PR Lighting PRO-PAR, PR-3040 User Manual

PRO-PAR

PR-3040

This product manual contains important information about the safe installation
and use of this projector. Please read and follow these instructions carefully and
keep this manual in a safe place for future reference.

PR LIGHTING LTD.

Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

2/6

Pro-Par manual.doc

SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE HPL LAMP 4
CHANGING THE LENS 5
KEEPING THE PROJECTOR CLEAN 5
POWER CONNECTIONS 5
TECHNICAL SPECIFICATIONS 6

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to
change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change
specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the
information herein, or any consequence arising from them.
Every apparatus has been tested completely and packed properly by the manufacturer. Please make sure the packing and
/ or the apparatus is in good condition before your installation and use. Should there be any damage caused by
transportation, consult your dealer and do not use the apparatus. But any damage caused by improper use will not be
assumed by the manufacturer and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Clear, flat lens (14° Round beam shape) (1 PCS) (Order code: 070050017)
Stipple lens (19° Round beam shape) (1 PCS) (Order code: 070050016)
Fewer facets lens (21° x 34° Oblong beam shape) (1 PCS) (Order code: 070050014)
Many facets lens (30° x 51° Oblong beam shape) (1 PCS) (Order code: 070050015)
Gel frame (For installing the paper filter colour) (1 PCS)
Barndoors (1 SET)
Tool for uninstalling the lens (1 PCS)
This manual (1 PCS)

Thank you for purchasing the product PRO-PAR, PR-3040.
This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.

The PRO-PAR is an innovative projector with an elegant housing made from high quality
aluminiun-alloy with an insulating painting finish. The product complies to CE norms and
standards. It can be hung easily and safely. The angle of inclination for the projector-body is
convenient to be adjusted. The light beam can reach a long distance and there are various kinds
of lenses for your choice to produce different light beam effects. You can also use colour filter
which is installed inside the gel frame to produce the desirable beam colour. The projector is
suitable for use in stage, disco, or artistic applications.

ACCESSORIES

INDEX

INTRODUCTION

3/6

Pro-Par manual.doc

The following points are important for safety as well as for the smooth
installation and performance of the unit.

When unpacking and before disposing of the package check there is no transportation damage
before using the projector. Should there be any damage caused by transportation, consult your
dealer and do not use the apparatus. Keep the package well for your possible future transportation.

The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from
rain and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other
fluids, or metallic objects.

The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.
Do not project the beam onto inflammable surfaces, minimum distance is 5m. 5m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and / or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.
Hot housing surface! It can reach above 200℃! Do not touch the housing of the projector with your

hand during operation.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-

cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out
the plug by tugging the power-cord.

Keep the lamp and lens clean. Do not touch the lamp-glass and lens with bare hand.
Switching the lamp on and off at short intervals will reduce the life of both the lamp and the

projector. Occasional breaks will prolong the life of both the lamp and the projector.
Always replace the lamp if it becomes damaged or deformed.
Always replace the lens if it becomes cracked or badly scratched.
Never run the projector without a lamp and a lens in place.

Always disconnect from the mains, when the device is not in use or before
cleaning it or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

SAFE USAGE OF THE PROJECTOR

4/6

Pro-Par manual.doc

This unit has been designed to be hung. Hang the unit via its bracket using M12 size bolt(s).
When you want to adjust the angle of the body of the projector, you only loosen the locking knob
and then adjust the angle of the body. Always ensure that the projector is firmly positioned to
avoid vibration and slipping, and always ensure that the structure to which you are attaching the
projector is secure and is able to support a weight of 3.5kg for each PRO-PAR.
For safety the unit should have a secondary fixing with a safety cable through the two handles on
the back of the unit.

Important:

Before installation the HPL lamp verify that the HPL lamp you use is suitable for the
voltage at your facility. 115, 120, 230 and 240 volt HPL lamps are available. Operating lamps
beyond their rated voltage reduces lamp life and can cause premature lamp failure.

