: For your own safety, read operating instructions man-
ual before operating tool.
CAUTION: Always follow proper operating procedures as defined in
this manual even if you are familiar with use of this or similar tools. Remember that being careless for even a fraction of a second can result in severe personal injury.
WARNING: Some dust created by power sanding, sawing, grind-
ing, drilling and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
Lead from lead-based paints.
Crystalline silica from bricks and cement and other masonry
products.
Arsenic and chromium from chemically-treated lumber. Your risk from these exposures vary, depending on how often you
do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools.
BE PREPARED FOR JOB
Wear proper apparel. Do not wear loose clothing, gloves, neck­ties, rings, bracelets or other jewelry which may get caught in
1
/3
/2
3
/4
/8
moving parts of machine.
Wear protective hair covering to contain long hair.
Wear safety shoes with non-slip soles.
Wear safety glasses complying with United States ANSI Z87.1.
Everyday glasses have only impact resistant lenses. They are NOT safety glasses.
Wear face mask or dust mask if operation is dusty.
Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause drowsiness.
PREPARE WORK AREA FOR JOB
Keep work area clean. Cluttered work areas and work benches invite accidents.
Do not use power tools in dangerous environments. Do not use power tools in damp or wet locations. Do not expose power tools to rain.
Work area should be properly lighted.
Proper electrical plug should be plugged directly into properly
grounded, three-prong receptacle.
Extension cords should have a grounding prong and the three wires of the extension cord should be of the correct gauge.
Keep visitors at a safe distance from work area.
Keep children out of the workplace. Make workshop childproof.
Use padlocks, master switches or remove switch keys to pre­vent any unintentional use of power tools.
TOOL SHOULD BE MAINTAINED
Always unplug tool prior to inspection.
Consult manual for specific maintaining and adjusting proce-
dures.
Keep tool clean for safest operation.
Remove adjusting tools. Form habit of checking to see that
adjusting tools are removed before turning machine on.
2
SAFETY RULES (CONTINUED)
Keep all parts in working order. Check to determine that the guard or other parts will operate properly and perform their intended function.
Check for damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other condition that may affect a tool’s operation.
A guard or other part that is damaged should be properly repaired or replaced. Do not perform makeshift repairs. (Use the parts list to order replacement parts.)
PR736, PR738 and PR7310
TOOL REST ASSEMBLY
Place tool rest (D) over tool rest bracket and secure in position
5
with
/16-18 x 1” knob (F).
I
H
J
G
K
KNOW HOW TO USE TOOL
Use right tool for job. Do not force tool or attachment to do a job for which it was not designed.
Disconnect tool from power when changing accessories such as grinding wheels, buffing wheels and the like.
Avoid accidental start-up. Make sure that the switch is in the off position before plugging in.
Do not force tool. It will work most efficiently at the rate for which it was designed.
Keep hands away from moving parts and grinding surfaces.
Never leave a tool running unattended. Turn the power off and
do not leave tool until it comes to a complete stop.
Do not overreach. Keep proper footing and balance.
Never stand on tool. Serious injury could occur if tool is tipped
over.
Know your tool. Learn the tool’s operation, application and spe­cific limitations.
Use recommended accessories. Understand and obey all safety instructions supplied with accessories. The use of improper accessories may cause risk of injury to persons.
Do not over tighten wheel nut. Replace cracked wheel immedi­ately. Use only flanges supplied with the grinder.
Adjust distance between wheel and tool rest to maintain
1
/16” or
less gap.
Handle the workpiece correctly. Whenever possible, use tool rest to support workpiece during grinding operation. Turn tool off if it jams.
Always use guards and eyeshields.
Clean grinding dust from beneath tool frequently.
ASSEMBLY
Parts to be fastened to the unit should be located and accounted for (See List and Figure 1).
IMPORTANT: Do not attempt assembly if parts are missing. Use this manual to order replacement parts.
3
A
/8-16 x 3/4” Hex head bolt, 2 each
3
B
/8” Flat washer, 4 each C Tool rest bracket (left & right), 2 each D Tool rest (left & right), 2 each
5
E
/16” Flat washer, 2 each
5
F
/16-18 x 1” Knob, 2 each G #10-24 x H Upper eyeshield bracket (left & right), 2 each I Eyeshield, 2 each J Lower eyeshield bracket, 2 each
1
K
4-20 x 1⁄2” Knob, 2 each L Spark guard (left & right), 2 each
3
M
/8-16 x 1⁄2” Knob, 2 each Dust collector hose not shown.
3
8” Pan head screw, 4 each
L
B
M
C
D
B
A
E
F
Figure 1 – Left Tool Rest and Eyeshield Assembly
Attach tool rest bracket to the bottom of the left wheel guard
3
using one
8-16 x 3⁄4” heax head bolt (A) and one 3⁄8” flat wash­er (B). Make sure that the slot of the braket is located over the raised boss on the guard. Tight bolts finger tight.
Position tool rest so that distance between tool rest and grind­ing wheel is less than
1
/16”. Reposition angle of tool rest if neces-
sary. Secure all knobs and bolts.
Mount right tool rest in a similar manner.
EYESHIELD ASSEMBLY
3
Attach spark guard (L) to left wheel guard using knob (M) and
3
/8” flat washer (B).
8-16 x 1⁄2
Mount left upper eyeshield bracket (H) to eyeshield (I) using two #10-24 x
3
8” pan head screws (G) ad lower eyeshield
bracket.
NOTE: Left upper eyeshield bracket is stamped “L” for identification.
Slide
1
/4-20 x 1/2” knob (K) through hole at top of left spark guard (L) into upper upper eyeshield bracket (H) and secure in position.
Locate eyeshield in desired position for protecting operator and secure all knobs and bolts.
Mount right eyeshield assembly in a similar manner.
DUST COLLECTOR HOSE
A dust collector hose has been provided with grinder. Slide hoses onto sides of T-connector and flanges. Mount the hose by sliding the flanges at each end over the exhaust ports on the left and right wheel guards. Attach 2½” shop vacuum hose to collector hose. Be sure hose is mounted securely.
DANGER: Be sure to empty shop vacuum of all flammable materi-
al (flammable liquids and vapors, paper, wood, plastic, etc.) before connecting vacuum to grinder. Hot sparks from grinder may ignite flammable materials in shop vacuum.
3
INSTALLATION
MOUNT GRINDER
Mount grinder to a solid horizontal surface (hardware not pro­vided). If mounted to metal pedestal, align mounting holes with corresponding holes in pedestal. Insert a head bolt with flat washer through base of grinder. From bot­tom of pedestal, place a the bolt. Tighten only until space between grinder base and pedestal is
1
/8” (base should be flush for PR7310). Using second
1
/4” flat washer and 1/4”-20 hex nut onto
nut on each bolt, jam tighten against the first to prevent loos­ening by vibration.
To mount grinder to wooden bench top, use screws with flat washers beneath heads. Tighten screws until space between grinder base and bench top is be flush for PR7310).
GROUNDING INSTRUCTIONS WARNING: Improper connection of equipment grounding con-
ductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect operator from electrical shock.
Check with a qualified electrician if grounding instructions are not understood or if in doubt as to whether the tool is properly grounded.
This grinder is equipped with an approved 3-conductor cord rated at 300V and a 3-prong, grounding type plug (See Figure
2) for your protection against shock hazards.
Grounding plug should be plugged directly into a properly installed and grounded 3- prong grounding-type receptacle (See Figure 2).
Properly Grounded Outlet
Grounding Prong
3-Prong Plug
1
/4-20 x 1¼” hex
1
/4 x 1¼” wood
1
/8” (base should
PR736, PR738 and PR7310
A temporary 3-prong to 2-prong grounding adapter (See Figure 3) is available for connecting plugs to a two pole outlet if it is properly grounded.
Grounding Lug
Adapter
3-Prong Plug
Figure 3 – 2-Prong Receptacle
Make sure this is Connected to a known Grounded Receptacle
2-Prong Receptacle
Do not use a 3-prong to 2-prong grounding adapter unless permitted by local and national codes and ordinances.