Loosen the knurled bolt on the back of the
lamp housing and pull the housing straight out
from the back of the fixture.
Remove the HPL lamp from its box, holding it
by the base.
Line up the flat sides of the lamp base with the
brackets on either side of the socket.
Push down on the lamp base until the lamp is
firmly seated. Make sure that the lamp is fully
seated, with the bottom of the lamp heat sink
flush to the lamp housing casting.
To reinstall the lamp housing, center it on the
reflector and the bolt hole, then tighten the
knurled bolt to secure the lamp housing in
place.

INSTALLING THE PROJECTOR

FITTING THE HPL LAMP

Locking Knob

Lens Rotation Ring

Handle

Safety Cable

HPL Lamp

Fixing Holes

Bracket

Lamp Housing

With the Retaining Clip
in Locked Position

Gel Frame

Lens

Barndoors

Knurled Bolt

Lamp Housing

Lamp-Bracket

Lamp Base

5/6

Pro-Par manual.doc

REMOVING A LENS

Unplug the fixture and let the fixture cool
sufficiently before handling the lens.

Place the fixture on a flat, stable work
surface. Do not install or remove lens
with the unit hanging.

It is easy to use the lens tool provided to
remove the lens. When uninstalling the
lens, let the middle tooth of the tool
push down the spring clip and the other
teeth will lift the edge of the lens from
the lens rotation ring.

INSTALLING A LENS

Hold the lens by the edge, and position
the convex side facing the front of the fixture.

Position the edge of the lens behind the tabs of the lens-rotation-ring and gently push the lens
inward until it snaps behind the spring clip.

To ensure the reliability of the projector it should be kept clean. The lens and reflector should be
regularly cleaned to maintain an optimum light output.

Do NOT use any glass cleaner or any type of solvent on the reflector. Before cleaning the
reflector remove the lens so you can access the reflector from the front of the fixture. When
cleaning the reflector use a damp, clean, soft, lint-free cotton cloth with amild, soapy water
solution and gently wipe the reflector, and then remove any soapy water residue with a clean, soft,
lint-free cotton cloth dampened with water. Do not use paper towels or harsh materials to wipe

the reflector.

Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft
cloth and typical glass cleaning products should be used in cleaning. It is recommended to clean
the lens at least once every 20 days and clean the reflector at least once every 30 / 60 days.

Do not use any organic solvent, e.g. alcohol, to clean the housing of the
projector.

The unit is supplied with a power cord. Should any other connections be required they must be
carried out with the following configuration: Earth = Green/Yellow cord.

CHANGING THE LENS

KEEPING THE PROJECTOR CLEAN

POWER CONNECTIONS

Tool for Uninstall the Lens

Lens With the

Convex Side Out

Spring Clip

Lens Rotation
Ring

6/6

Pro-Par manual.doc

Power supply: 230V AC 50Hz
Optional: 240V, 120V, 115V AC 50/60Hz
Power consumption: 575W at 220V
Lamp: HPL 575W/230V (Ave rated life: 400 hours)
Optional: HPL 375W/115V, 575W/120V, 575W/240V
Net Weight: 3.5kg

PR LIGHTING LTD.

Add: Yingbin Road, Dashi, Panyu, Guangzhou, China

Post-Code：511430

TEL：[phone]

FAX：[phone]

P/N: 321010050

Last Revision: 22:08:2002

TECHNICAL SPECIFICATIONS

0m

638 lux

0m

2m

4m

6m

5m
3m

1m

2m
4m

6m

5m

3m

1m

0m 5m 10m 15m 20m 25m

5750 lux 1437 lux 230 lux 160 lux

2.2m 4.5m 6.6m 8.8m 11m

30m

7m

7m

13m

25

DISTANCE
DIAMETER

359 lux

２８０

２９０

２８０

２４０

２３５