(A 3-prong to 2-prong grounding adapter is not permitted in Canada.) Where permitted, the rigid green tab or terminal on the side of the adapter must be securely connected to a per­manent electrical ground such as a properly grounded water pipe, a properly grounded outlet box or a properly grounded wire system.
Many cover plate screws, water pipes and outlet boxes are not properly grounded. To ensure proper ground, grounding means must be tested by a qualified electrician.
EXTENSION CORDS
The use of any extension cord will cause some drop in voltage and loss of power.
Wires of the extension cord must be of sufficient size to carry the current and maintain adequate voltage.
Running the unit on voltages which are not within ±10% of the specified voltage may cause overheating and motor burn-out.
Use the table to determine the minimum wire size (A.W.G.) extension cord.
Use only 3-wire extension cords having 3-prong grounding type plugs and 3-pole receptacles which accept the tool plug.
If the extension cord is worn, cut or damaged in any way, replace it immediately.
Figure 2 – 3-Prong Receptacle
Do not remove or alter grounding prong in any manner. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electrical shock.
WARNING: Do not permit fingers to touch the terminals of plug
when installing or removing from outlet.
Plug must be plugged into matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify plug provided. If it will not fit in out­let, have proper outlet installed by a qualified electrician.
Inspect tool cords periodically, and, if damaged, have repaired by an authorized service facility.
Green (or green and yellow) conductor in cord is the grounding wire. If repair or replacement of the electric cord or plug is nec­essary, do not connect the green (or green and yellow) wire to a live terminal.
Where a 2-prong wall receptacle is encountered, it must be replaced with a properly grounded 3-prong receptacle installed in accordance with National Electric Code and local codes and ordinances.
WARNING: This work should be performed by a qualified
electrician.
EXTENSION CORD LENGTH (120 VOLTS) Model PR736
Wire Size A.W.G.
Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
25 - 100 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
100 - 150 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
NOTE: Using extension cords over 150 ft. long is not recommended.
EXTENSION CORD LENGTH (120 VOLTS) Model PR738 and PR7310
Wire Size A.W.G.
Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
25 - 50 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
50 - 100 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
100 - 150 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
NOTE: Using extension cords over 150 ft. long is not recommended.
EXTENSION CORD LENGTH (240 VOLTS) Model PR736, PR738 and PR7310
Wire Size A.W.G.
Up to 50 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
50 - 200 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
200 - 300 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
100 - 150 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
NOTE: Using extension cords over 300 ft. long is not recommended.
4
INSTALLATION (CONTINUED)
ELECTRICAL CONNECTIONS WARNING: All electrical connections must be performed by a
qualified electrician. Make sure tool is off and disconnected from power source while motor is mounted, connected, reconnected or anytime wiring is inspected.
Motor and wires are installed as shown in wiring diagram (See
Figure 4, page 5). Motor is assembled with approved, 3-conduc­tor cord to be used at 120/240 volts. Motor is prewired at the factory for 120 volts.
To use the grinder with a 240V power supply, have a qualified
electrician rewire motor and attach a 240 volt, I5A three-prong plug onto grinder line cord.
3-Red 2-Gray
1-Black
120V
3-Red
4-Yellow
2-Gray
PR736, PR738 and PR7310
MAINTENANCE
As wheels wear, tool rests should be positioned closer to the face of the wheels.
The gap between the wheel and the tool rest should not be greater than
1
the
/16” maximum gap cannot be maintained, the wheels
should be replaced.
Models PR736 and PR738: Replacement wheels should have a minimum rated speed of at least 3600 RPM.
Model PR7310: Replacement wheels must have a minimum rated speed of 1800 RPM.
Maximum wheel diameter is 6” for PR736, 8” for PR738, and 10” for PR7310.
To loosen nuts holding the wheels, disconnect power and push a wood wedge between the tool rest and the wheel to keep the shaft from turning. The threads on the right side of the grinder (facing unit) are right hand; threads on the left side are left hand. Tighten nuts securely before operating the grinder.
For grinding efficiency, wheels should be dressed periodically, especially if they become clogged from grinding soft metals.
1
/16”. When the wheels are worn to the extent that
WARRANTY
1-Black
240V
Figure 4 – Wiring Diagram
4-Yellow
OPERATION
WARNING: Always wear safety glasses complying with United
States ANSI Z87.1 (shown on package) before commencing power tool operation.
Keep a steady, moderate pressure on the work and keep it moving at an even pace for smooth grinding.
Pressing too hard overheats the motor and prematurely wears down the grinding wheels.
Note the original bevel angle on the item to be sharpened and try to maintain that angle. Sharpening a cutting edge requires removing burrs from edge.
Deburring edge is done best by using the grinder to pull burr from edge across the bevel angle.
The grinding wheel should rotate into object being sharpened.
Dip work into a coolant regularly to prevent overheating.
Overheating can weaken metals.
PRM warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a purpose other than that for which it was intended. The warranty does not cover expendable and/or wear parts (i.e. v-belts, coated screws, abrasives), damage to tools arising from alteration, abuse or use other than their intended purpose, packing and freight. The duration of this warranty is expressly lim­ited to one year parts and labor, unless otherwise noted below beginning from the date of delivery to the original user.
The obligation of PRM is limited solely to the repair or replace­ment, at our option, at its factory or authorized repair agent of any part that should prove deficient. Purchaser must lubricate and maintain the product under normal operating conditions at all times. Prior to operation become familiar with product and the included materials, i.e. warnings, cautions and manuals. Failure to
follow these instructions will void the warranty.
This warranty is the purchaser’s exclusive remedy against PRM for any deficiency in its products. Under no circumstances is PRM liable for any direct, indirect, incidental, special or consequential damages including lost profits in any way related to the use or inability to use our products. This warranty gives you specific legal rights which may vary from state to state.
5
PR736
20
1
3
43
15
10
16
30
14
39
32
31
35
34
42
33
37
36
38
19
20
24
5
9
22
8
6
2
11
24
21
25
26
11
24
39
29
28
27
11
26
25
42
23
17
18
20
21
2
10
11
22
6
7
5
4
33
40
14
13
12
9
33
41
3
1
Figure 7 - Replacement Parts Illustration for 6” Bench Grinder
6
PR736
BENCH GRINDER
2” Knob 25816.00 2
1
4-20 x
1
4” Lock washer * 2
4”-20 Hex nut * 2
16-18 x 1” Knob 25812.00 2
1
1
5
2”-12 Hex nut (RH thread) 00548.00 1
1
No. Description Number Qty.
23 5mm-0.8 Hex nut * 2
24
25 Endshield 16617.02 2
26 Bearing 6202ZZ 01540.00 2
27 Motor fan 01608.00 1
28 Armature 1
29 Stator with housing 1
30 Grommet 01066.00 1
31 Line cord 00067.00 1
32 Strain relief 04055.00 1
33 #10-24 x 1/4” Flange screw 3210.00 6
34 Base 23757.02 1
35 Rocker switch with key 08066.01 1
36 Cover 23758.00 1
37
38
39
40 Capacitor 16908.00 1
41 Bumper 23991.00 4
42 #10 Serrated washer * 3
Ref. Part
43
REPLACEMENT PARTS LIST FOR 6
2” Pan head screw * 6
1
2”-12 Hex nut (LH thread) 00064.00 1
1
5 Flange 18904.00 2
1 #10-24 x
2 Spark guard (set of 2) 30014.00 1
Ref. Part
No. Description Number Qty.
3 Wheel guard cover 24462.02 2
6 Inner wheel flange 17315.00 2
4
8” Flange screw 16670.00 6
4” Hex head bolt * 2
3
3
4-20 x
8-16 x
8” Flat washer * 4
1
3
3
7 Grinding wheel (36 coarse grit) 02034.00 1
8 Grinding wheel (60 med. grit) 02033.00 1
9
10
11
16” Flat washer * 2
5
12 Bracket (left) 25810.00 1
13 Tool rest (left) 25813.00 1
14
8” Pan head screw * 4
3
15 Bracket (right) 25826.00 1
18 Upper eyeshield bracket (left) 25177.00 1
16 Tool rest (right) 25825.00 1
17 #10-24 x
2” Knob 25817.00 2
1
8-16 x
3
Not Shown.
* Standard hardware item available locally.
19 Upper eyeshield bracket (right) 25188.00 1
20 Eyeshield kit 32290.00 1
21
22 Wheel guard 25986.00 2
† Not available as a repair part.
7
PR738
23
1
22
23
14
4
6
5
9
7
12
2
19
26
45
15
27
41
48
47
29
30
12
25
11
31
13
32
10
33
38
39
43
18
46
37
44
19
14
23
24
37
49
30
29
12
47
28
23
42
34
36
35
11
12
3
2
23
21
41
45
37
17
41
27
7
8
5
4
40
10
13
16
20
1
Figure 7 - Replacement Parts Illustration for 8” Bench Grinder
8
PR738
BENCH GRINDER
4” Flange screw 7
4” Flange screw 03210.00 9
1
2” Hex head bolt * 6
1
4-20 x
1
1
4” Lock washer * 8
4”-20 Hex nut * 2
1
1
Ref. Part
No. Description No. Qty.
28 5-0.8 x 228mm Flange screw 16654.00 4
29 Endshield 16627.02 2
30 Bearing 6204ZZ 00989.00 2
31 Motor fan 22041.00 1
32 Armature 1
33 Stator with housing 1
34 Grommet 01066.00 1
35 Line cord 00090.00 1
36 Strain relief 04055.00 1
37 #10-24 x
38 Base 24499.02 1
39 Switch with key 08066.01 1
40 Base cover 24500.00 1
26 5-0.8 mm Hex nut * 4
27
37 #10-24 x
41
42
43 Capacitor clamp 16655.00 1
44 Capacitor 16646.00 1
45 #10 Serrated washer * 5
46 Base bumper 23991.00 4
47 Wavy washer 16640.00 2
Operators manual 36626.00 1
48 Bracket (right) 31448.00 1
49 Centrifugal switch 25172.00 1
REPLACEMENT PARTS LIST FOR 8
8” Pan head screw 10
2” Pan head screw * 10
7
1
8”-11 Hex nut (LH thread) 00088.00 1
5
7 Inner wheel flange 24498.00 2
1 #10-24 x
1 #10-24 x
2 Wheel guard 26056.00 2
3 Spark guard (set of 2) 25815.00 1
4 Wheel guard cover 24496.02 2
Ref. Part
No. Description No. Qty.
5 Flange 24497.00 2
8 Grinding wheel (36 coarse grit) 02038.00 1
6
4” Hex head bolt * 2
3
16-18 x 1” Knob 25812.00 2
8-16 x
5
3
3
9 Grinding wheel (60 med. grit) 02037.00 1
11
10
8” Flat washer * 4
12
8” Knob 25816.00 2
3
16” Flat washer * 2
4-20 x
5
1
13
15 Dust collector hose 08070.00 1
14
8” Flange screw 03207.00 1
3
2” Knob 25817.00 2
1
8-16 x
8”-11 Hex nut (RH thread) 00087.00 1
3
5
Not Shown.
21 Upper eyeshield bracket (left) 25177.00 1
22 Upper eyeshield bracket (right) 25788.00 1
23 Eyeshield kit 32290.00 1
24 Stationary switch 25171.00 1
16 Tool rest (left) 25813.00 1
17 Bracket (left) 31447.00 1
18 #10-24 x
20
19
25 Tool rest (right) 25825.00 1
* Standard hardware item available locally.
† Not available as a repair part.
9
PR7310
1
23
4
22
23
5
9
25
7
51
27
41
26
3
12
20
24
29
19
24
20
28
12
11
30
49
2
32
15
12
33
48
35
34
18
36
17
14
47
42
43
10
46
46
46
45
44
2
14
50
17
16
46
39
2
37
31
30
40
41
38
11
12
29
28
3
41
23
21
23
26
7
8
5
6
4
27
1
13
Figure 8 - Replacement Parts Illustration for 10” Bench Grinder
10
PR7310
BENCH GRINDER
4” Flange screw 03210.00 10
8” Hex head bolt * 6
5
16-18 x
4-20 x 2” Flange screw 03209.00 8
5
1
16” Lock washer * 10
16”-18 Hex nut * 4
5
5
1
No. Description Number Qty.
28
27
29 Endshield 16913.02 2
30 Bearing 6206ZZ 00297.00 2
31 Motor fan 01639.00 1
32 Armature 1
33 Stator with housing 1
34 Grommet 16916.00 2
35 Line cord 00090.00 1
36 Strain relief 01601.00 1
37 Strain relief plate 08172.00 1
38 Base 16917.02 1
Ref. Part
39 Switch with key 08066.01 1
42
43 Capacitor clamp 16918.00 1
40 Switch plate 08173.00 1
41
44 Capacitor 08174.00 1
47 #10 Serrated washer * 1
48 Stationary switch 08175.00 1
49 Rotating switch 00299.00 1
50 Base cover 16919.00 1
45 Capacitor cap 01638.00 2
46 #10-24 x
51 Bracket (right) 26291.00 1
REPLACEMENT PARTS LIST FOR 10
8” Flange screw 03207.00 3
3
4” Pan head screw * 10
3
4-20 x
1
3 Spark guard (Set of 2) 25815.00 1
1
2 #10-24 x
4 Wheel guard cover 16911.02 2
5 Flange 24480.00 2
6 1”-8 Hex nut (LH thread) 00111.00 1
7 Inner wheel flange 24481.00 2
Ref. Part
No. Description Number Qty.
8 Grinding wheel (36 coarse grit) 02040.00 1
4” Hex head bolt * 2
3
8-16 x
8” Flat washer * 4
12
16-18 x 1” Knob 25812.00 2
5
13 Bracket (left) 26290.00 1
14
3
3
9 Grinding wheel (60 med. grit) 02039.00 1
10 Capacitor 16895.00 1
11
16” Flat washer * 2
5
15 Dust collector hose 08070.02 1
16 Tool rest (left) 25813.00 1
17
8” Knob 25816.00 2
3
4-20 x
1
18 Tool rest (right) 25825.00 1
19 Wavy washer 16620.00 1
20
21 Upper eyeshield bracket (left) 25177.00 1
2” Knob 25817.00 2
1
8-16 x
3
Not Shown.
22 Upper eyeshield bracket (right) 25188.00 1
23 Eyeshield kit 32290.00 1
24
25 1”-8 Hex nut (RH thread) 00110.00 1
26 Wheel guard 26057.00 2
* Standard hardware item available locally.
† Not available as a repair part.
11
TROUBLESHOOTING
PR736, PR738 and PR7310
SYMPTOM
Grinder won’t start
Excessive vibration
Motor overheating
Fuses are being blown or circuit breakers are being tripped
Motor does not develop proper torque
POSSIBLE CAUSE(S)
1. Blown line fuse or tripped circuit breaker
2. Low line voltage
3. Material wedged between wheel and guard
4. Defective switch
5. Defective, blown capacitor
1. Improper mounting of grinder or accessories
2. Grinding wheel out of balance
3. Improper wheel mounting
1. Excess pressure required to grind material
2. Grinding on side of wheel
3. Motor not turning freely (without power)
1. Overloading due to binding
2. Defective plug
3. Defective cord
4. Defective switch
5. Motor wired for different line voltage
6. Faulty internal wiring
1. Motor wired for different line voltage
CORRECTIVE ACTION
1. If fuse is blown, replace with fuse of proper size. If breaker tripped, reset it
2. Check power supply for voltage and correct as needed
3. Turn grinder off and remove material
4. Replace switch
5. Replace capacitor
1. Remount
2. Dress wheels or replace wheels
3. Remount wheels, but rotate one wheel 90º with respect to its previous position. Other wheel should remain in its original position
1. Dress wheel or replace wheel with one of proper grit
2. Grind only on face of wheel
3. Clean around wheels and shaft and/or replace bearings
1. Clean around wheels and shaft and/or replace bearings
2. Replace plug
3. Replace cord
4. Replace switch
5. Rewire motor as per wiring diagram, (See Installation, Page 5)
6. Contact your PRM distributor
1. Rewire motor as per wiring diagram,
(See Installation, Page 5)
Loading...